| Age | Commit message (Collapse) | Author |
|---|
|
The "perf_counter_reset" case has already been handled above.
Moreover "ORANGEFS_PARAM_REQUEST_OP_READAHEAD_COUNT_SIZE" is not a really
consistent.
It is likely that this (dead) code is a cut and paste left over.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Martin Brandenburg <martin@omnibond.com>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
|
|
* pci/host-vmd:
PCI: vmd: Fix suspend handlers defined-but-not-used warning
PCI: vmd: Use SRCU as a local RCU to prevent delaying global RCU
PCI: vmd: Remove unnecessary pci_set_drvdata()
|
|
* pci/host-tegra:
arm64: tegra: Enable PCIe on Jetson TX1
arm64: tegra: Add PCIe host bridge on Tegra210
PCI: tegra: Enable the driver on 64-bit ARM
PCI: tegra: Add Tegra210 support
PCI: tegra: Implement PCA enable workaround
dt-bindings: pci: tegra: Add Tegra210 support
PCI: tegra: Use new pci_register_host_bridge() interface
PCI: Export host bridge registration interface
PCI: Allow driver-specific data in host bridge
PCI: Add pci_register_host_bridge() interface
|
|
* pci/host-spear:
PCI: spear: Use builtin_platform_driver() to simplify the code
|
|
* pci/host-rockchip:
PCI: rockchip: Move the deassert of pm/aclk/pclk after phy_init()
PCI: rockchip: Split out rockchip_cfg_atu()
PCI: rockchip: Clean up bit definitions for PCIE_RC_CONFIG_LCS
PCI: rockchip: Correct the use of FTS mask
PCI: rockchip: Remove the pointer to L1 substate cap
PCI: rockchip: Specify the link capability
PCI: rockchip: Fix negotiated lanes calculation
PCI: rockchip: Add Kconfig COMPILE_TEST
PCI: rockchip: Mark RC as common clock architecture
PCI: rockchip: Provide captured slot power limit and scale
PCI: rockchip: Add three new resets as required properties
PCI: Don't attempt to claim shadow copies of ROM
PCI: designware: Check for iATU unroll support after initializing host
PCI: qcom: Fix pp->dev usage before assignment
PCI: designware-plat: Update author email address
PCI: layerscape: Fix drvdata usage before assignment
PCI: designware-plat: Change maintainer to Jose Abreu
|
|
* pci/host-rcar:
PCI: rcar: Add gen3 fallback compatibility string for pcie-rcar
PCI: rcar: Use gen2 fallback compatibility last
PCI: rcar-gen2: Use gen2 fallback compatibility last
|
|
* pci/host-qcom:
PCI: qcom: Add support for MSM8996 PCIe controller
|
|
* pci/host-layerscape:
PCI: layerscape: Add LS1046a support
PCI: layerscape: Remove redundant error message from ls_pcie_probe()
|
|
* pci/host-iproc:
PCI: iproc: Skip check for legacy IRQ on PAXC buses
PCI: iproc: Fix incorrect MSI address alignment
PCI: iproc: Add support for the next-gen PAXB controller
PCI: iproc: Add PAXBv2 binding info
PCI: iproc: Add inbound DMA mapping support
PCI: iproc: Add optional dma-ranges
PCI: iproc: Make outbound mapping code more generic
PCI: iproc: Remove redundant outbound properties
PCI: iproc: Add PAXC v2 support
PCI: iproc: Add PAXCv2 related binding
PCI: iproc: Fix exception with multi-function devices
PCI: iproc: Add BCMA type
PCI: iproc: Do not reset PAXC when initializing the driver
PCI: iproc: Improve core register population
|
|
* pci/host-imx6:
MAINTAINERS: Add devicetree binding to PCI i.MX6 entry
MAINTAINERS: Update Richard Zhu's email address
|
|
* pci/host-hv:
PCI: hv: Allocate physically contiguous hypercall params buffer
PCI: hv: Delete the device earlier from hbus->children for hot-remove
PCI: hv: Fix hv_pci_remove() for hot-remove
PCI: hv: Use the correct buffer size in new_pcichild_device()
PCI: hv: Make unnecessarily global IRQ masking functions static
|
|
* pci/host-hisi:
PCI: hisi: Remove redundant error message from hisi_pcie_probe()
|
|
* pci/host-altera:
PCI: altera: Remove redundant error message in altera_pcie_parse_dt()
PCI: altera: Use builtin_platform_driver() to simplify the code
|
|
* pci/host:
of/pci: Add of_pci_get_max_link_speed() to parse max-link-speed from DT
Documentation/devicetree: Add PCIe max-link-speed property
|
|
* pci/virtualization:
PCI: Add comments about ROM BAR updating
PCI: Decouple IORESOURCE_ROM_ENABLE and PCI_ROM_ADDRESS_ENABLE
PCI: Remove pci_resource_bar() and pci_iov_resource_bar()
PCI: Don't update VF BARs while VF memory space is enabled
PCI: Separate VF BAR updates from standard BAR updates
PCI: Update BARs using property bits appropriate for type
PCI: Ignore BAR updates on virtual functions
PCI: Do any VF BAR updates before enabling the BARs
PCI: Support INTx masking on ConnectX-4 with firmware x.14.1100+
PCI: Convert Mellanox broken INTx quirks to be for listed devices only
PCI: Convert broken INTx masking quirks from HEADER to FINAL
net/mlx4_core: Use device ID defines
PCI: Add Mellanox device IDs
|
|
* pci/pm:
x86/platform/intel-mid: Constify mid_pci_platform_pm
PCI: pciehp: Add runtime PM support for PCIe hotplug ports
ACPI / hotplug / PCI: Make device_is_managed_by_native_pciehp() public
ACPI / hotplug / PCI: Use cached copy of PCI_EXP_SLTCAP_HPC bit
PCI: Unfold conditions to block runtime PM on PCIe ports
PCI: Consolidate conditions to allow runtime PM on PCIe ports
PCI: Activate runtime PM on a PCIe port only if it can suspend
PCI: Speed up algorithm in pci_bridge_d3_update()
PCI: Autosense device removal in pci_bridge_d3_update()
PCI: Don't acquire ref on parent in pci_bridge_d3_update()
USB: UHCI: report non-PME wakeup signalling for Intel hardware
PCI: Check for PME in targeted sleep state
|
|
* pci/msi:
PCI/MSI: Check for NULL affinity mask in pci_irq_get_affinity()
|
|
* pci/misc:
PCI: Enable access to non-standard VPD for Chelsio devices (cxgb3)
PCI: Expand "VPD access disabled" quirk message
PCI: pciehp: Remove loading message
PCI: hotplug: Remove hotplug core message
PCI: Remove service driver load/unload messages
PCI/AER: Log AER IRQ when claiming Root Port
PCI/AER: Log errors with PCI device, not PCIe service device
PCI/AER: Remove unused version macros
PCI/PME: Log PME IRQ when claiming Root Port
PCI/PME: Drop unused support for PMEs from Root Complex Event Collectors
PCI: Move config space size macros to pci_regs.h
|
|
* pci/hotplug:
PCI: pciehp: Leave power indicator on when enabling already-enabled slot
PCI: pciehp: Prioritize data-link event over presence detect
PCI: cpqphp: Add missing call to pci_disable_device()
|
|
* pci/enumeration:
PCI: Warn on possible RW1C corruption for sub-32 bit config writes
PCI: Create revision file in sysfs
|
|
* pci/ecam:
PCI: Explain ARM64 ACPI/MCFG quirk Kconfig and build strategy
PCI: Add MCFG quirks for X-Gene host controller
PCI: Add MCFG quirks for Cavium ThunderX pass1.x host controller
PCI: Add MCFG quirks for Cavium ThunderX pass2.x host controller
PCI: thunder-pem: Factor out resource lookup
PCI: Add MCFG quirks for HiSilicon Hip05/06/07 host controllers
PCI: Add MCFG quirks for Qualcomm QDF2432 host controller
PCI/ACPI: Provide acpi_get_rc_resources() for ARM64 platform
PCI/ACPI: Check for platform-specific MCFG quirks
PCI/ACPI: Extend pci_mcfg_lookup() to return ECAM config accessors
arm64: PCI: Exclude ACPI "consumer" resources from host bridge windows
arm64: PCI: Manage controller-specific data on per-controller basis
arm64: PCI: Search ACPI namespace to ensure ECAM space is reserved
arm64: PCI: Add local struct device pointers
ACPI: Add acpi_resource_consumer() to find device that claims a resource
|
|
* pci/aspm:
PCI/ASPM: Don't retrain link if ASPM not possible
PCI/ASPM: Use permission-specific DEVICE_ATTR variants
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RCU updates from Ingo Molnar:
"The main RCU changes in this development cycle were:
- Miscellaneous fixes, including a change to call_rcu()'s rcu_head
alignment check.
- Security-motivated list consistency checks, which are disabled by
default behind DEBUG_LIST.
- Torture-test updates.
- Documentation updates, yet again just simple changes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
torture: Prevent jitter from delaying build-only runs
torture: Remove obsolete files from rcutorture .gitignore
rcu: Don't kick unless grace period or request
rcu: Make expedited grace periods recheck dyntick idle state
torture: Trace long read-side delays
rcu: RCU_TRACE enables event tracing as well as debugfs
rcu: Remove obsolete comment from __call_rcu()
rcu: Remove obsolete rcu_check_callbacks() header comment
rcu: Tighten up __call_rcu() rcu_head alignment check
Documentation/RCU: Fix minor typo
documentation: Present updated RCU guarantee
bug: Avoid Kconfig warning for BUG_ON_DATA_CORRUPTION
lib/Kconfig.debug: Fix typo in select statement
lkdtm: Add tests for struct list corruption
bug: Provide toggle for BUG on data corruption
list: Split list_del() debug checking into separate function
rculist: Consolidate DEBUG_LIST for list_add_rcu()
list: Split list_add() debug checking into separate function
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris
Pull CRIS updates from Jesper Nilsson:
"Three patches for minor issues"
* tag 'cris-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
cris: No need to append -O2 and $(LINUXINCLUDE)
tty: serial: make crisv10 explicitly non-modular
cris: Only build flash rescue image if CONFIG_ETRAX_AXISFLASHMAP is selected
|
|
In sirfsoc_dma_pm_suspend(), variable ‘sdesc’ is initialized but never used, which
leads to warning with W=1.
drivers/dma/sirf-dma.c: In function 'sirfsoc_dma_pm_suspend':
drivers/dma/sirf-dma.c:1014:27: warning: variable 'sdesc' set but not used [-Wunused-but-set-variable]
So remove it.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In pl330_add(), variable ‘regs’ is initialized but never used, which
leads to warning with W=1.
drivers/dma/pl330.c: In function 'pl330_add':
drivers/dma/pl330.c:1891:16: warning: variable 'regs' set but not used [-Wunused-but-set-variable]
So remove it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In s3c24xx_dma_get_phy(), variable ‘cdata’ is initialized but never used, which
leads to warning with W=1. Removing this make pdata unused.
drivers/dma/s3c24xx-dma.c: In function ‘s3c24xx_dma_get_phy’:
drivers/dma/s3c24xx-dma.c:293:30: warning: variable ‘cdata’ set but not used [-Wunused-but-set-variable]
struct s3c24xx_dma_channel *cdata;
So remove both of them.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In stm32_dma_set_xfer_param(), variable ‘src_addr’ is initialized but never used, which
leads to warning with W=1
drivers/dma/stm32-dma.c: In function ‘stm32_dma_set_xfer_param’:
drivers/dma/stm32-dma.c:577:13: warning: variable ‘src_addr’ set but not used [-Wunused-but-set-variable]
dma_addr_t src_addr, dst_addr;
So remove it.
Reviewed-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In stm32_dma_set_xfer_param(), variable ‘dst_addr’ is initialized but never used, which
leads to warning with W=1
drivers/dma/stm32-dma.c: In function ‘stm32_dma_set_xfer_param’:
drivers/dma/stm32-dma.c:577:23: warning: variable ‘dst_addr’ set but not used [-Wunused-but-set-variable]
dma_addr_t src_addr, dst_addr;
So remove it.
Reviewed-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In stm32_dma_chan_irq(), variable ‘sfcr’ is initialized but never used, which
leads to warning with W=1
drivers/dma/stm32-dma.c: In function ‘stm32_dma_chan_irq’:
drivers/dma/stm32-dma.c:530:19: warning: variable ‘sfcr’ set but not used [-Wunused-but-set-variable]
u32 status, scr, sfcr;
So remove it.
Reviewed-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In pd_tx_submit(), variable ‘cookie’ is initialized but never used, which
leads to warning with W=1
drivers/dma/pch_dma.c: In function ‘pd_tx_submit’:
drivers/dma/pch_dma.c:420:15: warning: variable ‘cookie’ set but not used [-Wunused-but-set-variable]
dma_cookie_t cookie;
So remove it.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In mic_dma_init(), variable ‘data’ is initialized but never used, which
leads to warning with W=1
drivers/dma/mic_x100_dma.c: In function ‘mic_dma_init’:
drivers/dma/mic_x100_dma.c:557:17: warning: variable ‘data’ set but not used [-Wunused-but-set-variable]
unsigned long data;
So remove it.
Cc: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In mdc_prep_dma_memcpy(), mdc_prep_dma_cyclic() and mdc_prep_slave_sg()
variable ‘prev_phys’ is initialized but never used, which
leads to warning with W=1
drivers/dma/img-mdc-dma.c: In function ‘mdc_prep_dma_memcpy’:
drivers/dma/img-mdc-dma.c:295:24: warning: variable ‘prev_phys’ set but not used [-Wunused-but-set-variable]
dma_addr_t curr_phys, prev_phys;
drivers/dma/img-mdc-dma.c: In function ‘mdc_prep_dma_cyclic’:
drivers/dma/img-mdc-dma.c:378:24: warning: variable ‘prev_phys’ set but not used [-Wunused-but-set-variable]
dma_addr_t curr_phys, prev_phys;
drivers/dma/img-mdc-dma.c: In function ‘mdc_prep_slave_sg’:
drivers/dma/img-mdc-dma.c:461:24: warning: variable ‘prev_phys’ set but not
used [-Wunused-but-set-variable]
dma_addr_t curr_phys, prev_phys;
So remove it.
Cc: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In usb_dmac_of_xlate(), variable ‘uchan’ is initialized but never used, which
leads to warning with W=1
drivers/dma/sh/usb-dmac.c: In function ‘usb_dmac_of_xlate’:
drivers/dma/sh/usb-dmac.c:655:24: warning: variable ‘uchan’ set but not used [-Wunused-but-set-variable]
struct usb_dmac_chan *uchan;
So remove it.
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In __cleanup(), variable ‘res’ is initialized but never used, which
leads to warning with W=1
drivers/dma/ioat/dma.c: In function ‘__cleanup’:
drivers/dma/ioat/dma.c:614:28: warning: variable ‘res’ set but not used [-Wunused-but-set-variable]
struct dmaengine_result res;
So remove it.
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In ioat_tx_submit_unlock(), variable ‘ioat_dma’ is initialized but never
used, which leads to warning with W=1
drivers/dma/ioat/dma.c: In function ‘ioat_alloc_ring_ent’:
drivers/dma/ioat/dma.c:341:25: warning: variable ‘ioat_dma’ set but not used [-Wunused-but-set-variable]
struct ioatdma_device *ioat_dma;
So remove it.
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In ioat3_dma_probe(), variable ‘is_raid_device’ is initialized but never
used, which leads to warning with W=1
drivers/dma/ioat/init.c: In function ‘ioat3_dma_probe’:
drivers/dma/ioat/init.c:1084:7: warning: variable ‘is_raid_device’ set
but not used [-Wunused-but-set-variable]
bool is_raid_device = false;
So remove it.
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Pull Openrisc updates from Stafford Horne:
- changes to MAINTAINER for openrisc
- probably biggest actual change is the move to memblock from bootmem
- ... plus several bug and build fixes
* tag 'openrisc-for-linus' of git://github.com/openrisc/linux:
openrisc: prevent VGA console, fix builds
openrisc: include l.swa in check for write data pagefault
openrisc: Updates after openrisc.net has been lost
openrisc: Consolidate setup to use memblock instead of bootmem
openrisc: remove the redundant of_platform_populate
openrisc: add NR_CPUS Kconfig default value
openrisc: Support both old (or32) and new (or1k) toolchain
openrisc: Add thread-local storage (TLS) support
openrisc: restore all regs on rt_sigreturn
openrisc: fix PTRS_PER_PGD define
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
"Use seq_puts() for fixed strings"
* tag 'm68k-for-v4.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/atari: Use seq_puts() in atari_get_hardware_list()
m68k/amiga: Use seq_puts() in amiga_get_hardware_list()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32
Pull AVR32 updates from Hans-Christian Noren Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
avr32: wire up pkey syscalls
AVR32-pio: Replace two seq_printf() calls by seq_puts() in pio_bank_show()
AVR32-pio: Use seq_putc() in pio_bank_show()
AVR32-clock: Combine nine seq_printf() calls into one call in clk_show()
AVR32-clock: Use seq_putc() in two functions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu updates from Greg Ungerer:
"There are two sets of changes in this pull.
The largest is the addition of the ColdFire platform side i2c support
(the IO addressing, setup and clock definitions). The i2c hardware
module itself is driven by the kernels existing iMX i2c driver.
The other change is the addition of support for the Amcore board"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: AMCORE board, add iMX i2c support
m68k: add Sysam AMCORE open board support
m68knommu: platform support for i2c devices on ColdFire SoC
|
|
allocates string 'new' is not free'd on the exit path when
cdm_element_count <= 0. Fix this by kfree'ing it.
Fixes CoverityScan CID#1375923 "Resource Leak"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
|
|
Pull sparc updates from David Miller:
"Just a bunch of small cleanups and fixes here, and support for user
probes from Allen Pais"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: fix a building error reported by kbuild
sparc64: fix typo in pgd_clear()
sparc64: restore irq in error paths in iommu
sparc: leon: Fix a retry loop in leon_init_timers()
sparc64: make string buffers large enough
sparc64: move dereference after check for NULL
sparc: kernel: use builtin_platform_driver
sparc64:Support User Probes for sparc
|
|
There is at least one Chelsio 10Gb card which uses VPD area to store some
non-standard blocks (example below). However pci_vpd_size() returns the
length of the first block only assuming that there can be only one VPD "End
Tag".
Since 4e1a635552d3 ("vfio/pci: Use kernel VPD access functions"), VFIO
blocks access beyond that offset, which prevents the guest "cxgb3" driver
from probing the device. The host system does not have this problem as its
driver accesses the config space directly without pci_read_vpd().
Add a quirk to override the VPD size to a bigger value. The maximum size
is taken from EEPROMSIZE in drivers/net/ethernet/chelsio/cxgb3/common.h.
We do not read the tag as the cxgb3 driver does as the driver supports
writing to EEPROM/VPD and when it writes, it only checks for 8192 bytes
boundary. The quirk is registered for all devices supported by the cxgb3
driver.
This adds a quirk to the PCI layer (not to the cxgb3 driver) as the cxgb3
driver itself accesses VPD directly and the problem only exists with the
vfio-pci driver (when cxgb3 is not running on the host and may not be even
loaded) which blocks accesses beyond the first block of VPD data. However
vfio-pci itself does not have quirks mechanism so we add it to PCI.
This is the controller:
Ethernet controller [0200]: Chelsio Communications Inc T310 10GbE Single Port Adapter [1425:0030]
This is what I parsed from its VPD:
===
b'\x82*\x0010 Gigabit Ethernet-SR PCI Express Adapter\x90J\x00EC\x07D76809 FN\x0746K'
0000 Large item 42 bytes; name 0x2 Identifier String
b'10 Gigabit Ethernet-SR PCI Express Adapter'
002d Large item 74 bytes; name 0x10
#00 [EC] len=7: b'D76809 '
#0a [FN] len=7: b'46K7897'
#14 [PN] len=7: b'46K7897'
#1e [MN] len=4: b'1037'
#25 [FC] len=4: b'5769'
#2c [SN] len=12: b'YL102035603V'
#3b [NA] len=12: b'00145E992ED1'
007a Small item 1 bytes; name 0xf End Tag
0c00 Large item 16 bytes; name 0x2 Identifier String
b'S310E-SR-X '
0c13 Large item 234 bytes; name 0x10
#00 [PN] len=16: b'TBD '
#13 [EC] len=16: b'110107730D2 '
#26 [SN] len=16: b'97YL102035603V '
#39 [NA] len=12: b'00145E992ED1'
#48 [V0] len=6: b'175000'
#51 [V1] len=6: b'266666'
#5a [V2] len=6: b'266666'
#63 [V3] len=6: b'2000 '
#6c [V4] len=2: b'1 '
#71 [V5] len=6: b'c2 '
#7a [V6] len=6: b'0 '
#83 [V7] len=2: b'1 '
#88 [V8] len=2: b'0 '
#8d [V9] len=2: b'0 '
#92 [VA] len=2: b'0 '
#97 [RV] len=80: b's\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00'...
0d00 Large item 252 bytes; name 0x11
#00 [VC] len=16: b'122310_1222 dp '
#13 [VD] len=16: b'610-0001-00 H1\x00\x00'
#26 [VE] len=16: b'122310_1353 fp '
#39 [VF] len=16: b'610-0001-00 H1\x00\x00'
#4c [RW] len=173: b'\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00'...
0dff Small item 0 bytes; name 0xf End Tag
10f3 Large item 13315 bytes; name 0x62
!!! unknown item name 98: b'\xd0\x03\x00@`\x0c\x08\x00\x00\x00\x00\x00\x00\x00\x00\x00'
===
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
It's not very enlightening to see
pci 0000:07:00.0: [Firmware Bug]: VPD access disabled
in the dmesg log because there's no clue about what the firmware bug is.
Expand the message to explain why we're disabling VPD.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Remove the "PCI Express Hot Plug Controller Driver" version message. I
don't think it contains any useful information. Remove unused #defines
and move the author information to a comment.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Remove the "PCI Hot Plug PCI Core" version message. I don't think it
contains any useful information. Remove unused #defines and move the
author information to a comment.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Remove the "service driver %s loaded" and unloaded messages. All service
drivers already log something in their probe functions, where they can log
more useful details.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Add a log message when we enable AER on a Root Port and the hierarchy below
it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
All other AER-related log messages use the PCI device, e.g.,
"pci 0000:00:1c.0", not the PCIe service device, e.g.,
"aer 0000:00:1c.0:pcie02".
Change the probe error messages to match the rest and include a little
context.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
