Age | Commit message (Collapse) | Author |
|
Not needed constant that was set to 0.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
These comments were covering removed struct at_dma_slave fields.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
|
|
for cyclic dma, dont makr the descriptor as complte. Fix the remaining users of
cyclic dma which do so
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Mika Westerberg <mika.westerberg@iki.fi>
|
|
Add support for Iomega Iconnect system.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-By: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
dns323 and (at least) iconnect platforms are using hw led blinking, so,
instead of having 2 identicals .gpio_blink_set gpio-led hooks, move
dns323 code into gpio.c
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-By: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
gpio registers are for 32 gpios. Given that orion_gpio_set_blink is called
directly and not through gpiolib, it needs to make sure that the pin value
given to the internal functions are between 0 and 31.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-By: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Use devicetree to define NAND partitions. Use D-link partition scheme by
default, to be vaguely compatible with their userland.
Changes since last submission (V4):-
* Don't add NAND support then throw it away immediately after [Grant Likely]
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Add default configuration for NAND, to be enabled in your board config. Ensure
clock gating is set appropriately when the NAND is enabled.
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Allow a NAND chip using the orion_nand driver to be described using devicetree.
Changes since last submission (V4) [Addressing comments by]:-
* WARN when bank-width is out of range [Andrew Lunn]
Changes since last submission (V3):-
* Document all parameters [Grant Likely]
* Convert bank-width to be in bytes
* Add explicit defaults for cle, ale and bank-width
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Add support for the DNS-320 and DNS-325. Describe as much as currently possible
in the devicetree files, create a board-dnskw.c for everything else.
Changes since last submission (V3) [Addressing comments by]:-
* One MACH_DLINK_KIRKWOOD_DT for all dtb files [Grant Likely, Jason Cooper]
* Drop brain-dead select "select CONFIG_MTD_OF_PARTS" [Grant Likely]
* Don't add NAND support then throw it away immediately after [Grant Likely]
* Describe purpose of MPP 41, 42 & 49
Changes since last submission (V2):-
* Use IEEE-compliant "okay", rather than "ok" [Scott Wood]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Without CRYPTO_HASH being selected, mv_cesa has a lot of hooks
into undefined exports.
----
MODPOST 81 modules
Kernel: arch/arm/boot/Image is ready
AS arch/arm/boot/compressed/head.o
GZIP arch/arm/boot/compressed/piggy.gzip
CC arch/arm/boot/compressed/misc.o
CC arch/arm/boot/compressed/decompress.o
ERROR: "crypto_ahash_type" [drivers/crypto/mv_cesa.ko] undefined!
ERROR: "crypto_shash_final" [drivers/crypto/mv_cesa.ko] undefined!
ERROR: "crypto_register_ahash" [drivers/crypto/mv_cesa.ko] undefined!
ERROR: "crypto_unregister_ahash" [drivers/crypto/mv_cesa.ko] undefined!
ERROR: "crypto_shash_update" [drivers/crypto/mv_cesa.ko] undefined!
ERROR: "crypto_shash_digest" [drivers/crypto/mv_cesa.ko] undefined!
ERROR: "crypto_shash_setkey" [drivers/crypto/mv_cesa.ko] undefined!
ERROR: "crypto_alloc_shash" [drivers/crypto/mv_cesa.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
make: *** Waiting for unfinished jobs....
----
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Cc: stable@vger.kernel.org
|
|
Fix kernel-doc warnings in sunrpc/rpc_pipe.c and
sunrpc/rpcb_clnt.c:
Warning(net/sunrpc/rpcb_clnt.c:428): No description found for parameter 'net'
Warning(net/sunrpc/rpcb_clnt.c:567): No description found for parameter 'net'
Warning(net/sunrpc/rpc_pipe.c:133): No description found for parameter 'pipe'
Warning(net/sunrpc/rpc_pipe.c:133): Excess function parameter 'inode' description in 'rpc_queue_upcall'
Warning(net/sunrpc/rpc_pipe.c:839): No description found for parameter 'pipe'
Warning(net/sunrpc/rpc_pipe.c:839): Excess function parameter 'ops' description in 'rpc_mkpipe_dentry'
Warning(net/sunrpc/rpc_pipe.c:839): Excess function parameter 'flags' description in 'rpc_mkpipe_dentry'
Warning(net/sunrpc/rpc_pipe.c:949): No description found for parameter 'dentry'
Warning(net/sunrpc/rpc_pipe.c:949): Excess function parameter 'clnt' description in 'rpc_remove_client_dir'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Obviously we should check for NULL here instead of IS_ERR().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org [3.4]
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Most users will use NFS v3 or possibly v4 so this makes it easier for
them.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
With this patch NFS v2 can be disabled during Kconfig. I default the
option to "y" to match the current behavior.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
In theory, NFS v3 can have different error versions than NFS v2. v4 is
already using its own nfs4_stat_to_errno() to map error codes, so
rather than create something in the generic client for v2 and v3 to
share I instead give v3 its own function.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
This allows me to use the filehandle allocated in nfs_fs_mount() for nfs
v4 mounts instead of allocating a new one. Rather than change
nfs4_mount() to look almost exactly like nfs_fs_mount(), I instead
remove the function.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
This new function chooses between the v2/3 parser and the v4 parser by
filesystem type.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
The v2/3 and v4 cases were very similar, with just a few parameters
changed. This makes it easy to share code.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
This function returns the same same return type as nfs4_try_mount() so
they two can be more easily substituted.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
This field is unconditionally set while parsing mount data, so there is
no need to fill it in here.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
At this point, there are only a few small differences between these two
functions. I can set a few function pointers in the nfs_mount_info
struct to get around these differences.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
The only difference between nfs_xdev_mount() and nfs4_xdev_mount() is the
clone_super() function called to clone the super block. I can combine
these two functions by using the fill_super field in the mount_info
structure.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
The nfs4_remote_mount() function was only slightly different from the
nfs_fs_mount() function used by the generic client. I created a new
nfs_mount_info structure to set different parameters to help combine
these functions.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
This flag is numerically equivalent to NFS_MOUNT_UNSHARED, so I can
remove it to make collapsing functions more straightforward.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
I intend on creating a single nfs_fs_mount() function used by all our
mount paths. To avoid checking between new mounts and clone mounts, I
instead pass both structures to a new function in super.c that finds the
cache key and then looks up the super cookie.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
This patch splits out the NFS v4 specific functionality of
nfs4_get_root() into its own rpc_op called by the generic client, and
leaves nfs4_proc_get_rootfh() as its own stand alone function. This
also allows me to change nfs4_remote_mount(), nfs4_xdev_mount() and
nfs4_remote_referral_mount() to use the generic client's nfs_get_root()
function. Later patches in this series will collapse these functions
into one common function, so using the same get_root() function
everywhere simplifies future changes.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
This function is really getting the root filehandle and not the root
dentry of the filesystem. I also removed the rpc_ops lookup from
nfs4_get_rootfh() under the assumption that if we reach this function
then we already know we are using NFS v4.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
When checking capabilities, the question we want to be asking is "does
current() have the capability in the child's namespace?"
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
The pathname of /usr/sbin/tomoyo-editpolicy seen from Ubuntu 12.04 Live CD is
squashfs:/usr/sbin/tomoyo-editpolicy rather than /usr/sbin/tomoyo-editpolicy .
Therefore, we need to accept manager programs which do not start with / .
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
Upon resume from standby, there is a possible interrupt
unsafe locking scenario raised when configure the Kernel
with CONFIG_PROVE_LOCKING. So this patch fixes that in
PM driver stuff by calling lock/unlock_irqsave/restore.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In mixed burst (MB) mode, the AHB master always initiates
the bursts with fixed-size when the DMA requests transfers
of size less than or equal to 16 beats.
This patch adds the MB support and the flag that can be
passed from the platform to select it.
MB mode can also give some benefits in terms of performances
on some platforms.
v2: fixed Coding Style
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to extend the number of MAC address registers
for 16 to 32. In fact, other new 16 registers are available in new
chips and this can help on perfect filter mode for unicast.
This patch also fixes the perfect filtering mode by setting the
bit 31 in the MAC address registers.
v2: fixed Coding Style.
Signed-off-by: Gianni Antoniazzi <gianni.antoniazzi-ext@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
wl_device_dealloc() dereferences the "dev" paramter, so let's move it
under the check for NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some coldfire boards (ie m5253demo) have a dm9000 onboard.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
David pointed out gcc might generate poor code with 31bit fields.
Using u16 is more than enough and permits a better code output.
Also make the code intent more readable using constants, fixed point arithmetic
not being trivial for everybody.
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Included changes:
* an improvement to avoid to linearise the whole received packet when not needed
* an improvement for client traffic rerouting after roaming
* a fix for the local translation table state-machine
* minor cleanups and fixes
|
|
This patch addresses a bug in a special case for target core SPC-2 RELEASE
logic where the same physical client (eg: iSCSI InitiatorName) with
differing iSCSI session identifiers (ISID) is allowed to incorrectly release
the same client's SPC-2 reservation from the non reservation holding path.
Note this bug is specific to iscsi-target w/ SPC-2 reservations, and
with the default enforce_pr_isids=1 device attr setting in target-core
controls if a InitiatorName + different ISID reservations are handled
the same as a single iSCSI client entity.
Signed-off-by: Bernhard Kohl <bernhard.kohl@gmx.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Section 15.3.1.2 of the software developer manual has this to say about the
RIPV bit in the IA32_MCG_STATUS register:
RIPV (restart IP valid) flag, bit 0 — Indicates (when set) that program
execution can be restarted reliably at the instruction pointed to by the
instruction pointer pushed on the stack when the machine-check exception
is generated. When clear, the program cannot be reliably restarted at
the pushed instruction pointer.
We need to save the state of this bit in do_machine_check() and use it
in mce_notify_process() to force a signal; even if memory_failure() says
it made a complete recovery ... e.g. replaced a clean LRU page.
Acked-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
active
worker_enter_idle() has WARN_ON_ONCE() which triggers if nr_running
isn't zero when every worker is idle. This can trigger spuriously
while a cpu is going down due to the way trustee sets %WORKER_ROGUE
and zaps nr_running.
It first sets %WORKER_ROGUE on all workers without updating
nr_running, releases gcwq->lock, schedules, regrabs gcwq->lock and
then zaps nr_running. If the last running worker enters idle
inbetween, it would see stale nr_running which hasn't been zapped yet
and trigger the WARN_ON_ONCE().
Fix it by performing the sanity check iff the trustee is idle.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next
|
|
Fix the following build error:
net/sched/sch_fq_codel.c: In function 'fq_codel_dump_stats':
net/sched/sch_fq_codel.c:464:3: error: unknown field 'qdisc_stats' specified in initializer
net/sched/sch_fq_codel.c:464:3: warning: missing braces around initializer
net/sched/sch_fq_codel.c:464:3: warning: (near initialization for 'st.<anonymous>')
net/sched/sch_fq_codel.c:465:3: error: unknown field 'qdisc_stats' specified in initializer
net/sched/sch_fq_codel.c:465:3: warning: excess elements in struct initializer
net/sched/sch_fq_codel.c:465:3: warning: (near initialization for 'st')
net/sched/sch_fq_codel.c:466:3: error: unknown field 'qdisc_stats' specified in initializer
net/sched/sch_fq_codel.c:466:3: warning: excess elements in struct initializer
net/sched/sch_fq_codel.c:466:3: warning: (near initialization for 'st')
net/sched/sch_fq_codel.c:467:3: error: unknown field 'qdisc_stats' specified in initializer
net/sched/sch_fq_codel.c:467:3: warning: excess elements in struct initializer
net/sched/sch_fq_codel.c:467:3: warning: (near initialization for 'st')
make[1]: *** [net/sched/sch_fq_codel.o] Error 1
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
m68k allmodconfig:
net/sched/sch_codel.c: In function ‘dequeue’:
net/sched/sch_codel.c:70: error: implicit declaration of function ‘prefetch’
make[1]: *** [net/sched/sch_codel.o] Error 1
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* renesas-kzm9g:
ARM: mach-shmobile: Use DT_MACHINE for KZM9G
|
|
* renesas-armadillo800eva:
ARM: mach-shmobile: Use DT_MACHINE for armadillo 800 eva
|
|
Reported-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|