| Age | Commit message (Collapse) | Author |
|---|
|
This patch fixes a null pointer dereference BUG() if ethtool is used on
an smsc9420 interface while it is down, because the phy_dev is only
allocated while the interface is up.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The newer chipsets (all PCI-E) are known that they need full power cycle
(AC or battery removal) to reset MAC address to a hardwired one. Previous
patch to address this problem loads the original MAC address from EEPROM.
But it brought other problem for which it is necessary to introduce a new
module parameter.
However, it might suffice to restore the initial MAC address before
shutdown/reboot/kexec and when removing the module.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NULL ptr OOPS
ipv4 ip_frag_reasm(), fully replace 'dev_net(dev)' with 'net', defined
previously patched into 2.6.29.
Between 2.6.28.10 and 2.6.29, net/ipv4/ip_fragment.c was patched,
changing from dev_net(dev) to container_of(...). Unfortunately the goto
section (out_fail) on oversized packets inside ip_frag_reasm() didn't
get touched up as well. Oversized IP packets cause a NULL pointer
dereference and immediate hang.
I discovered this running openvasd and my previous email on this is
titled: NULL pointer dereference at 2.6.32-rc8:net/ipv4/ip_fragment.c:566
Signed-off-by: David Ford <david@blue-labs.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pci_alloc_consistent uses GFP_ATOMIC allocation that may fail on some systems
with limited memory (Bug #14265). pci_pool_alloc allows waiting with
GFP_KERNEL.
Tested-by: Karol Lewandowski <karol.k.lewandowski@gmail.com>
Signed-off-by: Roger Oksanen <roger.oksanen@cs.helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch (as1305) fixes a bug in the irq-enable settings and removes
some related overhead in the runtime PM code.
In __pm_runtime_resume(), within the scope of the original
spin_lock_irq(), we know that irqs are disabled. There's no
reason to go through a pair of enable/disable cycles when
acquiring and releasing the parent's lock.
In __pm_runtime_set_status(), irqs are already disabled when
the parent's lock is acquired, and they must remain disabled
when it is released.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
When retransmitting due to T3 timeout, retransmit all the
in-flight chunks for the corresponding transport/path, including
chunks sent less then 1 rto ago.
This is the correct behaviour according to rfc4960 section 6.3.3
E3 and
"Note: Any DATA chunks that were sent to the address for which the
T3-rtx timer expired but did not fit in one MTU (rule E3 above)
should be marked for retransmission and sent as soon as cwnd
allows (normally, when a SACK arrives). ".
This fixes problems when more then one path is present and the T3
retransmission of the first chunk that timeouts stops the T3 timer
for the initial active path, leaving all the other in-flight
chunks waiting forever or until a new chunk is transmitted on the
same path and timeouts (and this will happen only if the cwnd
allows sending new chunks, but since cwnd was dropped to MTU by
the timeout => it will wait until the first heartbeat).
Example: 10 packets in flight, sent at 0.1 s intervals on the
primary path. The primary path is down and the first packet
timeouts. The first packet is retransmitted on another path, the
T3 timer for the primary path is stopped and cwnd is set to MTU.
All the other 9 in-flight packets will not be retransmitted
(unless more new packets are sent on the primary path which depend
on cwnd allowing it, and even in this case the 9 packets will be
retransmitted only after a new packet timeouts which even in the
best case would be more then RTO).
This commit reverts d0ce92910bc04e107b2f3f2048f07e94f570035d and
also removes the now unused transport->last_rto, introduced in
b6157d8e03e1e780660a328f7183bcbfa4a93a19.
p.s The problem is not only when multiple paths are there. It
can happen in a single homed environment. If the application
stops sending data, it possible to have a hung association.
Signed-off-by: Andrei Pelinescu-Onciul <andrei@iptel.org>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of the irq_req_t typedef'd struct can be re-worked quite
easily:
(1) IRQInfo2 was unused in any case, so drop it.
(2) IRQInfo1 was used write-only, so drop it.
(3) Instance (private data to be passed to the IRQ handler):
Most PCMCIA drivers using pcmcia_request_irq() to actually
register an IRQ handler set the "dev_id" to the same pointer
as the "priv" pointer in struct pcmcia_device. Modify the two
exceptions (ipwireless, ibmtr_cs) to also work this waym and
set the IRQ handler's "dev_id" to p_dev->priv unconditionally.
(4) Handler is to be of type irq_handler_t.
(5) Handler != NULL already tells whether an IRQ handler is present.
Therefore, we do not need the IRQ_HANDLER_PRESENT flag in
irq_req_t.Attributes.
CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-scsi@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: Jaroslav Kysela <perex@perex.cz>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Karsten Keil <isdn@linux-pingi.de>
for the Bluetooth parts: Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Update remaining users and remove deprecated handle_to_dev() macro
CC: Harald Welte <laforge@gnumonks.org>
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-serial@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
pcmcia_request_window() only needs a pointer to struct pcmcia_device, not
a pointer to a pointer.
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-scsi@vger.kernel.org
CC: Jiri Kosina <jkosina@suse.cz>
Acked-by: Karsten Keil <keil@b1-systems.de> (for ISDN)
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
pcmcia_get_window() and pcmcia_get_mem_page() were only called from
pcmcia_ioctl.c. Therefore, move these functions to that file, and
remove the useless EXPORTs.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Logic changes based on top of the other patches:
This set of patches changed window_handle_t from being a pointer to an
unsigned long. The unsigned long is now a simple index into socket->win[].
Going from a pointer to unsigned long should leave the user space interface
unchanged unless I'm mistaken.
This change results in code that is less error prone and a user space
interface which is much cleaner and safer. A nice side effect is that we
are also are able to remove all members except one from window_t.
[ linux@dominikbrodowski.net:
Update to 2.6.31. Also, a plain "index" to socket->win[] does not
work, as several codepaths rely on "window_handle_t" being
non-zero if used. Therefore, set the window_handle_t to the
socket->win[] index + 1. ]
CC: netdev@vger.kernel.org
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
No logic changes, just pass struct pcmcia_socket to pcmcia_get_mem_page()
[linux@dominikbrodowski.net: update to 2.6.31]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
No logic changes, just pass struct pcmcia_device to pcmcia_map_mem_page()
[linux@dominikbrodowski.net: update to 2.6.31]
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-scsi@vger.kernel.org
CC: Jiri Kosina <jkosina@suse.cz>
Acked-by: Karsten Keil <keil@b1-systems.de> (for ISDN)
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
No logic changes, just pass struct pcmcia_device to pcmcia_release_window().
[linux@dominikbrodowski.net: update to 2.6.31]
CC: netdev@vger.kernel.org
CC: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
To capture the relevant events for a given Perl script and to
avoid having to continually remember and type in long
command-lines, add a scripts/perl/bin directory containing two
simple shell scripts for each Perl script, one for recording and
one for processing/display. For example, to record perf data for
the rw-by-pid.pl script, run scripts/perl/bin/rw-by-pid-record
and to actually run the script and display the output run
scripts/perl/bin/rw-by-pid-report.
Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Cc: fweisbec@gmail.com
Cc: rostedt@goodmis.org
Cc: anton@samba.org
Cc: hch@infradead.org
LKML-Reference: <1259133352-23685-8-git-send-email-tzanussi@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Adds perf-trace-perl Documentation and a link to it from the
perf-trace page.
Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Cc: fweisbec@gmail.com
Cc: rostedt@goodmis.org
Cc: anton@samba.org
Cc: hch@infradead.org
LKML-Reference: <1259133352-23685-7-git-send-email-tzanussi@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The Perl scripting support for perf trace allows most of a trace
event's data to be accessed directly as handler arguments, but
not all of it e.g. the less common fields aren't passed in. To
give scripts access to the other fields and/or any other data or
metadata in the main perf executable that might be useful, a way
to access the C data in perf from Perl is needed; this patch
uses the Perl XS facility to do it for the common_xxx event
fields not passed to handler functions.
Context.pm exports three functions to Perl scripts that access
fields for the current event by calling back into perf:
common_pc(), common_flags() and common_lock_depth(). Support
for common_flags() field values was added to Core.pm and a
script used to sanity check these and other basic scripting
features, check-perf-trace.pl, was also added.
Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Cc: fweisbec@gmail.com
Cc: rostedt@goodmis.org
Cc: anton@samba.org
Cc: hch@infradead.org
LKML-Reference: <1259133352-23685-6-git-send-email-tzanussi@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Add Perf-Trace-Util Perl module and some scripts that use it.
Core.pm contains Perl code to define and access flag and
symbolic fields. Util.pm contains general-purpose utility
functions.
Also adds some makefile bits to install them in
libexec/perf-core/scripts/perl (or wherever perfexec_instdir
points).
Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Cc: fweisbec@gmail.com
Cc: rostedt@goodmis.org
Cc: anton@samba.org
Cc: hch@infradead.org
LKML-Reference: <1259133352-23685-5-git-send-email-tzanussi@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Implement trace_scripting_ops to make Perl a supported perf
trace scripting language.
Additionally adds code that allows Perl trace scripts to access
the 'flag' and 'symbolic' (__print_flags(), __print_symbolic())
field information parsed from the trace format files.
Also adds the Perl implementation of the generate_script()
trace_scripting_op, which creates a ready-to-run perf trace Perl
script based on existing trace data. Scripts generated by this
implementation print out all the fields for each event mentioned
in perf.data (and will detect and generate the proper scripting
code for 'flag' and 'symbolic' fields), and will additionally
generate handlers for the special 'trace_unhandled',
'trace_begin' and 'trace_end' handlers. Script authors can
simply remove the printing code to implement their own custom
event handling.
Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Cc: fweisbec@gmail.com
Cc: rostedt@goodmis.org
Cc: anton@samba.org
Cc: hch@infradead.org
LKML-Reference: <1259133352-23685-4-git-send-email-tzanussi@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
It's useful to know whether a field is a flag or symbolic field
for e.g. when generating scripts - it allows us to translate
those fields specially rather than literally as plain numeric
values.
Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Cc: fweisbec@gmail.com
Cc: rostedt@goodmis.org
Cc: anton@samba.org
Cc: hch@infradead.org
LKML-Reference: <1259133352-23685-3-git-send-email-tzanussi@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Adds an interface, scripting_ops, that when implemented for a
particular scripting language enables built-in support for trace
stream processing using that language.
The interface is designed to enable full-fledged language
interpreters to be embedded inside the perf executable and
thereby make the full capabilities of the supported languages
available for trace processing.
See below for details on the interface.
This patch also adds a couple command-line options to 'perf
trace':
The -s option option is used to specify the script to be run.
Script names that can be used with -s take the form:
[language spec:]scriptname[.ext]
Scripting languages register a set of 'language specs' that can
be used to specify scripts for the registered languages. The
specs can be used either as prefixes or extensions.
If [language spec:] is used, the script is taken as a script of
the matching language regardless of any extension it might have.
If [language spec:] is not used, [.ext] is used to look up the
language it corresponds to. Language specs are case
insensitive.
e.g. Perl scripts can be specified in the following ways:
Perl:scriptname
pl:scriptname.py # extension ignored
PL:scriptname
scriptname.pl
scriptname.perl
The -g [language spec] option gives users an easy starting point
for writing scripts in the specified language. Scripting
support for a particular language can implement a
generate_script() scripting op that outputs an empty (or
near-empty) set of handlers for all the events contained in a
given perf.data trace file - this option gives users a direct
way to access that.
Adding support for a scripting language
---------------------------------------
The main thing that needs to be done do add support for a new
language is to implement the scripting_ops interface:
It consists of the following four functions:
start_script()
stop_script()
process_event()
generate_script()
start_script() is called before any events are processed, and is
meant to give the scripting language support an opportunity to
set things up to receive events e.g. create and initialize an
instance of a language interpreter.
stop_script() is called after all events are processed, and is
meant to give the scripting language support an opportunity to
clean up e.g. destroy the interpreter instance, etc.
process_event() is called once for each event and takes as its
main parameter a pointer to the binary trace event record to be
processed. The implementation is responsible for picking out the
binary fields from the event record and sending them to the
script handler function associated with that event e.g. a
function derived from the event name it's meant to handle e.g.
'sched::sched_switch()'. The 'format' information for trace
events can be used to parse the binary data and map it into a
form usable by a given scripting language; see the Perl
implemention in subsequent patches for one possible way to
leverage the existing trace format parsing code in perf and map
that info into specific scripting language types.
generate_script() should generate a ready-to-run script for the
current set of events in the trace, preferably with bodies that
print out every field for each event. Again, look at the Perl
implementation for clues as to how that can be done. This is an
optional, but very useful op.
Support for a given language should also add a language-specific
setup function and call it from setup_scripting(). The
language-specific setup function associates the the scripting
ops for that language with one or more 'language specifiers'
(see below) using script_spec_register(). When a script name is
specified on the command line, the scripting ops associated with
the specified language are used to instantiate and use the
appropriate interpreter to process the trace stream.
In general, it should be relatively easy to add support for a
new language, especially if the language implementation supports
an interface allowing an interpreter to be 'embedded' inside
another program (in this case the containing program will be
'perf trace'). If so, it should be relatively straightforward to
translate trace events into invocations of user-defined script
functions where e.g. the function name corresponds to the event
type and the function parameters correspond to the event fields.
The event and field type information exported by the event
tracing infrastructure (via the event 'format' files) should be
enough to parse and send any piece of trace data to the user
script. The easiest way to see how this can be done would be to
look at the Perl implementation contained in
perf/util/trace-event-perl.c/.h.
There are a couple of other things that aren't covered by the
scripting_ops or setup interface and are technically optional,
but should be implemented if possible. One of these is support
for 'flag' and 'symbolic' fields e.g. being able to use more
human-readable values such as 'GFP_KERNEL' or
HI/BLOCK_IOPOLL/TASKLET in place of raw flag values. See the
Perl implementation to see how this can be done. The other thing
is support for 'calling back' into the perf executable to access
e.g. uncommon fields not passed by default into handler
functions, or any metadata the implementation might want to make
available to users via the language interface. Again, see the
Perl implementation for examples.
Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Cc: fweisbec@gmail.com
Cc: rostedt@goodmis.org
Cc: anton@samba.org
Cc: hch@infradead.org
LKML-Reference: <1259133352-23685-2-git-send-email-tzanussi@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Edwin Török found the following:
In function ‘memset’,
inlined from ‘ir_input_init’ at drivers/media/common/ir-functions.c:67:
/home/edwin/builds/linux-2.6/arch/x86/include/asm/string_64.h:61:
warning: call to ‘__warn_memset_zero_len’ declared with attribute
warning: memset used with constant zero length parameter; this could be
due to transposed parameters
memset(ir->ir_codes, sizeof(ir->ir_codes), 0);
In actual practice the only caller I can find happens to already have cleared
the buffer before calling ir_input_init.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Trivial fix for this compile warning:
v4l/sh_mobile_ceu_camera.c:1789: warning: label 'exit_free_irq' defined but not used
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
(rev 1)
Address yet another regression introduced by the introduction of the zl10353
disable_i2c_gate field.
djh - I unmangled the patch which apparently got screwed up in the user's
email client.
Signed-off-by: Robert Lowery <rglowery@exemail.com.au>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
When building for Sun 3:
drivers/built-in.o: In function `smscore_unregister_device':
drivers/media/dvb/siano/smscoreapi.c:723: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `smscore_register_device':
drivers/media/dvb/siano/smscoreapi.c:365: undefined reference to `dma_alloc_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Now we have a very high level routine for simple tools to
process IP sample events:
int event__preprocess_sample(const event_t *self,
struct addr_location *al,
symbol_filter_t filter)
It receives the event itself and will insert new threads in the
global threads list and resolve the map and symbol, filling all
this info into the new addr_location struct, so that tools like
annotate and report can further process the event by creating
hist_entries in their specific way (with or without callgraphs,
etc).
It in turn uses the new next layer function:
void thread__find_addr_location(struct thread *self, u8 cpumode,
enum map_type type, u64 addr,
struct addr_location *al,
symbol_filter_t filter)
This one will, given a thread (userspace or the kernel kthread
one), will find the given type (MAP__FUNCTION now, MAP__VARIABLE
too in the near future) at the given cpumode, taking vdsos into
account (userspace hit, but kernel symbol) and will fill all
these details in the addr_location given.
Tools that need a more compact API for plain function
resolution, like 'kmem', can use this other one:
struct symbol *thread__find_function(struct thread *self, u64 addr,
symbol_filter_t filter)
So, to resolve a kernel symbol, that is all the 'kmem' tool
needs, its just a matter of calling:
sym = thread__find_function(kthread, addr, NULL);
The 'filter' parameter is needed because we do lazy
parsing/loading of ELF symtabs or /proc/kallsyms.
With this we remove more code duplication all around, which is
always good, huh? :-)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: John Kacur <jkacur@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1259346563-12568-12-git-send-email-acme@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
While implementing event__preprocess_sample, that will do all of
the symbol lookup in one convenient function, I noticed that
util/process_event.[ch] were not being used at all, then started
looking if there were other functions that could be shared
and...
All those functions really don't need to receive offset + head,
the only thing they did was common to all of them, so do it at
one place instead.
Stats about number of each type of event processed now is done
in a central place.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: John Kacur <jkacur@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1259346563-12568-11-git-send-email-acme@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1259346563-12568-10-git-send-email-acme@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Making the routines that were so far specific to the kernel maps
useful for all threads.
This is done by making the kernel maps be contained in a kernel
"thread".
This gets the kernel specific routines closer to the userspace
counterparts, which will help in reducing the boilerplate for
resolving a symbol, as will be demonstrated in the next patches.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1259346563-12568-9-git-send-email-acme@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
So that we can support multiple symbol table types.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1259346563-12568-8-git-send-email-acme@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
So that the kallsyms loading routines are the direct counterpart
of the vmlinux loading ones, i.e. dso__load_kallsyms is the
counterpart of dso__load_vmlinux.
In the process make them also use the symbols rb tree indexed by
map->type, paving the way for supporting other types of symtabs,
such as the next one to be supported: variables.
This also allowed removal of yet another global variable:
kernel_map__functions.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1259346563-12568-7-git-send-email-acme@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
By using an array of rb_roots in struct dso we can, from a
struct map instance to get the right symbol rb_tree more easily.
This way we can have just one symbol lookup method for struct
map instances, map__find_symbol, instead of one per symtab type
(functions, variables).
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1259346563-12568-6-git-send-email-acme@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
That way we will be able to check if the right symtab is loaded
in the underlying DSO.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1259346563-12568-5-git-send-email-acme@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
perf annotate was the only user, and it doesn't really need it.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1259346563-12568-4-git-send-email-acme@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
We don't need to look at modules in dsos__findnew because the
kernel events come only with user DSOs. Also we need a way to
list just the module DSOs so that we can create multiple sets of
maps, now that we will support maps for the variables in a
symtab.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1259346563-12568-3-git-send-email-acme@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
As we'll have kernel_map[s]__variables too.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1259346563-12568-2-git-send-email-acme@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This should be properly fixed when we remove the XXX comment in
'perf report', function resolve_symbol.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1259346563-12568-1-git-send-email-acme@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This patch fixes two issues:
a) Infinite loop in resume function
b) Writes to non-existing registers in resume function
Cc: stable@kernel.org
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The comment in fuse_open about O_DIRECT:
"VFS checks this, but only _after_ ->open()"
also holds for fuse_create, however, the same kind of check was missing there.
As an impact of this bug, open(newfile, O_RDWR|O_CREAT|O_DIRECT) fails, but a
stub newfile will remain if the fuse server handled the implied FUSE_CREATE
request appropriately.
Other impact: in the above situation ima_file_free() will complain to open/free
imbalance if CONFIG_IMA is set.
Signed-off-by: Csaba Henk <csaba@gluster.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Harshavardhana <harsha@gluster.com>
Cc: stable@kernel.org
|
|
|
|
The data that was stored in this table is now available in
dev->archdata.iommu. So this table is not longer necessary.
This patch removes the remaining uses of that variable and
removes it from the code.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This patch removes the ugly contruct where the
iommu->lock must be released while before calling the
reset_iommu_command_buffer function.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This patch cleans up the code to flush device table entries
in the IOMMU. With this chance the driver can get rid of the
iommu_queue_inv_dev_entry() function.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This patch adds a function to flush a DTE entry for a given
struct device and replaces iommu_queue_inv_dev_entry calls
with this function where appropriate.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This patch cleans up the attach_device and detach_device
paths and fixes reference counting while at it.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This patch introduces a list to each protection domain which
keeps all devices associated with the domain. This can be
used later to optimize certain functions and to completly
remove the amd_iommu_pd_table.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This patch adds a reference count to each device to count
how often the device was bound to that domain. This is
important for single devices that act as an alias for a
number of others. These devices must stay bound to their
domains until all devices that alias to it are unbound from
the same domain.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This patch changes IOMMU code to use dev->archdata->iommu to
store information about the alias device and the domain the
device is attached to.
This allows the driver to get rid of the amd_iommu_pd_table
in the future.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
