| Age | Commit message (Collapse) | Author |
|---|
|
Replace pci_enable_device() with pcim_enable_device(),
pci_disable_device() and pci_release_regions() will be
called in release automatically.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The logic for discerning between KSZ8051 and KSZ87XX PHYs is incorrect
such that the that KSZ87XX switch is not identified correctly.
ksz8051_ksz8795_match_phy_device() uses the parameter ksz_phy_id
to discriminate whether it was called from ksz8051_match_phy_device()
or from ksz8795_match_phy_device() but since PHY_ID_KSZ87XX is the
same value as PHY_ID_KSZ8051, this doesn't work.
Instead use a bool to discriminate the caller.
Without this patch, the KSZ8795 switch port identifies as:
ksz8795-switch spi3.1 ade1 (uninitialized): PHY [dsa-0.1:03] driver [Generic PHY]
With the patch, it identifies correctly:
ksz8795-switch spi3.1 ade1 (uninitialized): PHY [dsa-0.1:03] driver [Micrel KSZ87XX Switch]
Fixes: 8b95599c55ed24b36cf4 ("net: phy: micrel: Discern KSZ8051 and KSZ8795 PHYs")
Signed-off-by: Steve Bennett <steveb@workware.net.au>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It should not return 0 when SID 0 is assigned to isids.
This patch fixes it.
Cc: stable@vger.kernel.org
Fixes: e3e0b582c321a ("selinux: remove unused initial SIDs and improve handling")
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
[PM: remove changelog from description]
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Vladimir Oltean says:
====================
FDB fixes for NXP SJA1105
I have some upcoming patches that make heavy use of statically installed
FDB entries, and when testing them on SJA1105P/Q/R/S and SJA1110, it
became clear that these switches do not behave reliably at all.
- On SJA1110, a static FDB entry cannot be installed at all
- On SJA1105P/Q/R/S, it is very picky about the inner/outer VLAN type
- Dynamically learned entries will make us not install static ones, or
even if we do, they might not take effect
Patch 5/6 has a conflict with net-next (sorry), the commit message of
that patch describes how to deal with it. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On SJA1105P/Q/R/S and SJA1110, the L2 Lookup Table entries contain a
maskable "inner/outer tag" bit which means:
- when set to 1: match single-outer and double tagged frames
- when set to 0: match untagged and single-inner tagged frames
- when masked off: match all frames regardless of the type of tag
This driver does not make any meaningful distinction between inner tags
(matches on TPID) and outer tags (matches on TPID2). In fact, all VLAN
table entries are installed as SJA1110_VLAN_D_TAG, which means that they
match on both inner and outer tags.
So it does not make sense that we install FDB entries with the IOTAG bit
set to 1.
In VLAN-unaware mode, we set both TPID and TPID2 to 0xdadb, so the
switch will see frames as outer-tagged or double-tagged (never inner).
So the FDB entries will match if IOTAG is set to 1.
In VLAN-aware mode, we set TPID to 0x8100 and TPID2 to 0x88a8. So the
switch will see untagged and 802.1Q-tagged packets as inner-tagged, and
802.1ad-tagged packets as outer-tagged. So untagged and 802.1Q-tagged
packets will not match FDB entries if IOTAG is set to 1, but 802.1ad
tagged packets will. Strange.
To fix this, simply mask off the IOTAG bit from FDB entries, and make
them match regardless of whether the VLAN tag is inner or outer.
Fixes: 1da73821343c ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar but not quite the same with what was done in commit b11f0a4c0c81
("net: dsa: sja1105: be stateless when installing FDB entries") for
SJA1105E/T, it is desirable to drop the priv->vlan_aware check and
simply go ahead and install FDB entries in the VLAN that was given by
the bridge.
As opposed to SJA1105E/T, in SJA1105P/Q/R/S and SJA1110, the FDB is a
maskable TCAM, and we are installing VLAN-unaware FDB entries with the
VLAN ID masked off. However, such FDB entries might completely obscure
VLAN-aware entries where the VLAN ID is included in the search mask,
because the switch looks up the FDB from left to right and picks the
first entry which results in a masked match. So it depends on whether
the bridge installs first the VLAN-unaware or the VLAN-aware FDB entries.
Anyway, if we had a VLAN-unaware FDB entry towards one set of DESTPORTS
and a VLAN-aware one towards other set of DESTPORTS, the result is that
the packets in VLAN-aware mode will be forwarded towards the DESTPORTS
specified by the VLAN-unaware entry.
To solve this, simply do not use the masked matching ability of the FDB
for VLAN ID, and always match precisely on it. In VLAN-unaware mode, we
configure the switch for shared VLAN learning, so the VLAN ID will be
ignored anyway during lookup, so it is redundant to mask it off in the
TCAM.
This patch conflicts with net-next commit 0fac6aa098ed ("net: dsa: sja1105:
delete the best_effort_vlan_filtering mode") which changed this line:
if (priv->vlan_state != SJA1105_VLAN_UNAWARE) {
into:
if (priv->vlan_aware) {
When merging with net-next, the lines added by this patch should take
precedence in the conflict resolution (i.e. the "if" condition should be
deleted in both cases).
Fixes: 1da73821343c ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
new address
Currently, when sja1105pqrs_fdb_add() is called for a host-joined IPv6
MDB entry such as 33:33:00:00:00:6a, the search for that address will
return the FDB entry for SJA1105_UNKNOWN_MULTICAST, which has a
destination MAC of 01:00:00:00:00:00 and a mask of 01:00:00:00:00:00.
It returns that entry because, well, it matches, in the sense that
unknown multicast is supposed by design to match it...
But the issue is that we then proceed to overwrite this entry with the
one for our precise host-joined multicast address, and the unknown
multicast entry is no longer there - unknown multicast is now flooded to
the same group of ports as broadcast, which does not look up the FDB.
To solve this problem, we should ignore searches that return the unknown
multicast address as the match, and treat them as "no match" which will
result in the entry being installed to hardware.
For this to work properly, we need to put the result of the FDB search
in a temporary variable in order to avoid overwriting the l2_lookup
entry we want to program. The l2_lookup entry returned by the search
might not have the same set of DESTPORTS and not even the same MACADDR
as the entry we're trying to add.
Fixes: 4d9423549501 ("net: dsa: sja1105: offload bridge port flags to device")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
statically added ones
The procedure to add a static FDB entry in sja1105 is concurrent with
dynamic learning performed on all bridge ports and the CPU port.
The switch looks up the FDB from left to right, and also learns
dynamically from left to right, so it is possible that between the
moment when we pick up a free slot to install an FDB entry, another slot
to the left of that one becomes free due to an address ageing out, and
that other slot is then immediately used by the switch to learn
dynamically the same address as we're trying to add statically.
The result is that we succeeded to add our static FDB entry, but it is
being shadowed by a dynamic FDB entry to its left, and the switch will
behave as if our static FDB entry did not exist.
We cannot really prevent this from happening unless we make the entire
process to add a static FDB entry a huge critical section where address
learning is temporarily disabled on _all_ ports, and then re-enabled
according to the configuration done by sja1105_port_set_learning.
However, that is kind of disruptive for the operation of the network.
What we can do alternatively is to simply read back the FDB for dynamic
entries located before our newly added static one, and delete them.
This will guarantee that our static FDB entry is now operational. It
will still not guarantee that there aren't dynamic FDB entries to the
_right_ of that static FDB entry, but at least those entries will age
out by themselves since they aren't hit, and won't bother anyone.
Fixes: 291d1e72b756 ("net: dsa: sja1105: Add support for FDB and MDB management")
Fixes: 1da73821343c ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
.port_fdb_add
The SJA1105 switch family leaves it up to software to decide where
within the FDB to install a static entry, and to concatenate destination
ports for already existing entries (the FDB is also used for multicast
entries), it is not as simple as just saying "please add this entry".
This means we first need to search for an existing FDB entry before
adding a new one. The driver currently manages to fool itself into
thinking that if an FDB entry already exists, there is nothing to be
done. But that FDB entry might be dynamically learned, case in which it
should be replaced with a static entry, but instead it is left alone.
This patch checks the LOCKEDS ("locked/static") bit from found FDB
entries, and lets the code "goto skip_finding_an_index;" if the FDB
entry was not static. So we also need to move the place where we set
LOCKEDS = true, to cover the new case where a dynamic FDB entry existed
but was dynamic.
Fixes: 291d1e72b756 ("net: dsa: sja1105: Add support for FDB and MDB management")
Fixes: 1da73821343c ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The blamed commit made FDB access on SJA1110 functional only as far as
dumping the existing entries goes, but anything having to do with an
entry's index (adding, deleting) is still broken.
There are in fact 2 problems, all caused by improperly inheriting the
code from SJA1105P/Q/R/S:
- An entry size is SJA1110_SIZE_L2_LOOKUP_ENTRY (24) bytes and not
SJA1105PQRS_SIZE_L2_LOOKUP_ENTRY (20) bytes
- The "index" field within an FDB entry is at bits 10:1 for SJA1110 and
not 15:6 as in SJA1105P/Q/R/S
This patch moves the packing function for the cmd->index outside of
sja1105pqrs_common_l2_lookup_cmd_packing() and into the device specific
functions sja1105pqrs_l2_lookup_cmd_packing and
sja1110_l2_lookup_cmd_packing.
Fixes: 74e7feff0e22 ("net: dsa: sja1105: fix dynamic access to L2 Address Lookup table for SJA1110")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/fixes
mvebu fixes for 5.14 (part 1)
- Fix i2c property for armada-3720-turris-mox in order to use SFP
- Add mmc alias on armada-3720-turris-mox to allow rootfs using the
right mmc
* tag 'mvebu-fixes-5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arm64: dts: armada-3720-turris-mox: remove mrvl,i2c-fast-mode
arm64: dts: armada-3720-turris-mox: fixed indices for the SDHC controllers
Link: https://lore.kernel.org/r/87k0l7zx4v.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/fixes
STM32 DT fixes for v5.14, round 1
Highlights:
-----------
-Fixes are for DHCOM/DHCOR boards:
- Set HW RTC ad default RTC
- Disable EDPD LAN8710 feature as it is not a stable feature.
- Fix touchscreen IRQ line assignment
* tag 'stm32-dt-for-v5.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: Fix touchscreen IRQ line assignment on DHCOM
ARM: dts: stm32: Disable LAN8710 EDPD on DHCOM
ARM: dts: stm32: Prefer HW RTC on DHCOM SoM
Link: https://lore.kernel.org/r/c0b6031b-2de7-2ef8-71b2-a0af8f475932@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.linaro.org:/people/jens.wiklander/linux-tee into arm/fixes
tee: Improve support for kexec and kdump
This fixes several bugs uncovered while exercising the OP-TEE, ftpm
(firmware TPM), and tee_bnxt_fw (Broadcom BNXT firmware manager) drivers
with kexec and kdump (emergency kexec) based workflows.
* tag 'tee-kexec-fixes-for-v5.14' of git://git.linaro.org:/people/jens.wiklander/linux-tee:
firmware: tee_bnxt: Release TEE shm, session, and context during kexec
tpm_ftpm_tee: Free and unregister TEE shared memory during kexec
tee: Correct inappropriate usage of TEE_SHM_DMA_BUF flag
tee: add tee_shm_alloc_kernel_buf()
optee: Clear stale cache entries during initialization
optee: fix tee out of memory failure seen during kexec reboot
optee: Refuse to load the driver under the kdump kernel
optee: Fix memory leak when failing to register shm pages
Link: https://lore.kernel.org/r/20210726081039.GA2482361@jade
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.14:
- A couple of fixes on MMDC driver to add missing iounmap() and
clk_disable_unprepare(), and a follow-up fix.
- Fix missing-prototypes warning in SRC driver.
- Revert commit 7d981405d0fd ("soc: imx8m: change to use platform
driver"), which breaks i.MX8M system that has CAAM driver enabled.
- One fix on imx53-m53menlo pinctrl configuration.
- Increase the PHY reset duration for imx6qdl-sr-som to fix intermittent
issues where the PHY would be unresponsive every once in a while.
- Add missing flag for in-band signalling between PHY and MAC on
kontron-sl28-var2 board to fix network support.
- Limit the SDIO Clock on Colibri iMX6ULL to 25MHz for fixing wireless
noise issue.
- Fix sysclk node name for LS1028A so that U-Boot is able to update the
"clock-frequency" property.
* tag 'imx-fixes-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx: Swap M53Menlo pinctrl_power_button/pinctrl_power_out pins
ARM: imx: fix missing 3rd argument in macro imx_mmdc_perf_init
ARM: dts: colibri-imx6ull: limit SDIO clock to 25MHz
arm64: dts: ls1028: sl28: fix networking for variant 2
Revert "soc: imx8m: change to use platform driver"
ARM: dts: imx6qdl-sr-som: Increase the PHY reset duration to 10ms
ARM: imx: common: Move prototype outside the SMP block
ARM: imx: add missing clk_disable_unprepare()
ARM: imx: add missing iounmap()
arm64: dts: ls1028a: fix node name for the sysclk
Link: https://lore.kernel.org/r/20210726023221.GF5901@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
When this driver is disabled, the board file fails to build,
so add a dependency:
arch/arm/mach-ixp4xx/goramo_mlr.c: In function 'gmlr_pci_preinit':
arch/arm/mach-ixp4xx/goramo_mlr.c:472:9: error: implicit declaration of function 'ixp4xx_pci_preinit'; did you mean 'iop3xx_pci_preinit'? [-Werror=implicit-function-declaration]
472 | ixp4xx_pci_preinit();
| ^~~~~~~~~~~~~~~~~~
| iop3xx_pci_preinit
arch/arm/mach-ixp4xx/goramo_mlr.c: In function 'gmlr_pci_postinit':
arch/arm/mach-ixp4xx/goramo_mlr.c:481:22: error: implicit declaration of function 'ixp4xx_pci_read' [-Werror=implicit-function-declaration]
481 | if (!ixp4xx_pci_read(addr, NP_CMD_CONFIGREAD, &value)) {
| ^~~~~~~~~~~~~~~
arch/arm/mach-ixp4xx/goramo_mlr.c:231:35: error: 'IXP4XX_UART1_BASE_PHYS' undeclared here (not in a function)
231 | .start = IXP4XX_UART1_BASE_PHYS,
| ^~~~~~~~~~~~~~~~~~~~~~
arch/arm/mach-ixp4xx/goramo_mlr.c: In function 'gmlr_init':
arch/arm/mach-ixp4xx/goramo_mlr.c:376:9: error: implicit declaration of function 'ixp4xx_sys_init' [-Werror=implicit-function-declaration]
376 | ixp4xx_sys_init();
| ^~~~~~~~~~~~~~~
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: soc@kernel.org
Link: https://lore.kernel.org/r/20210721151620.2373500-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Randconfig builds on the ixp4xx ethernet driver showed that the qmgr and
npe drivers are not actually built even when compile testing is enabled:
ERROR: modpost: "qmgr_stat_empty" [drivers/net/ethernet/xscale/ixp4xx_eth.ko] undefined!
ERROR: modpost: "qmgr_enable_irq" [drivers/net/ethernet/xscale/ixp4xx_eth.ko] undefined!
ERROR: modpost: "qmgr_set_irq" [drivers/net/ethernet/xscale/ixp4xx_eth.ko] undefined!
ERROR: modpost: "__qmgr_request_queue" [drivers/net/ethernet/xscale/ixp4xx_eth.ko] undefined!
ERROR: modpost: "npe_send_recv_message" [drivers/net/ethernet/xscale/ixp4xx_eth.ko] undefined!
ERROR: modpost: "npe_recv_message" [drivers/net/ethernet/xscale/ixp4xx_eth.ko] undefined!
ERROR: modpost: "npe_load_firmware" [drivers/net/ethernet/xscale/ixp4xx_eth.ko] undefined!
ERROR: modpost: "npe_running" [drivers/net/ethernet/xscale/ixp4xx_eth.ko] undefined!
ERROR: modpost: "qmgr_disable_irq" [drivers/net/ethernet/xscale/ixp4xx_eth.ko] undefined!
ERROR: modpost: "qmgr_stat_below_low_watermark" [drivers/net/ethernet/xscale/ixp4xx_eth.ko] undefined!
Fix it by always entering the drivers/soc/ixp4xx/ directory, and fix the
resulting compile test failures by removing the #include statements
that prevent building on most other platforms.
Fixes: 7a6c9dbb36a4 ("soc: ixp4xx: Protect IXP4xx SoC drivers by ARCH_IXP4XX || COMPILE_TEST")
Fixes: fcf2d8978cd5 ("ARM: ixp4xx: Move NPE and QMGR to drivers/soc")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210721211412.3537004-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The regulator coupler drivers now use regulator-driver API function that
isn't available during compile-testing. Make regulator coupler drivers
dependent on CONFIG_REGULATOR in Kconfig.
Fixes: 03978d42ed0d ("soc/tegra: regulators: Bump voltages on system reboot")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/fixes
arm64: tegra: Device tree fixes for v5.14-rc3
This contains one more fix for SMMU enablement on Tegra194, this time
for PCIe.
* tag 'tegra-for-5.14-rc3-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Enable SMMU support for PCIe on Tegra194
Link: https://lore.kernel.org/r/20210716233858.10096-1-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Once the new schema interrupt-controller/arm,vic.yaml is added, we get
the below warnings:
arch/arm/boot/dts/ste-nomadik-nhk15.dt.yaml:
intc@10140000: $nodename:0: 'intc@10140000' does not match
'^interrupt-controller(@[0-9a-f,]+)*$'
Fix the node names for the interrupt controller to conform
to the standard node name interrupt-controller@..
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210617210825.3064367-2-sudeep.holla@arm.com
Link: https://lore.kernel.org/r/20210626000103.830184-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch cleanups below cppcheck warning.
sound/soc/soc-topology.c:2129:27: style: The scope of the variable 'link' can be reduced. [variableScope]
struct snd_soc_dai_link *link;
^
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87mtq0wfkn.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch cleanups below cppcheck warning.
sound/soc/soc-topology.c:1038:31: style: The scope of the variable 'control_hdr' can be reduced. [variableScope]
struct snd_soc_tplg_ctl_hdr *control_hdr;
^
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o8agwfkv.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
soc_tplg_dapm_widget_elems_load()
This patch cleanups below cppcheck warning.
sound/soc/soc-topology.c:1599:35: style: The scope of the variable 'widget' can be reduced. [variableScope]
struct snd_soc_tplg_dapm_widget *widget;
^
sound/soc/soc-topology.c:1600:6: style: The scope of the variable 'ret' can be reduced. [variableScope]
int ret, count, i;
^
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87pmuwwfl7.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch cleanups below cppcheck warning.
sound/soc/soc-topology.c:2350:27: style: The scope of the variable 'dai' can be reduced. [variableScope]
struct snd_soc_tplg_dai *dai;
^
sound/soc/soc-topology.c:2352:9: style: The scope of the variable 'ret' can be reduced. [variableScope]
int i, ret;
^
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87r1fcwflh.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch cleanups below cppcheck warning.
sound/soc/soc-topology.c:2576:27: style: The scope of the variable 'hdr' can be reduced. [variableScope]
struct snd_soc_tplg_hdr *hdr;
^
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87sfzswflw.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 3a70dd2d0503 ("spi: mediatek: fix fifo rx mode") claims that
fifo RX mode was never handled, and adds the presumably missing code
to the FIFO transfer function. However, the claim that receive data
was not handled is incorrect. It was handled as part of interrupt
handling after the transfer was complete. The code added with the above
mentioned commit reads data from the receive FIFO before the transfer
is started, which is wrong. This results in an actual transfer error
on a Hayato Chromebook.
Remove the code trying to handle receive data before the transfer is
started to fix the problem.
Fixes: 3a70dd2d0503 ("spi: mediatek: fix fifo rx mode")
Cc: Peter Hess <peter.hess@ph-home.de>
Cc: Frank Wunderlich <frank-w@public-files.de>
Cc: Tzung-Bi Shih <tzungbi@google.com>
Cc: Hsin-Yi Wang <hsinyi@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Hsin-Yi Wang <hsinyi@google.com>
Tested-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20210802030023.1748777-1-linux@roeck-us.net
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Don't populate arrays on the stack but instead them static const.
Makes the object code smaller by 242 bytes.
Before:
text data bss dec hex filename
23827 8764 0 32591 7f4f ./sound/soc/sh/rcar/ssi.o
After:
text data bss dec hex filename
23361 8988 0 32349 7e5d ./sound/soc/sh/rcar/ssi.o
gcc version 10.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210801063237.137998-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
PCM buffers might be allocated dynamically when the buffer
preallocation failed or a larger buffer is requested, and it's not
guaranteed that substream->dma_buffer points to the actually used
buffer. The driver needs to refer to substream->runtime->dma_addr
instead for the buffer address.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20210731084331.32225-1-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 13511704f8d759 ("net: taprio offload: enforce qdisc to netdev queue mapping")
resulted in duplicate entries in the qdisc hash.
While this did not impact the overall operation of the qdisc and taprio
code paths, it did result in an infinite loop when dumping the qdisc
properties, at least on one target (NXP LS1028 ARDB).
Removing the duplicate call to qdisc_hash_add() solves the problem.
Fixes: 13511704f8d759 ("net: taprio offload: enforce qdisc to netdev queue mapping")
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The expression sizeof(**ptr) for the void **ptr is just 1 rather than
the size of a pointer. Fix this by using sizeof(*ptr).
Addresses-Coverity: ("Wrong sizeof argument")
Fixes: e145d9a184f2 ("interconnect: Add devm_of_icc_get() as exported API for users")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210730075408.19945-1-colin.king@canonical.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
GSO expects inner transport header offset to be valid when
skb->encapsulation flag is set. GSO uses this value to calculate the length
of an individual segment of a GSO packet in skb_gso_transport_seglen().
However, tcp/udp gro_complete callbacks don't update the
skb->inner_transport_header when processing an encapsulated TCP/UDP
segment. As a result a GRO skb has ->inner_transport_header set to a value
carried over from earlier skb processing.
This can have mild to tragic consequences. From miscalculating the GSO
segment length to triggering a page fault [1], when trying to read TCP/UDP
header at an address past the skb->data page.
The latter scenario leads to an oops report like so:
BUG: unable to handle page fault for address: ffff9fa7ec00d008
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 123f201067 P4D 123f201067 PUD 123f209067 PMD 0
Oops: 0000 [#1] SMP NOPTI
CPU: 44 PID: 0 Comm: swapper/44 Not tainted 5.4.53-cloudflare-2020.7.21 #1
Hardware name: HYVE EDGE-METAL-GEN10/HS-1811DLite1, BIOS V2.15 02/21/2020
RIP: 0010:skb_gso_transport_seglen+0x44/0xa0
Code: c0 41 83 e0 11 f6 87 81 00 00 00 20 74 30 0f b7 87 aa 00 00 00 0f [...]
RSP: 0018:ffffad8640bacbb8 EFLAGS: 00010202
RAX: 000000000000feda RBX: ffff9fcc8d31bc00 RCX: ffff9fa7ec00cffc
RDX: ffff9fa7ebffdec0 RSI: 000000000000feda RDI: 0000000000000122
RBP: 00000000000005c4 R08: 0000000000000001 R09: 0000000000000000
R10: ffff9fe588ae3800 R11: ffff9fe011fc92f0 R12: ffff9fcc8d31bc00
R13: ffff9fe0119d4300 R14: 00000000000005c4 R15: ffff9fba57d70900
FS: 0000000000000000(0000) GS:ffff9fe68df00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff9fa7ec00d008 CR3: 0000003e99b1c000 CR4: 0000000000340ee0
Call Trace:
<IRQ>
skb_gso_validate_network_len+0x11/0x70
__ip_finish_output+0x109/0x1c0
ip_sublist_rcv_finish+0x57/0x70
ip_sublist_rcv+0x2aa/0x2d0
? ip_rcv_finish_core.constprop.0+0x390/0x390
ip_list_rcv+0x12b/0x14f
__netif_receive_skb_list_core+0x2a9/0x2d0
netif_receive_skb_list_internal+0x1b5/0x2e0
napi_complete_done+0x93/0x140
veth_poll+0xc0/0x19f [veth]
? mlx5e_napi_poll+0x221/0x610 [mlx5_core]
net_rx_action+0x1f8/0x790
__do_softirq+0xe1/0x2bf
irq_exit+0x8e/0xc0
do_IRQ+0x58/0xe0
common_interrupt+0xf/0xf
</IRQ>
The bug can be observed in a simple setup where we send IP/GRE/IP/TCP
packets into a netns over a veth pair. Inside the netns, packets are
forwarded to dummy device:
trafgen -> [veth A]--[veth B] -forward-> [dummy]
For veth B to GRO aggregate packets on receive, it needs to have an XDP
program attached (for example, a trivial XDP_PASS). Additionally, for UDP,
we need to enable GSO_UDP_L4 feature on the device:
ip netns exec A ethtool -K AB rx-udp-gro-forwarding on
The last component is an artificial delay to increase the chances of GRO
batching happening:
ip netns exec A tc qdisc add dev AB root \
netem delay 200us slot 5ms 10ms packets 2 bytes 64k
With such a setup in place, the bug can be observed by tracing the skb
outer and inner offsets when GSO skb is transmitted from the dummy device:
tcp:
FUNC DEV SKB_LEN NH TH ENC INH ITH GSO_SIZE GSO_TYPE
ip_finish_output dumB 2830 270 290 1 294 254 1383 (tcpv4,gre,)
^^^
udp:
FUNC DEV SKB_LEN NH TH ENC INH ITH GSO_SIZE GSO_TYPE
ip_finish_output dumB 2818 270 290 1 294 254 1383 (gre,udp_l4,)
^^^
Fix it by updating the inner transport header offset in tcp/udp
gro_complete callbacks, similar to how {inet,ipv6}_gro_complete callbacks
update the inner network header offset, when skb->encapsulation flag is
set.
[1] https://lore.kernel.org/netdev/CAKxSbF01cLpZem2GFaUaifh0S-5WYViZemTicAg7FCHOnh6kug@mail.gmail.com/
Fixes: bf296b125b21 ("tcp: Add GRO support")
Fixes: f993bc25e519 ("net: core: handle encapsulation offloads when computing segment lengths")
Fixes: e20cf8d3f1f7 ("udp: implement GRO for plain UDP sockets.")
Reported-by: Alex Forster <aforster@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A crash has been observed if rmmod is done while automatic debug
collection in progress. It is due to a race condition between
both of them.
To fix stop the sp_task during unload to avoid running qede_sp_task
even if they are schedule during removal process.
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just briefly described about the new option.
Link: https://lore.kernel.org/r/20210729074404.19728-6-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch adds a new module option, quirk_flags, for allowing user to
try some additional device-specific quirk behavior more easily.
When this option is set to non-zero, it overrides the quirk_flags, and
the specific workaround is applied.
Link: https://lore.kernel.org/r/20210729074404.19728-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The generic DSD raw detection is based on the known allow list, and we
can integrate it into quirk_flags, too.
Link: https://lore.kernel.org/r/20210729074404.19728-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The mixer code has a flag ignore_ctl_error for ignoring the errors
returned from the device wrt mixer accesses, and this is set from the
entries in mixer_maps.c, as well as ignore_ctl_error module option.
Those can be well integrated into the new quirk_flags field, too.
Link: https://lore.kernel.org/r/20210729074404.19728-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The auto-suspend suppression workaround for Lenovo machines are
handled in quirks-table.h. Now it's more easier to handle with
quirk_flags.
Link: https://lore.kernel.org/r/20210729074404.19728-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The rate validation at the device probe is applied only to the
specific devices (currently only for MOTU devices), and this check can
be moved to quirk_flags gracefully, too.
Link: https://lore.kernel.org/r/20210729074404.19728-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Yet another delay is applied at switching the interface. This can be
moved to quirk_flags, too.
Link: https://lore.kernel.org/r/20210729073855.19043-10-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
We apply some delay for the control messages on certain devices as a
workaround, and this can be moved into the quirk_flags as well.
Currently there are three different delay periods (1ms, 5ms and 20ms),
so three different quirk bits are assigned for them.
Link: https://lore.kernel.org/r/20210729073855.19043-9-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The devices with ITF-USB DSD type are listed in another function, and
this can be integrated into the quirk_flags easily.
Link: https://lore.kernel.org/r/20210729073855.19043-8-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There are a couple of device-specific quirks in the clock setup code,
and those can be moved gracefully to quirk_flags, too.
Link: https://lore.kernel.org/r/20210729073855.19043-7-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The snd_usb_audio.playback_first flag is used by the implicit feedback
mode handling, and this can be also moved to quirk_flags.
Link: https://lore.kernel.org/r/20210729073855.19043-6-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There is another quirk for the transfer, and that's currently specific
to Zoom R16/24, handled in create_standard_audio_quirk(). Let's move
this also to the new quirk_flags.
Link: https://lore.kernel.org/r/20210729073855.19043-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The txfr_quirk field was meant for aligning the transfer, and it's set
for certain devices in quirks-table.h. Now we can move that stuff
also to the new quirk_flags gracefully, and reduce the quirks-table.h
entries (that are exposed to module device table).
As the quirks-table.h entries are also with the name string override,
provide the corresponding entries to the usb_audio_names[] table,
too.
Link: https://lore.kernel.org/r/20210729073855.19043-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The devices that can have media-controller API entries are currently
specified via tables in quirks-table.h, as a part of descriptor
override. This can fit better to the new quirk_flags, as we just need
a matching with the given ID and create the MC entries accordingly.
Link: https://lore.kernel.org/r/20210729073855.19043-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
As more and more device-specific workarounds came up and gathered in
various places, it becomes harder to manage. Now it's time to clean
up and collect workarounds more consistently and make them more easily
applicable.
This patch is the first step for that: a new field quirk_flags is
introduced in snd_usb_audio struct to contain the bit flags for
various device-specific quirks. Those are separate one from the
quirks in quirks-table.h; the quirks-table.h entries are for more
intrusive stuff that needs the descriptor override, while the new
quirk_flags is for easier ones that are tied with the vendor:product
IDs.
In this patch, as the first example, we convert the list of devices
and vendors to ignore GET_SAMPLE_RATE, formerly defined in
snb_usb_get_sample_rate_quirk().
Link: https://lore.kernel.org/r/20210729073855.19043-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
The recent code refactoring made the mmap of continuous pages to be
done via the own helper snd_dma_continuous_mmap() with
remap_pfn_range(). There I overlooked that dmab->addr isn't set for
the allocation with SNDRV_DMA_TYPE_CONTINUOUS. This resulted always
in an error at mmap with this buffer type on the system such as
Intel SST Baytrail driver.
This patch fixes the regression by passing the correct address.
Fixes: 30b7ba6972d5 ("ALSA: core: Add continuous and vmalloc mmap ops")
Reported-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/8d6674da-7d7b-803e-acc9-7de6cb1223fa@redhat.com
Link: https://lore.kernel.org/r/20210801113801.31290-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Commit dea7a9fbb009 ("dmaengine: imx-dma: remove dma_slave_config
direction usage") changes the method from a "configuration when called"
to an "configuration when used". Due to this, only the cyclic DMA type
gets configured correctly, while the generic DMA type is left
non-configured.
Without this additional call, the struct imxdma_channel::word_size member
is stuck at DMA_SLAVE_BUSWIDTH_UNDEFINED and imxdma_prep_slave_sg() always
returns NULL.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Fixes: dea7a9fbb009 ("dmaengine: imx-dma: remove dma_slave_config direction usage")
Link: https://lore.kernel.org/r/20210729071821.9857-1-jbe@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
