| Age | Commit message (Collapse) | Author |
|---|
|
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The auto-negotiation state in the PCS as set by
phylink_mii_c22_pcs_config was previously always enabled when the
driver is configured for in-band autonegotiation, even if
autonegotiation was disabled on the interface with ethtool. Update the
code to set the BMCR_ANENABLE bit based on the interface's
autonegotiation enabled state.
Update phylink_mii_c22_pcs_get_state to not check
autonegotiation-related fields when autonegotiation is disabled.
Update phylink_mac_pcs_get_state to initialize the state based on the
interface's configured speed, duplex and pause parameters rather than
to unknown when autonegotiation is disabled, before calling the
driver's pcs_get_state functions, as they are not likely to provide
meaningful data for these fields when autonegotiation is disabled. In
this case the driver is really just filling in the link state field.
Note that in cases where there is a downstream PHY connected, such as
with SGMII and a copper PHY, the configuration set by ethtool is
handled by phy_ethtool_ksettings_set and not propagated to the PCS.
This is correct since SGMII or 1000Base-X autonegotiation with the PCS
should normally still be used even if the copper side has disabled it.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eric reported that the rate estimator reads statics from the softirq
which in turn triggers a warning introduced in the statistics rework.
The warning is too cautious. The updates happen in the softirq context
so reads from softirq are fine since the writes can not be preempted.
The updates/writes happen during qdisc_run() which ensures one writer
and the softirq context.
The remaining bad context for reading statistics remains in hard-IRQ
because it may preempt a writer.
Fixes: 29cbcd8582837 ("net: sched: Remove Qdisc::running sequence counter")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit ea269a6f7207 ("net: phylink: Update SFP selected interface on
advertising changes") added a better solution to selecting the
interface mode for SFPs using the advertisement mask. This method will
work for mvneta and mvpp2 when selecting between 2500base-X and
1000base-X without needing to use the basex helper, or indicate that
we support both 1000base-X and 2500base-X when in either of these two
interface modes.
Hence, we need to eliminate the validation prior to selecting the
interface, otherwise when we clean up mvneta's validation function, we
will end up locking to 2500base-X as we validate with an interface mode
of PHY_INERFACE_MODE_2500BASEX.
The supported mask will already have been reduced down to the union of
support for the SFP and MAC already, so we can be confident that the
advertisement mask is already appropriately restricted. We only need to
select the appropriate interface, and then revalidate with the new
interface mode.
We get rid of the check for pl->sfp_port too, this is meaningless here
as it doesn't get cleared when a module is removed, so it doesn't
indicate if a module is present. Just rely on pl->sfp_bus.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This assignment statement is meaningless, because the statement
will execute to the tag "set_itr_now".
The clang_analyzer complains as follows:
drivers/net/ethernet/intel/e1000e/netdev.c:2552:3 warning:
Value stored to 'current_itr' is never read.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: luo penghao <luo.penghao@zte.com.cn>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jakub Kicinski says:
====================
ethernet: add eth_hw_addr_gen() for switches
While doing the last polishing of the drivers/ethernet
changes I realized we have a handful of drivers offsetting
some base MAC addr by an id. So I decided to add a helper
for it. The helper takes care of wrapping which is probably
not 100% necessary but seems like a good idea. And it saves
driver side LoC (the diffstat is actually negative if we
compare against the changes I'd have to make if I was to
convert all these drivers to not operate directly on
netdev->dev_addr).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Vadym and Taras report that the current behavior of the driver
is not exactly expected and it's better to add the port id in
like other drivers do.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have 5 drivers which offset base MAC addr by port id.
Create a helper for them.
This helper takes care of overflows, which some drivers
did not do, please complain if that's going to break
anything!
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Generalize the use of ndescs by adding it to mlx5_ib_mkey.
Signed-off-by: Aharon Landau <aharonl@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
Jakub Kicinski says:
====================
ethernet: manual netdev->dev_addr conversions (part 2)
Manual conversions of Ethernet drivers writing directly
to netdev->dev_addr (part 2 out of 3).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Break the address up into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Break the address up into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Invert the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move mlx5_core_mkey struct to mlx5_ib, as the mlx5_core doesn't use it
at this point.
Signed-off-by: Aharon Landau <aharonl@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
In mlx5_core and vdpa there is no use of mlx5_core_mkey members except
for the key itself.
As preparation for moving mlx5_core_mkey to mlx5_ib, the occurrences of
struct mlx5_core_mkey in all modules except for mlx5_ib are replaced by
a u32 key.
Signed-off-by: Aharon Landau <aharonl@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
There is no read of mkey->pd, only write. Remove it.
Signed-off-by: Aharon Landau <aharonl@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
mkey->size is already stored in ibmr->length, no need to store it here.
Signed-off-by: Aharon Landau <aharonl@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
iova is already stored in ibmr->iova, no need to store it here.
Signed-off-by: Aharon Landau <aharonl@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
Ido Schimmel says:
====================
mlxsw: Multi-level qdisc offload
Petr says:
Currently, mlxsw admits for offload a suitable root qdisc, and its
children. Thus up to two levels of hierarchy are offloaded. Often, this is
enough: one can configure TCs with RED and TCs with a shaper on, and can
even see counters for each TC by looking at a qdisc at a sufficiently
shallow position.
While simple, the system has obvious shortcomings. It is not possible to
configure both RED and shaping on one TC. It is not possible to place a
PRIO below root TBF, which would then be offloaded as port shaper. FIFOs
are only offloaded at root or directly below, which is confusing to users,
because RED and TBF of course have their own FIFO.
This patch set lifts assumptions that prevent offloading multi-level qdisc
trees.
In patch #1, offload of a graft operation is added to TBF. Grafts are
issued as another qdisc is linked to the qdisc in question, and give
drivers a chance to react to the linking. The absence of this event was not
a major issue so far, because TBF was not considered classful, which
changes with this patchset.
The codebase currently assumes that ETS and PRIO are the only classful
qdiscs. The following patches gradually lift this assumption.
In patch #2, calculation of traffic class and priomap of a qdisc is fixed.
Patch #3 fixes handling of future FIFOs. Child FIFO qdiscs may be created
and notified before their parent qdisc exists and therefore need special
handling.
Patches #4, #5 and #6 unify, respectively, child destruction, child
grafting, and cleanup of statistics.
Patch #7 adds a function that validates whether a given qdisc topology is
offloadable.
Finally in patch #8, TBF and RED become classful. At this point, FIFO
qdiscs grafted to an offloaded qdisc should always be offloaded.
Patch #9 adds a selftest to verify some offloadable and unoffloadable qdisc
trees.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This checks that various qdisc configurations either are or are not
offloaded.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Permit offloading qdiscs below RED and TBF. In order to avoid having to
implement trivial propagating callbacks for get_prio_bitmap and
get_tclass_num, extend mlxsw_sp_qdisc_get_prio_bitmap() and
..._get_tclass_num() to handle the lack of the callback as a cue to forward
the request to the parent.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A following patch will enable offloading qdiscs that are deeper than
directly under root qdisc. Currently the topology validation consists of
demanding a root qdisc position for ETS and PRIO. Since RED and TBF are
considered classless, this is enough. In order to prevent some nonsensical
combinations when RED and TBF become classful, introduce a more general
topology validator.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On Spectrum, there are no per-TC TX counters. Instead, mlxsw uses per-prio
counters and aggregates them according to the priomap. Therefore when
priomap changes, the counter base values need to be reset to reflect the
change. Previously, this was only done for the sole child qdisc, but a
following patch makes RED and TBF classful. Thus apply the request to the
whole sub-tree.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Qdisc graft operations have so far been reported at PRIO, ETS and RED, with
RED events ignored, because RED was not considered a classful qdisc. A
following patch will make mlxsw recognize RED and TBF as classful qdiscs,
and thus it is necessary to validate grafting at these qdiscs as well.
Rename the existing graft validator to make it clear that it is a generic
function, and invoke for RED and TBF graft events as well. Drop the
unnecessary PRIO helper and invoke the graft validator directly for PRIO as
well.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently ETS and PRIO are the only offloaded classful qdiscs. Since they
are both similar, their destroy handler is the same, and it handles
children destruction itself. But now it is possible to do it generically
for any classful qdisc. Therefore promote the recursive destruction from
the ETS handler to mlxsw_sp_qdisc_destroy(), so that RED and TBF pick it up
in follow-up patches.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extract from __mlxsw_sp_qdisc_ets_replace() two helpers for handling of one
future FIFO resp. reinitializing the array of future FIFOs.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when keeping track of qdiscs, mlxsw notes the TC and priomap
corresponding to each qdisc. That is fine currently, as there only ever is
one level of qdiscs to update: the direct children of ETS / PRIO. However
as deeper structures are made offloadable, ETS would need to update these
values for the complete subtree, and interim qdiscs would need to remember
to propagate the value.
Instead, reverse the responsibility: child qdiscs can ask their parent what
their TC and priomap are. ETS / PRIO know the answer right away, or there
are defaults for when the root qdisc does not assign them (e.g. when RED is
used as root qdisc). When RED and TBF become classful, they will simply
forward the request up to their parent.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As another qdisc is linked to the TBF, the latter should issue an event to
give drivers a chance to react to the grafting. In other qdiscs, this event
is called GRAFT, so follow suit with TBF as well.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
mlx5-updates-2021-10-18
Maor Maor Gottlieb says:
========================
Use hash to select the affinity port in VF LAG
Current VF LAG architecture is based on QP association with a port.
QP must be created after LAG is enabled to allow association with non-native port.
VM Packets going on slow-path to eSwicth manager (SW path or hairpin) will be transmitted
through a different QP than the VM. This means that Different packets of the same flow might
egress from different physical ports.
This patch-set solves this issue by moving the port selection to be based on the hash function
defined by the bond.
When the device is moved to VF LAG mode, the driver creates TTC (traffic type classifier) flow
tables in order to classify the packet and steer it to the relevant hash function. Similar to what
is done in the mlx5 RSS implementation.
Each rule in the TTC table, forwards the packet to port selection flow table which has one hash
split flow group which contains two "catch all" flow table entries. Each entry point to the
relative uplink port. As shown below:
-------------------
| FT |
TTC rule -> | ----------- |
| FG| FTE --|-|-----> uplink of port #1
| | FTE --|-|-----> uplink of port #2
| ----------- |
-------------------
Hash split flow group is flow group that created as type of HASH_SPLIT and associated with match definer.
The match definer define the fields which included in the hash calculation.
The driver creates the match definer according to the xmit hash policy of the bond driver.
Patches overview:
========================
Minor E-Switch updates:
- Patch #12, dynamic allocation of dest array
- Patch #13, increase number of forward destinations to 32
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Mateusz Palczewski says:
====================
40GbE Intel Wired LAN Driver Updates 2021-10-18
Use single state machine for driver initialization
and for service initialized driver. The init state
machine implemented in init_task() is merged
into the watchdog_task(). The init_task() function
is removed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In randconfig builds, we sometimes come across this warning:
arm-linux-gnueabi-ld: XIP start address may cause MPU programming issues
While this is helpful for actual systems to figure out why it
fails, the warning does not provide any benefit for build testing,
so guard it in a check for CONFIG_COMPILE_TEST, which is usually
set on randconfig builds.
Fixes: 216218308cfb ("ARM: 8713/1: NOMMU: Support MPU in XIP configuration")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
With extra warnings enabled, gcc complains about this function
definition:
arch/arm/probes/kprobes/core.c: In function 'arch_init_kprobes':
arch/arm/probes/kprobes/core.c:465:12: warning: old-style function definition [-Wold-style-definition]
465 | int __init arch_init_kprobes()
Link: https://lore.kernel.org/all/20201027093057.c685a14b386acacb3c449e3d@kernel.org/
Fixes: 24ba613c9d6c ("ARM kprobes: core code")
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
When frame pointers are used instead of the ARM unwinder,
and the kernel is built using clang with an external assembler
and CONFIG_XIP_KERNEL, every file produces two warnings
like:
arm-linux-gnueabi-ld: warning: orphan section `.ARM.extab' from `net/mac802154/util.o' being placed in section `.ARM.extab'
arm-linux-gnueabi-ld: warning: orphan section `.ARM.exidx' from `net/mac802154/util.o' being placed in section `.ARM.exidx'
The same fix was already merged for the normal (non-XIP)
linker script, with a longer description.
Fixes: c39866f268f8 ("arm/build: Always handle .ARM.exidx and .ARM.extab sections")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Both the decompressor code and the kasan logic try to override
the memcpy() and memmove() definitions, which leading to a clash
in a KASAN-enabled kernel with XZ decompression:
arch/arm/boot/compressed/decompress.c:50:9: error: 'memmove' macro redefined [-Werror,-Wmacro-redefined]
#define memmove memmove
^
arch/arm/include/asm/string.h:59:9: note: previous definition is here
#define memmove(dst, src, len) __memmove(dst, src, len)
^
arch/arm/boot/compressed/decompress.c:51:9: error: 'memcpy' macro redefined [-Werror,-Wmacro-redefined]
#define memcpy memcpy
^
arch/arm/include/asm/string.h:58:9: note: previous definition is here
#define memcpy(dst, src, len) __memcpy(dst, src, len)
^
Here we want the set of functions from the decompressor, so undefine
the other macros before the override.
Link: https://lore.kernel.org/linux-arm-kernel/CACRpkdZYJogU_SN3H9oeVq=zJkRgRT1gDz3xp59gdqWXxw-B=w@mail.gmail.com/
Link: https://lore.kernel.org/lkml/202105091112.F5rmd4By-lkp@intel.com/
Fixes: d6d51a96c7d6 ("ARM: 9014/2: Replace string mem* functions for KASan")
Fixes: a7f464f3db93 ("ARM: 7001/2: Wire up support for the XZ decompressor")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
A kernel built with CONFIG_THUMB2_KERNEL=y and using clang as the
assembler could generate non-naturally-aligned v7wbi_tlb_fns which
results in a boot failure. The original commit adding the macro missed
the .align directive on this data.
Link: https://github.com/ClangBuiltLinux/linux/issues/1447
Link: https://lore.kernel.org/all/0699da7b-354f-aecc-a62f-e25693209af4@linaro.org/
Debugged-by: Ard Biesheuvel <ardb@kernel.org>
Debugged-by: Nathan Chancellor <nathan@kernel.org>
Debugged-by: Richard Henderson <richard.henderson@linaro.org>
Fixes: 66a625a88174 ("ARM: mm: proc-macros: Add generic proc/cache/tlb struct definition macros")
Suggested-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
ARM: kasan: Fix __get_user_check failure with kasan
In macro __get_user_check defined in arch/arm/include/asm/uaccess.h,
error code is store in register int __e(r0). When kasan is
enabled, assigning value to kernel address might trigger kasan check,
which unexpectedly overwrites r0 and causes undefined behavior on arm
kasan images.
One example is failure in do_futex and results in process soft lockup.
Log:
watchdog: BUG: soft lockup - CPU#0 stuck for 62946ms! [rs:main
Q:Reg:1151]
...
(__asan_store4) from (futex_wait_setup+0xf8/0x2b4)
(futex_wait_setup) from (futex_wait+0x138/0x394)
(futex_wait) from (do_futex+0x164/0xe40)
(do_futex) from (sys_futex_time32+0x178/0x230)
(sys_futex_time32) from (ret_fast_syscall+0x0/0x50)
The soft lockup happens in function futex_wait_setup. The reason is
function get_futex_value_locked always return EINVAL, thus pc jump
back to retry label and causes looping.
This line in function get_futex_value_locked
ret = __get_user(*dest, from);
is expanded to
*dest = (typeof(*(p))) __r2; ,
in macro __get_user_check. Writing to pointer dest triggers kasan check
and overwrites the return value of __get_user_x function.
The assembly code of get_futex_value_locked in kernel/futex.c:
...
c01f6dc8: eb0b020e bl c04b7608 <__get_user_4>
// "x = (typeof(*(p))) __r2;" triggers kasan check and r0 is overwritten
c01f6dCc: e1a00007 mov r0, r7
c01f6dd0: e1a05002 mov r5, r2
c01f6dd4: eb04f1e6 bl c0333574 <__asan_store4>
c01f6dd8: e5875000 str r5, [r7]
// save ret value of __get_user(*dest, from), which is dest address now
c01f6ddc: e1a05000 mov r5, r0
...
// checking return value of __get_user failed
c01f6e00: e3550000 cmp r5, #0
...
c01f6e0c: 01a00005 moveq r0, r5
// assign return value to EINVAL
c01f6e10: 13e0000d mvnne r0, #13
Return value is the destination address of get_user thus certainly
non-zero, so get_futex_value_locked always return EINVAL.
Fix it by using a tmp vairable to store the error code before the
assignment. This fix has no effects to non-kasan images thanks to compiler
optimization. It only affects cases that overwrite r0 due to kasan check.
This should fix bug discussed in Link:
[1] https://lore.kernel.org/linux-arm-kernel/0ef7c2a5-5d8b-c5e0-63fa-31693fd4495c@gmail.com/
Fixes: 421015713b30 ("ARM: 9017/2: Enable KASan for ARM")
Signed-off-by: Lexi Shao <shaolexi@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Commit 344179fc7ef4 ("ARM: 9106/1: traps: use get_kernel_nofault instead
of set_fs()") replaced an occurrence of __get_user() with
get_kernel_nofault(), but inverted the sense of the conditional in the
process, resulting in no values to be printed at all.
I.e., every exception stack now looks like this:
Exception stack(0xc18d1fb0 to 0xc18d1ff8)
1fa0: ???????? ???????? ???????? ????????
1fc0: ???????? ???????? ???????? ???????? ???????? ???????? ???????? ????????
1fe0: ???????? ???????? ???????? ???????? ???????? ????????
which is rather unhelpful.
Fixes: 344179fc7ef4 ("ARM: 9106/1: traps: use get_kernel_nofault instead of set_fs()")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
