| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull deny_write_access revert from Christian Brauner:
"It turns out that the mold linker relies on the deny_write_access()
mechanism for executables.
The mold linker tries to open a file for writing and if ETXTBSY is
returned mold falls back to creating a new file"
* tag 'vfs-6.13.exec.deny_write_access.revert' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
Revert "fs: don't block i_writecount during exec"
|
|
It is permitted for a plane to be configured such that none
of it is on-screen via either negative dest rectangle X,Y
offset, or an offset that is greater than the crtc dimensions.
These planes were resized via drm_atomic_helper_check_plane_state
such that the source rectangle had a zero width or height, but
they still created a dlist entry even though they contributed
no pixels. In the case of vc6_plane_mode_set, that it could result
in negative values being written into registers, which caused
incorrect behaviour.
Drop planes that result in a source width or height of 0 pixels
or an on-screen size of 0 pixels to avoid the incorrect rendering.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-28-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
The default was to have enable_bg_fill disabled and the first
plane set it if it wasn't opaque and covering the whole screen.
However that meant that if no planes were enabled, then the
background fill wasn't enabled, and would give a striped
output from the uninitialised output buffer.
Initialise it to enabled to avoid this.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-27-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
Some code path in vc4 are conditional to a generation and cannot be
executed on others. Let's put a WARN_ON if that ever happens.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-26-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
The D-step has increased FIFO sizes of the MAI_THR blocks,
resulting in changes to the register masking. Add support for
it.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-25-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
There are a few minor changes in the display list generation
for the D-step of the chip, so add them.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-24-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
The registers have been moved around, and a couple of minor changes
made, so adapt for this.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-23-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
Add in the compatible string and VC4_GEN_ enum for the D-step
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-22-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
The BCM2712 features a simpler TXP called MOPLET. Let's add support for
it.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-21-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
The BCM2712 has an evolution of what used to be called TXP in the
earlier SoCs, but is now called MOP.
There's a few differences still, so we can add a new compatible to deal
with them easily.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-20-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
Starting with BCM2712, we'll have a two TXP. Let's follow the HDMI
example and add two encoder types for TXP: TXP0 and TXP1.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-19-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
We'll have multiple TXP instances in the BCM2712, so we can't use a
single encoder type anymore. Let's tie the encoder type to the
compatible.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-18-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
The BCM2712 MOP and MOPLET can handle addresses larger than 32bits
through an extra register. We can easily support it and make it
conditional based on the compatible through a boolean in our variant
structure.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-17-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
The new writeback controllers that can be found on the BCM2712 require
to have their horizontal and vertical size reduced by one.
Let's tie that behaviour to the compatible so we can support both the
new and old controllers.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-16-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
The MOPLET doesn't have the BYTE_ENABLE field to set, but the TXP and
MOP do, so let's add a boolean to control whether or not we need to set
it.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-15-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
The TXP data structure has a name too generic for the multiple variants
we'll have to support. Let's rename it to mention the SoC it applies to.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-14-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
The BCM2712 will have several TXP with small differences. Let's add a
structure tied to the compatible to deal with those differences.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-13-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
The HDMI controllers found in the BCM2712 are largely the ones found in
the BCM2711 with a different PHY.
There's some difference with how timings are split between registers,
and HDMI1 is now able to run at 4k/60Hz.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-12-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
The PixelValves found on the BCM2712 are similar to the ones found in
the previous generation.
Compared to BCM2711:
- the pixelvalves only drive one HDMI controller each
- HDMI1 PixelValve has a FIFO long enough to support 4k at 60Hz
- support has been added for odd horizontal timings whilst at 2pixels/clock
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-11-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
The HVS found in the BCM2712, while having a similar role, is very
different from the one found in the previous SoCs. Indeed, the register
layout is fairly different, and the DLIST format is new as well.
Let's introduce the needed functions to support the new HVS.
This commit adds the C-step register layout. The D-step will be
added later.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-10-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
The BCM2712 has an improved display pipeline, most notably with a
different HVS and only HDMI and writeback outputs.
Let's introduce it as a new VideoCore generation and compatible.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-9-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
The BCM2712 SoC comes with a new variation of the videocore display
pipeline. Let's create a new compatible for it.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-8-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
The BCM2712 has a MOPLET controller which is basically a TXP without the
transpose feature.
Express that by adding a new compatible for it.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-7-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
The BCM2712 has a MOP controller which is basically a new revision of
the TXP.
Express that by adding a new compatible for it.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-6-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
The BCM2712 has 3 different pixelvalves that are similar to the ones
found in the previous generations but with slightly different
capabilities.
Express that using a new set of compatibles.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-5-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
The BCM2712 has a completely different HVS than the previous
generations, so let's add a new compatible for it.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-4-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
The BCM2712 HDMI controller uses a slightly different HDMI controller
than the BCM2711, and a completely different PHY.
Let's introduce a new compatible for it.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-3-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
The frame count values moved within registers DISPSTAT1 and
DISPSTAT2 with GEN5, so update the accessor function to
accommodate that.
Fixes: b51cd7ad143d ("drm/vc4: hvs: Fix frame count register readout")
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-2-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
Use of_device_get_match_data to retrieve the generation value
as set in the struct of_device_id, rather than manually comparing
compatible strings.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025-drm-vc4-2712-support-v2-1-35efa83c8fc0@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
|
|
21MES00B00
New ThinkPads need new quirk entries. Ilya has tested this one.
Laptop product id is 21MES00B00, though the shorthand 21ME works.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219533
Cc: stable@vger.kernel.org
Signed-off-by: Ilya Zverev <ilya@zverev.info>
Link: https://patch.msgid.link/20241127134420.14471-1-ilya@zverev.info
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 8a13897fb0daa ("mm: userfaultfd: support UFFDIO_POISON for
hugetlbfs") added support for PTE_MARKER_POISONED for hugetlbfs, but
PTE_MARKER also needs support for swap entries. For s390, swap entries
were only supported on PTE level, not on the PMD/PUD levels that are used
for large hugetlbfs mappings.
Therefore, when writing a PTE_MARKER_POISONED entry, the resulting entry
on PMD/PUD level would be an invalid / empty entry. Further access would
then generate a pagefault loop, instead of the expected SIGBUS. It is a
loop inside the kernel, but interruptible and uffd fault handling also
calls schedule() in between, so at least it won't completely block the
system.
Previous commits prepared support for swap entries on PMD/PUD levels.
PTE_MARKER support for hugetlbfs can now be enabled by simply adding an
extra is_pte_marker() check to huge_pte_none_mostly(). Fault handling
code also needs to be adjusted to expect the VM_FAULT_HWPOISON_LARGE
fault flag, which was not possible on s390 before.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Introduce region-third (PUD) and segment table (PMD) swap entries, and
make hugetlbfs RSTE <-> PTE conversion code aware of them, so that they
can be used for hugetlbfs PTE_MARKER entries. Future work could also
build on this to enable THP_SWAP and THP_MIGRATION for s390.
Similar to PTE swap entries, bits 0-51 can be used to store the swap
offset, but bits 57-61 cannot be used for swap type because that overlaps
with the INVALID and TABLE TYPE bits. PMD/PUD swap entries must be invalid,
and have a correct table type so that pud_folded() check still works.
Bits 53-57 can be used for swap type, but those include the PROTECT bit.
So unlike swap PTEs, the PROTECT bit cannot be used to mark the swap entry.
Use the "Common-Segment/Region" bit 59 instead for that.
Also remove the !MACHINE_HAS_NX check in __set_huge_pte_at(). Otherwise,
that would clear the _SEGMENT_ENTRY_NOEXEC bit also for swap entries, where
it is used for encoding the swap type. The architecture only requires this
bit to be 0 for PTEs, with !MACHINE_HAS_NX, not for segment or region-third
entries. And the check is also redundant, because after __pte_to_rste()
conversion, for non-swap PTEs it would only be set if it was already set in
the PTE, which should never be the case for !MACHINE_HAS_NX.
This is a prerequisite for hugetlbfs PTE_MARKER support on s390, which
is needed to fix a regression introduced with commit 8a13897fb0da
("mm: userfaultfd: support UFFDIO_POISON for hugetlbfs"). That commit
depends on the availability of swap entries for hugetlbfs, which were
not available for s390 so far.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Introduce region-third and segment table entry present SW bits, and adjust
pmd/pud_present() accordingly.
Also add pmd/pud_present() checks to pmd/pud_leaf(), to return false for
future swap entries. Same logic applies to pmd_trans_huge(), make that
return pmd_leaf() instead of duplicating the same check.
huge_pte_offset() also needs to be adjusted, current code would return
NULL for !pud_present(). Use the same logic as in the generic version,
which allows for !pud_present() swap entries.
Similar to PTE, bit 63 can be used for the new SW present bit in region
and segment table entries. For segment-table entries (PMD) the architecture
says that "Bits 62-63 are available for programming", so they are safe to
use. The same is true for large leaf region-third-table entries (PUD).
However, for non-leaf region-third-table entries, bits 62-63 indicate the
TABLE LENGTH and both must be set to 1. But such entries would always be
considered as present, so it is safe to use bit 63 as PRESENT bit for PUD.
They also should not conflict with bit 62 potentially later used for
preserving SOFT_DIRTY in swap entries, because they are not swap entries.
Valid PMDs / PUDs should always have the present bit set, so add it to
the various pgprot defines, and also _SEGMENT_ENTRY which is OR'ed e.g.
in pmd_populate(). _REGION3_ENTRY wouldn't need any change, as the present
bit is already included in the TABLE LENGTH, but also explicitly add it
there, for completeness, and just in case the bit would ever be changed.
gmap code needs some adjustment, to also OR the _SEGMENT_ENTRY, like it
is already done gmap_shadow_pgt() when creating new PMDs, but not in
__gmap_link(). Otherwise, the gmap PMDs would not be considered present,
e.g. when using pmd_leaf() checks in gmap code. The various WARN_ON
checks in gmap code also need adjustment, to tolerate the new present
bit.
This is a prerequisite for hugetlbfs PTE_MARKER support on s390, which
is needed to fix a regression introduced with commit 8a13897fb0da
("mm: userfaultfd: support UFFDIO_POISON for hugetlbfs"). That commit
depends on the availability of swap entries for hugetlbfs, which were
not available for s390 so far.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Rearrange region-third and segment table entry SW bits, in order to
make room for future encoding of region/segment table swap entries.
Also adjust _SEGMENT_ENTRY_GMAP_UC and _SEGMENT_ENTRY_GMAP_IN bits in
gmap code. Those should only apply for gmap PMDs, and not really depend
on or conflict with host PMD bits, but for consistency also adjust them:
- _SEGMENT_ENTRY_GMAP_UC "dirty (migration)" was using the same bit as
_SEGMENT_ENTRY_SOFT_DIRTY in the host PMD -> make it use the new
SOFT_DIRTY bit 63 (0x0002)
- _SEGMENT_ENTRY_GMAP_IN "invalidation notify bit" was using 0x8000,
which was an unused bit in the host PMD, that is now used for
_SEGMENT_ENTRY_WRITE -> make it use bit 52 (0x0800) instead, which is
still unused in the host PMD
This is a prerequisite for hugetlbfs PTE_MARKER support on s390, which
is needed to fix a regression introduced with commit 8a13897fb0da
("mm: userfaultfd: support UFFDIO_POISON for hugetlbfs"). That commit
depends on the availability of swap entries for hugetlbfs, which were
not available for s390 so far.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
kvm_s390_update_topology_change_report() modifies a single bit within
sca_utility using cmpxchg(). Given that the size of the sca_utility union
is two bytes this generates very inefficient code. Change the size to four
bytes, so better code can be generated.
Even though the size of sca_utility doesn't reflect architecture anymore
this seems to be the easiest and most pragmatic approach to avoid
inefficient code.
Acked-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20241126102515.3178914-4-hca@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Within sca_clear_ext_call() cmpxchg() is used to clear one or two bytes
(depending on sca format). The cmpxchg() calls are not supposed to fail; if
so that would be a bug. Given that cmpxchg() usage on one and two byte
areas generates very inefficient code, replace them with block concurrent
WRITE_ONCE() calls, and remove the WARN_ON().
Acked-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20241126102515.3178914-3-hca@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Convert all cmpxchg() loops to try_cmpxchg() loops. With gcc 14 and the
usage of flag output operands in try_cmpxchg() this allows the compiler to
generate slightly better code.
Acked-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20241126102515.3178914-2-hca@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The result of xchg() is not used, and in addition it is used on a one byte
memory area which leads to inefficient code.
Use WRITE_ONCE() instead to achieve the same result with much less
generated code.
Acked-by: Harald Freudenberger <freude@linux.ibm.com>
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
This reverts commit 2a010c41285345da60cece35575b4e0af7e7bf44.
Rui Ueyama <rui314@gmail.com> writes:
> I'm the creator and the maintainer of the mold linker
> (https://github.com/rui314/mold). Recently, we discovered that mold
> started causing process crashes in certain situations due to a change
> in the Linux kernel. Here are the details:
>
> - In general, overwriting an existing file is much faster than
> creating an empty file and writing to it on Linux, so mold attempts to
> reuse an existing executable file if it exists.
>
> - If a program is running, opening the executable file for writing
> previously failed with ETXTBSY. If that happens, mold falls back to
> creating a new file.
>
> - However, the Linux kernel recently changed the behavior so that
> writing to an executable file is now always permitted
> (https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=2a010c412853).
>
> That caused mold to write to an executable file even if there's a
> process running that file. Since changes to mmap'ed files are
> immediately visible to other processes, any processes running that
> file would almost certainly crash in a very mysterious way.
> Identifying the cause of these random crashes took us a few days.
>
> Rejecting writes to an executable file that is currently running is a
> well-known behavior, and Linux had operated that way for a very long
> time. So, I don’t believe relying on this behavior was our mistake;
> rather, I see this as a regression in the Linux kernel.
Quoting myself from commit 2a010c412853 ("fs: don't block i_writecount during exec")
> Yes, someone in userspace could potentially be relying on this. It's not
> completely out of the realm of possibility but let's find out if that's
> actually the case and not guess.
It seems we found out that someone is relying on this obscure behavior.
So revert the change.
Link: https://github.com/rui314/mold/issues/1361
Link: https://lore.kernel.org/r/4a2bc207-76be-4715-8e12-7fc45a76a125@leemhuis.info
Cc: <stable@vger.kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Intel SoundWire machine driver always uses Pin number 2 and above.
Currently, the pin number is used as the FW DAI index directly. As a
result, FW DAI 0 and 1 are never used. That worked fine because we use
up to 2 DAIs in a SDW link. Convert the topology pin index to ALH dai
index, the mapping is using 2-off indexing, iow, pin #2 is ALH dai #0.
The issue exists since beginning. And the Fixes tag is the first commit
that this commit can be applied.
Fixes: b66bfc3a9810 ("ASoC: SOF: sof-audio: Fix broken early bclk feature for SSP")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://patch.msgid.link/20241127092955.20026-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Following commit 13f58267cda3 ("ASoC: soc.h: don't create dummy
Component via COMP_DUMMY()"), COMP_DUMMY() became an array with zero
length, and only gets populated with the dummy struct after the card is
registered. Since the sound card driver's probe happens before the card
registration, accessing any of the members of a dummy component during
probe will result in undefined behavior.
This can be observed in the mt8188 and mt8195 machine sound drivers. By
omitting a dai link subnode in the sound card's node in the Devicetree,
the default uninitialized dummy codec is used, and when its dai_name
pointer gets passed to strcmp() it results in a null pointer dereference
and a kernel panic.
In addition to that, set_card_codec_info() in the generic helpers file,
mtk-soundcard-driver.c, will populate a dai link with a dummy codec when
a dai link node is present in DT but with no codec property.
The result is that at probe time, a dummy codec can either be
uninitialized with num_codecs = 0, or be an initialized dummy codec,
with num_codecs = 1 and dai_name = "snd-soc-dummy-dai". In order to
accommodate for both situations, check that num_codecs is not zero
before accessing the codecs' fields but still check for the codec's dai
name against "snd-soc-dummy-dai" as needed.
While at it, also drop the check that dai_name is not null in the mt8192
driver, introduced in commit 4d4e1b6319e5 ("ASoC: mediatek: mt8192:
Check existence of dai_name before dereferencing"), as it is actually
redundant given the preceding num_codecs != 0 check.
Fixes: 13f58267cda3 ("ASoC: soc.h: don't create dummy Component via COMP_DUMMY()")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Fei Shao <fshao@chromium.org>
Acked-by: Trevor Wu <trevor.wu@mediatek.com>
Link: https://patch.msgid.link/20241126-asoc-mtk-dummy-panic-v1-1-42d53e168d2e@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add condition check to register ACP PDM sound card by reading
_WOV acpi entry.
Fixes: 5426f506b584 ("ASoC: amd: Add support for enabling DMIC on acp6x via _DSD")
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://patch.msgid.link/20241127112227.227106-1-venkataprasad.potturu@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch fixes a coding style issue in the alignment of parameters
in the function i2c_smbus_write_bytes(). It replaces spaces with tabs for
alignment, as per the coding style guidelines.
Signed-off-by: Liam Zuiderhoek <zuiderhoekl@gmail.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Instead of having them all available, mark them all as "fail-needs-probe"
and have the implementation try to probe which one is present.
Also remove the shared resource workaround by moving the pinctrl entry
for the trackpad interrupt line back into the individual trackpad nodes.
Cc: <stable+noautosel@kernel.org> # Needs accompanying new driver to work
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Some devices are designed and manufactured with some components having
multiple drop-in replacement options. These components are often
connected to the mainboard via ribbon cables, having the same signals
and pin assignments across all options. These may include the display
panel and touchscreen on laptops and tablets, and the trackpad on
laptops. Sometimes which component option is used in a particular device
can be detected by some firmware provided identifier, other times that
information is not available, and the kernel has to try to probe each
device.
This change attempts to make the "probe each device" case cleaner. The
current approach is to have all options added and enabled in the device
tree. The kernel would then bind each device and run each driver's probe
function. This works, but has been broken before due to the introduction
of asynchronous probing, causing multiple instances requesting "shared"
resources, such as pinmuxes, GPIO pins, interrupt lines, at the same
time, with only one instance succeeding. Work arounds for these include
moving the pinmux to the parent I2C controller, using GPIO hogs or
pinmux settings to keep the GPIO pins in some fixed configuration, and
requesting the interrupt line very late. Such configurations can be seen
on the MT8183 Krane Chromebook tablets, and the Qualcomm sc8280xp-based
Lenovo Thinkpad 13S.
Instead of this delicate dance between drivers and device tree quirks,
this change introduces a simple I2C component prober. For any given
class of devices on the same I2C bus, it will go through all of them,
doing a simple I2C read transfer and see which one of them responds.
It will then enable the device that responds.
This requires some minor modifications in the existing device tree.
The status for all the device nodes for the component options must be
set to "fail-needs-probe". This makes it clear that some mechanism is
needed to enable one of them, and also prevents the prober and device
drivers running at the same time.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Add GPIO support to the simple helpers for the I2C OF component prober.
Components that the prober intends to probe likely require their
regulator supplies be enabled, and GPIOs be toggled to enable them or
bring them out of reset before they will respond to probe attempts.
Regulator supplies were handled in the previous patch.
The assumption is that the same class of components to be probed are
always connected in the same fashion with the same regulator supply
and GPIO. The names may vary due to binding differences, but the
physical layout does not change.
This supports at most one GPIO pin. The user must specify the GPIO name,
the polarity, and the amount of time to wait after the GPIO is toggled.
Devices with more than one GPIO pin likely require specific power
sequencing beyond what generic code can easily support.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Add helpers to do regulator management for the I2C OF component prober.
Components that the prober intends to probe likely require their
regulator supplies be enabled, and GPIOs be toggled to enable them or
bring them out of reset before they will respond to probe attempts.
GPIOs will be handled in the next patch.
The assumption is that the same class of components to be probed are
always connected in the same fashion with the same regulator supply
and GPIO. The names may vary due to binding differences, but the
physical layout does not change.
This set of helpers supports at most one regulator supply. The user
must specify the node from which the supply is retrieved. The supply
name and the amount of time to wait after the supply is enabled are
also given by the user.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Some devices are designed and manufactured with some components having
multiple drop-in replacement options. These components are often
connected to the mainboard via ribbon cables, having the same signals
and pin assignments across all options. These may include the display
panel and touchscreen on laptops and tablets, and the trackpad on
laptops. Sometimes which component option is used in a particular device
can be detected by some firmware provided identifier, other times that
information is not available, and the kernel has to try to probe each
device.
This change attempts to make the "probe each device" case cleaner. The
current approach is to have all options added and enabled in the device
tree. The kernel would then bind each device and run each driver's probe
function. This works, but has been broken before due to the introduction
of asynchronous probing, causing multiple instances requesting "shared"
resources, such as pinmuxes, GPIO pins, interrupt lines, at the same
time, with only one instance succeeding. Work arounds for these include
moving the pinmux to the parent I2C controller, using GPIO hogs or
pinmux settings to keep the GPIO pins in some fixed configuration, and
requesting the interrupt line very late. Such configurations can be seen
on the MT8183 Krane Chromebook tablets, and the Qualcomm sc8280xp-based
Lenovo Thinkpad 13S.
Instead of this delicate dance between drivers and device tree quirks,
this change introduces a simple I2C component probe function. For a
given class of devices on the same I2C bus, it will go through all of
them, doing a simple I2C read transfer and see which one of them responds.
It will then enable the device that responds.
This requires some minor modifications in the existing device tree. The
status for all the device nodes for the component options must be set
to "fail-needs-probe". This makes it clear that some mechanism is
needed to enable one of them, and also prevents the prober and device
drivers running at the same time.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
There are cases where drivers would go through child device nodes and
operate on only the ones whose node name starts with a given prefix.
Provide a helper for these users. This will mainly be used in a
subsequent patch that implements a hardware component prober for I2C
busses.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Add a helper function to add string property updates to an OF changeset.
This is similar to of_changeset_add_prop_string(), but instead of adding
the property (and failing if it exists), it will update the property.
This shall be used later in the DT hardware prober.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
