| Age | Commit message (Collapse) | Author |
|---|
|
I tested savagefb on 3 different Savage 4 cards:
Diamond Stealth III S520
Number Nine SR9
Datapath Horizon 2S (two savage chips on a PCI card)
it worked except the DDC which did not work on any of them.
Looking at the BIOS code, it does not use MMIO register 0xff20 but CRT
register 0xa0 or 0xb1 - depending on the chip revision and something in
register 0xa6. With this patch, DDC works fine on all 3 cards (even on
the second head of Horizon 2S - although it does not display anything as
it's misconfigured because of missing BIOS).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The CONFIG_FB_MATROX_G ifdef isn't necessary at this point, because it is
checked in an outer ifdef level already and has no effect here.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In this case the logic is very similar but the IRQs are not exposed and
the device is not picked up via PCI
Based on a separate internal whitney point driver by Yin Kangkai.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Yin Kangkai <kangkai.yin@intel.com>
Cc: Alek Du <alek.du@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Deweird this driver.
Cc: Alek Du <alek.du@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Topcliff PCH is the platform controller hub that is going to be used in
Intel's upcoming general embedded platform. All IO peripherals in
Topcliff PCH are actually devices sitting on AMBA bus. Topcliff PCH has
GPIO I/F. Using this I/F, it is able to access system devices connected
to GPIO.
[akpm@linux-foundation.org: ese DEFINE_PCI_DEVICE_TABLE (per Joe Perches)]
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Tomoya MORINAGA <morinaga526@dsn.okisemi.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some ADP5588 functions take a pointer to an i2c_client, but if the i2c
header doesn't happen to be included first, we hit the standard "struct
declared inside parameter list" warnings from gcc. So add a simple
forward decl of the i2c_client struct.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Common code interprets this as a signed value (a negative value is used to
request dynamic ID allocation), so make sure the platform data has proper
types to support that.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Implement irq_chip functionality on ADP5588/5587 GPIO expanders. Only
level sensitive interrupts are supported. Interrupts provided by this
irq_chip must be requested using request_threaded_irq().
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add support for generic 74x164 serial-in/parallel-out 8-bits shift
register. This driver can be used as a GPIO output expander.
[akpm@linux-foundation.org: remove unused local `refresh']
Signed-off-by: Miguel Gaio <miguel.gaio@efixo.com>
Signed-off-by: Juhos Gabor <juhosg@openwrt.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some versions of the hardware can trash the IER register if simultaneous
interrupts occur. This patch works around it by using a local copy of the
register and restoring it after every interrupt.
Signed-off-by: Tomas Hallenberg <tomas.hallenberg@pelagicore.com>
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
commit 7444a72effa632fcd8edc566f88 ("gpiolib: allow user-selection")
removed HAVE_GPIO_LIB Kconfig symbol, but the header file still uses the
name [to confuse readers wrt #ifdef/#else/#endif location].
The real Kconfig symbol nowadays is CONFIG_GPIOLIB.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The basic GPIO controllers may be found in various on-board FPGA and ASIC
solutions that are used to control board's switches, LEDs, chip-selects,
Ethernet/USB PHY power, etc.
These controllers may not provide any means of pin setup
(in/out/open drain).
The driver supports:
- 8/16/32/64 bits registers;
- GPIO controllers with clear/set registers;
- GPIO controllers with a single "data" register;
- Big endian bits/GPIOs ordering (mostly used on PowerPC).
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>,
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add the "alarm" function to the jz4740 RTC. Interrupts will now be raised
when the "alarm" time is reached.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The DS3232 RTC driver only has the tick function. Add an alarm function
so the driver is complete.
Signed-off-by: Lan Chunhe-B25806 <b25806@freescale.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add "rtc_valid_tm" in s3c_rtc_gettime() as per Wan ZongShun's suggestion.
Suggested-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Change RTC initialization method in probe(). The 'rtc_valid_tm(tm)' can
check whether RTC BCD is valid or not. And change the method of checking
because the previous method cannot validate RTC BCD registers properly.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix debug message format.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The alarm_irq_enable function should be implemented to support RTC alarm.
And fix tabs instead of white space around the proc field.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Current s3c_rtc_getalarm() sets missing field of alarm time with 0xff.
But this value should be -1 according to drivers/rtc/interface.c.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
S3C2410_RTCCON of TYPE_S3C64XX RTC should be read/written by readw and
writew, because TYPE_S3C64XX RTC uses bit 8 and 9. And TYPE_S3C2410 RTC
also can access it by readw and writew.
[atul.dahiya@samsung.com: tested on smdk2416]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Tested-by: Atul Dahiya <atul.dahiya@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The rtc-omap driver currently hardcodes the RTC wakeup capability to be
"not capable". While this seems to be true for existing OMAP1 boards
which are not wired for this, the DA850/OMAP-L138 SoC, the RTC can always
be wake up source from its "deep sleep" mode.
This patch lets the wakeup capability be set from platform data and does
not override the setting from the driver. For DA850/OMAP-L138, this is
done from arch/arm/mach-davinci/devices-da8xx.c:da8xx_register_rtc()
Note that this patch does not change the behavior on any existing OMAP1
board since the platform device registration sets the wakeup capability to
0 by default.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If device_register() fails then call put_device(). See comment to
device_register.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The rest of the driver had debug markings already. This also standardizes
the usage of "dev" a bit.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
By unifying the RTC_ISTAT clearing steps, we shrink the interrupt handler
and avoid multiple writes to the hardware registers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add an RTC driver for the built-in RTC in the LPC32XX SoC. This patch
includes updates from the initial review comments and updates from the v3
review.
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Durgesh Pattamatta <durgesh.pattamatta@nxp.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When all VT's are in use, VT_OPENQRY casts -1 to unsigned char before
returning it to userspace as an int. VT255 is not the next available
console.
Signed-off-by: Graham Gower <graham.gower@gmail.com>
Cc: Greg KH <greg@kroah.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Put basic system information in the dmesg log. There are lots of dmesg
logs on the web, and it would be useful if they contained this information
for debugging platform problems. "BOARD/PRODUCT" format copied from
show_regs_common(), which is used in the oops path.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Christoph reported a nice splat which illustrated a race in the new stack
based kmap_atomic implementation.
The problem is that we pop our stack slot before we're completely done
resetting its state -- in particular clearing the PTE (sometimes that's
CONFIG_DEBUG_HIGHMEM). If an interrupt happens before we actually clear
the PTE used for the last slot, that interrupt can reuse the slot in a
dirty state, which triggers a BUG in kmap_atomic().
Fix this by introducing kmap_atomic_idx() which reports the current slot
index without actually releasing it and use that to find the PTE and delay
the _pop() until after we're completely done.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reported-by: Christoph Hellwig <hch@infradead.org>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It appears i386 uses kmap_atomic infrastructure regardless of
CONFIG_HIGHMEM which results in a compile error when highmem is disabled.
Cure this by providing the needed few bits for both CONFIG_HIGHMEM and
CONFIG_X86_32.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We leak 256 bytes here on this error path.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
When quotaon(8) races with __dquot_initialize() or dqget() fails because
of EIO, ENOSPC, or similar error, we could possibly dereference NULL pointer
in inode->i_dquot[cnt]. Add proper checking.
Reported-by: Dmitry Monakhov <dmonakhov@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Update missing/broken argument descriptions and fix formatting.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
"wakup"
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
"excpet"
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Fix a typo, break long lines and use E3FSBLK on ext3_fsblk_t.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Convert atomic_inc(&bh->b_count) to get_bh(bh) for consistency.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
'buffer_head' should be 'journal_head'.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Fail journal creation if __getblk() returns NULL. unlikely() is
added because it is called in a loop and we've been OK without
the check until now.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
bh->b_data is already a pointer to char so casts to 'char *' should
be meaningless. Remove them.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Fix mount-count check to emit warning only if s_max_mnt_count
is greater than 0 according to man tune2fs(8). Also removes
unnecessary casts.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
__dquot_transfer accidentally called flush_warnings for a wrong set of
dquots which could result in quota warnings being issued with a wrong
identification. Also when operation fails because of EDQUOT, there's no
need check for issuing information message about user getting below limits
(no transfer has actually happened).
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
I've got following lockup:
dquot_disable dquot_transfer
->dqget()
sb_has_quota_active
dqopt->flags &= ~dquot_state_flag(f, cnt) atomic_inc(dq->dq_count)
->drop_dquot_ref(sb, cnt);
down_write(dqptr_sem)
inode->i_dquot[cnt] = NULL ->__dquot_transfer
invalidate_dquots(sb, cnt); down_write(&dqptr_sem)
->wait for dq_wait_unused inode->i_dquot = new_dquot
/* wait forever */ ^^^^New quota user^^^^^^
We cannot allow new references to dquots from inodes after drop_dquot_ref()
has removed them. We have to recheck quota state under dqptr_sem and before
assignment, as we do it in dquot_initialize().
Signed-off-by: Dmitry Monakhov <dmonakhov@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Convert set/clear_bit(BH_JWrite, ...) to set/clear_buffer_jwrite()
for consistency.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
This fixes a WARN backtrace in mark_buffer_dirty() that occurs during unmount
when the underlying block device is removed. This bug has been seen on System
Z when removing all paths from a multipath-backed ext3 mount; on System P when
injecting enough PCI EEH errors to make the SCSI controller go offline; and
similar warnings have been seen (and patched) with ext2/ext4.
The super block update from a previous operation has marked the buffer as in
error, and the flag has to be cleared before doing the update. Similar changes
have been made to ext4 by commit 914258bf2cb22bf4336a1b1d90c551b4b11ca5aa.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Remove goto statement which jumps to very next line. Also remove
target label because it is no longer used anywhere.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
