| Age | Commit message (Collapse) | Author |
|---|
|
Quite a few drivers have a implementation of the get_timeout_clock
callback which simply returns the result of clk_get_rate on the device's
clock. This patch adds a common implementation of this to the sdhci-pltfm
module and replaces all custom implementations with the common one.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The protocol related code is moved to core stack. So update the host
driver accordingly.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Tested-by: Tim Wang <wangtt@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
When switching SD and SDIO cards from 3.3V to 1.8V signal levels, the
clock should be gated for 5 ms during the step. After enabling the
clock, the host should wait for at least 1 ms before checking for
failure. Failure by the card to switch is indicated by dat[0:3] being
pulled low. The host should check for this condition and power-cycle
the card if failure is indicated.
Add a retry mechanism for the SDIO case.
If the voltage switch fails repeatedly, give up and continue the
initialization using the original voltage.
This patch places a couple of requirements on the host driver:
1) mmc_set_ios with ios.clock = 0 must gate the clock
2) mmc_power_off must actually cut the power to the card
3) The card_busy host_ops member must be implemented
if these requirements are not fulfilled, the 1.8V signal voltage switch
will still be attempted but may not be successful.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Allow callers to access the start_signal_voltage_switch host_ops
member without going through any cmd11 logic. This is mostly a
preparation for the following signal voltage switch patch.
Also, reset ios.signal_voltage to its original value if
start_signal_voltage_switch fails.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This host_ops member is used to test if the card is signaling busy by
pulling dat[0:3] low.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Add mmc_power_cycle which can be used to power cycle for instance
SD-cards.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
SET_BLOCK_COUNT CMD23 is needed for all access to RPMB partition. If
block count is not set by CMD23, all subsequent read/write commands fail
as per eMMC specification. So, If the host does not support CMD23, do not
expose RPMB partition.
Accessing RPMB partition can cause hang / huge delay for hosts which do
not support CMD23.
Signed-off-by: Balaji T K <balajitk@ti.com>
Reported-and-Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This driver handles the virtual MMC device present in the Goldfish emulator.
The patch folds together initial work from Mike Lockwood and patches by
San Mehat, Jun Nakajima and Tom Keel <thomas.keel@intel.com> plus cleanups
by Alan Cox to get it all into 3.6 shape.
Signed-off-by: Mike A. Chan <mikechan@google.com>
[cleaned up and x86 support added]
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>
Signed-off-by: Xiaohui Xin <xiaohui.xin@intel.com>
Signed-off-by: Jun Nakajima <jun.nakajima@intel.com>
Signed-off-by: Bruce Beare <bruce.j.beare@intel.com>
[Moved to 3.4]
Signed-off-by: Tom Keel <thomas.keel@intel.com>
[Moved to 3.7]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
None of mmc drivers implements bus-width as a required device tree
property. Instead, some drivers like atmel-mci, dw_mmc, sdhci-s3c
implement it as an optional one, and will force bus width to be 1
when the property is absent. Let's change the common binding to
reflect what the drivers are usually doing.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The i.MX esdhc has a nonstandard bit layout for the SDHCI_HOST_CONTROL
register. To support 8bit bus width on i.MX populate the platform_bus_width
callback. This is tested on an i.MX25, but should according to the datasheets
work on the other i.MX using this hardware aswell. The i.MX6, while having
a SDHCI_SPEC_300 controller, still uses the same nonstandard register layout.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The 8bit in the function name is misleading. When set, it will be
used to set the bus width, regardless of whether 8bit or another
bus width is requested, so change the function name to
platform_bus_width.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
SDHCI core will try to use Auto CMD23 for mmc card. Currently, we will
see the following message with mmc card on usdhc due to the lacking of
Auto CMD23 support in the driver.
$ mmc0: new high speed MMC card at address 0001
mmcblk1: mmc0:0001 MMC02G 1.87 GiB
mmcblk1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
mmcblk1: retrying using single block read
mmcblk1:
Enable Auto CMD23 support for usdhc so that mmc card can work in
multiple block mode.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
It's another violation to SDHC spec that software reset on usdhc
does not reset MIX_CTRL register. Have to do it manually, otherwise
the preserving of the register bits (e.g. AC23EN) may cause mmc card
fail to be initialized.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The combining of SDHCI_TRANSFER_MODE and SDHCI_COMMAND writes is only
required for esdhc, but not necessarily for usdhc. Different from
esdhc where the bits for transfer mode and command are all in the same
register CMD_XFR_TYP, usdhc has a newly introduced register MIX_CTRL
to hold transfer mode bits. So it makes more sense to separate transfer
mode from command write for usdhc.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Cache control is an eMMC feature and in therefore should be
part of MMC's bus resume operations, performed in mmc_suspend,
rather than in the generic mmc_suspend_host().
Signed-off-by: Maya Erez <merez@codeaurora.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Add maintainer entry for the Synopsys DW host driver which is used in
various SOC including EXYNOS series. As Will Newton will no longer be
able to take care of dw_mmc*, I and Jaehoon Chung are willing to maintain
it.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
3f175a6e5 (mmc: sdhci-esdhc-imx: remove ESDHC_CD_GPIO handling from IO
accessory) introduced the following build warnings:
drivers/mmc/host/sdhci-esdhc-imx.c:149:30: warning: unused variable 'boarddata' [-Wunused-variable]
drivers/mmc/host/sdhci-esdhc-imx.c:181:30: warning: unused variable 'boarddata' [-Wunused-variable]
Remove the unused variables.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The file Documentation/devicetree/bindings/mmc/mmc.txt is common for all
MMC host drivers. Use a generic MMC host reference instead of an SDHCI
left-over.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Rename esdhc local definitions with ESDHC_ rather than SDHCI_ prefix,
so that we can distinguish them from SDHCI core definitions from name.
A couple of bit fields are also changed use shift for consistency and
better readability.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
SDHCI_CTRL_D3CD is not a standard SDHCI_HOST_CONTROL, so there is no
need to check it in SDHCI_HOST_CONTROL write at all. Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
When commit 95a2482 (mmc: sdhci-esdhc-imx: add basic imx6q usdhc
support) works around host version issue on imx6q, it gets the
register address fixup "reg ^= 2" lost for imx25/35/51/53 esdhc.
Thus, the controller version on these SoCs is wrongly identified
as v1 while it's actually v2.
Add the address fixup back and take a different approach to correct
imx6q host version, so that the host version read gets back to work
for all SoCs.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
With the __devinit/__devexit attributes having been removed, this
__exitp attribute causes an unused function warning and should be
removed as well.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The original quirk was added in the change 'mmc: dw_mmc: add quirk to
indicate missing write protect line'. The original quirk was added at
a controller level even though each slot has its own write protect (so
the quirk should be at the slot level). A recent change (mmc: dw_mmc:
Add "disable-wp" device tree property) added a slot-level quirk and
support for the quirk directly to dw_mmc.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
On some SoCs (like exynos5250) you need to use an external GPIO for
write protect. Add support for wp-gpios to the core dw_mmc driver
since it could be useful across multiple SoCs.
With this change I am able to make use of the write protect for the
external SD slot on exynos5250-snow.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The exynos code claimed the write protect with devm_gpio_request() but
never did anything with it. That meant that anyone using a write
protect GPIO would effectively be write protected all the time.
The handling for wp-gpios belongs in the main dw_mmc driver and has
been moved there.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The next change will remove the code from the dw_mmc-exynos that added
the DW_MCI_QUIRK_NO_WRITE_PROTECT. Keep existing functionality of
having no write protect pin on smdk5250 by adding the disable-wp
property.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The "disable-wp" property is used to specify that a given SD card slot
doesn't have a concept of write protect. This eliminates the need for
special case code for SD slots that should never be write protected
(like a micro SD slot or a dev board).
The dw_mmc driver is special in needing to specify "disable-wp"
because the lack of a "wp-gpios" property means to use the special
purpose write protect line. On some other mmc devices the lack of
"wp-gpios" means that write protect should be disabled.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The right value is 54 according to eMMC 4.5 specification.
Signed-off-by: ZhangYi <yix.x.zhang@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Fixes the following warning when building with W=1 option:
drivers/mmc/host/mxs-mmc.c: In function 'mxs_mmc_adtc':
drivers/mmc/host/mxs-mmc.c:401:2: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
The warning happens because 'i' is used in 'for_each_sg(sgl, sg, sg_len, i)' and should be made unsigned.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Add an entry for MODULE_ALIAS().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
On many Marvell SoCs, the pins used for the SDIO interface are part of
the MPP pins, that are muxable pins. In order to get the muxing of
those pins correct, this commit integrates the mvsdio driver with the
pinctrl infrastructure by calling devm_pinctrl_get_select_default()
during ->probe().
Note that we permit this function to fail because not all Marvell
platforms have yet been fully converted to using the pinctrl
infrastructure.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mpl.ch>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Commit ee873fda3bec7c668407b837fc5519eb961fcd37 ("gianfar: Pack struct
gfar_priv_grp into three cachelines") moved the irq number and names
off into a separate struct and created accessors for them. However
it was never tested with NET_POLL enabled, and so some conversions
that were simply overlooked went undetected until now.
Make the netpoll ones also use the gfar_irq() accessors.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Cc: Jianhua Xie <jianhua.xie@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
and pmd_huge
Without this patch any kernel code that reads kernel memory in
non present kernel pte/pmds (as set by pageattr.c) will crash.
With this kernel code:
static struct page *crash_page;
static unsigned long *crash_address;
[..]
crash_page = alloc_pages(GFP_KERNEL, 9);
crash_address = page_address(crash_page);
if (set_memory_np((unsigned long)crash_address, 1))
printk("set_memory_np failure\n");
[..]
The kernel will crash if inside the "crash tool" one would try
to read the memory at the not present address.
crash> p crash_address
crash_address = $8 = (long unsigned int *) 0xffff88023c000000
crash> rd 0xffff88023c000000
[ *lockup* ]
The lockup happens because _PAGE_GLOBAL and _PAGE_PROTNONE
shares the same bit, and pageattr leaves _PAGE_GLOBAL set on a
kernel pte which is then mistaken as _PAGE_PROTNONE (so
pte_present returns true by mistake and the kernel fault then
gets confused and loops).
With THP the same can happen after we taught pmd_present to
check _PAGE_PROTNONE and _PAGE_PSE in commit
027ef6c87853b0a9df5317 ("mm: thp: fix pmd_present for
split_huge_page and PROT_NONE with THP"). THP has the same
problem with _PAGE_GLOBAL as the 4k pages, but it also has a
problem with _PAGE_PSE, which must be cleared too.
After the patch is applied copy_user correctly returns -EFAULT
and doesn't lockup anymore.
crash> p crash_address
crash_address = $9 = (long unsigned int *) 0xffff88023c000000
crash> rd 0xffff88023c000000
rd: read error: kernel virtual address: ffff88023c000000 type:
"64-bit KVADDR"
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: "H. Peter Anvin" <hpa@linux.intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
the PRESENT bit"
I got a report for a minor regression introduced by commit
027ef6c87853b ("mm: thp: fix pmd_present for split_huge_page and
PROT_NONE with THP").
So the problem is, pageattr creates kernel pagetables (pte and
pmds) that breaks pte_present/pmd_present and the patch above
exposed this invariant breakage for pmd_present.
The same problem already existed for the pte and pte_present and
it was fixed by commit 660a293ea9be709 ("x86, mm: Make
spurious_fault check explicitly check the PRESENT bit") (if it
wasn't for that commit, it wouldn't even be a regression). That
fix avoids the pagefault to use pte_present. I could follow
through by stopping using pmd_present/pmd_huge too.
However I think it's more robust to fix pageattr and to clear
the PSE/GLOBAL bitflags too in addition to the present bitflag.
So the kernel page fault can keep using the regular
pte_present/pmd_present/pmd_huge.
The confusion arises because _PAGE_GLOBAL and _PAGE_PROTNONE are
sharing the same bit, and in the pmd case we pretend _PAGE_PSE
to be set only in present pmds (to facilitate split_huge_page
final tlb flush).
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: "H. Peter Anvin" <hpa@linux.intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
If we aren't debugging per_cpu maps, the cpu's node is stored in
per_cpu variable numa_node. If `node' is NUMA_NO_NODE, it means
the caller wants to clear the cpu's node. So we should also
call set_cpu_numa_node() in this case.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Running the full dynticks cputime accounting with preemptible
kernel debugging trigger the following warning:
[ 4.488303] BUG: using smp_processor_id() in preemptible [00000000] code: init/1
[ 4.490971] caller is native_sched_clock+0x22/0x80
[ 4.493663] Pid: 1, comm: init Not tainted 3.8.0+ #13
[ 4.496376] Call Trace:
[ 4.498996] [<ffffffff813410eb>] debug_smp_processor_id+0xdb/0xf0
[ 4.501716] [<ffffffff8101e642>] native_sched_clock+0x22/0x80
[ 4.504434] [<ffffffff8101db99>] sched_clock+0x9/0x10
[ 4.507185] [<ffffffff81096ccd>] fetch_task_cputime+0xad/0x120
[ 4.509916] [<ffffffff81096dd5>] task_cputime+0x35/0x60
[ 4.512622] [<ffffffff810f146e>] acct_update_integrals+0x1e/0x40
[ 4.515372] [<ffffffff8117d2cf>] do_execve_common+0x4ff/0x5c0
[ 4.518117] [<ffffffff8117cf14>] ? do_execve_common+0x144/0x5c0
[ 4.520844] [<ffffffff81867a10>] ? rest_init+0x160/0x160
[ 4.523554] [<ffffffff8117d457>] do_execve+0x37/0x40
[ 4.526276] [<ffffffff810021a3>] run_init_process+0x23/0x30
[ 4.528953] [<ffffffff81867aac>] kernel_init+0x9c/0xf0
[ 4.531608] [<ffffffff8188356c>] ret_from_fork+0x7c/0xb0
We use sched_clock() to perform and fixup the cputime
accounting. However we are calling it with preemption enabled
from the read side, which trigger the bug above.
To fix this up, use local_clock() instead. It takes care of
preemption and also provide a more reliable clock source. This
is welcome for this kind of statistic that is widely relied on
in userspace.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Ingo Molnar <mingo@kernel.org>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Kevin Hilman <khilman@linaro.org>
Link: http://lkml.kernel.org/r/1361636925-22288-3-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Saw the following compiler warning on the linux-next tree:
kernel/itimer.c: In function 'set_cpu_itimer':
kernel/itimer.c:152:2: warning: passing argument 1 of 'timeval_to_cputime' discards 'const' qualifier from pointer target type [enabled by default]
...
timeval_to_cputime() is always passed a constant timeval in
argument, we need to teach the nsecs based cputime
implementation about that.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Kevin Hilman <khilman@linaro.org>
Link: http://lkml.kernel.org/r/1361636925-22288-2-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Kevin Hilman <khilman@linaro.org>
|
|
The Xtensa architecture provides a global register called THREADPTR
for the purpose of Thread Local Storage (TLS) support. This allows us
to use a fairly simple implementation, keeping the thread pointer in
the regset and simply saving and restoring it upon entering/exiting
the from user space.
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
This fixes the following build errors seen in the linux-next:
arch/xtensa/include/asm/checksum.h:247:2: error: implicit declaration of
function 'access_ok' [-Werror=implicit-function-declaration]
arch/xtensa/include/asm/checksum.h:247:16: error: 'VERIFY_WRITE' undeclared
(first use in this function)
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
Now that drivers/gpio/devres.c build does not depend on GPIOLIB do not
enable GENERIC_GPIO by default to fix the following build errors seen
in the linux-next:
include/asm-generic/gpio.h:270:2: error: implicit declaration of function
'__gpio_get_value' [-Werror=implicit-function-declaration]
include/asm-generic/gpio.h:276:2: error: implicit declaration of function
'__gpio_set_value' [-Werror=implicit-function-declaration]
include/linux/gpio.h:60:19: error: redefinition of 'gpio_cansleep'
include/linux/gpio.h:62:2: error: implicit declaration of function
'__gpio_cansleep' [-Werror=implicit-function-declaration]
include/linux/gpio.h:67:2: error: implicit declaration of function
'__gpio_to_irq' [-Werror=implicit-function-declaration]
drivers/gpio/devres.c:26:2: error: implicit declaration of function
'gpio_free' [-Werror=implicit-function-declaration]
drivers/gpio/devres.c:60:2: error: implicit declaration of function
'gpio_request' [-Werror=implicit-function-declaration]
drivers/gpio/devres.c:90:2: error: implicit declaration of function
'gpio_request_one' [-Werror=implicit-function-declaration]
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
Compute WindowBase and WindowMask registers correctly on ptrace calls.
Work done earlier by Maxim, Christian and Marc.
Signed-off-by: Marc Gauthier <marc@tensilica.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
Support call graph profiling.
Keep upper two bits of PC unchanged through backtrace rather than take
them from sp (a1). The stack pointer is usually in the same GB (same
upper 2 bits) as PC, but technically doesn't always have to be (and
might not in the future, when taking full advantage of MMU v3).
Signed-off-by: Dan Nicolaescu <dann@xtensa-linux.org>
Signed-off-by: Pete Delaney <piet@tensilica.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
Simdisk is a block device that maps to a file in the host file system.
It is usable for testing in the simulated environment, like xt-sim or
QEMU. Device binding to host file may be changed at runtime via proc
interface provided the device is not in use. Number of block devices
and initial binding to host files is controlled via kernel/module
parameters, with defaults specified in the kernel configuration.
Signed-off-by: Victor Prupis <vnp@tensilica.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
str[n]cmp functions return negative value if the first string is less
than the second, positive value if the first string is greater than the
second and zero if they are equal. This is important when these
functions are used for sorting/binary search.
With incorrect strcmp return value bsearch was always failing in the
find_symbol_in_section making it impossible to load any module.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
Provide arch_get_unmapped_area function aligning shared memory mapping
addresses to the biggest of the page size or the cache way size. That
guarantees that corresponding virtual addresses of shared mappings are
cached by the same cache sets.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
This fixes the following build error in the current linux-next:
include/linux/signal.h:261:2: error: unknown type name '__sigrestore_t'
make[2]: *** [arch/xtensa/kernel/asm-offsets.s] Error 1
make[1]: *** [prepare0] Error 2
make: *** [sub-make] Error 2
that appeared after 32dae82 'consolidate kernel-side struct sigaction declarations'
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
|
