| Age | Commit message (Collapse) | Author |
|---|
|
It adds VGA device in zx296718.dtsi, so that boards with VGA connector
can enable the support by changing 'status' in board DTS file.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
ls208xa supports another cpu idle state which is pw20 which saves
more power when cpu is idle.
It was implemented through psci firmware.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
ls1088a supports another cpu idle state which is ph20 which saves
more power when cpu is idle.
It was implemented through psci firmware.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
When adding the rk3399 sapphire som, two more of the recently removed
num-slots properties of dw-mmc nodes slipped in.
Remove them again.
Fixes: 8164a84cca12 ("arm64: dts: rockchip: Add support for rk3399 sapphire SOM")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add NAND controller node to LD11 and LD20. Neither of them supports
the CS1 line, so pinctrl is set up for a single CS line.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
enable tsadc module on RK3328 eavluation board
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
add thermal zone and dynamic CPU power coefficients for rk3328
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
add tsadc needed main information for rk3328 SoC.
50000Hz is the max clock rate supported by tsadc module.
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
BPi M64 has an AP6212 Wi-Fi/Bluetooth combo module, and the Wi-Fi SDIO
card is connected to the mmc1 controller.
The pwrseq of the mmc1 (used to reset the card) used to missing, and the
out-of-band interrupt line of the card is not specified.
Fix these issues for proper Wi-Fi support of BPi M64.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Banana Pi M64 board uses an AXP803 PMIC.
Enable the PMIC and its regulators.
As we have now proper regulators support, missing or dummy regulators
are changed to the correct ones.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Banana Pi M64 connects the USB host-only controller on A64 SoC to a USB
hub, which provided the two USB Type-A ports on the board.
Enable the USB host controller.
The OTG function of the Micro-USB port needs the drivevbus function of
the AXP803 driver implemented, so it's not enabled now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
On UniPhier platform, some DTSI files are shared between arm and arm64.
Recently, inclusion of DT material of different architectures has been
supported by the build system level. Use #include <arm/...>, which
will work without relying on the exact same hierarchy as the kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
To include dt-bindings headers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This patch switches to the stable UART bindings but also add the correct
gate clock to the non-AO UART nodes for GXBB and GXL SoCs.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the smd-edge node for the adsp, to allow SMD communication with the
ADSP.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This patch adds the SMP2P nodes for the modem.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add PM8994 RPM regulators with their min/max voltages to DB820c.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Adding required device node for couple of DWC3 controllers
present on msm8996 chipset to enable High speed and Super
speed USB support.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add required device node for QMP phy based 3-lane PCIe phy
present on msm8996 chipset to enable support for the same.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Adding required device node for USB3 QMP phy present on
msm8996 chipset to enable support for the same. This phy
provides super speed usb functionality for dwc3 controller
on msm8996.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Adding device node for QUSB2 phy and the required infrastructure
to enable support for the same. This phy is used by dwc3 controller
present on msm8996.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
The adv7533 on this board needs a cec clock. Hook it up in the dtsi
to enable CEC for the HDMI transmitters.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Replace the obsolete compatible string for Coresight programmable
replicator with the new one.
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Commit ed75d6a96905 ("arm64: dts: qcom: Collapse usb support into
one node") breaks host mode support on apq8016-sbc boards. This
is because the mux driver (tc7usb40mu) hasn't been merged.
Without that driver, we can't toggle the GPIO going to the mux to
route out the D+/D- lines to the USB hub that's on the board.
One solution would be to totally revert this change, but that
opens us up to other problems when two USB drivers are operating
the same hardware block at the same time. Let's modify the DT so
that the USB controller is always in host mode and connected to
the hub so that things like USB keyboards and mouses work. This
is the mode that most people prefer anyway with these devices. We
also delete the usb-switch node because the binding was never
accepted upstream.
In the future, we can add muxing support and then update the DT
to support both modes at runtime. Patches to support this are
already on the mailing list.
Fixes: ed75d6a96905 ("arm64: dts: qcom: Collapse usb support into one node")
Reported-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This patch add the i2s dt nodes for rk3328.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch adds Broadcom SBA-RAID DT nodes for Stingray SoC.
The Stingray SoC has total 32 SBA-RAID FlexRM rings and it has
8 CPUs so we create 8 SBA-RAID instances (one for each CPU).
This way Linux DMAENGINE will have one SBA-RAID DMA device for
each CPU.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
We have two instances of FlexRM on Stingray. One for SBA RAID
offload engine and another for SPU2 Crypto offload engine.
This patch adds FlexRM mailbox controller DT nodes for Stingray.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add DT nodes for SATA host controllers and SATA PHYs
on Stingray SoC
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
This patch adds DT node to enable BGMAC driver on Stingray
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Oza Oza <oza.oza@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
We have 8 instances of sp804 in Stingray SoC. Let's enable
it in Stingray DT.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Added MDIO multiplexer iproc DT node for Stingray, which contains
the child nodes of PCIe serdes, RGMII, SATA and USB phy MDIO slaves.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
This patch enables stats for CCN-502 interconnect on Stingray.
Signed-off-by: Velibor Markovski <velibor.markovski@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fix from Darren Hart:
"Fix loop preventing some platforms from waking up via the power button
in s2idle:
- intel-vbtn: match power button on press rather than release"
* tag 'platform-drivers-x86-v4.13-4' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: intel-vbtn: match power button on press rather than release
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"A large number of ext4 bug fixes and cleanups for v4.13"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix copy paste error in ext4_swap_extents()
ext4: fix overflow caused by missing cast in ext4_resize_fs()
ext4, project: expand inode extra size if possible
ext4: cleanup ext4_expand_extra_isize_ea()
ext4: restructure ext4_expand_extra_isize
ext4: fix forgetten xattr lock protection in ext4_expand_extra_isize
ext4: make xattr inode reads faster
ext4: inplace xattr block update fails to deduplicate blocks
ext4: remove unused mode parameter
ext4: fix warning about stack corruption
ext4: fix dir_nlink behaviour
ext4: silence array overflow warning
ext4: fix SEEK_HOLE/SEEK_DATA for blocksize < pagesize
ext4: release discard bio after sending discard commands
ext4: convert swap_inode_data() over to use swap() on most of the fields
ext4: error should be cleared if ea_inode isn't added to the cache
ext4: Don't clear SGID when inheriting ACLs
ext4: preserve i_mode if __ext4_set_acl() fails
ext4: remove unused metadata accounting variables
ext4: correct comment references to ext4_ext_direct_IO()
|
|
Pull MIPS fixes from Ralf Baechle:
"This fixes two build issues for ralink platforms, both due to missing
#includes which used to be included indirectly via other headers"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: ralink: mt7620: Add missing header
MIPS: ralink: Fix build error due to missing header
|
|
The latest change of compat_sys_sigpending in commit 8f13621abced
("sigpending(): move compat to native") has broken it in two ways.
First, it tries to write 4 bytes more than userspace expects:
sizeof(old_sigset_t) == sizeof(long) == 8 instead of
sizeof(compat_old_sigset_t) == sizeof(u32) == 4.
Second, on big endian architectures these bytes are being written in the
wrong order.
This bug was found by strace test suite.
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Inspired-by: Eugene Syromyatnikov <evgsyr@gmail.com>
Fixes: 8f13621abced ("sigpending(): move compat to native")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add support for the rk3399 excavator main board.
This board works in a combination with the sapphire SOM.
This board have been sold as the rk3399 evaluation board for commercial customers.
You can get more info from below link:
http://opensource.rock-chips.com/wiki_Excavator_sapphire_board
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add support for the rk3399 sapphire SOM board.
This board works in a combination with the excavator main board.
You can get more info from below link:
http://opensource.rock-chips.com/wiki_Excavator_sapphire_board
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add an hdmi node, and also add hdmi endpoints to vopb and vopl
output port nodes.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add an mipi node, and also add mipi endpoints to vopb and vopl
output port nodes.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add an edp node, and also add edp endpoints to vopb and vopl
output port nodes.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
1. add pd node for RK3399 Soc
2. create power domain tree
3. add qos node for domain
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add devicetree nodes for rk3399 VOP (Video Output Processors), and the
top level display-subsystem root node.
Later patches add endpoints (eDP, HDMI, MIPI, etc) that attach to the
VOPs' output ports.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add opp tables for cpu cluster0 and cluster1 by including
rk3399-opp.dtsi.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch adds basic OPP entries for RK3328 SoC.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This bug was found by a static code checker tool for copy paste
problems.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
