| Age | Commit message (Collapse) | Author |
|---|
|
Vivien Didelot says:
====================
net: dsa: mv88e6xxx: add PCL support
This small series implements the ethtool RXNFC operations in the
mv88e6xxx DSA driver to configure a port's Layer 2 Policy Control List
(PCL) supported by models such as 88E6352 and 88E6390 and equivalent.
This allows to configure a port to discard frames based on a configured
destination or source MAC address and an optional VLAN, with e.g.:
# ethtool --config-nfc lan1 flow-type ether src 00:11:22:33:44:55 action -1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the .get_rxnfc and .set_rxnfc DSA operations to configure
a port's Layer 2 Policy Control List (PCL) via ethtool.
Currently only dropping frames based on MAC Destination or Source
Address (including the option VLAN parameter) is supported.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a new .port_set_policy operation to configure a port's
Policy Control List, based on mapping such as DA, SA, Etype and so on.
Models similar to 88E6352 and 88E6390 are supported at the moment.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marvell has different values for the state of a MAC address,
depending on its multicast bit. This patch completes the definitions
for these states.
At the same time, use 0 which is intuitive enough and simplifies the
code a bit, instead of the UC or MC unused value.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All the popular filesystems need to grab the inode lock for buffered
writes. With io_uring punting buffered writes to async context, we
observe a lot of contention with all workers hamming this mutex.
For buffered writes, we generally don't need a lot of parallelism on
the submission side, as the flushing will take care of that for us.
Hence we don't need a deep queue on the write side, as long as we
can safely punt from the original submission context.
Add a workqueue with a limit of 2 that we can use for buffered writes.
This greatly improves the performance and efficiency of higher queue
depth buffered async writes with io_uring.
Reported-by: Andres Freund <andres@anarazel.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add a helper for queueing a request for async execution, in preparation
for optimizing it.
No functional change in this patch.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
It was recently discovered that the linux version of waitid is not a
superset of the other wait functions because it does not include support
for waiting for the current process group. This has two downsides:
1. An extra system call is needed to get the current process group.
2. After the current process group is received and before it is passed
to waitid a signal could arrive causing the current process group to change.
Inherent race-conditions as these make it impossible for userspace to
emulate this functionaly and thus violate async-signal safety
requirements for waitpid.
Arguments can be made for using a different choice of idtype and id
for this case but the BSDs already use this P_PGID and 0 to indicate
waiting for the current process's process group. So be nice to user
space programmers and don't introduce an unnecessary incompatibility.
Some people have noted that the posix description is that
waitpid will wait for the current process group, and that in
the presence of pthreads that process group can change. To get
clarity on this issue I looked at XNU, FreeBSD, and Luminos. All of
those flavors of unix waited for the current process group at the
time of call and as written could not adapt to the process group
changing after the call.
At one point Linux did adapt to the current process group changing but
that stopped in 161550d74c07 ("pid: sys_wait... fixes"). It has been
over 11 years since Linux has that behavior, no programs that fail
with the change in behavior have been reported, and I could not
find any other unix that does this. So I think it is safe to clarify
the definition of current process group, to current process group
at the time of the wait function.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Rich Felker <dalias@libc.org>
Cc: Alistair Francis <alistair23@gmail.com>
Cc: Zong Li <zongbox@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: Adhemerval Zanella <adhemerval.zanella@linaro.org>
Cc: GNU C Library <libc-alpha@sourceware.org>
Link: https://lore.kernel.org/r/20190814154400.6371-2-christian.brauner@ubuntu.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into HEAD
PPC KVM update for 5.4
- Some prep for extending the uses of the rmap array
- Various minor fixes
- Commits from the powerpc topic/ppc-kvm branch, which fix a problem
with interrupts arriving after free_irq, causing host hangs and crashes.
|
|
Manually generate the PDPTR reserved bit mask when explicitly loading
PDPTRs. The reserved bits that are being tracked by the MMU reflect the
current paging mode, which is unlikely to be PAE paging in the vast
majority of flows that use load_pdptrs(), e.g. CR0 and CR4 emulation,
__set_sregs(), etc... This can cause KVM to incorrectly signal a bad
PDPTR, or more likely, miss a reserved bit check and subsequently fail
a VM-Enter due to a bad VMCS.GUEST_PDPTR.
Add a one off helper to generate the reserved bits instead of sharing
code across the MMU's calculations and the PDPTR emulation. The PDPTR
reserved bits are basically set in stone, and pushing a helper into
the MMU's calculation adds unnecessary complexity without improving
readability.
Oppurtunistically fix/update the comment for load_pdptrs().
Note, the buggy commit also introduced a deliberate functional change,
"Also remove bit 5-6 from rsvd_bits_mask per latest SDM.", which was
effectively (and correctly) reverted by commit cd9ae5fe47df ("KVM: x86:
Fix page-tables reserved bits"). A bit of SDM archaeology shows that
the SDM from late 2008 had a bug (likely a copy+paste error) where it
listed bits 6:5 as AVL and A for PDPTEs used for 4k entries but reserved
for 2mb entries. I.e. the SDM contradicted itself, and bits 6:5 are and
always have been reserved.
Fixes: 20c466b56168d ("KVM: Use rsvd_bits_mask in load_pdptrs()")
Cc: stable@vger.kernel.org
Cc: Nadav Amit <nadav.amit@gmail.com>
Reported-by: Doug Reiland <doug.reiland@intel.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
We can easily route hardware interrupts directly into VM context when
they target the "Fixed" or "LowPriority" delivery modes.
However, on modes such as "SMI" or "Init", we need to go via KVM code
to actually put the vCPU into a different mode of operation, so we can
not post the interrupt
Add code in the VMX and SVM PI logic to explicitly refuse to establish
posted mappings for advanced IRQ deliver modes. This reflects the logic
in __apic_accept_irq() which also only ever passes Fixed and LowPriority
interrupts as posted interrupts into the guest.
This fixes a bug I have with code which configures real hardware to
inject virtual SMIs into my guest.
Signed-off-by: Alexander Graf <graf@amazon.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Wanpeng Li <wanpengli@tencent.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
For some applications that end up using a submit-and-wait type of
approach for certain batches of IO, we can make that a bit more
efficient by allowing the application to block for the last IO
submission. This prevents an async when we don't need it, as the
application will be blocking for the completion event(s) anyway.
Typical use cases are using the liburing
io_uring_submit_and_wait() API, or just using io_uring_enter()
doing both submissions and completions. As a specific example,
RocksDB doing MultiGet() is sped up quite a bit with this
change.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
2 bytes in MSB of register for clock status is zero during intermediate
state after changing status of sampling clock in models of TASCAM FireWire
series. The duration of this state differs depending on cases. During the
state, it's better to retry reading the register for current status of
the clock.
In current implementation, the intermediate state is checked only when
getting current sampling transmission frequency, then retry reading.
This care is required for the other operations to read the register.
This commit moves the codes of check and retry into helper function
commonly used for operations to read the register.
Fixes: e453df44f0d6 ("ALSA: firewire-tascam: add PCM functionality")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20190910135152.29800-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The return value of snd_tscm_stream_get_clock() is ignored. This commit
checks the value and handle error.
Fixes: e453df44f0d6 ("ALSA: firewire-tascam: add PCM functionality")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20190910135152.29800-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In ath9k_wmi_cmd, the allocated network buffer needs to be released
if timeout happens. Otherwise memory will be leaked.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In htc_config_pipe_credits, htc_setup_complete, and htc_connect_service
if time out happens, the allocated buffer needs to be released.
Otherwise there will be memory leak.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ath9k_reg_rmw_single do not need return value to cope with different
cases. And change functon return type to void.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
For sdio chip, if the rssi is not good, then it have some retry,
firmware will indicate the msdu list of a ppdu with a hole, it
means it lost the hole msdu, after the msdu retry from AP, the
hole msdu will indicate from firmware later. The hole msdu's PN
check will fail and the hole msdu will be dropped.
PN check fail example:
Sequence number PN number PN check status
3814 6101 success
3815 6102 success
3816 6103 success
3818 6105 success
3819 6106 success
3820 6107 success
3817 6104 fail
The correct logic is reorder the msdu list and then do PN check.
ieee80211_rx_reorder_ampdu of mac80211 will do the reorer logic
and then do PN check in ieee80211_rx_h_decrypt of mac80211.
example after reorder:
Sequence number PN number PN check status
3814 6101 success
3815 6102 success
3816 6103 success
3817 6104 success
3818 6105 success
3819 6106 success
3820 6107 success
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
For PMF case, the action,deauth,disassoc management need to encrypt
by hardware, it need to reserve 8 bytes for encryption, otherwise
the packet will be sent out with error format, then PMF case will
fail.
After add the 8 bytes, it will pass the PMF case.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull ipc regression fixes from Arnd Bergmann:
"Fix ipc regressions from y2038 patches
These are two regression fixes for bugs that got introduced during the
system call rework that went into linux-5.1 but only bisected and
fixed now:
- One patch affects semtimedop() on many of the less common 32-bit
architectures, this just needs a single-line bugfix.
- The other affects only sparc64 and has a slightly more invasive
workaround to apply the same change to sparc64 that was done to the
generic code used everywhere else"
* tag 'ipc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
ipc: fix sparc64 ipc() wrapper
ipc: fix semtimedop for generic 32-bit architectures
|
|
At the same time use the official naming for the knobs.
Tested on a Zenbook UX430UNR.
Signed-off-by: Kristian Klausen <kristian@klausen.dk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
The recent consolidation of the three permission checks introduced a subtle
regression. For timer_create() with a process wide timer it returns the
current task if the lookup through the PID which is encoded into the
clockid results in returning current.
That's broken because it does not validate whether the current task is the
group leader.
That was caused by the two different variants of permission checks:
- posix_cpu_timer_get() allowed access to the process wide clock when the
looked up task is current. That's not an issue because the process wide
clock is in the shared sighand.
- posix_cpu_timer_create() made sure that the looked up task is the group
leader.
Restore the previous state.
Note, that these permission checks are more than questionable, but that's
subject to follow up changes.
Fixes: 6ae40e3fdcd3 ("posix-cpu-timers: Provide task validation functions")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1909052314110.1902@nanos.tec.linutronix.de
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v5.4
Quite a big update this time around, particularly in the core
where we've had a lot of cleanups from Morimoto-san - there's
not much functional change but quite a bit of modernization
going on. We've also seen a lot of driver work, a lot of it
cleanups but also some particular drivers.
- Lots and lots of cleanups from Morimoto-san and Yue Haibing.
- Lots of cleanups and enhancements to the Freescale, sunxi dnd
Intel rivers.
- Initial Sound Open Firmware suppot for i.MX8.
- Removal of w90x900 and nuc900 drivers as the platforms are
being removed.
- New support for Cirrus Logic CS47L15 and CS47L92, Freescale
i.MX 7ULP and 8MQ, Meson G12A and NXP UDA1334
|
|
It is not used outside gpiolib-acpi.c module, so there is no need to
export it.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20190904172624.GA76617@dtor-ws
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We should only try to execute fallback quirks handling when previous
call returned -ENOENT, and not when we did not get -EPROBE_DEFER.
The other errors should be treated as hard errors: we did find the GPIO
description, but for some reason we failed to handle it properly.
The fallbacks should only be executed when previous handlers returned
-ENOENT, which means the mapping/description was not found.
Also let's remove the explicit deferral handling when iterating through
GPIO suffixes: it is not needed anymore as we will not be calling
fallbacks for anything but -ENOENT.
Fixes: df451f83e1fc ("gpio: of: fix Freescale SPI CS quirk handling")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20190903231856.GA165165@dtor-ws
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commit 3bd7f6589f67 ("spi: bcm2835: Overcome sglist entry length
limitation") amended the BCM2835 SPI driver with support for DMA
transfers whose buffers are not aligned to 4 bytes and require more than
one sglist entry.
When testing this feature with upcoming commits to speed up TX-only and
RX-only transfers, I noticed that SPI transmission sometimes breaks.
A function introduced by the commit, bcm2835_spi_transfer_prologue(),
performs one or two PIO transmissions as a prologue to the actual DMA
transmission. It turns out that the breakage goes away if the DONE bit
in the CS register is set when ending such a PIO transmission.
The DONE bit signifies emptiness of the TX FIFO. According to the spec,
the bit is of type RO, so writing it should never have any effect.
Perhaps the spec is wrong and the bit is actually of type RW1C.
E.g. the I2C controller on the BCM2835 does have an RW1C DONE bit which
needs to be cleared by the driver. Another, possibly more likely
explanation is that it's a hardware erratum since the issue does not
occur consistently.
Either way, amend bcm2835_spi_transfer_prologue() to always write the
DONE bit.
Usually a transmission is ended by bcm2835_spi_reset_hw(). If the
transmission was successful, the TX FIFO is empty and thus the DONE bit
is set when bcm2835_spi_reset_hw() reads the CS register. The bit is
then written back to the register, so we happen to do the right thing.
However if DONE is not set, e.g. because transmission is aborted with
a non-empty TX FIFO, the bit won't be written by bcm2835_spi_reset_hw()
and it seems possible that transmission might subsequently break. To be
on the safe side, likewise amend bcm2835_spi_reset_hw() to always write
the bit.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Link: https://lore.kernel.org/r/edb004dff4af6106f6bfcb89e1a96391e96eb857.1564825752.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into fixes
gpio: fixes for v5.4
- fix a memory leak in gpio-mockup
- fix two flag validation bugs in gpiolib's character device ioctl()'s
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into devel
intel-gpio for v5.4-1
The clean up of IRQ chip initialization has been done in few drivers.
Stale record in MAINTAINERS database is removed.
The following is an automated git shortlog grouped by driver:
intel-mid:
- Pass irqchip when adding gpiochip
- MAINTAINERS: Remove stale record for gpio-intel-mid.c
lynxpoint:
- Pass irqchip when adding gpiochip
merrifield:
- Pass irqchip when adding gpiochip
pch:
- Use dev_get_drvdata
|
|
Pro5 SoC has same scheme of USB3 VBUS as Pro4, so the data for Pro5 is
equivalent to Pro4.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1568080304-1572-1-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This adds the documentation to the compatible regulator-fixed-clock.
This binding is a special binding of regulator-fixed and adds the
ability to add a clock to regulator-fixed, so the regulator can be
enabled and disabled with that clock. If the special compatible
regulator-fixed-clock is used it is mandatory to supply a clock.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20190910062103.39641-4-philippe.schenker@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This commit adds the possibility to choose the compatible
"regulator-fixed-clock" in devicetree.
This is a special regulator-fixed that has to have a clock, from which
the regulator gets switched on and off.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Link: https://lore.kernel.org/r/20190910062103.39641-2-philippe.schenker@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The value under 's2mps11->ext_control_gpiod[i]' is assigned to local
variable and used in probe in one place before. Use it consistently
later so code will be easier to read.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20190909155723.24734-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Don't populate the array modes on the stack but instead make it
static const. Makes the object code smaller by 303 bytes.
Before:
text data bss dec hex filename
51240 5008 1312 57560 e0d8 mellanox/mlx4/en_ethtool.o
After:
text data bss dec hex filename
50937 5008 1312 57257 dfa9 mellanox/mlx4/en_ethtool.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent at the end.
In fact, NLMSG_DONE is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: 949f1e39a617 ("bridge: mdb: notify on router port add and del")
CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 1c2977c09499 ("net/ibmvnic: free reset work of removed device from queue")
adds a } without corresponding { causing build break.
Fixes: 1c2977c09499 ("net/ibmvnic: free reset work of removed device from queue")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Reviewed-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2019-09-09
This series contains a variety of cold and hot savoury changes to Intel
drivers. Some of the fixes could be considered for stable even though
the author did not request it.
Hulk Robert cleans up (i.e. removes) a function that has no caller for
the iavf driver.
Radoslaw fixes an issue when there is no link in the VM after the
hypervisor is restored from a low-power state due to the driver not
properly restoring features in the device that had been disabled during
the suspension for ixgbevf.
Kai-Heng Feng modified e1000e to use mod_delayed_work() to help resolve
a hot plug speed detection issue by adding a deterministic 1 second
delay before running watchdog task after an interrupt.
Sasha moves functions around to avoid forward declarations, since the
forward declarations are not necessary for these static functions in
igc. Also added a check for igc during driver probe to validate the NVM
checksum. Cleaned up code defines that were not being used in the igc
driver. Adds support for IP generic transmit checksum offload in the
igc driver.
Updated the iavf kernel documentation by a developer with no life.
Jake provides another fm10k update to a local variable for ease of code
readability.
Mitch fixes the iavf driver to allow the VF to override the MAC address
set by the host, if the VF is in "trusted" mode.
Mauro S. M. Rodrigues provides several changes for i40e driver, first
with resolving hw_dbg usage and referencing a i40e_hw attribute. Also
implemented a debug macro using pr_debug, since the use of netdev_dbg
could cause a NULL pointer dereference during probe. Finally cleaned up
code that is no longer used or needed.
Firo Yang provides a change in the ixgbe driver to ensure we sync the
first fragment unconditionally to help resolve an issue seen in the XEN
environment when the upper network stack could receive an incomplete
network packet.
Mariusz adds a missing device to the i40e PCI table in the driver.
v2: Mauro S. M. Rodrigues updated patches 10 & 11 of the series based on
feedback from Jakub Kicinski. Also updated patch 13 description so
that the "Fixes:" tag was no wrapped.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the build user has the CFLAGS variable set in their environment,
objtool blindly appends to it, which can cause unexpected behavior.
Clobber CFLAGS to ensure consistent objtool compilation behavior.
Reported-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Tested-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/83a276df209962e6058fcb6c615eef9d401c21bc.1567121311.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
processes as well
Add emulation (spoofing) of the SGDT, SIDT, and SMSW instructions for 64-bit
processes.
Wine users have encountered a number of 64-bit Windows games that use
these instructions (particularly SGDT), and were crashing when run on
UMIP-enabled systems.
Originally-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Signed-off-by: Brendan Shanks <bshanks@codeweavers.com>
Reviewed-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Reviewed-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190905232222.14900-1-bshanks@codeweavers.com
[ Minor edits: capitalization, added 'spoofing' wording. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
drm_gem_reservation_object_wait() returns 0 if it succeeds and -ETIME
if it timeouts, but lima driver assumed that 0 is error.
Cc: stable@vger.kernel.org
Fixes: a1d2a6339961e ("drm/lima: driver for ARM Mali4xx GPUs")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Qiang Yu <yuq825@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190908024800.23229-1-anarsoul@gmail.com
|
|
To support the link with drain, we need to do two parts.
There is an sqes:
0 1 2 3 4 5 6
+-----+-----+-----+-----+-----+-----+-----+
| N | L | L | L+D | N | N | N |
+-----+-----+-----+-----+-----+-----+-----+
First, we need to ensure that the io before the link is completed,
there is a easy way is set drain flag to the link list's head, so
all subsequent io will be inserted into the defer_list.
+-----+
(0) | N |
+-----+
| (2) (3) (4)
+-----+ +-----+ +-----+ +-----+
(1) | L+D | --> | L | --> | L+D | --> | N |
+-----+ +-----+ +-----+ +-----+
|
+-----+
(5) | N |
+-----+
|
+-----+
(6) | N |
+-----+
Second, ensure that the following IO will not be completed first,
an easy way is to create a mirror of drain io and insert it into
defer_list, in this way, as long as drain io is not processed, the
following io in the defer_list will not be actively process.
+-----+
(0) | N |
+-----+
| (2) (3) (4)
+-----+ +-----+ +-----+ +-----+
(1) | L+D | --> | L | --> | L+D | --> | N |
+-----+ +-----+ +-----+ +-----+
|
+-----+
('3) | D | <== This is a shadow of (3)
+-----+
|
+-----+
(5) | N |
+-----+
|
+-----+
(6) | N |
+-----+
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Sqo_thread will get sqring in batches, which will cause
ctx->cached_sq_head to be added in batches. if one of these
sqes is set with the DRAIN flag, then he will never get a
chance to process, and finally sqo_thread will not exit.
Fixes: de0617e4671 ("io_uring: add support for marking commands as draining")
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add all DaVinci boards to multi_v5_defconfig.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add modifications necessary to make davinci part of the ARM v5
multiplatform build.
Move the arch-specific configuration out of arch/arm/Kconfig and
into mach-davinci/Kconfig. Remove the sub-menu for DaVinci
implementations (they'll be visible directly under the system type.
Select all necessary options not already selected by ARCH_MULTI_V5.
Update davinci_all_defconfig. Explicitly include the mach-specific
headers in mach-davinci/Makefile.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add I40E_DEV_ID_10G_BASE_T_BC to i40e_pci_tbl
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add IP generic TX checksum offload functionality.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In Xen environment, if Xen-swiotlb is enabled, ixgbe driver
could possibly allocate a page, DMA memory buffer, for the first
fragment which is not suitable for Xen-swiotlb to do DMA operations.
Xen-swiotlb have to internally allocate another page for doing DMA
operations. This mechanism requires syncing the data from the internal
page to the page which ixgbe sends to upper network stack. However,
since commit f3213d932173 ("ixgbe: Update driver to make use of DMA
attributes in Rx path"), the unmap operation is performed with
DMA_ATTR_SKIP_CPU_SYNC. As a result, the sync is not performed.
Since the sync isn't performed, the upper network stack could receive
a incomplete network packet. By incomplete, it means the linear data
on the first fragment(between skb->head and skb->end) is invalid. So
we have to copy the data from the internal xen-swiotlb page to the page
which ixgbe sends to upper network stack through the sync operation.
More details from Alexander Duyck:
Specifically since we are mapping the frame with
DMA_ATTR_SKIP_CPU_SYNC we have to unmap with that as well. As a result
a sync is not performed on an unmap and must be done manually as we
skipped it for the first frag. As such we need to always sync before
possibly performing a page unmap operation.
Fixes: f3213d932173 ("ixgbe: Update driver to make use of DMA attributes in Rx path")
Signed-off-by: Firo Yang <firo.yang@suse.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Since commit
'5098850c9b9b ("i40e/i40evf: i40e_register.h updates")'
it is no longer possible to trigger an EMP Reset from debugfs, but it's
possible to request it either way, to end up with a bad reset request:
echo empr > /sys/kernel/debug/i40e/0002\:01\:00.1/command
i40e 0002:01:00.1: debugfs: forcing EMPR
i40e 0002:01:00.1: bad reset request 0x00010000
So let's remove this piece of code and show the available valid commands
as it is when any invalid command is issued.
Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There are several uses of hw_dbg in the code, producing no output. This
patch implements it using dev_debug.
Initially the intention was to implement it using netdev_dbg, analogously
to what is done in ixgbe for instance. That approach was avoided due to
some early usages of hw_dbg, like i40e_pf_reset, before the VSI structure
initialization causing NULL pointer dereference during the driver probe if
the debug messages were turned on as soon as the module is probed.
v2:
- Use dev_dbg instead of pr_debug, and take advantage of dev_name
instead of crafting pretty much the same device name locally as suggested
by Jakub Kicinski.
Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The device is officially called "Relative state of charge" (RSOC).
At the same time add the missing DEVID from the name.
Signed-off-by: Kristian Klausen <kristian@klausen.dk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
At the same time add a comment explaining what it is used for.
Signed-off-by: Kristian Klausen <kristian@klausen.dk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"This is obviouly very late, containing three small and simple driver
specific fixes.
The main one is the TWL fix, this fixes issues with cpufreq on the
PMICs used with BeagleBoard generation OMAP SoCs which had been broken
due to changes in the generic OPP code exposing a bug in the regulator
driver for these devices causing them to think that OPPs weren't
supported on the system.
Sorry about sending this so late, I hadn't registered that the TWL
issue manifested in cpufreq"
* tag 'regulator-fix-v5.3-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: twl: voltage lists for vdd1/2 on twl4030
regulator: act8945a-regulator: fix ldo register addresses in set_mode hook
regulator: slg51000: Fix a couple NULL vs IS_ERR() checks
|
