| Age | Commit message (Collapse) | Author |
|---|
|
Use skin temperature for maintaining temperature that is suitable
specifically for A500. Add CPU thermal zone that protects silicon.
All these changes don't make a significant difference, but it is a
more correct definition of thermal zones.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The verbose variant of the atmel,wakeup-method value was lost when patch
that added the property was merged because it conflicted with other patch,
re-add it for consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add power supplies to accelerometer node, for completeness.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The configuration of USB VBUS regulators was borrowed from downstream
kernel, which is incorrect because the corresponding GPIOs are connected
to PROX_EN (A501 3G model) and LED_EN pins in accordance to the board
schematics. USB works fine with both GPIOs being disabled, so remove the
bogus USB VBUS regulators. The USB VBUS of USB3 is supplied from the fixed
5v system regulator and device-mode USB1 doesn't have VBUS switches.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The TEMP_ALERT pin of LM90 temperature sensor is connected to Tegra SoC.
Add interrupt property to the temperature sensor for completeness.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The TEMP_ALERT pin of LM90 temperature sensor is connected to Tegra SoC.
Add interrupt property to the temperature sensor for completeness.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The TEMP_ALERT pin of LM90 temperature sensor is connected to Tegra SoC.
Add interrupt property to the temperature sensor for completeness.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The TEMP_ALERT pin of LM90 temperature sensor is connected to Tegra SoC.
Add interrupt property to the temperature sensor and enable it in pinmux,
for completeness.
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add the on-chip SoC thermal sensor to Tegra30 device-trees. Now CPU
temperature reporting and thermal throttling is available on all Tegra30
devices universally.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add initial version of device tree for Facebook Fuji (AST2600) BMC.
Fuji is Facebook's next generation switch platform with an AST2600 BMC
integrated for health monitoring purpose.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210805222818.8391-7-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Add initial version of device tree for Facebook Elbert (AST2600) BMC.
Elbert is Facebook's next generation switch platform with an AST2600 BMC
integrated for health monitoring purpose.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210805222818.8391-6-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Add initial version of device tree for Facebook Cloudripper (AST2600) BMC.
Cloudripper is Facebook's next generation switch platform with an AST2600
BMC integrated for health monitoring purpose.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210805222818.8391-5-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
This common descirption is included by all Facebook AST2600 Network BMC
platforms to minimize duplicated device entries across Facebook Network
BMC device trees.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210805222818.8391-4-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Simplify wedge400 flash layout by using the common layout defined in
"facebook-bmc-flash-layout-128.dtsi".
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210805222818.8391-3-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
This is the layout used by Facebook BMC systems. It describes the fixed
flash layout of a 128MB mtd device.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210805222818.8391-2-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Changes for am3 cpsw and SanCloud for v5.15
A series of changes to update am3 to use cpsw switch driver and
few updates to earlier SanCloud changes. The plan was to send the
cpsw switch driver changes earlier but looks like I never tagged
the mail thread in my inbox to apply for v5.15.
* tag 'omap-for-v5.15/dt-am3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-sancloud-bbe: Drop usb wifi comment
ARM: dts: am335x-sancloud-bbe: Fix missing pinctrl refs
ARM: dts: am335x-bone: switch to new cpsw switch drv
ARM: dts: am33xx: update ethernet aliases
ARM: dts: am335x-sl50: switch to new cpsw switch drv
ARM: dts: am335x-shc: switch to new cpsw switch drv
ARM: dts: am335x-phycore: switch to new cpsw switch drv
ARM: dts: am335x-pepper: switch to new cpsw switch drv
ARM: dts: am335x-pdu001: switch to new cpsw switch drv
ARM: dts: am335x-osd3358-sm-red: switch to new cpsw switch drv
ARM: dts: am335x-myirtech: switch to new cpsw switch drv
ARM: dts: am335x-moxa-uc: switch to new cpsw switch drv
ARM: dts: am335x-lxm: switch to new cpsw switch drv
ARM: dts: am335x-igep0033: switch to new cpsw switch drv
ARM: dts: am335x-cm-t335: switch to new cpsw switch drv
ARM: dts: am335x-chiliboard: switch to new cpsw switch drv
ARM: dts: am335x-nano: switch to new cpsw switch drv
ARM: dts: am335x-baltos: switch to new cpsw switch drv
Link: https://lore.kernel.org/r/pull-1628751694-126144@atomide.com-3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM64 changes for v5.15
1. Add CPU topology and cache information to Exynos DTSI files.
2. Correct GIC CPU interfaces address range on Exynos7.
* tag 'samsung-dt64-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: correct GIC CPU interfaces address range on Exynos7
arm64: dts: exynos: add CPU topology to Exynos5433
arm64: dts: exynos: Add cpu cache information to Exynos5433
arm64: dts: exynos: Add cpu cache information to Exynos7
Link: https://lore.kernel.org/r/20210811085128.30103-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.15
Add CPU topology to all Exynos DTSI files.
* tag 'samsung-dt-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: add CPU topology to Exynos5422
ARM: dts: exynos: add CPU topology to Exynos5420
ARM: dts: exynos: add CPU topology to Exynos5260
ARM: dts: exynos: add CPU topology to Exynos5250
ARM: dts: exynos: add CPU topology to Exynos4412
ARM: dts: exynos: add CPU topology to Exynos4210
ARM: dts: exynos: add CPU topology to Exynos3250
Link: https://lore.kernel.org/r/20210811085128.30103-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux into arm/dt
Amlogic ARM DT changes for v5.15:
- meson8: use a default higher default GPU clock to solve probe failure
- meson: add AIU audio controller and codec for ec100
- meson8b: fix pwm regulator supply property name
* tag 'amlogic-arm-dt-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
ARM: dts: meson8b: ec100: Fix the pwm regulator supply properties
ARM: dts: meson8b: mxq: Fix the pwm regulator supply properties
ARM: dts: meson8b: odroidc1: Fix the pwm regulator supply properties
ARM: dts: meson8b: ec100: wire up the RT5640 audio codec
ARM: dts: meson: Add the AIU audio controller
ARM: dts: meson8: Use a higher default GPU clock frequency
Link: https://lore.kernel.org/r/87519792-c9e7-76a6-5db5-0e955286b564@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux into arm/dt
Amlogic ARM64 DT changes for v5.15:
- nanoki-k2: enable bluetooth
- khadas vim & vim2: improve wifi
* tag 'amlogic-arm64-dt-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
arm64: dts: meson: improve gxm-khadas-vim2 wifi
arm64: dts: meson: improve gxl-s905x-khadas-vim wifi
arm64: dts: meson-gxbb: nanopi-k2: Enable Bluetooth
Link: https://lore.kernel.org/r/032895d9-62b6-6c9e-b04b-9c3d316f27ec@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux into arm/dt
Devicetree changes for TI K3 platforms for v5.15 merge window:
* New features:
- AM64 adds pwm and ecap capability
* tag 'ti-k3-dt-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux:
arm64: dts: ti: k3-am642-sk: Add pwm nodes
arm64: dts: ti: k3-am642-evm: Add pwm nodes
arm64: dts: ti: k3-am64-main: Add ecap pwm nodes
arm64: dts: ti: k3-am64-main: Add epwm nodes
Link: https://lore.kernel.org/r/20210809130631.pfvntcichsyeekbo@festive
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/dt
MT8173:
- Add regulator for MFG_ASYNC power domain
- Use alias for MMC to get fixed numbers
MT8183:
- Use alia for MMC to get fixed numbers
- Add optional event number for Global Comman Engine
* tag 'v5.14-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
dt-bindings: mediatek: Add optional mediatek,gce-events property
arm64: dts: mt8183: add mediatek,gce-events in mutex
arm64: dts: mediatek: mt8173: Add domain supply for mfg_async
arm64: dts: mt8173: elm: Use aliases to mmc nodes
arm64: dts: mt8183: kukui: Use aliases to mmc nodes
Link: https://lore.kernel.org/r/26c4026a-9f26-d5a3-c30f-439120a4eaa0@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/dt
Increase trip point on MT7623
* tag 'v5.14-next-dts32' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm: dts: mt7623: increase passive cooling trip
Link: https://lore.kernel.org/r/289ded1c-dae7-54ef-6b56-9433bfcaf9de@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt
IXP4xx DTS file updates for the v5.15 kernel cycle:
- Fix up some (non-urgent) IRQ flags for the PCI buses.
- Add the second UART to the generic ixp4xx.dtsi
- Make use of the new expansion bus driver in all device
trees with e.g. flash memory on the expansion bus.
- Adds the CF card slot to the Gateworks GW2358.
- Add new device trees for:
- Iomega NAS 100D
- D-Link DSM-G600
- Netgear WG302v2
- Arcom Vulcan
- Gateworks Avila GW2348
- Intel IXPD425 and siblings
- Coyote and IXDPG425
- Linksys WRV54G
* tag 'ixp4xx-dts-arm-soc-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: ixp4xx: Add a devicetree for Freecom FSG-3
ARM: dts: ixp4xx: Add devicetree for Linksys WRV54G
ARM: dts: ixp4xx: Add device trees for Coyote and IXDPG425
ARM: dts: ixp4xx: Add Intel IXDP425 etc reference designs
ARM: dts: ixp4xx: Add CF to GW2358
ARM: dts: ixp4xx: Add Gateworks Avila GW2348 device tree
ARM: dts: ixp4xx: Add Arcom Vulcan device tree
ARM: dts: ixp4xx: Add devicetree for Netgear WG302v2
ARM: dts: ixp4xx: Use the expansion bus
ARM: dts: ixp4xx: Add second UART
ARM: dts: ixp4xx: Add devicetree for D-Link DSM-G600 rev A
ARM: dts: ixp4xx: Move EPBX100 flash to external bus node
ARM: dts: ixp4xx: Add devicetree for Iomega NAS 100D
ARM: dts: ixp4xx: Fix up bad interrupt flags
Link: https://lore.kernel.org/r/CACRpkdY19AvWT--OcmEKbwFue_EcThVs7uZeHkzORten7xj-RA@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT for v5.15, round 1
Highlights:
----------
-MPU:
- ST boards:
- Add coporcessor detach mailbox on ED and DKx boards
- Fix dtbs_check SAI warnings
- DH boards:
-Fix some dtbs_check warnings: usb, backlight, hdmi
* tag 'stm32-dt-for-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: Update AV96 adv7513 node per dtbs_check
ARM: dts: stm32: Set {bitclock,frame}-master phandles on ST DKx
ARM: dts: stm32: Add coprocessor detach mbox on stm32mp15x-dkx boards
ARM: dts: stm32: Add coprocessor detach mbox on stm32mp157c-ed1 board
ARM: dts: stm32: Add usbphyc_port1 supply on DHCOM SoM
ARM: dts: stm32: Add backlight and panel supply on DHCOM SoM
ARM: dts: stm32: Set {bitclock,frame}-master phandles on DHCOM SoM
ARM: dts: stm32: Fix touchscreen IRQ line assignment on DHCOM
ARM: dts: stm32: Disable LAN8710 EDPD on DHCOM
ARM: dts: stm32: Prefer HW RTC on DHCOM SoM
Link: https://lore.kernel.org/r/e4f0bea3-4065-38d5-f1b2-007e4094c4a8@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into arm/dt
Highlights:
-----------
- Introduce 4KOpen STiH418-b2264 board
- Remove clk_ignore_unused from STi boards DT
- Remove clock-output-names and clk_critical properties
- Update some clock compatible
* tag 'sti-dt-for-v5.15-round1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: sti: remove clk_ignore_unused from bootargs for stih410-b2260
ARM: dts: sti: remove clk_ignore_unused from bootargs for stih418-b2199
ARM: dts: sti: remove clk_ignore_unused from bootargs for stih410-b2120
ARM: dts: sti: remove clk_ignore_unused from bootargs for stih407-b2120
ARM: dts: sti: Introduce 4KOpen (stih418-b2264) board
ARM: dts: sti: add the thermal sensor node within stih418
ARM: dts: sti: disable rng11 on the stih418 platform
ARM: dts: sti: add the spinor controller node within stih407-family
ARM: dts: sti: update clkgen-fsyn entries in stih418-clock
ARM: dts: sti: update clkgen-fsyn entries in stih410-clock
ARM: dts: sti: update clkgen-fsyn entries in stih407-clock
ARM: dts: sti: update clkgen-pll entries in stih418-clock
ARM: dts: sti: update clkgen-pll entries in stih410-clock
ARM: dts: sti: update clkgen-pll entries in stih407-clock
ARM: dts: sti: update flexgen compatible within stih410-clock
ARM: dts: sti: update flexgen compatible within stih407-clock
ARM: dts: sti: update flexgen compatible within stih418-clock
Link: https://lore.kernel.org/r/1d95209f-9cb4-47a3-2696-7a93df7cdc05@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Devicetree changes for omaps for v5.15
Devicetree changes for omaps to configure more devices, and
add support for new SoC variants and devices:
- Add add gpio-line-names for am335x-boneblue
- Add support for dra762 abz package
- Two patches for McASP support on omap4
- Three patches to add support for am335x-sancloud-bbe-lite
- A series of changes to configure PRUSS for am3/4/5
* tag 'omap-for-v5.15/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am57xx: Add PRUSS MDIO controller nodes
ARM: dts: am57xx: Add PRU-ICSS nodes
ARM: dts: am4372: Add PRUSS MDIO controller node
ARM: dts: am4372: Add the PRU-ICSS0 DT node
ARM: dts: am4372: Add the PRU-ICSS1 DT node
ARM: dts: am335x-icev2: Enable PRU-ICSS module
ARM: dts: am335x-evmsk: Enable PRU-ICSS module
ARM: dts: am335x-evm: Enable PRU-ICSS module
ARM: dts: am335x-bone-common: Enable PRU-ICSS node
ARM: dts: am33xx-l4: Add PRUSS MDIO controller node
ARM: dts: am33xx-l4: Add PRUSS node
ARM: dts: am335x-sancloud-bbe-lite: New devicetree
ARM: dts: am335x-sancloud-bbe: Extract common code
ARM: dts: am335x-boneblack: Extract HDMI config
ARM: dts: omap4-l4-abe: Add McASP configuration
ARM: dts: omap4-l4-abe: Correct sidle modes for McASP
ARM: dts: Add support for dra762 abz package
ARM: dts: am335x-boneblue: add gpio-line-names
Link: https://lore.kernel.org/r/pull-1628153040-834155@atomide.com-3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The device tree node for the XUDC (USB device mode controller) is
missing the interconnects property that describes the path to memory for
the controller. Add the property so that the things like the DMA mask
can be set by the operating system.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Jetson TX2 NX Developer Kit is very similar to the Jetson Nano, but
uses the more powerful Tegra186 SoC.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
These PWMs can be used for fan or LED backlight control. Add the device
tree nodes for all existing controllers found on Tegra186 SoCs. None of
these are enabled by default, which is left for the board DTS files to
do when necessary.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Jetson TX2 NX Developer Kit is the same form factor as Jetson Nano,
but uses the more powerful Tegra186 SoC for added performance.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Now the I2C device nodes in all DTS files have gained "interrupt-names"
properties, the "interrupt-names" property can be made required.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/da8d1973dcd419d8d9c8c662ee614952f3a6969e.1626267422.git.geert+renesas@glider.be
|
|
Add "interrupt-names" properties to the I2C device nodes, to make it
easier to review the interrupt mappings.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/d35ba11bd705e3c728f94ff0414ac6ae1156244f.1626267422.git.geert+renesas@glider.be
|
|
Add "interrupt-names" properties to the I2C device nodes of the RZ/A1H
and RZ/A2M DTS files, to make it easier to review the interrupt mappings.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/7a073439e37f6672e4809af0a2ee9cd4ac820ec6.1626267422.git.geert+renesas@glider.be
|
|
The Renesas RZ/A and RZ/G2L I2C Bus Interface has no less than 8
interrupts. Hence document the "interrupt-names" property, to make it
easier to review the interrupt mappings in DTS files.
Note that this property cannot be made required yet, as the RIIC nodes
in all DTS files lack the property.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/a81d0e14e395f297666e8c3a8ce3e292d2606a65.1626267422.git.geert+renesas@glider.be
|
|
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add CANFD node to R9A07G044 (RZ/G2L) SoC DTSI.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210727133022.634-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Renesas RZ/G2L DT Binding Definitions Update
Missing definition for the P0_DIV2 core clock on the Renesas RZ/G2L
(R9A07G044) SoC, shared by driver and DT source files.
|
|
Add ADC node to R9A07G044 (RZ/G2L) SoC DTSI.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210804202118.25745-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add GPIO/pinctrl node to R9A07G044 (RZ/G2L) SoC DTSI.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210727112328.18809-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add initial support limited to HDMI i2s and SPDIF (LPCM).
Tested-by: Oleg Ivanov <150balbes@yandex.ru>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210804140258.4666-1-christianshewitt@gmail.com
|
|
Add initial support limited to HDMI i2s and SPDIF (LPCM).
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210804140029.4445-1-christianshewitt@gmail.com
|
|
The wifi chip on USB port 4 may not be present on all BBE variants.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
pinctrl settings for the USB hub, barometer & accelerometer need to be
referenced from the relevant nodes to work.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The GIC-400 CPU interfaces address range is defined as 0x2000-0x3FFF (by
ARM).
Reported-by: Sam Protsenko <semen.protsenko@linaro.org>
Reported-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Fixes: b9024cbc937d ("arm64: dts: Add initial device tree support for exynos7")
Link: https://lore.kernel.org/r/20210805072110.4730-1-krzysztof.kozlowski@canonical.com
|
