| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The regular "bump-in-the-middle" updates, containing mostly ASoC-
related fixes at this time. All changes are reasonably small.
A few entries are for ASoC and ALSA core parts (DAPM, PCM, topology)
for followups of the recent changes and potential buffer overflow by
snprintf(), while the rest are (both new and old) device-specific
fixes for Intel, meson, tas2562, rt1015, as well as the usual HD-audio
quirks"
* tag 'sound-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (25 commits)
ALSA: sgio2audio: Remove usage of dropped hw_params/hw_free functions
ALSA: hda/realtek - Enable the headset of ASUS B9450FA with ALC294
ALSA: hda/realtek - Fix silent output on Gigabyte X570 Aorus Master
ALSA: hda/realtek - Add Headset Button supported for ThinkPad X1
ALSA: hda/realtek - Add Headset Mic supported
ASoC: wm8741: Fix typo in Kconfig prompt
ASoC: stm32: sai: manage rebind issue
ASoC: SOF: Fix snd_sof_ipc_stream_posn()
ASoC: rt1015: modify pre-divider for sysclk
ASoC: rt1015: add operation callback function for rt1015_dai[]
ASoC: soc-component: tidyup snd_soc_pcm_component_sync_stop()
ASoC: dapm: Correct DAPM handling of active widgets during shutdown
ASoC: tas2562: Fix sample rate error message
ASoC: Intel: Skylake: Fix available clock counter incrementation
ASoC: soc-pcm/soc-compress: don't use snd_soc_dapm_stream_stop()
ASoC: meson: g12a: add tohdmitx reset
ASoC: pcm512x: Fix unbalanced regulator enable call in probe error path
ASoC: soc-core: fix for_rtd_codec_dai_rollback() macro
ASoC: topology: Fix memleak in soc_tplg_manifest_load()
ASoC: topology: Fix memleak in soc_tplg_link_elems_load()
...
|
|
Interrupts should not be specified by interrupt line but by
gpio parent and reference.
Fixes: 73f2b940474d ("MIPS: CI20: DTS: Add I2C nodes")
Cc: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
There is a ACT8600 on the CI20 board and the bindings of the
ACT8865 driver have changed without updating the CI20 device
tree. Therefore the PMU can not be probed successfully and
is running in power-on reset state.
Fix DT to match the latest act8865-regulator bindings.
Fixes: 73f2b940474d ("MIPS: CI20: DTS: Add I2C nodes")
Cc: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Mark mips_ejtag_fdc_encode() methods switch-case-4 as expecting to
fall through.
This patch fixes the following warning:
drivers/tty/mips_ejtag_fdc.c: In function ‘mips_ejtag_fdc_encode’:
drivers/tty/mips_ejtag_fdc.c:245:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
word.word &= 0x00ffffff;
~~~~~~~~~~^~~~~~~~~~~~~
drivers/tty/mips_ejtag_fdc.c:246:2: note: here
case 3:
^~~~
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Link: https://lore.kernel.org/r/20200306124913.151A68030792@mail.baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many embedded boards have a disconnected TTL level serial which can
generate some garbage that can lead to spurious false sysrq detects.
Currently, sysrq can be either completely disabled for serial console
or always disabled (with CONFIG_MAGIC_SYSRQ_SERIAL), since
commit 732dbf3a6104 ("serial: do not accept sysrq characters via serial port")
At Arista, we have such boards that can generate BREAK and random
garbage. While disabling sysrq for serial console would solve
the problem with spurious false sysrq triggers, it's also desirable
to have a way to enable sysrq back.
As a measure of balance between on and off options, add
MAGIC_SYSRQ_SERIAL_SEQUENCE which is a string sequence that can enable
sysrq if it follows BREAK on a serial line. The longer the string - the
less likely it may be in the garbage.
Having the way to enable sysrq was beneficial to debug lockups with
a manual investigation in field and on the other side preventing false
sysrq detections.
Based-on-patch-by: Vasiliy Khoruzhick <vasilykh@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20200302175135.269397-3-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many embedded boards have a disconnected TTL level serial which can
generate some garbage that can lead to spurious false sysrq detects.
Currently, sysrq can be either completely disabled for serial console
or always disabled (with CONFIG_MAGIC_SYSRQ_SERIAL), since
commit 732dbf3a6104 ("serial: do not accept sysrq characters via serial port")
At Arista, we have such boards that can generate BREAK and random
garbage. While disabling sysrq for serial console would solve
the problem with spurious false sysrq triggers, it's also desirable
to have a way to enable sysrq back.
Having the way to enable sysrq was beneficial to debug lockups with
a manual investigation in field and on the other side preventing false
sysrq detections.
As a preparation to add sysrq_toggle_support() call into uart,
remove a private copy of sysrq_enabled from sysctl - it should reflect
the actual status of sysrq.
Furthermore, the private copy isn't correct already in case
sysrq_always_enabled is true. So, remove __sysrq_enabled and use a
getter-helper sysrq_mask() to check sysrq_key_op enabled status.
Cc: Iurii Zaikin <yzaikin@google.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20200302175135.269397-2-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit e490c9144cfa ("tty: Add software emulated RS485 support for 8250")
introduced support to use RTS as an rs485 Transmit Enable signal if data
is transmitted through the tty layer.
Console messages bypass the tty layer and instead are emitted via
serial8250_console_write(). Amend that function to drive RTS as well,
allowing for a console on rs485 ports.
Note that serial8250_console_write() may be called concurrently to the
tty layer accessing the port. The two protect their accesses with the
port lock, but serial8250_console_write() may find RTS still being
asserted by the tty layer, in which case it shouldn't be deasserted
after the console message has been printed. Recognize such situations
by checking the em485->tx_stopped flag.
If a delay_rts_before_send or delay_rts_after_send has been specified,
serial8250_console_write() busy-waits for its duration. Optimizations
for those wait times are conceivable: E.g. if RTS is already asserted,
we could check whether em485->start_tx_timer is active and wait only
for the remaining expire time. But this would require calling into
the hrtimer infrastructure, which involves acquiring locks and
potentially reprogramming timer hardware. Such operations seem too
risky in the context of console printout, which needs to work even when
the kernel has crashed and emits a BUG splat. So I've gone with a
simplistic solution which just always waits for the full delay.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/65edffce4670a19e598015c03cbe46f1ffd93e43.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Amend 8250_bcm2835aux.c to support rs485 as introduced for 8250_omap.c
by commit e490c9144cfa ("tty: Add software emulated RS485 support for
8250").
The bcm2835aux differs from omap chips by inverting the meaning of RTS
in the MCR register: If the bit is clear, RTS is high. With omap, it's
apparently the other way round.
Moreover, omap achieves half-duplex mode by disabling the UART_IER_RDI
interrupt and clearing the RX FIFO when TX stops. This approach doesn't
work on bcm2835aux because the UART_LSR_DR bit is set even when
UART_IER_RDI is disabled. Consequently, serial8250_handle_irq() invokes
serial8250_rx_chars() to empty the FIFO and characters are received even
though the user requested half-duplex. Solve by disabling the receiver
using the non-standard CNTL register.
Cache that register in the driver's private data for performance. Set
the private data pointer before calling serial8250_register_8250_port()
to prevent a null pointer deref in case one of the rs485 callbacks is
invoked immediately after port registration.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/dd86460e20a8f979b7272a0bde73640312b902b1.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit e490c9144cfa ("tty: Add software emulated RS485 support for 8250")
introduced support to use RTS as an rs485 Transmit Enable signal.
So far the only drivers taking advantage of it are 8250_omap.c and
8250_of.c.
We're about to make use of the feature in 8250_bcm2835aux.c as well.
The bcm2835aux differs from omap chips by inverting the meaning of RTS
in the MCR register. Moreover, omap achieves half-duplex mode by
disabling the RX interrupt and clearing the RX FIFO when TX stops.
The bcm2835aux requires disabling the receiver instead.
Support these behavioral differences by generalizing the rs485 emulation:
Introduce ->rs485_start_tx() and ->rs485_stop_tx() callbacks in struct
uart_8250_port, provide generic implementations containing the existing
code and use them as callbacks in 8250_omap.c and 8250_of.c.
start_tx_rs485() is idempotent in that it recognizes whether RTS is
already asserted. Achieve the same by introducing a tx_stopped flag in
struct uart_8250_em485. This may even perform a little better on arches
where memory access is faster than mmio access.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/5ac0464ae4414708e723a1e0d52b0c1b2bd41b9b.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When rs485 transmission over an 8250 port stops, __stop_tx() assigns
active_timer = NULL before calling __stop_tx_rs485().
That function in turn either assigns active_timer = stop_tx_timer and
rearms the timer (in case a delay_rts_after_send needs to be observed)
or directly calls __do_stop_tx_rs485().
Move the assignment active_timer = NULL to __stop_tx_rs485() into the
branch which directly calls __do_stop_tx_rs485(), thereby avoiding a
duplicate assignment and simplifying the code.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/bca638405550eaf92f0c6060b553b687f35885e0.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Amend the generic ->rs485_config() callback to sanitize RTS polarity and
zero-fill the padding (in addition to the existing sanitization of the
RTS delays).
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/ff833721bc372d38678f289eb2a44dbf016d5203.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit e490c9144cfa ("tty: Add software emulated RS485 support for 8250")
introduced support to use RTS as an rs485 Transmit Enable signal.
Drivers opt in to the feature by calling serial8250_em485_init() from
their ->rs485_config() callback.
So far there are two drivers doing that, 8250_omap.c and 8250_of.c.
Both use an identical callback. We're about to add a third user of that
callback, therefore deduplicate it and move it to 8250_port.c.
Drivers now opt in to rs485 software emulation by assigning the generic
serial8250_rs485_config() callback introduced herein to their
.rs485_config struct member. This change allows unexporting
serial8250_em485_init() and declaring it static.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Cc: Heiko Schocher <hs@denx.de>
Link: https://lore.kernel.org/r/fcef63642dc4eae41ae7842d23747b2bf5d40285.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Retrieve rs485 devicetree properties on registration of 8250 ports in
case they are attached to an rs485 transceiver.
If the property "linux,rs485-enabled-at-boot-time" is present, invoke
the ->rs485_config() callback to immediately deassert RTS, thereby
ceasing control of the bus.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Giulio Benetti <giulio.benetti@micronovasrl.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/5908ea89b7f9da54872d6634b606d83db032297a.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
serial8250_do_set_mctrl() currently allows modifying the RTS modem
control line even when RTS is used as an rs485 Transmit Enable signal.
It is thus possible for user space to interfere with rs485 communication
by invoking a TIOCMSET ioctl().
Ignore such change requests and retain the current RTS polarity when in
rs485 mode. Note that serial8250_set_mctrl() is always called with
port->lock held, so there's no risk that RTS is changed concurrently.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/b1ce34ca9bc4d7bdc6e9852fcf30b1f4e37c8a80.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If a driver exposes early consoles with EARLYCON_DECLARE() and
OF_EARLYCON_DECLARE(), pefer the non-OF variant if the user specifies it
by
earlycon=<driver>,<options>
The rationale behind this is that some drivers register multiple setup
functions under the same driver name. Eg.
OF_EARLYCON_DECLARE(lpuart, "fsl,vf610-lpuart", lpuart_early_console_setup);
OF_EARLYCON_DECLARE(lpuart32, "fsl,ls1021a-lpuart", lpuart32_early_console_setup);
OF_EARLYCON_DECLARE(lpuart32, "fsl,imx7ulp-lpuart", lpuart32_imx_early_console_setup);
EARLYCON_DECLARE(lpuart, lpuart_early_console_setup);
EARLYCON_DECLARE(lpuart32, lpuart32_early_console_setup);
It depends on the order of the entries which console_setup() actually
gets called. To make things worse, I guess it also depends on the
compiler how these are ordered. Thus always prefer the EARLYCON_DECLARE()
ones.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200220174607.24285-1-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch corrects the SPDX License Identifier style in
header files related to tty serial drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200301204517.GA10368@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
perf top:
Tommi Rantala:
- Fix stdio interface input handling with glibc 2.28+.
perf bench:
Tommi Rantala:
- Restore thread count default to online CPU count in futex-wake bench.
perf jevents:
John Garry:
- Fix leak of mapfile memory.
perf diff:
Nick Desaulniers:
- Fix undefined string comparision spotted by clang's -Wstring-compare.
misc:
Ian Rogers:
- Fix off-by 1 relative directory includes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
rhashtable_lookup_get_insert_key doesn't have a parameter `data`. It
does have a parameter `key`, however.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.6
More fixes that have arrived since the merge window, spread out all
over. There's a few things like the operation callback addition for
rt1015 and the meson reset addition which add small new bits of
functionality to fix non-working systems, they're all very small and for
parts of newly added functionality.
|
|
pkaustub@cisco.com is bouncing, remove it.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These are a couple of read locks that should be write locks.
Fixes: fbb39807e9ae ("ionic: support sr-iov operations")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to commit 38f88c454042 ("bonding/alb: properly access headers
in bond_alb_xmit()"), we need to make sure arp header was pulled
in skb->head before blindly accessing it in rlb_arp_xmit().
Remove arp_pkt() private helper, since it is more readable/obvious
to have the following construct back to back :
if (!pskb_network_may_pull(skb, sizeof(*arp)))
return NULL;
arp = (struct arp_pkt *)skb_network_header(skb);
syzbot reported :
BUG: KMSAN: uninit-value in bond_slave_has_mac_rx include/net/bonding.h:704 [inline]
BUG: KMSAN: uninit-value in rlb_arp_xmit drivers/net/bonding/bond_alb.c:662 [inline]
BUG: KMSAN: uninit-value in bond_alb_xmit+0x575/0x25e0 drivers/net/bonding/bond_alb.c:1477
CPU: 0 PID: 12743 Comm: syz-executor.4 Not tainted 5.6.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x220 lib/dump_stack.c:118
kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118
__msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215
bond_slave_has_mac_rx include/net/bonding.h:704 [inline]
rlb_arp_xmit drivers/net/bonding/bond_alb.c:662 [inline]
bond_alb_xmit+0x575/0x25e0 drivers/net/bonding/bond_alb.c:1477
__bond_start_xmit drivers/net/bonding/bond_main.c:4257 [inline]
bond_start_xmit+0x85d/0x2f70 drivers/net/bonding/bond_main.c:4282
__netdev_start_xmit include/linux/netdevice.h:4524 [inline]
netdev_start_xmit include/linux/netdevice.h:4538 [inline]
xmit_one net/core/dev.c:3470 [inline]
dev_hard_start_xmit+0x531/0xab0 net/core/dev.c:3486
__dev_queue_xmit+0x37de/0x4220 net/core/dev.c:4063
dev_queue_xmit+0x4b/0x60 net/core/dev.c:4096
packet_snd net/packet/af_packet.c:2967 [inline]
packet_sendmsg+0x8347/0x93b0 net/packet/af_packet.c:2992
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg net/socket.c:672 [inline]
__sys_sendto+0xc1b/0xc50 net/socket.c:1998
__do_sys_sendto net/socket.c:2010 [inline]
__se_sys_sendto+0x107/0x130 net/socket.c:2006
__x64_sys_sendto+0x6e/0x90 net/socket.c:2006
do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x45c479
Code: ad b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fc77ffbbc78 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 00007fc77ffbc6d4 RCX: 000000000045c479
RDX: 000000000000000e RSI: 00000000200004c0 RDI: 0000000000000003
RBP: 000000000076bf20 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 0000000000000a04 R14: 00000000004cc7b0 R15: 000000000076bf2c
Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:144 [inline]
kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:127
kmsan_slab_alloc+0x8a/0xe0 mm/kmsan/kmsan_hooks.c:82
slab_alloc_node mm/slub.c:2793 [inline]
__kmalloc_node_track_caller+0xb40/0x1200 mm/slub.c:4401
__kmalloc_reserve net/core/skbuff.c:142 [inline]
__alloc_skb+0x2fd/0xac0 net/core/skbuff.c:210
alloc_skb include/linux/skbuff.h:1051 [inline]
alloc_skb_with_frags+0x18c/0xa70 net/core/skbuff.c:5766
sock_alloc_send_pskb+0xada/0xc60 net/core/sock.c:2242
packet_alloc_skb net/packet/af_packet.c:2815 [inline]
packet_snd net/packet/af_packet.c:2910 [inline]
packet_sendmsg+0x66a0/0x93b0 net/packet/af_packet.c:2992
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg net/socket.c:672 [inline]
__sys_sendto+0xc1b/0xc50 net/socket.c:1998
__do_sys_sendto net/socket.c:2010 [inline]
__se_sys_sendto+0x107/0x130 net/socket.c:2006
__x64_sys_sendto+0x6e/0x90 net/socket.c:2006
do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Madalin Bucur says:
====================
QorIQ DPAA FMan erratum A050385 workaround
Changes in v2:
- added CONFIG_DPAA_ERRATUM_A050385
- removed unnecessary parenthesis
- changed alignment defines to use only decimal values
The patch set implements the workaround for FMan erratum A050385:
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak; thus stopping further packet processing.
To reproduce this issue when the workaround is not applied, one
needs to ensure the FMan DMA transaction queue is already full
when a transaction split occurs so the system must be under high
traffic load (i.e. multiple ports at line rate). After the errata
occurs, the traffic stops. The only SoC impacted by this is the
LS1043A, the other ARM DPAA 1 SoC or the PPC DPAA 1 SoCs do not
have this erratum.
The FMAN internal queue can overflow when FMAN splits single
read or write transactions into multiple smaller transactions
such that more than 17 AXI transactions are in flight from FMAN
to interconnect. When the FMAN internal queue overflows, it can
stall further packet processing. The issue can occur with any one
of the following three conditions:
1. FMAN AXI transaction crosses 4K address boundary (Errata
A010022)
2. FMAN DMA address for an AXI transaction is not 16 byte
aligned, i.e. the last 4 bits of an address are non-zero
3. Scatter Gather (SG) frames have more than one SG buffer in
the SG list and any one of the buffers, except the last
buffer in the SG list has data size that is not a multiple
of 16 bytes, i.e., other than 16, 32, 48, 64, etc.
With any one of the above three conditions present, there is
likelihood of stalled FMAN packet processing, especially under
stress with multiple ports injecting line-rate traffic.
To avoid situations that stall FMAN packet processing, all of the
above three conditions must be avoided; therefore, configure the
system with the following rules:
1. Frame buffers must not span a 4KB address boundary, unless
the frame start address is 256 byte aligned
2. All FMAN DMA start addresses (for example, BMAN buffer
address, FD[address] + FD[offset]) are 16B aligned
3. SG table and buffer addresses are 16B aligned and the size
of SG buffers are multiple of 16 bytes, except for the last
SG buffer that can be of any size.
Additional workaround notes:
- Address alignment of 64 bytes is recommended for maximally
efficient system bus transactions (although 16 byte alignment is
sufficient to avoid the stall condition)
- To support frame sizes that are larger than 4K bytes, there are
two options:
1. Large single buffer frames that span a 4KB page boundary can
be converted into SG frames to avoid transaction splits at
the 4KB boundary,
2. Align the large single buffer to 256B address boundaries,
ensure that the frame address plus offset is 256B aligned.
- If software generated SG frames have buffers that are unaligned
and with random non-multiple of 16 byte lengths, before
transmitting such frames via FMAN, frames will need to be copied
into a new single buffer or multiple buffer SG frame that is
compliant with the three rules listed above.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Align buffers, data start, SG fragment length to avoid DMA splits.
These changes prevent the A050385 erratum to manifest itself:
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak; thus stopping further packet processing.
The FMAN internal queue can overflow when FMAN splits single
read or write transactions into multiple smaller transactions
such that more than 17 AXI transactions are in flight from FMAN
to interconnect. When the FMAN internal queue overflows, it can
stall further packet processing. The issue can occur with any one
of the following three conditions:
1. FMAN AXI transaction crosses 4K address boundary (Errata
A010022)
2. FMAN DMA address for an AXI transaction is not 16 byte
aligned, i.e. the last 4 bits of an address are non-zero
3. Scatter Gather (SG) frames have more than one SG buffer in
the SG list and any one of the buffers, except the last
buffer in the SG list has data size that is not a multiple
of 16 bytes, i.e., other than 16, 32, 48, 64, etc.
With any one of the above three conditions present, there is
likelihood of stalled FMAN packet processing, especially under
stress with multiple ports injecting line-rate traffic.
To avoid situations that stall FMAN packet processing, all of the
above three conditions must be avoided; therefore, configure the
system with the following rules:
1. Frame buffers must not span a 4KB address boundary, unless
the frame start address is 256 byte aligned
2. All FMAN DMA start addresses (for example, BMAN buffer
address, FD[address] + FD[offset]) are 16B aligned
3. SG table and buffer addresses are 16B aligned and the size
of SG buffers are multiple of 16 bytes, except for the last
SG buffer that can be of any size.
Additional workaround notes:
- Address alignment of 64 bytes is recommended for maximally
efficient system bus transactions (although 16 byte alignment is
sufficient to avoid the stall condition)
- To support frame sizes that are larger than 4K bytes, there are
two options:
1. Large single buffer frames that span a 4KB page boundary can
be converted into SG frames to avoid transaction splits at
the 4KB boundary,
2. Align the large single buffer to 256B address boundaries,
ensure that the frame address plus offset is 256B aligned.
- If software generated SG frames have buffers that are unaligned
and with random non-multiple of 16 byte lengths, before
transmitting such frames via FMAN, frames will need to be copied
into a new single buffer or multiple buffer SG frame that is
compliant with the three rules listed above.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Detect the presence of the A050385 erratum.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The LS1043A SoC is affected by the A050385 erratum stating that
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak thus stopping further packet processing.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak; thus stopping further packet processing.
The FMAN internal queue can overflow when FMAN splits single
read or write transactions into multiple smaller transactions
such that more than 17 AXI transactions are in flight from FMAN
to interconnect. When the FMAN internal queue overflows, it can
stall further packet processing. The issue can occur with any one
of the following three conditions:
1. FMAN AXI transaction crosses 4K address boundary (Errata
A010022)
2. FMAN DMA address for an AXI transaction is not 16 byte
aligned, i.e. the last 4 bits of an address are non-zero
3. Scatter Gather (SG) frames have more than one SG buffer in
the SG list and any one of the buffers, except the last
buffer in the SG list has data size that is not a multiple
of 16 bytes, i.e., other than 16, 32, 48, 64, etc.
With any one of the above three conditions present, there is
likelihood of stalled FMAN packet processing, especially under
stress with multiple ports injecting line-rate traffic.
To avoid situations that stall FMAN packet processing, all of the
above three conditions must be avoided; therefore, configure the
system with the following rules:
1. Frame buffers must not span a 4KB address boundary, unless
the frame start address is 256 byte aligned
2. All FMAN DMA start addresses (for example, BMAN buffer
address, FD[address] + FD[offset]) are 16B aligned
3. SG table and buffer addresses are 16B aligned and the size
of SG buffers are multiple of 16 bytes, except for the last
SG buffer that can be of any size.
Additional workaround notes:
- Address alignment of 64 bytes is recommended for maximally
efficient system bus transactions (although 16 byte alignment is
sufficient to avoid the stall condition)
- To support frame sizes that are larger than 4K bytes, there are
two options:
1. Large single buffer frames that span a 4KB page boundary can
be converted into SG frames to avoid transaction splits at
the 4KB boundary,
2. Align the large single buffer to 256B address boundaries,
ensure that the frame address plus offset is 256B aligned.
- If software generated SG frames have buffers that are unaligned
and with random non-multiple of 16 byte lengths, before
transmitting such frames via FMAN, frames will need to be copied
into a new single buffer or multiple buffer SG frame that is
compliant with the three rules listed above.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Patches to bump position index from sysctl seq_next,
from Vasilin Averin.
2) Release flowtable hook from error path, from Florian Westphal.
3) Patches to add missing netlink attribute validation,
from Jakub Kicinski.
4) Missing NFTA_CHAIN_FLAGS in nf_tables_fill_chain_info().
5) Infinite loop in module autoload if extension is not available,
from Florian Westphal.
6) Missing module ownership in inet/nat chain type definition.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest update from Shuah Khan:
"This consists of a cleanup patch to undo changes to global .gitignore
that added selftests/lkdtm objects and add them to a local
selftests/lkdtm/.gitignore.
Summary of Linus's comments on local vs. global gitignore scope:
- Keep local gitignore patterns in local files.
- Put only global gitignore patterns in the top-level gitignore file.
Local scope keeps things much better separated. It also incidentally
means that if a directory gets renamed, the gitignore file continues
to work unless in the case of renaming the actual files themselves
that are named in the gitignore"
* tag 'linux-kselftest-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftest/lkdtm: Use local .gitignore
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
"This contains a handful of fixes that I would like to target for 5.6:
- A pair of fixes to module loading, which we hope solve the last of
the issues with module text being loaded too sparsely for our call
relocations.
- A Kconfig fix that disallows selecting memory models not supported
by NOMMU.
- A series of Kconfig updates to ease selecting the drivers necessary
to run on QEMU's virt platform.
- DTS updates for SiFive's HiFive Unleashed.
- A fix to our seccomp support that avoids mangling restartable
syscalls"
* tag 'riscv-for-linus-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: fix seccomp reject syscall code path
riscv: dts: Add GPIO reboot method to HiFive Unleashed DTS file
RISC-V: Select Goldfish RTC driver for QEMU virt machine
RISC-V: Select SYSCON Reboot and Poweroff for QEMU virt machine
RISC-V: Enable QEMU virt machine support in defconfigs
RISC-V: Add kconfig option for QEMU virt machine
riscv: Fix range looking for kernel image memblock
riscv: Force flat memory model with no-mmu
riscv: Change code model of module to medany to improve data accessing
riscv: avoid the PIC offset of static percpu data in module beyond 2G limits
|
|
This makes the script more convenient to run.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
"Another batch of DT fixes. I think this should be the last of it, but
sending pull requests seems to cause people to send more fixes.
Summary:
- Fixes for warnings introduced by hierarchical PSCI binding changes
- Fixes for broken doc references due to DT schema conversions
- Several grammar and typo fixes
- Fix a bunch of dtc warnings in examples"
* tag 'devicetree-fixes-for-5.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: arm: Fixup the DT bindings for hierarchical PSCI states
dt-bindings: power: Extend nodename pattern for power-domain providers
MAINTAINERS: update ALLWINNER CPUFREQ DRIVER entry
dt-bindings: bus: Drop empty compatible string in example
dt-bindings: power: Convert domain-idle-states bindings to json-schema
dt-bindings: arm: Fix cpu compatibles in the hierarchical example for PSCI
dt-bindings: arm: Correct links to idle states definitions
dt-bindings: mfd: Fix typo in file name of twl-familly.txt
dt-bindings: mfd: tps65910: Improve grammar
dt-bindings: mfd: zii,rave-sp: Fix a typo ("onborad")
dt-bindings: arm: fsl: fix APF6Dev compatible
dt-bindings: Fix dtc warnings in examples
docs: dt: fix several broken doc references
docs: dt: fix several broken references due to renames
MAINTAINERS: clean up PCIE DRIVER FOR CAVIUM THUNDERX
|
|
Pull vgacon fix from Daniel Vetter:
"One vgacon input check for stable"
* tag 'drm-fixes-2020-03-06-1' of git://anongit.freedesktop.org/drm/drm:
vgacon: Fix a UAF in vgacon_invert_region
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
|
|
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
|
|
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fix from David Sterba:
"One fixup for DIO when in use with the new checksums, a missed case
where the checksum size was still assuming u32"
* tag 'for-5.6-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix RAID direct I/O reads with alternate csums
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux
Pull file locking fixes from Jeff Layton:
"Just a couple of late-breaking patches for the file locking code. The
second patch (from yangerkun) fixes a rather nasty looking potential
use-after-free that should go to stable.
The other patch could technically wait for 5.7, but it's fairly
innocuous so I figured we might as well take it"
* tag 'filelock-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
locks: fix a potential use-after-free problem when wakeup a waiter
fcntl: Distribute switch variables for initialization
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A selection of small fixes, mostly for drivers, that have arrived
since the merge window. None of them are earth shattering in
themselves but all useful for affected systems"
* tag 'spi-fix-v5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi_register_controller(): free bus id on error paths
spi: bcm63xx-hsspi: Really keep pll clk enabled
spi: atmel-quadspi: fix possible MMIO window size overrun
spi/zynqmp: remove entry that causes a cs glitch
spi: pxa2xx: Add CS control clock quirk
spi: spidev: Fix CS polarity if GPIO descriptors are used
spi: qup: call spi_qup_pm_resume_runtime before suspending
spi: spi-omap2-mcspi: Support probe deferral for DMA channels
spi: spi-omap2-mcspi: Handle DMA size restriction on AM65x
|
|
Re-run the shell fragment that generated the original list.
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of small fixes, one for a minor issue in the stm32-vrefbuf
driver and a documentation fix in the Qualcomm code"
* tag 'regulator-fix-v5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: stm32-vrefbuf: fix a possible overshoot when re-enabling
regulator: qcom_spmi: Fix docs for PM8004
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Fix an error return in the adt7462 driver, bad voltage limits reported
by the xdpe12284 driver, and a broken documentation reference in the
adm1177 driver documentation"
* tag 'hwmon-for-v5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (adt7462) Fix an error return in ADT7462_REG_VOLT()
hwmon: (pmbus/xdpe12284) Add callback for vout limits conversion
docs: adm1177: fix a broken reference
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Here are another three arm64 fixes for 5.6, all pretty minor. Main
thing is fixing a silly bug in the fsl_imx8_ddr PMU driver where we
would zero the counters when disabling them.
- Fix misreporting of ASID limit when KPTI is enabled
- Fix busted NULL pointer checks for GICC structure in ACPI PMU code
- Avoid nobbling the "fsl_imx8_ddr" PMU counters when disabling them"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: context: Fix ASID limit in boot messages
drivers/perf: arm_pmu_acpi: Fix incorrect checking of gicc pointer
drivers/perf: fsl_imx8_ddr: Correct the CLEAR bit definition
|
|
When syzkaller tests, there is a UAF:
BUG: KASan: use after free in vgacon_invert_region+0x9d/0x110 at addr
ffff880000100000
Read of size 2 by task syz-executor.1/16489
page:ffffea0000004000 count:0 mapcount:-127 mapping: (null)
index:0x0
page flags: 0xfffff00000000()
page dumped because: kasan: bad access detected
CPU: 1 PID: 16489 Comm: syz-executor.1 Not tainted
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014
Call Trace:
[<ffffffffb119f309>] dump_stack+0x1e/0x20
[<ffffffffb04af957>] kasan_report+0x577/0x950
[<ffffffffb04ae652>] __asan_load2+0x62/0x80
[<ffffffffb090f26d>] vgacon_invert_region+0x9d/0x110
[<ffffffffb0a39d95>] invert_screen+0xe5/0x470
[<ffffffffb0a21dcb>] set_selection+0x44b/0x12f0
[<ffffffffb0a3bfae>] tioclinux+0xee/0x490
[<ffffffffb0a1d114>] vt_ioctl+0xff4/0x2670
[<ffffffffb0a0089a>] tty_ioctl+0x46a/0x1a10
[<ffffffffb052db3d>] do_vfs_ioctl+0x5bd/0xc40
[<ffffffffb052e2f2>] SyS_ioctl+0x132/0x170
[<ffffffffb11c9b1b>] system_call_fastpath+0x22/0x27
Memory state around the buggy address:
ffff8800000fff00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00
ffff8800000fff80: 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00
>ffff880000100000: ff ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff
It can be reproduce in the linux mainline by the program:
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <fcntl.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <sys/ioctl.h>
#include <linux/vt.h>
struct tiocl_selection {
unsigned short xs; /* X start */
unsigned short ys; /* Y start */
unsigned short xe; /* X end */
unsigned short ye; /* Y end */
unsigned short sel_mode; /* selection mode */
};
#define TIOCL_SETSEL 2
struct tiocl {
unsigned char type;
unsigned char pad;
struct tiocl_selection sel;
};
int main()
{
int fd = 0;
const char *dev = "/dev/char/4:1";
struct vt_consize v = {0};
struct tiocl tioc = {0};
fd = open(dev, O_RDWR, 0);
v.v_rows = 3346;
ioctl(fd, VT_RESIZEX, &v);
tioc.type = TIOCL_SETSEL;
ioctl(fd, TIOCLINUX, &tioc);
return 0;
}
When resize the screen, update the 'vc->vc_size_row' to the new_row_size,
but when 'set_origin' in 'vgacon_set_origin', vgacon use 'vga_vram_base'
for 'vc_origin' and 'vc_visible_origin', not 'vc_screenbuf'. It maybe
smaller than 'vc_screenbuf'. When TIOCLINUX, use the new_row_size to calc
the offset, it maybe larger than the vga_vram_size in vgacon driver, then
bad access.
Also, if set an larger screenbuf firstly, then set an more larger
screenbuf, when copy old_origin to new_origin, a bad access may happen.
So, If the screen size larger than vga_vram, resize screen should be
failed. This alse fix CVE-2020-8649 and CVE-2020-8647.
Linus pointed out that overflow checking seems absent. We're saved by
the existing bounds checks in vc_do_resize() with rather strict
limits:
if (cols > VC_RESIZE_MAXCOL || lines > VC_RESIZE_MAXROW)
return -EINVAL;
Fixes: 0aec4867dca14 ("[PATCH] SVGATextMode fix")
Reference: CVE-2020-8647 and CVE-2020-8649
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
[danvet: augment commit message to point out overflow safety]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304022429.37738-1-zhangxiaoxu5@huawei.com
|
|
The hierarchical topology with power-domain should be described through
child nodes, rather than as currently described in the PSCI root node. Fix
this by adding a patternProperties with a corresponding reference to the
power-domain DT binding.
Additionally, update the example to conform to the new pattern, but also to
the adjusted domain-idle-state DT binding.
Fixes: a3f048b5424e ("dt: psci: Update DT bindings to support hierarchical PSCI states")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[robh: Add missing allOf, tweak power-domain node name]
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The existing binding requires the nodename to have a '@', which is a bit
limiting for the wider use case. Therefore, let's extend the pattern to
allow either '@' or '-'.
Fixes: a3f048b5424e ("dt: psci: Update DT bindings to support hierarchical PSCI states")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[robh: drop example change]
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The percpu refcount protects this structure, and we can have an atomic
switch in progress when exiting. This makes it unsafe to just free the
struct normally, and can trigger the following KASAN warning:
BUG: KASAN: use-after-free in percpu_ref_switch_to_atomic_rcu+0xfa/0x1b0
Read of size 1 at addr ffff888181a19a30 by task swapper/0/0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.6.0-rc4+ #5747
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
Call Trace:
<IRQ>
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x3b/0x60
? percpu_ref_switch_to_atomic_rcu+0xfa/0x1b0
? percpu_ref_switch_to_atomic_rcu+0xfa/0x1b0
__kasan_report.cold+0x1a/0x3d
? percpu_ref_switch_to_atomic_rcu+0xfa/0x1b0
percpu_ref_switch_to_atomic_rcu+0xfa/0x1b0
rcu_core+0x370/0x830
? percpu_ref_exit+0x50/0x50
? rcu_note_context_switch+0x7b0/0x7b0
? run_rebalance_domains+0x11d/0x140
__do_softirq+0x10a/0x3e9
irq_exit+0xd5/0xe0
smp_apic_timer_interrupt+0x86/0x200
apic_timer_interrupt+0xf/0x20
</IRQ>
RIP: 0010:default_idle+0x26/0x1f0
Fix this by punting the final exit and free of the struct to RCU, then
we know that it's safe to do so. Jann suggested the approach of using a
double rcu callback to achieve this. It's important that we do a nested
call_rcu() callback, as otherwise the free could be ordered before the
atomic switch, even if the latter was already queued.
Reported-by: syzbot+e017e49c39ab484ac87a@syzkaller.appspotmail.com
Suggested-by: Jann Horn <jannh@google.com>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Set owner to THIS_MODULE, otherwise the nft_chain_nat module might be
removed while there are still inet/nat chains in place.
[ 117.942096] BUG: unable to handle page fault for address: ffffffffa0d5e040
[ 117.942101] #PF: supervisor read access in kernel mode
[ 117.942103] #PF: error_code(0x0000) - not-present page
[ 117.942106] PGD 200c067 P4D 200c067 PUD 200d063 PMD 3dc909067 PTE 0
[ 117.942113] Oops: 0000 [#1] PREEMPT SMP PTI
[ 117.942118] CPU: 3 PID: 27 Comm: kworker/3:0 Not tainted 5.6.0-rc3+ #348
[ 117.942133] Workqueue: events nf_tables_trans_destroy_work [nf_tables]
[ 117.942145] RIP: 0010:nf_tables_chain_destroy.isra.0+0x94/0x15a [nf_tables]
[ 117.942149] Code: f6 45 54 01 0f 84 d1 00 00 00 80 3b 05 74 44 48 8b 75 e8 48 c7 c7 72 be de a0 e8 56 e6 2d e0 48 8b 45 e8 48 c7 c7 7f be de a0 <48> 8b 30 e8 43 e6 2d e0 48 8b 45 e8 48 8b 40 10 48 85 c0 74 5b 8b
[ 117.942152] RSP: 0018:ffffc9000015be10 EFLAGS: 00010292
[ 117.942155] RAX: ffffffffa0d5e040 RBX: ffff88840be87fc2 RCX: 0000000000000007
[ 117.942158] RDX: 0000000000000007 RSI: 0000000000000086 RDI: ffffffffa0debe7f
[ 117.942160] RBP: ffff888403b54b50 R08: 0000000000001482 R09: 0000000000000004
[ 117.942162] R10: 0000000000000000 R11: 0000000000000001 R12: ffff8883eda7e540
[ 117.942164] R13: dead000000000122 R14: dead000000000100 R15: ffff888403b3db80
[ 117.942167] FS: 0000000000000000(0000) GS:ffff88840e4c0000(0000) knlGS:0000000000000000
[ 117.942169] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 117.942172] CR2: ffffffffa0d5e040 CR3: 00000003e4c52002 CR4: 00000000001606e0
[ 117.942174] Call Trace:
[ 117.942188] nf_tables_trans_destroy_work.cold+0xd/0x12 [nf_tables]
[ 117.942196] process_one_work+0x1d6/0x3b0
[ 117.942200] worker_thread+0x45/0x3c0
[ 117.942203] ? process_one_work+0x3b0/0x3b0
[ 117.942210] kthread+0x112/0x130
[ 117.942214] ? kthread_create_worker_on_cpu+0x40/0x40
[ 117.942221] ret_from_fork+0x35/0x40
nf_tables_chain_destroy() crashes on module_put() because the module is
gone.
Fixes: d164385ec572 ("netfilter: nat: add inet family nat support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
'16306a61d3b7 ("fs/locks: always delete_block after waiting.")' add the
logic to check waiter->fl_blocker without blocked_lock_lock. And it will
trigger a UAF when we try to wakeup some waiter：
Thread 1 has create a write flock a on file, and now thread 2 try to
unlock and delete flock a, thread 3 try to add flock b on the same file.
Thread2 Thread3
flock syscall(create flock b)
...flock_lock_inode_wait
flock_lock_inode(will insert
our fl_blocked_member list
to flock a's fl_blocked_requests)
sleep
flock syscall(unlock)
...flock_lock_inode_wait
locks_delete_lock_ctx
...__locks_wake_up_blocks
__locks_delete_blocks(
b->fl_blocker = NULL)
...
break by a signal
locks_delete_block
b->fl_blocker == NULL &&
list_empty(&b->fl_blocked_requests)
success, return directly
locks_free_lock b
wake_up(&b->fl_waiter)
trigger UAF
Fix it by remove this logic, and this patch may also fix CVE-2019-19769.
Cc: stable@vger.kernel.org
Fixes: 16306a61d3b7 ("fs/locks: always delete_block after waiting.")
Signed-off-by: yangerkun <yangerkun@huawei.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
|
|
The bfq_find_set_group() function takes as input a blkcg (which represents
a cgroup) and retrieves the corresponding bfq_group, then it updates the
bfq internal group hierarchy (see comments inside the function for why
this is needed) and finally it returns the bfq_group.
In the hierarchy update cycle, the pointer holding the correct bfq_group
that has to be returned is mistakenly used to traverse the hierarchy
bottom to top, meaning that in each iteration it gets overwritten with the
parent of the current group. Since the update cycle stops at root's
children (depth = 2), the overwrite becomes a problem only if the blkcg
describes a cgroup at a hierarchy level deeper than that (depth > 2). In
this case the root's child that happens to be also an ancestor of the
correct bfq_group is returned. The main consequence is that processes
contained in a cgroup at depth greater than 2 are wrongly placed in the
group described above by BFQ.
This commits fixes this problem by using a different bfq_group pointer in
the update cycle in order to avoid the overwrite of the variable holding
the original group reference.
Reported-by: Kwon Je Oh <kwonje.oh2@gmail.com>
Signed-off-by: Carlo Nonato <carlo.nonato95@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
