| Age | Commit message (Collapse) | Author |
|---|
|
Before commit 7627a0edef54 ("ata: ahci: Drop low power policy board type")
the ATI AHCI controllers specified board type 'board_ahci' rather than
board type 'board_ahci'. This means that LPM was historically not enabled
for the ATI AHCI controllers.
By looking at commit 7a8526a5cd51 ("libata: Add ATA_HORKAGE_NO_NCQ_ON_ATI
for Samsung 860 and 870 SSD."), it is clear that, for some unknown reason,
that Samsung SSDs do not play nice with ATI AHCI controllers. (When using
other AHCI controllers, NCQ can be enabled on these Samsung SSDs without
issues.)
In a similar way, from user reports, it is clear the ATI AHCI controllers
can enable LPM on e.g. Maxtor HDDs perfectly fine, but when enabling LPM
on certain Samsung SSDs, things break. (E.g. the SSDs will not get detected
by the ATI AHCI controller even after a COMRESET.)
Yet, when using LPM on these Samsung SSDs with other AHCI controllers, e.g.
Intel AHCI controllers, these Samsung drives appear to work perfectly fine.
Considering that the combination of ATI + Samsung, for some unknown reason,
does not seem to work well, disable LPM when detecting an ATI AHCI
controller with a problematic Samsung SSD.
Apply this new ATA_QUIRK_NO_LPM_ON_ATI quirk for all Samsung SSDs that have
already been reported to not play nice with ATI (ATA_QUIRK_NO_NCQ_ON_ATI).
Fixes: 7627a0edef54 ("ata: ahci: Drop low power policy board type")
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Reported-by: Eric <eric.4.debian@grabatoulnz.fr>
Closes: https://lore.kernel.org/linux-ide/Z8SBZMBjvVXA7OAK@eldamar.lan/
Tested-by: Eric <eric.4.debian@grabatoulnz.fr>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20250317170348.1748671-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
Currently iwlmld_kunit_add_chanctx receives a band, picks a predefined
static chandef, and creates the chanctx from it.
Change it to receive a bandwidth as well. Otherwise, the bandwidth in
the chanctx/phy will be different than what test specified in the
iwl_mld_kunit_link.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250313002008.85a1285d34cd.Ia71cdcd4241fe73501bc93e3cb2c6bb3f631b9ec@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
To allow setting up association/EMLSR states with more flexibility,
change the relevant functions to receive a new struct, iwl_mld_kunit_link,
which will contain all the link parameters (for now just link id, band
and bandwidth).
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250313002008.f336491ccc4e.I6b727765eb394a3dbb78cea71e356be1bdc4a17c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Allow EMLSR if the bandwidths of the links are unequal if one of the
following conditions is true:
1. in low latency mode
2. bandwidth of the secondary link is greater than the bandwidth of the
primary
3. the primary link is active and is loaded enough to justify EMLSR
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250313002008.150c330711c4.Ifd72d2e076783991852a7f1756948b4f0efb9fea@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We exit EMLSR mode if the FW requested to do so.
To prevent repeated toggling of the EMLSR mode (frequent entry and
exit), add this exit reason to the EMLSR prevention mechanism.
This mechanism avoids re-entering EMLSR for a certain period of time
after multiple exits caused by the same reason.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250313002008.f0e74a7f99af.I447c8788afba85a2a5040ae2c1213b6e05ec14f3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The channel load logic moves from the FW to the driver.
- Implement the logic: allow EMLSR only if the candidate primary link is
active and if its average channel load exceeds the threshold.
- Remove IWL_MLD_EMLSR_BLOCKED_FW. Instead, treat ESR_RECOMMEND_LEAVE in
the EMLSR_RECOMMENDATION notif as an EXIT reason.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250313002008.6729a8d67815.Iab39bf0982d8cdbb0db701d31854101c2fcf3b64@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add debugfs file in mld to retrieve TAS status per radio, TAS block list,
current mcc, OEM name and OEM allowed list. This will add ability to get
TAS status to user application via debugfs and required for debugging.
Add the required API definitions and some debug host command utils.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250313002008.66524c6ea198.I1625135284fc075148a55dd9ac629e94ca881fe4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The WIPHY_DEBUGFS_READ_WRITE_FILE_OPS_MLD macro is intended to call
read/write handlers with the wiphy lock held. However, the current
implementation uses the MLD_DEBUGFS_READ_WRAPPER macro, which does
not hold the wiphy lock during read operations. This fix updates
the WIPHY_DEBUGFS_READ_WRITE_FILE_OPS_MLD macro to use the
WIPHY_DEBUGFS_READ_WRAPPER_MLD macro instead, ensuring that the
wiphy lock is held during both read and write operations.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250313002008.2001d2335e9d.I607a8bd12efc6d1190cef1fca44279dbdd2756ea@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Introduced the WIPHY_DEBUGFS_READ_FILE_OPS_MLD macro to enable reading
data from the driver while holding the wiphy lock.
This will enable read operations with wiphy locked.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250313002008.b0ddb6b0a144.I1fab63f2c6f52fea61cc5d7b27775aed58adfd8d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
WIPHY_DEBUGFS_WRITE_HANDLER_WRAPPER
Renamed the macro WIPHY_DEBUGFS_HANDLER_WRAPPER to
WIPHY_DEBUGFS_WRITE_HANDLER_WRAPPER to better reflect its purpose as a
write handler.
Additionally, updated the corresponding macro
WIPHY_DEBUGFS_HANDLER_WRAPPER_MLD to
WIPHY_DEBUGFS_WRITE_HANDLER_WRAPPER_MLD for consistency.
This change does not alter the functionality but enhances the
maintainability of the code.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250313002008.bb8a1d7907c8.I53325f2f37ccaad2b212d35d10616e06c1555e48@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Link ID to store chandef is still being used as 0 even in case of MLO which
is incorrect. This leads to issue during CAC completion where link 0 as well
gets stopped.
Fixes: 0b7798232eee ("wifi: cfg80211/mac80211: use proper link ID for DFS")
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250314-fix_starting_cac_during_mlo-v1-1-3b51617d7ea5@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add selection for GUEST_PERF_EVENTS if KVM is enabled, also add perf
callback register when KVM module is loading.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Three architecture specific functions are added for the guest perf
feature, they are kvm_arch_vcpu_in_kernel(), kvm_arch_vcpu_get_ip()
and kvm_arch_pmi_in_guest().
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Pause-Loop Exiting is not supported by LoongArch hardware, nor is pv
spinlock feature. So function kvm_vcpu_on_spin() is not used. Function
kvm_arch_vcpu_preempted_in_kernel() is defined as a stub function here
since it is only called by unused function kvm_vcpu_on_spin().
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
PGD table for primary mmu keeps unchanged once VM is created, it is not
necessary to save PGD table pointer during VM context switch. And it can
be acquired when VM is created.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
arch/loongarch/kvm/ includes local headers with the double-quote form
(#include "..."). Also, TRACE_INCLUDE_PATH in arch/loongarch/kvm/trace.h
is relative to include/trace/.
Hence, the local header search path is unneeded.
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
There are a few conflicts between the work that went
into wireless and that's here now, resolve them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When build the kernel using the llvm-18.1.3-rust-1.85.0-x86_64
with ARCH=arm64, the following symbols are generated:
$nm vmlinux | grep ' _R'.*SeqFile | rustfilt
ffff8000805b78ac T <kernel::seq_file::SeqFile>::call_printf
This Rust symbol is trivial wrappers around the C functions seq_printf.
It doesn't make sense to go through a trivial wrapper for its functions,
so mark it inline.
Link: https://github.com/Rust-for-Linux/linux/issues/1145
Suggested-by: Alice Ryhl <aliceryhl@google.com>
Co-developed-by: Grace Deng <Grace.Deng006@Gmail.com>
Signed-off-by: Grace Deng <Grace.Deng006@Gmail.com>
Signed-off-by: Kunwu Chan <kunwu.chan@hotmail.com>
Link: https://lore.kernel.org/r/20250317030418.2371265-1-kunwu.chan@linux.dev
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Reviewed-by: Benno Lossin <benno.lossin@proton.me>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
When build the kernel using the llvm-18.1.3-rust-1.85.0-x86_64
with ARCH=arm64, the following symbols are generated:
$ nm vmlinux | grep ' _R'.*FileDescriptorReservation | rustfilt
... T <kernel::fs::file::FileDescriptorReservation>::fd_install
... T <kernel::fs::file::FileDescriptorReservation>::get_unused_fd_flags
... T <kernel::fs::file::FileDescriptorReservation as core::ops::drop::Drop>::drop
These Rust symbols are trivial wrappers around the C functions
fd_install, put_unused_fd and put_task_struct. It
doesn't make sense to go through a trivial wrapper for these
functions, so mark them inline.
Link: https://github.com/Rust-for-Linux/linux/issues/1145
Suggested-by: Alice Ryhl <aliceryhl@google.com>
Co-developed-by: Grace Deng <Grace.Deng006@Gmail.com>
Signed-off-by: Grace Deng <Grace.Deng006@Gmail.com>
Signed-off-by: Kunwu Chan <kunwu.chan@hotmail.com>
Link: https://lore.kernel.org/r/20250317023702.2360726-1-kunwu.chan@linux.dev
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Maxime Chevallier says:
====================
net: phy: Rework linkmodes handling in a dedicated file
This is V5 of the phy_caps series. In a nutshell, this series reworks the way
we maintain the list of speed/duplex capablities for each linkmode so that we
no longer have multiple definition of these associations.
That will help making sure that when people add new linkmodes in
include/uapi/linux/ethtool.h, they don't have to update phylib and phylink as
well, making the process more straightforward and less error-prone.
It also generalises the phy_caps interface to be able to lookup linkmodes
from phy_interface_t, which is needed for the multi-port work I've been working
on for a while.
This V5 addresse Russell's and Paolo's reviews, namely :
- Error out when encountering an unknown SPEED_XXX setting
It prints an error and fails to initialize phylib. I've tested by
introducing a dummy 1.6T speed, I guess it's only a matter of time
before that actually happens :)
- Deal more gracefully with the fixed-link settings, keeping some level of
compatibility with what we had before by making sure we report a
single BaseT mode like before.
V1 : https://lore.kernel.org/netdev/20250222142727.894124-1-maxime.chevallier@bootlin.com/
V2 : https://lore.kernel.org/netdev/20250226100929.1646454-1-maxime.chevallier@bootlin.com/
V3 : https://lore.kernel.org/netdev/20250228145540.2209551-1-maxime.chevallier@bootlin.com/
V4 : https://lore.kernel.org/netdev/20250303090321.805785-1-maxime.chevallier@bootlin.com/
====================
Link: https://patch.msgid.link/20250307173611.129125-1-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Currently, both ata_dev_config_ncq_send_recv() - which checks for NCQ
Send/Recv Log (Log Address 13h) and ata_dev_config_ncq_non_data() -
which checks for NCQ Non-Data Log (Log Address 12h), uses the same
print when the log is not supported:
"NCQ Send/Recv Log not supported"
This seems like a copy paste error, since NCQ Non-Data Log is actually
a separate log.
Fix the print to reference the correct log.
Fixes: 284b3b77ea88 ("libata: NCQ encapsulation for ZAC MANAGEMENT OUT")
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20250317111754.1666084-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
Phylink has internal code to get the MAC capabilities of a given PHY
interface (what are the supported speed and duplex).
Extract that into phy_caps, but use the link_capa for conversion. Add an
internal phylink helper for the link caps -> mac caps conversion, and
use this in phylink_caps_to_linkmodes().
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-14-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
phylink_caps_to_linkmodes() is used to derive a list of linkmodes that
can be conceivably exposed using a given set of speeds and duplex
through phylink's MAC capabilities.
This list can be derived from the link_caps array in phy_caps, provided
we convert the MAC capabilities into a LINK_CAPA bitmask first.
Introduce an internal phylink helper phylink_caps_to_link_caps() to
convert from MAC capabilities into phy_caps, then phy_caps_linkmodes()
to do the link_caps -> linkmodes conversion.
This avoids having to update phylink for every new linkmode.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-13-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
phylink allows MAC drivers to report the capabilities in terms of speed,
duplex and pause support. This is done through a dedicated set of enum
values in the form of the MAC_ capabilities. They are very close to what
the LINK_CAPA_xxx can express, with the difference that LINK_CAPA don't
have any information about Pause/Asym Pause support.
To prepare converting phylink to using the phy_caps, add the mapping
between MAC capabilities and phy_caps. While doing so, we move the
phylink_caps_params array up a bit to simplify future commits.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-12-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The phy_settings array is no longer relevant as it has now been replaced
by the link_caps array and associated phy_caps helpers.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-11-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When phylink creates a fixed-link configuration, it finds a matching
linkmode to set as the advertised, lp_advertising and supported modes
based on the speed and duplex of the fixed link.
Use the newly introduced phy_caps_lookup to get these modes instead of
phy_lookup_settings(). This has the side effect that the matched
settings and configured linkmodes may now contain several linkmodes (the
intersection of supported linkmodes from the phylink settings and the
linkmodes that match speed/duplex) instead of the one from
phy_lookup_settings().
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-10-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When configuring PHY advertising with autoneg disabled, we lookd for an
exact linkmode to advertise and configure for the requested Speed and
Duplex, specially at or over 1G.
Using phy_caps_lookup allows us to build a list of the supported
linkmodes at that speed that we can advertise instead of the first mode
that matches.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-9-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As the link_caps array is efficient for <speed,duplex> lookups,
implement a function for speed/duplex lookups that matches a given
mask. This replicates to some extent the phy_lookup_settings()
behaviour, matching full link_capabilities instead of a single linkmode.
phy.c's phy_santize_settings() and phylink's
phylink_ethtool_ksettings_set() performs such lookup using the
phy_settings table, but are only interested in the actual speed/duplex
that were matched, rathet than the individual linkmode.
Similar to phy_lookup_settings(), the newly introduced phy_caps_lookup()
will run through the link_caps[] array by descending speed/duplex order.
If the link_capabilities for a given <speed/duplex> tuple intersects the
passed linkmodes, we consider that a match.
Similar to phy_lookup_settings(), we also allow passing an 'exact'
boolean, allowing non-exact match. Here, we MUST always match the
linkmodes mask, but we allow matching on lower speed settings.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-8-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In several occasions, phylib needs to lookup a set of matching speed and
duplex against a given linkmode set. Instead of relying on the
phy_settings array and thus iterate over the whole linkmodes list, use
the link_capabilities array to lookup these matches, as we aren't
interested in the actual link setting that matches but rather the speed
and duplex for that setting.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-7-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
With the link_capabilities array, it's trivial to validate a given mask
againts a <speed, duplex> tuple. Create a helper for that purpose, and
use it to replace a phy_settings lookup in phy_check_valid();
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-6-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Convert the __set_linkmode_max_speed to use the link_capabilities array.
This makes it easy to clamp the linkmodes to a given max speed.
Introduce a new helper phy_caps_linkmode_max_speed to replace the
previous one that used phy_settings.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-5-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Use the newly introduced link_capabilities array to derive the list of
possible speeds when given a combination of linkmodes. As
link_capabilities is indexed by speed, we don't have to iterate the
whole phy_settings array.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-4-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The canonical definition for all the link modes is in linux/ethtool.h,
which is complemented by the link_mode_params array stored in
net/ethtool/common.h . That array contains all the metadata about each
of these modes, including the Speed and Duplex information.
Phylib and phylink needs that information as well for internal
management of the link, which was done by duplicating that information
in locally-stored arrays and lookup functions. This makes it easy for
developpers adding new modes to forget modifying phylib and phylink
accordingly.
However, the link_mode_params array in net/ethtool/common.c is fairly
inefficient to search through, as it isn't sorted in any manner. Phylib
and phylink perform a lot of lookup operations, mostly to filter modes
by speed and/or duplex.
We therefore introduce the link_caps private array in phy_caps.c, that
indexes linkmodes in a more efficient manner. Each element associated a
tuple <speed, duplex> to a bitfield of all the linkmodes runs at these
speed/duplex.
We end-up with an array that's fairly short, easily addressable and that
it optimised for the typical use-cases of phylib/phylink.
That array is initialized at the same time as phylib. As the
link_mode_params array is part of the net stack, which phylink depends
on, it should always be accessible from phylib.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-3-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
link_mode_params contains a lookup table of all 802.3 link modes that
are currently supported with structured data about each mode's speed,
duplex, number of lanes and mediums.
As a preparation for a port representation, export that table for the
rest of the net stack to use.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-2-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
LSMs often inspect the path.mnt of files in the security hooks, and this
causes a NULL deref in efivarfs_pm_notify() because the path is
constructed with a NULL path.mnt.
Fix by obtaining from vfs_kern_mount() instead, and being very careful
to ensure that deactivate_super() (potentially triggered by a racing
userspace umount) is not called directly from the notifier, because it
would deadlock when efivarfs_kill_sb() tried to unregister the notifier
chain.
[ Al notes:
Umm... That's probably safe, but not as a long-term solution -
it's too intimately dependent upon fs/super.c internals. The
reasons why you can't run into ->s_umount deadlock here are
non-trivial... ]
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Link: https://lore.kernel.org/r/e54e6a2f-1178-4980-b771-4d9bafc2aa47@tnxip.de
Link: https://lore.kernel.org/r/3e998bf87638a442cbc6864cdcd3d8d9e08ce3e3.camel@HansenPartnership.com
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
If kvm_arch_vcpu_create() fails to share the vCPU page with the
hypervisor, we propagate the error back to the ioctl but leave the
vGIC vCPU data initialised. Note only does this leak the corresponding
memory when the vCPU is destroyed but it can also lead to use-after-free
if the redistributor device handling tries to walk into the vCPU.
Add the missing cleanup to kvm_arch_vcpu_create(), ensuring that the
vGIC vCPU structures are destroyed on error.
Cc: <stable@vger.kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Oliver Upton <oliver.upton@linux.dev>
Cc: Quentin Perret <qperret@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20250314133409.9123-1-will@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
There's nothing used in the SPI NOR core from <linux/of_platform.h>,
drop the header inclusion.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20250307-spi-nor-headers-cleanup-v1-3-c186a9511c1e@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
|
|
The core driver is using of_property_read_bool() and relies on implicit
inclusion of <linux/of.h>, which comes from <linux/mtd/mtd.h>.
It is good practice to directly include all headers used, it avoids
implicit dependencies and spurious breakage if someone rearranges
headers and causes the implicit include to vanish.
Include the missing header.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20250307-spi-nor-headers-cleanup-v1-1-c186a9511c1e@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc hotfixes from Andrew Morton:
"15 hotfixes. 7 are cc:stable and the remainder address post-6.13
issues or aren't considered necessary for -stable kernels.
13 are for MM and the other two are for squashfs and procfs.
All are singletons. Please see the individual changelogs for details"
* tag 'mm-hotfixes-stable-2025-03-17-20-09' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/page_alloc: fix memory accept before watermarks gets initialized
mm: decline to manipulate the refcount on a slab page
memcg: drain obj stock on cpu hotplug teardown
mm/huge_memory: drop beyond-EOF folios with the right number of refs
selftests/mm: run_vmtests.sh: fix half_ufd_size_MB calculation
mm: fix error handling in __filemap_get_folio() with FGP_NOWAIT
mm: memcontrol: fix swap counter leak from offline cgroup
mm/vma: do not register private-anon mappings with khugepaged during mmap
squashfs: fix invalid pointer dereference in squashfs_cache_delete
mm/migrate: fix shmem xarray update during migration
mm/hugetlb: fix surplus pages in dissolve_free_huge_page()
mm/damon/core: initialize damos->walk_completed in damon_new_scheme()
mm/damon: respect core layer filters' allowance decision on ops layer
filemap: move prefaulting out of hot write path
proc: fix UAF in proc_get_inode()
|
|
Unfortunately I no longer have time to meaningfully take part in the
linux kernel development.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
commit 79add3a3f795e ("ext4: notify when discard is not supported")
noted that keeping the DISCARD flag is for possibility that the underlying
device might change in future even without file system remount. However,
this scenario has rarely occurred in practice on the device side. Even if
it does occur, it can be resolved with remount. Clearing the DISCARD flag
not only prevents confusion caused by mount options but also avoids
sending unnecessary discard commands.
Signed-off-by: Diangang Li <lidiangang@bytedance.com>
Link: https://patch.msgid.link/20250311021310.669524-1-lidiangang@bytedance.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Since the function jbd2_journal_unfile_buffer() is no longer called
anywhere after commit e5a120aeb57f ("jbd2: remove journal_head from
descriptor buffers"), so let's remove it.
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20250306063240.157884-1-libaokun@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
capable() calls refer to enabled LSMs whether to permit or deny the
request. This is relevant in connection with SELinux, where a
capability check results in a policy decision and by default a denial
message on insufficient permission is issued.
It can lead to three undesired cases:
1. A denial message is generated, even in case the operation was an
unprivileged one and thus the syscall succeeded, creating noise.
2. To avoid the noise from 1. the policy writer adds a rule to ignore
those denial messages, hiding future syscalls, where the task
performs an actual privileged operation, leading to hidden limited
functionality of that task.
3. To avoid the noise from 1. the policy writer adds a rule to permit
the task the requested capability, while it does not need it,
violating the principle of least privilege.
Signed-off-by: Christian Göttsche <cgzones@googlemail.com>
Reviewed-by: Serge Hallyn <serge@hallyn.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20250302160657.127253-2-cgoettsche@seltendoof.de
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Commit 196e402adf2e ("ext4: improve cr 0 / cr 1 group scanning") introduces
the sysfs control interface "mb_max_linear_groups" to address the problem
that rotational devices performance degrades when the "mb_optimize_scan"
feature is enabled, which may result in distant block group allocation.
However, the name of the interface was incorrect in the comment to the
ext4/mballoc.c file, and this patch fixes it, without further changes.
Signed-off-by: Zizhi Wo <wozizhi@huawei.com>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Link: https://patch.msgid.link/20250224012005.689549-1-wozizhi@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
In __jbd2_journal_erase(), the block_stop parameter includes the last
block of a contiguous region; however, the calculation of byte_stop is
incorrect, as it does not account for the bytes in that last block.
Consequently, the page cache is not cleared properly, which occasionally
causes the ext4/050 test to fail.
Since block_stop operates on inclusion semantics, it involves repeated
increments and decrements by 1, significantly increasing the complexity
of the calculations. Optimize the calculation and fix the incorrect
byte_stop by make both block_stop and byte_stop to use exclusion
semantics.
This fixes a failure in fstests ext4/050.
Fixes: 01d5d96542fd ("ext4: add discard/zeroout flags to journal flush")
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20250217065955.3829229-1-yi.zhang@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Buffer heads are attached to folios, not to pages. Also
flush_dcache_page() is now deprecated in favour of flush_dcache_folio().
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20250213182303.2133205-1-willy@infradead.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Otherwise, if ext4_inode_attach_jinode() fails, a hung task will
happen because filemap_invalidate_unlock() isn't called to unlock
mapping->invalidate_lock. Like this:
EXT4-fs error (device sda) in ext4_setattr:5557: Out of memory
INFO: task fsstress:374 blocked for more than 122 seconds.
Not tainted 6.14.0-rc1-next-20250206-xfstests-dirty #726
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:fsstress state:D stack:0 pid:374 tgid:374 ppid:373
task_flags:0x440140 flags:0x00000000
Call Trace:
<TASK>
__schedule+0x2c9/0x7f0
schedule+0x27/0xa0
schedule_preempt_disabled+0x15/0x30
rwsem_down_read_slowpath+0x278/0x4c0
down_read+0x59/0xb0
page_cache_ra_unbounded+0x65/0x1b0
filemap_get_pages+0x124/0x3e0
filemap_read+0x114/0x3d0
vfs_read+0x297/0x360
ksys_read+0x6c/0xe0
do_syscall_64+0x4b/0x110
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Fixes: c7fc0366c656 ("ext4: partial zero eof block on unaligned inode size extension")
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Link: https://patch.msgid.link/20250213112247.3168709-1-libaokun@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
There's issue as follows:
BUG: KASAN: use-after-free in ext4_xattr_inode_dec_ref_all+0x6ff/0x790
Read of size 4 at addr ffff88807b003000 by task syz-executor.0/15172
CPU: 3 PID: 15172 Comm: syz-executor.0
Call Trace:
__dump_stack lib/dump_stack.c:82 [inline]
dump_stack+0xbe/0xfd lib/dump_stack.c:123
print_address_description.constprop.0+0x1e/0x280 mm/kasan/report.c:400
__kasan_report.cold+0x6c/0x84 mm/kasan/report.c:560
kasan_report+0x3a/0x50 mm/kasan/report.c:585
ext4_xattr_inode_dec_ref_all+0x6ff/0x790 fs/ext4/xattr.c:1137
ext4_xattr_delete_inode+0x4c7/0xda0 fs/ext4/xattr.c:2896
ext4_evict_inode+0xb3b/0x1670 fs/ext4/inode.c:323
evict+0x39f/0x880 fs/inode.c:622
iput_final fs/inode.c:1746 [inline]
iput fs/inode.c:1772 [inline]
iput+0x525/0x6c0 fs/inode.c:1758
ext4_orphan_cleanup fs/ext4/super.c:3298 [inline]
ext4_fill_super+0x8c57/0xba40 fs/ext4/super.c:5300
mount_bdev+0x355/0x410 fs/super.c:1446
legacy_get_tree+0xfe/0x220 fs/fs_context.c:611
vfs_get_tree+0x8d/0x2f0 fs/super.c:1576
do_new_mount fs/namespace.c:2983 [inline]
path_mount+0x119a/0x1ad0 fs/namespace.c:3316
do_mount+0xfc/0x110 fs/namespace.c:3329
__do_sys_mount fs/namespace.c:3540 [inline]
__se_sys_mount+0x219/0x2e0 fs/namespace.c:3514
do_syscall_64+0x33/0x40 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x67/0xd1
Memory state around the buggy address:
ffff88807b002f00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff88807b002f80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff88807b003000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
^
ffff88807b003080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff88807b003100: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Above issue happens as ext4_xattr_delete_inode() isn't check xattr
is valid if xattr is in inode.
To solve above issue call xattr_check_inode() check if xattr if valid
in inode. In fact, we can directly verify in ext4_iget_extra_inode(),
so that there is no divergent verification.
Fixes: e50e5129f384 ("ext4: xattr-in-inode support")
Signed-off-by: Ye Bin <yebin10@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20250208063141.1539283-3-yebin@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Introduce ITAIL helper to get the bound of xattr in inode.
Signed-off-by: Ye Bin <yebin10@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20250208063141.1539283-2-yebin@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
In the days when SCSI-2 was emerging, some drives did claim SCSI-2 but did
not correctly implement it. The st driver first tries MODE SELECT with the
page format bit set to set the block descriptor. If not successful, the
non-page format is tried.
The test only tests the sense code and this triggers also from illegal
parameter in the parameter list. The test is limited to "old" devices and
made more strict to remove false alarms.
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Link: https://lore.kernel.org/r/20250311112516.5548-4-Kai.Makisara@kolumbus.fi
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
