| Age | Commit message (Collapse) | Author |
|---|
|
Specify IRQF_SHARED to support shared interrupts. If the interrupt
handler is called and the device is not indicating an interrupt,
just return IRQ_NONE rather than spewing error messages.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These registers are important for troubleshooting the state of the DMA
cores.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for setting the RX and TX ring sizes for this driver using
ethtool. Also increase the default RX ring size as the previous default
was far too low for good performance in some configurations.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Xilinx DMA blocks each have their own reset register, but they both
reset the entire DMA engine, so only one of them needs to be reset.
Also, when stopping the device, we need to not just command the DMA
blocks to stop, but wait for them to stop, and trigger a device reset
to ensure that they are completely stopped.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MDIO clock divisor register setting was only applied on the initial
startup when the driver was loaded. However, this setting is cleared
when the device is reset, such as would occur when the interface was
taken down and brought up again, and so the MDIO bus would be
non-functional afterwards.
Split up the MDIO bus setup and enable into separate functions and
re-enable the bus after a device reset, to ensure that the MDIO
registers are set properly. This also allows us to remove direct access
to MDIO registers in xilinx_axienet_main.c and centralize them all in
xilinx_axienet_mdio.c.
Also, lock the MDIO bus lock around the device reset process, to avoid
MDIO accesses from occurring while the MDIO is disabled during the reset.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the MDIO is is brought up before the netdev is registered, it
should be torn down after the netdev is removed. Otherwise, PHY accesses
can potentially access freed MDIO bus references and cause a crash.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver was previously always calculating the MDIO clock divisor
(from AXI bus clock to MDIO bus clock) based on the CPU clock frequency,
assuming that it is the same as the AXI bus frequency, but that
simplistic method only works on the MicroBlaze platform.
Add support for specifying the clock used for the device in the device
tree using the clock framework. If the clock is specified then it will
be used when calculating the clock divisor. The previous CPU clock
detection method is left for backward compatibility if no clock is
specified.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver should now build on (at least) X86 and ARM platforms, so add
them as supported platforms for the driver in Kconfig.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MDIO bus for this driver was being named using the result of
of_address_to_resource on a node which may not have any resource on it,
but the return value of that call was not checked so it was using some
random value in the bus name. Change to name the MDIO bus based on the
resource start of the actual Ethernet register block.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver was using in_be32 and out_be32 IO accessors which do not
exist on most platforms. Also, the use of big-endian accessors does not
seem correct as this hardware is accessed over an AXI bus which, to the
extent it has an endian-ness, is little-endian. Switch to standard
ioread32/iowrite32 accessors.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver was casting skb pointers to u32 and storing them as such in
the DMA buffer descriptor, which is obviously broken on 64-bit. The area
of the buffer descriptor being used is not accessed by the hardware and
has sufficient room for a 32 or 64-bit pointer, so just store the skb
pointer as such.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Assorted set of patches for Arm DRM drivers that I maintain
in my tree.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Liviu Dudau <Liviu.Dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190604144205.GO15316@e110455-lin.cambridge.arm.com
|
|
On the Arria10, Agilex, and Stratix10 SoC, there are a few differences from
the Cyclone5 and Arria5:
- The emac PHY setup bits are in separate registers.
- The PTP reference clock select mask is different.
- The register to enable the emac signal from FPGA is different.
Thus, this patch creates a separate function for setting the phy modes on
Arria10/Agilex/Stratix10. The separation is based a new DTS binding:
"altr,socfpga-stmmac-a10-s10".
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the "altr,socfpga-stmmac-a10-s10" binding for Arria10/Agilex/Stratix10
implementation of the stmmac ethernet controller.
On the Arria10, Agilex, and Stratix10 SoCs, there are a few differences from
the Cyclone5 and Arria5:
- The emac PHY setup bits are in separate registers.
- The PTP reference clock select mask is different.
- The register to enable the emac signal from FPGA is different.
Because of these differences, the dwmac-socfpga glue logic driver will
use this new binding to set the appropriate bits for PHY, PTP reference
clock, and signal from FPGA.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jakub Kicinski says:
====================
nfp: tls: add basic TX offload
This series adds initial TLS offload support to the nfp driver.
Only TX side is added for now. We need minor adjustments to
the core tls code:
- expose the per-skb fallback helper;
- grow the driver context slightly;
- add a helper to get to the driver state more easily.
We only support TX offload for now, and only if all packets
keep coming in order. For retransmissions we use the
aforementioned software fallback, and in case there are
local drops we completely give up on given TCP stream.
This will obviously be improved soon, this patch set is the
minimal, functional yet easily reviewable chunk.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Count TX TLS packets: successes, out of order, and dropped due to
missing record info. Make sure the RX and TX completion statistics
don't share cache lines with TX ones as much as possible. With TLS
stats they are no longer reasonably aligned.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the functionality to add and delete TLS connections on
the NFP, received from the kernel TLS callbacks.
Make use of the common control message (CCM) infrastructure to propagate
the kernel state to firmware.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prepend connection handle to each transmitted TLS packet.
For each connection, the driver tracks the next sequence number
expected. If an out of order packet is observed, the driver calls into
the TLS kernel code to reencrypt that particular skb.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While offloading TLS connections, drivers need to handle the case where
out of order packets need to be transmitted.
Other drivers obtain the entire TLS record for the specific skb to
provide as context to hardware for encryption. However, other designs
may also want to keep the hardware state intact and perform the
out of order encryption entirely on the host.
To achieve this, export the already existing software encryption
fallback path so drivers could access this.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently drivers have to ensure the alignment of their tls state
structure, which leads to unnecessary layers of getters and
encapsulated structures in each driver.
Simplify all this by marking the driver state as aligned (driver_state
members are currently aligned, so no hole is added, besides ALIGN in
TLS_OFFLOAD_CONTEXT_SIZE_RX/TX would reserve this extra space, anyway.)
With that we can add a common accessor to the core.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
8 bytes of driver state has been enough so far, but for drivers
which have to store 8 byte handle it's no longer practical to
store the state directly in the context.
Drivers generally don't need much extra state on RX side, while
TX side has to be tracking TCP sequence numbers. Split the
lengths of max driver state size on RX and TX.
The struct tls_offload_context_tx currently stands at 616 bytes and
struct tls_offload_context_rx stands at 368 bytes. Upcoming work
will consume extra 8 bytes in both for kernel-driven resync.
This means that we can bump TX side to 16 bytes and still fit
into the same number of cache lines but on RX side we would be 8
bytes over.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Subsequent patches will add support for more TX metadata fields.
Prepare for this by handling an additional double word - firmware
handle as metadata type 7.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add FW ABI defines and code for basic init of TLS offload.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Parse TLV containing a bitmask of supported crypto operations.
The TLV contains a capability bitmask (supported operations)
and enabled bitmask. Each operation describes the crypto
protocol quite exhaustively (protocol, AEAD, direction).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FW may prefer to handle some communication via a mailbox
or the vNIC may simply not have a control queue (VFs).
Add a way of exchanging ccm-compatible messages via a
mailbox.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Parse the mailbox TLV. When control message queue is not available
we can fall back to passing the control messages via the vNIC
mailbox.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We will need to release the bar lock from a workqueue
so move from a mutex to a semaphore. This lock should
not be too hot. Unfortunately semaphores don't have
lockdep support.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently if we need to modify the head of the skb and allocation
fails we would free the skb and not increment the error counter.
Make sure all errors are counted.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add 1000BaseX to the link modes which are detected based on the
MII_ESTATUS register as per 802.3 Clause 22. This allows PHYs which
support 1000BaseX to work properly with drivers using phylink.
Previously 1000BaseX support was not detected, and if that was the only
mode the PHY indicated support for, phylink would refuse to attach it
due to the list of supported modes being empty.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
- Fix crashes when accessing PCI devices on some machines like C240 and
J5000. The crashes were triggered because we replaced cache flushes
by nops in the alternative coding where we shouldn't for some
machines.
- Dave fixed a race in the usage of the sr1 space register when used to
load the coherence index.
- Use the hardware lpa instruction to to load the physical address of
kernel virtual addresses in the iommu driver code.
- The kernel may fail to link when CONFIG_MLONGCALLS isn't set. Solve
that by rearranging functions in the final vmlinux executeable.
- Some defconfig cleanups and removal of compiler warnings.
* 'parisc-5.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix crash due alternative coding for NP iopdir_fdc bit
parisc: Use lpa instruction to load physical addresses in driver code
parisc: configs: Remove useless UEVENT_HELPER_PATH
parisc: Use implicit space register selection for loading the coherence index of I/O pdirs
parisc: Fix compiler warnings in float emulation code
parisc/slab: cleanup after /proc/slab_allocators removal
parisc: Allow building 64-bit kernel without -mlong-calls compiler option
parisc: Kconfig: remove ARCH_DISCARD_MEMBLOCK
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes a regression that breaks the jitterentropy RNG and a
potential memory leak in hmac"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: hmac - fix memory leak in hmac_init_tfm()
crypto: jitterentropy - change back to module_init()
|
|
Pull xfs fixes from Darrick Wong:
"Here are a couple more bug fixes for 5.2. Changes since last update:
- Fix some forgotten strings in a log debugging function
- Fix incorrect unit conversion in online fsck code"
* tag 'xfs-5.2-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: inode btree scrubber should calculate im_boffset correctly
xfs: fix broken log reservation debugging
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2
Pull gfs2 fix from Andreas Gruenbacher:
"A revert for a patch that turned out to be broken"
* tag 'gfs2-v5.2.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
Revert "gfs2: Replace gl_revokes with a GLF flag"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs fixes from Miklos Szeredi:
"Here's one fix for a class of bugs triggered by syzcaller, and one
that makes xfstests fail less"
* tag 'ovl-fixes-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: doc: add non-standard corner cases
ovl: detect overlapping layers
ovl: support the FS_IOC_FS[SG]ETXATTR ioctls
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse fixes from Miklos Szeredi:
"This fixes a leaked inode lock in an error cleanup path and a data
consistency issue with copy_file_range().
It also adds a new flag for the WRITE request that allows userspace
filesystems to clear suid/sgid bits on the file if necessary"
* tag 'fuse-fixes-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: extract helper for range writeback
fuse: fix copy_file_range() in the writeback case
fuse: add FUSE_WRITE_KILL_PRIV
fuse: fallocate: fix return with locked inode
|
|
Pull NFS client fixes from Anna Schumaker:
"These are mostly stable bugfixes found during testing, many during the
recent NFS bake-a-thon.
Stable bugfixes:
- SUNRPC: Fix regression in umount of a secure mount
- SUNRPC: Fix a use after free when a server rejects the RPCSEC_GSS credential
- NFSv4.1: Again fix a race where CB_NOTIFY_LOCK fails to wake a waiter
- NFSv4.1: Fix bug only first CB_NOTIFY_LOCK is handled
Other bugfixes:
- xprtrdma: Use struct_size() in kzalloc()"
* tag 'nfs-for-5.2-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
NFSv4.1: Fix bug only first CB_NOTIFY_LOCK is handled
NFSv4.1: Again fix a race where CB_NOTIFY_LOCK fails to wake a waiter
SUNRPC: Fix a use after free when a server rejects the RPCSEC_GSS credential
SUNRPC fix regression in umount of a secure mount
xprtrdma: Use struct_size() in kzalloc()
|
|
Fix sparse warning:
drivers/net/ethernet/mscc/ocelot_ace.c:96:3:
warning: symbol 'vcap_data_t' was not declared. Should it be static?
'vcap_data_t' never used so can be removed
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In following sequences, child devices created while removing mdev parent
device can be left out, or it may lead to race of removing half
initialized child mdev devices.
issue-1:
--------
cpu-0 cpu-1
----- -----
mdev_unregister_device()
device_for_each_child()
mdev_device_remove_cb()
mdev_device_remove()
create_store()
mdev_device_create() [...]
device_add()
parent_remove_sysfs_files()
/* BUG: device added by cpu-0
* whose parent is getting removed
* and it won't process this mdev.
*/
issue-2:
--------
Below crash is observed when user initiated remove is in progress
and mdev_unregister_driver() completes parent unregistration.
cpu-0 cpu-1
----- -----
remove_store()
mdev_device_remove()
active = false;
mdev_unregister_device()
parent device removed.
[...]
parents->ops->remove()
/*
* BUG: Accessing invalid parent.
*/
This is similar race like create() racing with mdev_unregister_device().
BUG: unable to handle kernel paging request at ffffffffc0585668
PGD e8f618067 P4D e8f618067 PUD e8f61a067 PMD 85adca067 PTE 0
Oops: 0000 [#1] SMP PTI
CPU: 41 PID: 37403 Comm: bash Kdump: loaded Not tainted 5.1.0-rc6-vdevbus+ #6
Hardware name: Supermicro SYS-6028U-TR4+/X10DRU-i+, BIOS 2.0b 08/09/2016
RIP: 0010:mdev_device_remove+0xfa/0x140 [mdev]
Call Trace:
remove_store+0x71/0x90 [mdev]
kernfs_fop_write+0x113/0x1a0
vfs_write+0xad/0x1b0
ksys_write+0x5a/0xe0
do_syscall_64+0x5a/0x210
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Therefore, mdev core is improved as below to overcome above issues.
Wait for any ongoing mdev create() and remove() to finish before
unregistering parent device.
This continues to allow multiple create and remove to progress in
parallel for different mdev devices as most common case.
At the same time guard parent removal while parent is being accessed by
create() and remove() callbacks.
create()/remove() and unregister_device() are synchronized by the rwsem.
Refactor device removal code to mdev_device_remove_common() to avoid
acquiring unreg_sem of the parent.
Fixes: 7b96953bc640 ("vfio: Mediated device Core driver")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
If device is removal is initiated by two threads as below, mdev core
attempts to create a syfs remove file on stale device.
During this flow, below [1] call trace is observed.
cpu-0 cpu-1
----- -----
mdev_unregister_device()
device_for_each_child
mdev_device_remove_cb
mdev_device_remove
user_syscall
remove_store()
mdev_device_remove()
[..]
unregister device();
/* not found in list or
* active=false.
*/
sysfs_create_file()
..Call trace
Now that mdev core follows correct device removal sequence of the linux
bus model, remove shouldn't fail in normal cases. If it fails, there is
no point of creating a stale file or checking for specific error status.
kernel: WARNING: CPU: 2 PID: 9348 at fs/sysfs/file.c:327
sysfs_create_file_ns+0x7f/0x90
kernel: CPU: 2 PID: 9348 Comm: bash Kdump: loaded Not tainted
5.1.0-rc6-vdevbus+ #6
kernel: Hardware name: Supermicro SYS-6028U-TR4+/X10DRU-i+, BIOS 2.0b
08/09/2016
kernel: RIP: 0010:sysfs_create_file_ns+0x7f/0x90
kernel: Call Trace:
kernel: remove_store+0xdc/0x100 [mdev]
kernel: kernfs_fop_write+0x113/0x1a0
kernel: vfs_write+0xad/0x1b0
kernel: ksys_write+0x5a/0xe0
kernel: do_syscall_64+0x5a/0x210
kernel: entry_SYSCALL_64_after_hwframe+0x49/0xbe
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Currently, the process issuing a "start" command on the pktgen procfs
interface, acquires the pktgen thread lock and never release it, until
all pktgen threads are completed. The above can blocks indefinitely any
other pktgen command and any (even unrelated) netdevice removal - as
the pktgen netdev notifier acquires the same lock.
The issue is demonstrated by the following script, reported by Matteo:
ip -b - <<'EOF'
link add type dummy
link add type veth
link set dummy0 up
EOF
modprobe pktgen
echo reset >/proc/net/pktgen/pgctrl
{
echo rem_device_all
echo add_device dummy0
} >/proc/net/pktgen/kpktgend_0
echo count 0 >/proc/net/pktgen/dummy0
echo start >/proc/net/pktgen/pgctrl &
sleep 1
rmmod veth
Fix the above releasing the thread lock around the sleep call.
Additionally we must prevent racing with forcefull rmmod - as the
thread lock no more protects from them. Instead, acquire a self-reference
before waiting for any thread. As a side effect, running
rmmod pktgen
while some thread is running now fails with "module in use" error,
before this patch such command hanged indefinitely.
Note: the issue predates the commit reported in the fixes tag, but
this fix can't be applied before the mentioned commit.
v1 -> v2:
- no need to check for thread existence after flipping the lock,
pktgen threads are freed only at net exit time
-
Fixes: 6146e6a43b35 ("[PKTGEN]: Removes thread_{un,}lock() macros.")
Reported-and-tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we do a clk_get() for a clock that does not exists, we have
_ti_omap4_clkctrl_xlate() return uninitialized data if no match
is found. This can be seen in some cases with SLAB_DEBUG enabled:
Unable to handle kernel paging request at virtual address 5a5a5a5a
...
clk_hw_create_clk.part.33
sysc_notifier_call
notifier_call_chain
blocking_notifier_call_chain
device_add
Let's fix this by setting a found flag only when we find a match.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fixes: 88a172526c32 ("clk: ti: add support for clkctrl clocks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
When a valid MAC address is not found the current messages
are shown:
fec 2188000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
fec 2188000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: aa:9f:25:eb:7e:aa
Since the network device has not been registered at this point, it is better
to use dev_err()/dev_info() instead, which will provide cleaner log
messages like these:
fec 2188000.ethernet: Invalid MAC address: 00:00:00:00:00:00
fec 2188000.ethernet: Using random MAC address: aa:9f:25:eb:7e:aa
Tested on a imx6dl-pico-pi board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The monolithic hash_lock could cause huge contention when
inserting/deletiing vxlan_fdbs into the fdb_head.
Use FDB_HASH_SIZE hash_locks to protect insertions/deletions
of vxlan_fdbs into the fdb_head hash table.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Litao jiao <jiaolitao@raisecom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull ADFS cleanups/fixes from Russell King:
"As a result of some of Al Viro's great work, here are a few cleanups
with fixes for adfs:
- factor out filename comparison, so we can be sure that
adfs_compare() (used for namei compare) and adfs_match() (used for
lookup) have the same behaviour.
- factor out filename lowering (which is not the same as tolower()
which will lower top-bit-set characters) to ensure that we have the
same behaviour when comparing filenames as when we hash them.
- factor out the object fixups, so we are applying all fixups to
directory objects in the same way, independent of the disk format.
- factor out the object name fixup (into the previously factored out
function) to ensure that filenames are appropriately translated -
for example, adfs allows '/' in filenames, which being the Unix
path separator, need to be translated to a different character,
which is normally '.' (DOS 8.3 filenames represent the . as a / on
adfs, so this is the expected reverse translation.)
- remove filename truncation; Al asked about this and apparently the
decision is to remove it. In any case, adfs's truncation was buggy,
so this rids us of that bug by removing the truncation feature.
- we now have only one location which adds the "filetype" suffix to
the filename, so there's no point that code being out of line.
- since we translate '/' into '.', an adfs filename of "/" or "//"
would end up being translated to "." and ".." which have special
meanings. In this case, change the first character to "^" to avoid
these special directory names being abused"
* tag 'for-rc-adfs' of git://git.armlinux.org.uk/~rmk/linux-arm:
fs/adfs: fix filename fixup handling for "/" and "//" names
fs/adfs: move append_filetype_suffix() into adfs_object_fixup()
fs/adfs: remove truncated filename hashing
fs/adfs: factor out filename fixup
fs/adfs: factor out object fixups
fs/adfs: factor out filename case lowering
fs/adfs: factor out filename comparison
|
|
Use a safe strscpy call to copy the ethtool stat strings into the
relevant buffers, instead of a memcpy that will be accessing
out-of-bound data.
Fixes: 118d6298f6f0 ("net: mvpp2: add ethtool GOP statistics")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in a NL_SET_ERR_MSG message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the following tests last for several hours, the problem will occur.
Server:
rds-stress -r 1.1.1.16 -D 1M
Client:
rds-stress -r 1.1.1.14 -s 1.1.1.16 -D 1M -T 30
The following will occur.
"
Starting up....
tsks tx/s rx/s tx+rx K/s mbi K/s mbo K/s tx us/c rtt us cpu
%
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
"
>From vmcore, we can find that clean_list is NULL.
>From the source code, rds_mr_flushd calls rds_ib_mr_pool_flush_worker.
Then rds_ib_mr_pool_flush_worker calls
"
rds_ib_flush_mr_pool(pool, 0, NULL);
"
Then in function
"
int rds_ib_flush_mr_pool(struct rds_ib_mr_pool *pool,
int free_all, struct rds_ib_mr **ibmr_ret)
"
ibmr_ret is NULL.
In the source code,
"
...
list_to_llist_nodes(pool, &unmap_list, &clean_nodes, &clean_tail);
if (ibmr_ret)
*ibmr_ret = llist_entry(clean_nodes, struct rds_ib_mr, llnode);
/* more than one entry in llist nodes */
if (clean_nodes->next)
llist_add_batch(clean_nodes->next, clean_tail, &pool->clean_list);
...
"
When ibmr_ret is NULL, llist_entry is not executed. clean_nodes->next
instead of clean_nodes is added in clean_list.
So clean_nodes is discarded. It can not be used again.
The workqueue is executed periodically. So more and more clean_nodes are
discarded. Finally the clean_list is NULL.
Then this problem will occur.
Fixes: 1bc144b62524 ("net, rds, Replace xlist in net/rds/xlist.h with llist")
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Olivier Matz says:
====================
ipv6: fix EFAULT on sendto with icmpv6 and hdrincl
The following code returns EFAULT (Bad address):
s = socket(AF_INET6, SOCK_RAW, IPPROTO_ICMPV6);
setsockopt(s, SOL_IPV6, IPV6_HDRINCL, 1);
sendto(ipv6_icmp6_packet, addr); /* returns -1, errno = EFAULT */
The problem is fixed in the second patch. The first one aligns the
code to ipv4, to avoid a race condition in the second patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following code returns EFAULT (Bad address):
s = socket(AF_INET6, SOCK_RAW, IPPROTO_ICMPV6);
setsockopt(s, SOL_IPV6, IPV6_HDRINCL, 1);
sendto(ipv6_icmp6_packet, addr); /* returns -1, errno = EFAULT */
The IPv4 equivalent code works. A workaround is to use IPPROTO_RAW
instead of IPPROTO_ICMPV6.
The failure happens because 2 bytes are eaten from the msghdr by
rawv6_probe_proto_opt() starting from commit 19e3c66b52ca ("ipv6
equivalent of "ipv4: Avoid reading user iov twice after
raw_probe_proto_opt""), but at that time it was not a problem because
IPV6_HDRINCL was not yet introduced.
Only eat these 2 bytes if hdrincl == 0.
Fixes: 715f504b1189 ("ipv6: add IPV6_HDRINCL option for raw sockets")
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As it was done in commit 8f659a03a0ba ("net: ipv4: fix for a race
condition in raw_sendmsg") and commit 20b50d79974e ("net: ipv4: emulate
READ_ONCE() on ->hdrincl bit-field in raw_sendmsg()") for ipv4, copy the
value of inet->hdrincl in a local variable, to avoid introducing a race
condition in the next commit.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
