| Age | Commit message (Collapse) | Author |
|---|
|
Support for multiple lines in SPI framework has been picked[1].
[1]: http://comments.gmane.org/gmane.linux.kernel.spi.devel/14420
Hence, adapting ti qspi driver to support multiple data lines for read.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
Pointers passed to ARAnyM NatFeat calls should be physical addresses,
not virtual addresses. This worked before because on Atari, physical and
virtual kernel addresses are the same, as long as normal kernel memory
is concerned.
Correct the few remaining places where virtual addresses were used.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
When running a multi-platform kernel on Atari, warning messages like
the following may be printed:
WARNING: at /root/linux-3.10.1/init/main.c:698 do_one_initcall+0x12e/0x13a()
initcall param_sysfs_init+0x0/0x1a4 returned with disabled interrupts
This is caused by the different definitions of ALLOWINT for Atari and
other platforms:
#if defined(MACH_ATARI_ONLY)
#define ALLOWINT (~0x500)
#else
#define ALLOWINT (~0x700)
#endif
On Atari, we want to disable the high-frequency HSYNC interrupt:
- On Atari-only kernels, this is handled completely through ALLOWINT,
- On multi-platform kernels, this is handled by disabling the HSYNC
interrupt from the interrupt handler.
However, as in the latter case arch_irqs_disabled_flags() didn't ignore the
disabling of the HSYNC interrupt, irqs_disabled() would detect false
positives.
Ignore the HSYNC interrupt when running on Atari to fix this.
For single-platform kernels this test is optimized away by the compiler.
Reported-by: Thorsten Glaser <tg@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Thorsten Glaser <tg@debian.org>
|
|
mac80211 currently sets WIPHY_FLAG_SUPPORTS_SCHED_SCAN based on whether
the start_sched_scan operation is supported or not, but that will not
be correct for all drivers, we're adding scheduled scan to the iwlmvm
driver but it depends on firmware support.
Therefore, move setting WIPHY_FLAG_SUPPORTS_SCHED_SCAN into the drivers
so that they can control it regardless of implementing the operation.
This currently only affects the TI drivers since they're the only ones
implementing scheduled scan (in a mac80211 driver.)
Acked-by: Luciano Coelho <luca@coelho.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
use exact SoC revision instead of wildcard describing
the compatible property requirement in the binding
document. This will make the binding more clearer.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Just one patch that soaked for quite a bit to fix a resume issue,
resulting in gpu hangs (or worse) due to tlb containing garbage.
* tag 'drm-intel-fixes-2013-08-23' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Invalidate TLBs for the rings after a reset
|
|
If NO_DMA=y:
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_mmap’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:204: error: implicit declaration of function ‘dma_mmap_coherent’
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_get_base_sgt’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:387: error: implicit declaration of function ‘dma_get_sgtable’
Commit da508f5799659241a359e2d07abb8af905f6291c ("[media] media/v4l2:
VIDEOBUF2_DMA_CONTIG should depend on HAS_DMA") added a dependency on
HAS_DMA to VIDEO_SH_VEU, as it selects VIDEOBUF2_DMA_CONTIG.
However, this got lost in the merge conflict resolution in commit
df90e2258950fd631cdbf322c1ee1f22068391aa ("Merge branch 'devel-for-v3.10'
into v4l_for_linus").
Re-add the dependency to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The KWorld UB445-U is similar to the UB430-AF but with a Samsung S5H1411
frontend. Luckily all of the hardware is already well supported, just the
device and USB ids need to be added to get it to work.
Signed-off-by: Johannes Erdfelt <johannes@erdfelt.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
At least technisat-usb2.c doesn't set these...
Signed-off-by: Juergen Lock <nox@jelal.kn-bremen.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
This follows what has already been done for the DeviceTree helpers. Move
the ACPI helpers from drivers/acpi/acpi_i2c.c to the I2C core and update
documentation accordingly.
This also solves a problem reported by Jerry Snitselaar that we can't build
the ACPI I2C helpers as a module.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
I2C of helpers used to live in of_i2c.c but experience (from SPI) shows
that it is much cleaner to have this in the core. This also removes a
circular dependency between the helpers and the core, and so we can
finally register child nodes in the core instead of doing this manually
in each driver. So, fix the drivers and documentation, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
All the Armada XP (mv78230, mv78260 and mv78460) have a silicon issue
in the I2C controller which violate the i2c repeated start
timing. The I2C standard requires a minimum of 4.7us for the repeated
start condition whereas the I2C controller of the Armada XP this time
is 2.9us.
So this patch adds a 5us delay for the start case only if the
the compatible i2c-mv78230 is set.
Based on the initals patches from Zbigniew Bodek
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Zbigniew Bodek <zbb@semihalf.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The I2C Transaction Generator offloads CPU from managing I2C
transfer step by step.
This feature is currently only available on Armada XP, so usage of
this mechanism is activated through device tree.
Based on the work of Piotr Ziecik and rewrote to use the new way of
handling multiples i2c messages.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Just return once a match found makes the code simpler and shorter.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pin control utility functions provides the function for creating
map lists.
In place of implementing APIs locally in Tegra pin control driver
for creating map lists, use the utility functions. This reduces
the code size and avoid duplication.
Changes from V1:
- Rebased change on top of V1.
- Use pinctrl_utils_dt_free_map
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add support to pass the config type like GROUP or PIN when using
the utils or generic pin configuration APIs. This will make the
APIs more generic.
Added additional inline APIs such that it can be use directly as
callback for the pinctrl_ops.
Changes from V1:
- Remove separate implementation for pins and group for
pinctrl_utils_dt_free_map and improve this function
to support both i.e. PINS and GROUPs.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Calling pinctrl_register() means that the driver is fully initialized
and might accept pinmux/pinconf requests, so pin groups must be parsed
before.
This patch fixes this problem by moving device tree parsing before call
to pinctrl_register(). In addition, this fixes support for hogs on
pin controllers handled by pinctrl-samsung driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The device family is called Palmas so there should be a 's' on the end of
the name.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The symbol SPEAr310_pinctrl_of_match does not exist at all. Fix it.
We didn't hit the compile error because this driver can only be built-in now.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Allwinner A20 is pin-compatible with the older A10, so the two pin
set are quite similar. However, since the A20 has new features, we can't
just use the A10 pin set as is, and we need to define our own for the
A20.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Allwinner A31 SoC uses the same IP than the one found in the
A10/A13, with only different pins. Add the pins and the associated
functions found in the A31.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some pin functions in the array were not indented like the other
functions in this array. Fix this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The implementation in pinctrl_register_one_pin() ensures pindesc->name is always
not NULL before insert the pindesc to radix tree.
If the desc return from pin_desc_get is not NULL, desc->name is always not NULL.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
pinctrl_register() returns NULL on error, fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Hold pctldev->mutex mutex_lock when traverse the list.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This one is missed in commit 44d5f7bb "pinctrl: sink pinctrldev_list_mutex".
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
the old codes defined uart0_nostreamctrl_pins, but missed pingroup
and padmux definition for it. this patch fixes it.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
make the Freescale ethernet driver get, prepare and enable the FEC clock
during probe(); disable and unprepare the clock upon remove(), put is
done by the devm approach; hold a reference to the clock over the period
of use.
clock lookup is non-fatal as not all platforms provide clock specs in
their device tree; failure to enable specified clocks is fatal.
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 720a43efd30f04a0a492c85fb997361c44fbae05
(drivers:net: Remove unnecessary OOM messages after netdev_alloc_skb)
there is a build warning:
drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c: In function 'tx_skb_align_workaround':
drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c:586:26: warning: unused variable 'fep'
Fix it.
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can simply use the %pISc format specifier that was recently added
and thus remove some code that distinguishes between IPv4 and IPv6.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
into cpsw
Marc Kleine-Budde says:
====================
another pull-request for net-next. It consists of two patches by Libo
Chen, the at91 and flexcan driver make use of platform_set_drvdata()
rather than open coding it. Chen Gang improves the error checking in
the c_can_platform driver's probe function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is needed when the cpsw driver is built as module.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IP sends device configuration (see inet_fill_link_af) as an array
in the netlink information, but the indices in that array are not
exposed to userspace through any current santized header file.
It was available back in 2.6.32 (in /usr/include/linux/sysctl.h)
but was broken by:
commit 02291680ffba92e5b5865bc0c5e7d1f3056b80ec
Author: Eric W. Biederman <ebiederm@xmission.com>
Date: Sun Feb 14 03:25:51 2010 +0000
net ipv4: Decouple ipv4 interface parameters from binary sysctl numbers
Eric was solving the sysctl problem but then the indices were re-exposed
by a later addition of devconf support for IPV4
commit 9f0f7272ac9506f4c8c05cc597b7e376b0b9f3e4
Author: Thomas Graf <tgraf@infradead.org>
Date: Tue Nov 16 04:32:48 2010 +0000
ipv4: AF_INET link address family
Putting them in /usr/include/linux/ip.h seemed the logical match
for the DEVCONF_ definitions for IPV6 in /usr/include/linux/ip6.h
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rfc 4861 says the Redirected Header option is optional, so
the kernel should not drop the Redirect Message that has no
Redirected Header option. In this patch, the function
ip6_redirect_no_header() is introduced to deal with that
condition.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
|
|
commit fba875591 ("disable TX in be_close()") disabled TX in be_close()
to protect be_xmit() from touching freed up queues in the AER recovery
flow. But, TX must be disabled *before* cleaning up TX completions in
the close() path, not after. This allows be_tx_compl_clean() to free up
all TX-req skbs that were notified to the HW.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reported-by: Kirill Tkhai <tkhai@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tcp_probe currently only supports analysis of IPv4 connections.
Therefore, it would be nice to have IPv6 supported as well. Since we
have the recently added %pISpc specifier that is IPv4/IPv6 generic,
build related sockaddress structures from the flow information and
pass this to our format string. Tested with SSH and HTTP sessions
on IPv4 and IPv6.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patches fixes a rather unproblematic function signature mismatch
as the const specifier was missing for the th variable; and next to
that it adds a build-time assertion so that future function signature
mismatches for kprobes will not end badly, similarly as commit 22222997
("net: sctp: add build check for sctp_sf_eat_sack_6_2/jsctp_sf_eat_sack")
did it for SCTP.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is helpful to sometimes know the TCP window sizes of an established
socket e.g. to confirm that window scaling is working or to tweak the
window size to improve high-latency connections, etc etc. Currently the
TCP snooper only exports the send window size, but not the receive window
size. Therefore, also add the receive window size to the end of the
output line.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
1) Some constifications, from Mathias Krause.
2) Catch bugs if a hold timer is still active when xfrm_policy_destroy()
is called, from Fan Du.
3) Remove a redundant address family checking, from Fan Du.
4) Make xfrm_state timer monotonic to be independent of system clock changes,
from Fan Du.
5) Remove an outdated comment on returning -EREMOTE in the xfrm_lookup(),
from Rami Rosen.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull DT/core/cpufreq cpu_ofnode updates for v3.12 from Sudeep KarkadaNagesha.
* 'cpu_of_node' of git://linux-arm.org/linux-skn:
cpufreq: pmac32-cpufreq: remove device tree parsing for cpu nodes
cpufreq: pmac64-cpufreq: remove device tree parsing for cpu nodes
cpufreq: maple-cpufreq: remove device tree parsing for cpu nodes
cpufreq: arm_big_little: remove device tree parsing for cpu nodes
cpufreq: kirkwood-cpufreq: remove device tree parsing for cpu nodes
cpufreq: spear-cpufreq: remove device tree parsing for cpu nodes
cpufreq: highbank-cpufreq: remove device tree parsing for cpu nodes
cpufreq: cpufreq-cpu0: remove device tree parsing for cpu nodes
cpufreq: imx6q-cpufreq: remove device tree parsing for cpu nodes
drivers/bus: arm-cci: avoid parsing DT for cpu device nodes
ARM: mvebu: remove device tree parsing for cpu nodes
ARM: topology: remove hwid/MPIDR dependency from cpu_capacity
of/device: add helper to get cpu device node from logical cpu index
driver/core: cpu: initialize of_node in cpu's device struture
ARM: DT/kernel: define ARM specific arch_match_cpu_phys_id
of: move of_get_cpu_node implementation to DT core library
powerpc: refactor of_get_cpu_node to support other architectures
openrisc: remove undefined of_get_cpu_node declaration
microblaze: remove undefined of_get_cpu_node declaration
|
|
|
|
Field predicted_us value can never exceed expected_us value, but it has
a potentially larger type. As there is no need for additional 32 bits of
zeroes on 32 bit plaforms, change the type of predicted_us to match the
type of expected_us.
Field correction_factor is used to store a value that cannot exceed the
product of RESOLUTION and DECAY (default 1024*8 = 8192). The constants
cannot in practice be incremented to such values, that they'd overflow
unsigned int even on 32 bit systems, so the type is changed to avoid
unnecessary 64 bit arithmetic on 32 bit systems.
One multiplication of (now) 32 bit values needs an added cast to avoid
truncation of the result and has been added.
In order to avoid another multiplication from 32 bit domain to 64 bit
domain, the new correction_factor calculation has been changed from
new = old * (DECAY-1) / DECAY
to
new = old - old / DECAY,
which with infinite precision would yeild exactly the same result, but
now changes the direction of rounding. The impact is not significant as
the maximum accumulated difference cannot exceed the value of DECAY,
which is relatively small compared to product of RESOLUTION and DECAY
(8 / 8192).
Signed-off-by: Tuukka Tikkanen <tuukka.tikkanen@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The menu governor has a number of tunable constants that may be changed
in the source. If certain combination of values are chosen, an overflow
is possible when the correction_factor is being recalculated.
This patch adds a warning regarding this possibility and describes the
change needed for fixing the issue. The change should not be permanently
enabled, as it will hurt performance when it is not needed.
Signed-off-by: Tuukka Tikkanen <tuukka.tikkanen@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The menu governor uses a static function get_typical_interval() to
try to detect a repeating pattern of wakeups. The previous interval
durations are stored as an array of unsigned ints, but the arithmetic
in the function is performed exclusively as 64 bit values, even when
the value stored in a variable is known not to exceed unsigned int,
which may be smaller and more efficient on some platforms.
This patch changes the types of varibles used to store some
intermediates, the maximum and and the cutoff threshold to unsigned
ints. Average and standard deviation are still treated as 64 bit values,
even when the values are known to be within the domain of unsigned int,
to avoid casts to ensure correct integer promotion for arithmetic
operations.
Signed-off-by: Tuukka Tikkanen <tuukka.tikkanen@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Struct menu_device member intervals is declared as u32, but the value
stored is (unsigned) int. The type is changed to match the value being
stored.
Signed-off-by: Tuukka Tikkanen <tuukka.tikkanen@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The function get_typical_interval() initializes a number of variables
that are immediately after declarations assigned constant values.
In addition, there are multiple assignments on a single line, which
is explicitly forbidden by Documentation/CodingStyle.
This patch removes redundant initial values for the variables and
breaks up the multiple assignment line.
Signed-off-by: Tuukka Tikkanen <tuukka.tikkanen@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
get_typical_interval() uses int_sqrt() in calculation of standard
deviation. The formal parameter of int_sqrt() is unsigned long, which
may on some platforms be smaller than the 64 bit unsigned integer used
as the actual parameter. The overflow can occur frequently when actual
idle period lengths are in hundreds of milliseconds.
This patch adds a check for such overflow and rejects the candidate
average when an overflow would occur.
Signed-off-by: Tuukka Tikkanen <tuukka.tikkanen@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
