| Age | Commit message (Collapse) | Author |
|---|
|
Add read/write calls for Adaptive Sync SDP.
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240322031157.3823909-10-mitulkumar.ajitkumar.golani@intel.com
|
|
Compute vrr_vsync_start/end, which sets the position
for hardware to send the Vsync at a fixed position
relative to the end of the Vblank.
--v2:
- Updated VSYNC_START/END macros to VRR_VSYNC_START/END. (Ankit)
- Updated bit fields of VRR_VSYNC_START/END. (Ankit)
--v3:
- Add PIPE_CONF_CHECK_I(vrr.vsync_start/end).
- Read/write vrr_vsync params only when we intend to send
adaptive_sync sdp.
--v4:
- Use VRR_SYNC_START/END macros correctly.
--v5:
- Send AS SDP only when VRR is enabled.
--v6:
- Add TRANS_VRR_VSYNC before enabling VRR as per bspec. (Ankit)
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240322031157.3823909-9-mitulkumar.ajitkumar.golani@intel.com
|
|
Enable infoframe and add state checker for Adaptive Sync
SDP enablement.
--v1:
- crtc_state->infoframes.enable, to add on correct place holder.
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240322031157.3823909-8-mitulkumar.ajitkumar.golani@intel.com
|
|
Add necessary function definitions to compute AS SDP data.
The new intel_dp_compute_as_sdp function computes AS SDP
values based on the display configuration, ensuring proper
handling of Variable Refresh Rate (VRR).
--v2:
- Added DP_SDP_ADAPTIVE_SYNC to infoframe_type_to_idx(). [Ankit]
- Separated patch for intel_read/write_dp_sdp. [Ankit]
- _HSW_VIDEO_DIP_ASYNC_DATA_A should be from ADL onward. [Ankit]
- Fixed indentation issues. [Ankit]
--v3:
- Added VIDEO_DIP_ENABLE_AS_HSW flag to intel_dp_set_infoframes.
--v4:
- Added HAS_VRR check before writing AS SDP.
--v5:
Added missed HAS_VRR check before reading AS SDP.
--v6:
- Used Adaptive Sync sink status as a check for read/write SDP. (Ankit)
--v7:
- Remove as_sdp_enable from crtc_state.
- Add a comment mentioning current support of
DP_AS_SDP_AVT_FIXED_VTOTAL.
- Add state checker for AS_SDP infoframe enable.
--v8:
- Drop conn_state from intel_dp_compute_as_sdp, as not used.
- Remove fullstop in subject line.
--v9:
- Add vrr.enable instead of is_in_vrr_range.
--v10:
- remove vrefresh and connector, as they are no longer required.
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240322031157.3823909-7-mitulkumar.ajitkumar.golani@intel.com
|
|
Add a wrapper function to check if both the source and
sink support Adaptive Sync SDP.
--v1:
Just use drm/i915/dp in subject line.
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240322031157.3823909-6-mitulkumar.ajitkumar.golani@intel.com
|
|
Add the necessary structures and functions to handle reading and
unpacking Adaptive Sync Secondary Data Packets. Also add support
to write and pack AS SDP.
--v2:
- Correct use of REG_BIT and REG_GENMASK. [Jani]
- Use as_sdp instead of async. [Jani]
- Remove unrelated comments and changes. [Jani]
- Correct code indent. [Jani]
--v3:
- Update definition names for AS SDP which are starting from
HSW, as these defines are applicable for ADLP+.(Ankit)
--v4:
- Remove as_sdp_mode from crtc_state.
- Drop metadata keyword.
- For consistency, update ADL_ prefix or post fix as required.
--v5:
- Check if AS_SDP bit is set in crtc_state->infoframes.enable. If not
return.
- Check for HAS_AS_SDP() before setting VIDEO_DIP_ENABLE_AS_ADL mask.
--v6:
- Rename intel_read_dp_infoframe_as_sdp to intel_read_dp_as_sdp.
--v7:
- Add read back for length and vtotal correction.
--v8:
- Use as_sdp->target_rr & 0xFF.
- Shift by 8 instead of 32, and drop casting to u64.
- Remove changes which are does not belong to this patch.
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240322031157.3823909-5-mitulkumar.ajitkumar.golani@intel.com
|
|
Add crtc state dump for Adaptive Sync SDP to know which
crtc specifically caused the failure.
--v1:
- Rebase Patches to latest.
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240322031157.3823909-4-mitulkumar.ajitkumar.golani@intel.com
|
|
Add structure representing Adaptive Sync Secondary Data Packet (AS SDP).
Also, add Adaptive Sync SDP logging in drm_dp_helper.c to facilitate
debugging.
--v2:
- Update logging. [Jani, Ankit]
- Use 'as_sdp' instead of 'async' [Ankit]
- Correct define placeholders to where they are actually used. [Jani]
- Update members in 'as_sdp' structure to make it uniform. [Jani]
--v3:
- Added changes to dri-devel mailing list. No code changes.
--v4:
- Instead of directly using operation mode, use an enum to accommodate
all operation modes (Ankit).
--v5:
Nit-pick changes to commit message.
--v6:
- Add correct place holder and name change for AS_SDP_OP_MODE.
- Separate i915 changes from drm changes.
- Remove extra lines.
--v7:
- Add drm/dp in subject line (Ankit)
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240322031157.3823909-3-mitulkumar.ajitkumar.golani@intel.com
|
|
The __vmalloc_start_set declaration is in a header that is not included
in numa_32.c in current linux-next:
arch/x86/mm/numa_32.c: In function 'initmem_init':
arch/x86/mm/numa_32.c:57:9: error: '__vmalloc_start_set' undeclared (first use in this function)
57 | __vmalloc_start_set = true;
| ^~~~~~~~~~~~~~~~~~~
arch/x86/mm/numa_32.c:57:9: note: each undeclared identifier is reported only once for each function it appears in
Add an explicit #include.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20240403202344.3463169-1-arnd@kernel.org
|
|
Add an API that indicates support for Adaptive Sync SDP in
the sink, which can be utilized by the rest of the DP programming.
--v1:
- Format commit message properly.
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240322031157.3823909-2-mitulkumar.ajitkumar.golani@intel.com
|
|
The call to clk_enable() in gemini_sata_start_bridge() can fail.
Add a check to detect such failure.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
Building with W=1 shows a warning for an unused variable when CONFIG_PCI
is diabled:
drivers/ata/sata_mv.c:790:35: error: unused variable 'mv_pci_tbl' [-Werror,-Wunused-const-variable]
static const struct pci_device_id mv_pci_tbl[] = {
Move the table into the same block that containsn the pci_driver
definition.
Fixes: 7bb3c5290ca0 ("sata_mv: Remove PCI dependency")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
mana_get_rxbuf_cfg() aligns the RX buffer's DMA datasize to be
multiple of 64. So a packet slightly bigger than mtu+14, say 1536,
can be received and cause skb_over_panic.
Sample dmesg:
[ 5325.237162] skbuff: skb_over_panic: text:ffffffffc043277a len:1536 put:1536 head:ff1100018b517000 data:ff1100018b517100 tail:0x700 end:0x6ea dev:<NULL>
[ 5325.243689] ------------[ cut here ]------------
[ 5325.245748] kernel BUG at net/core/skbuff.c:192!
[ 5325.247838] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
[ 5325.258374] RIP: 0010:skb_panic+0x4f/0x60
[ 5325.302941] Call Trace:
[ 5325.304389] <IRQ>
[ 5325.315794] ? skb_panic+0x4f/0x60
[ 5325.317457] ? asm_exc_invalid_op+0x1f/0x30
[ 5325.319490] ? skb_panic+0x4f/0x60
[ 5325.321161] skb_put+0x4e/0x50
[ 5325.322670] mana_poll+0x6fa/0xb50 [mana]
[ 5325.324578] __napi_poll+0x33/0x1e0
[ 5325.326328] net_rx_action+0x12e/0x280
As discussed internally, this alignment is not necessary. To fix
this bug, remove it from the code. So oversized packets will be
marked as CQE_RX_TRUNCATED by NIC, and dropped.
Cc: stable@vger.kernel.org
Fixes: 2fbbd712baf1 ("net: mana: Enable RX path to handle various MTU sizes")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Link: https://lore.kernel.org/r/1712087316-20886-1-git-send-email-haiyangz@microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
qdisc_tree_reduce_backlog() is called with the qdisc lock held,
not RTNL.
We must use qdisc_lookup_rcu() instead of qdisc_lookup()
syzbot reported:
WARNING: suspicious RCU usage
6.1.74-syzkaller #0 Not tainted
-----------------------------
net/sched/sch_api.c:305 suspicious rcu_dereference_protected() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
3 locks held by udevd/1142:
#0: ffffffff87c729a0 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:306 [inline]
#0: ffffffff87c729a0 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:747 [inline]
#0: ffffffff87c729a0 (rcu_read_lock){....}-{1:2}, at: net_tx_action+0x64a/0x970 net/core/dev.c:5282
#1: ffff888171861108 (&sch->q.lock){+.-.}-{2:2}, at: spin_lock include/linux/spinlock.h:350 [inline]
#1: ffff888171861108 (&sch->q.lock){+.-.}-{2:2}, at: net_tx_action+0x754/0x970 net/core/dev.c:5297
#2: ffffffff87c729a0 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:306 [inline]
#2: ffffffff87c729a0 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:747 [inline]
#2: ffffffff87c729a0 (rcu_read_lock){....}-{1:2}, at: qdisc_tree_reduce_backlog+0x84/0x580 net/sched/sch_api.c:792
stack backtrace:
CPU: 1 PID: 1142 Comm: udevd Not tainted 6.1.74-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/25/2024
Call Trace:
<TASK>
[<ffffffff85b85f14>] __dump_stack lib/dump_stack.c:88 [inline]
[<ffffffff85b85f14>] dump_stack_lvl+0x1b1/0x28f lib/dump_stack.c:106
[<ffffffff85b86007>] dump_stack+0x15/0x1e lib/dump_stack.c:113
[<ffffffff81802299>] lockdep_rcu_suspicious+0x1b9/0x260 kernel/locking/lockdep.c:6592
[<ffffffff84f0054c>] qdisc_lookup+0xac/0x6f0 net/sched/sch_api.c:305
[<ffffffff84f037c3>] qdisc_tree_reduce_backlog+0x243/0x580 net/sched/sch_api.c:811
[<ffffffff84f5b78c>] pfifo_tail_enqueue+0x32c/0x4b0 net/sched/sch_fifo.c:51
[<ffffffff84fbcf63>] qdisc_enqueue include/net/sch_generic.h:833 [inline]
[<ffffffff84fbcf63>] netem_dequeue+0xeb3/0x15d0 net/sched/sch_netem.c:723
[<ffffffff84eecab9>] dequeue_skb net/sched/sch_generic.c:292 [inline]
[<ffffffff84eecab9>] qdisc_restart net/sched/sch_generic.c:397 [inline]
[<ffffffff84eecab9>] __qdisc_run+0x249/0x1e60 net/sched/sch_generic.c:415
[<ffffffff84d7aa96>] qdisc_run+0xd6/0x260 include/net/pkt_sched.h:125
[<ffffffff84d85d29>] net_tx_action+0x7c9/0x970 net/core/dev.c:5313
[<ffffffff85e002bd>] __do_softirq+0x2bd/0x9bd kernel/softirq.c:616
[<ffffffff81568bca>] invoke_softirq kernel/softirq.c:447 [inline]
[<ffffffff81568bca>] __irq_exit_rcu+0xca/0x230 kernel/softirq.c:700
[<ffffffff81568ae9>] irq_exit_rcu+0x9/0x20 kernel/softirq.c:712
[<ffffffff85b89f52>] sysvec_apic_timer_interrupt+0x42/0x90 arch/x86/kernel/apic/apic.c:1107
[<ffffffff85c00ccb>] asm_sysvec_apic_timer_interrupt+0x1b/0x20 arch/x86/include/asm/idtentry.h:656
Fixes: d636fc5dd692 ("net: sched: add rcu annotations around qdisc->qdisc_sleeping")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/20240402134133.2352776-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are 2 issues with the blamed commit.
1. When the phy is initialized, it would enable the disabled of UDPv4
checksums. The UDPv6 checksum is already enabled by default. So when
1-step is configured then it would clear these flags.
2. After the 1-step is configured, then if 2-step is configured then the
1-step would be still configured because it is not clearing the flag.
So the sync frames will still have origin timestamps set.
Fix this by reading first the value of the register and then
just change bit 12 as this one determines if the timestamp needs to
be inserted in the frame, without changing any other bits.
Fixes: ece19502834d ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Divya Koppera <divya.koppera@microchip.com>
Link: https://lore.kernel.org/r/20240402071634.2483524-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver should ensure that same priority is not mapped to multiple
rx queues. From DesignWare Cores Ethernet Quality-of-Service
Databook, section 17.1.29 MAC_RxQ_Ctrl2:
"[...]The software must ensure that the content of this field is
mutually exclusive to the PSRQ fields for other queues, that is,
the same priority is not mapped to multiple Rx queues[...]"
Previously rx_queue_priority() function was:
- clearing all priorities from a queue
- adding new priorities to that queue
After this patch it will:
- first assign new priorities to a queue
- then remove those priorities from all other queues
- keep other priorities previously assigned to that queue
Fixes: a8f5102af2a7 ("net: stmmac: TX and RX queue priority configuration")
Fixes: 2142754f8b9c ("net: stmmac: Add MAC related callbacks for XGMAC2")
Signed-off-by: Piotr Wejman <piotrwejman90@gmail.com>
Link: https://lore.kernel.org/r/20240401192239.33942-1-piotrwejman90@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
txgbe clkdev shortened clk_name, so i2c_dev info_name
also need to shorten. Otherwise, i2c_dev cannot initialize
clock.
Fixes: e30cef001da2 ("net: txgbe: fix clk_name exceed MAX_DEV_ID limits")
Signed-off-by: Duanqiang Wen <duanqiangwen@net-swift.com>
Link: https://lore.kernel.org/r/20240402021843.126192-1-duanqiangwen@net-swift.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
John Ernberg says:
====================
net: fec: Fix to suspend / resume with mac_managed_pm
Since the introduction of mac_managed_pm in the FEC driver there were some
discrepancies regarding power management of the PHY.
This failed on our board that has a permanently powered Microchip LAN8700R
attached to the FEC. Although the root cause of the failure can be traced
back to f166f890c8f0 ("net: ethernet: fec: Replace interrupt driven MDIO
with polled IO") and probably even before that, we only started noticing
the problem going from 5.10 to 6.1.
Since 557d5dc83f68 ("net: fec: use mac-managed PHY PM") is actually a fix
to most of the power management sequencing problems that came with power
managing the MDIO bus which for the FEC meant adding a race with FEC
resume (and phy_start() if netif was running) and PHY resume.
That it worked before for us was probably just luck...
Thanks to Wei's response to my report at [1] I was able to pick up his
patch and start honing in on the remaining missing details.
[1]: https://lore.kernel.org/netdev/1f45bdbe-eab1-4e59-8f24-add177590d27@actia.se/
v3: https://lore.kernel.org/netdev/20240306133734.4144808-1-john.ernberg@actia.se/
v2: https://lore.kernel.org/netdev/20240229105256.2903095-1-john.ernberg@actia.se/
v1: https://lore.kernel.org/netdev/20240212105010.2258421-1-john.ernberg@actia.se/
====================
Link: https://lore.kernel.org/r/20240328155909.59613-1-john.ernberg@actia.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Setting mac_managed_pm during interface up is too late.
In situations where the link is not brought up yet and the system suspends
the regular PHY power management will run. Since the FEC ETHEREN control
bit is cleared (automatically) on suspend the controller is off in resume.
When the regular PHY power management resume path runs in this context it
will write to the MII_DATA register but nothing will be transmitted on the
MDIO bus.
This can be observed by the following log:
fec 5b040000.ethernet eth0: MDIO read timeout
Microchip LAN87xx T1 5b040000.ethernet-1:04: PM: dpm_run_callback(): mdio_bus_phy_resume+0x0/0xc8 returns -110
Microchip LAN87xx T1 5b040000.ethernet-1:04: PM: failed to resume: error -110
The data written will however remain in the MII_DATA register.
When the link later is set to administrative up it will trigger a call to
fec_restart() which will restore the MII_SPEED register. This triggers the
quirk explained in f166f890c8f0 ("net: ethernet: fec: Replace interrupt
driven MDIO with polled IO") causing an extra MII_EVENT.
This extra event desynchronizes all the MDIO register reads, causing them
to complete too early. Leading all reads to read as 0 because
fec_enet_mdio_wait() returns too early.
When a Microchip LAN8700R PHY is connected to the FEC, the 0 reads causes
the PHY to be initialized incorrectly and the PHY will not transmit any
ethernet signal in this state. It cannot be brought out of this state
without a power cycle of the PHY.
Fixes: 557d5dc83f68 ("net: fec: use mac-managed PHY PM")
Closes: https://lore.kernel.org/netdev/1f45bdbe-eab1-4e59-8f24-add177590d27@actia.se/
Signed-off-by: Wei Fang <wei.fang@nxp.com>
[jernberg: commit message]
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Link: https://lore.kernel.org/r/20240328155909.59613-2-john.ernberg@actia.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This creates a subdirectory for each individual btree under the btrees/
debugfs directory.
Directory structure, before:
/sys/kernel/debug/bcachefs/$FS_ID/btrees/
├── alloc
├── alloc-bfloat-failed
├── alloc-formats
├── backpointers
├── backpointers-bfloat-failed
├── backpointers-formats
...
Directory structure, after:
/sys/kernel/debug/bcachefs/$FS_ID/btrees/
├── alloc
│ ├── bfloat-failed
│ ├── formats
│ └── keys
├── backpointers
│ ├── bfloat-failed
│ ├── formats
│ └── keys
...
Signed-off-by: Thomas Bertschinger <tahbertschinger@gmail.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
The RISC-V Vector specification states in "Appendix D: Calling
Convention for Vector State" [1] that "Executing a system call causes
all caller-saved vector registers (v0-v31, vl, vtype) and vstart to
become unspecified.". In the RISC-V kernel this is called "discarding
the vstate".
Returning from a signal handler via the rt_sigreturn() syscall, vector
discard is also performed. However, this is not an issue since the
vector state should be restored from the sigcontext, and therefore not
care about the vector discard.
The "live state" is the actual vector register in the running context,
and the "vstate" is the vector state of the task. A dirty live state,
means that the vstate and live state are not in synch.
When vectorized user_from_copy() was introduced, an bug sneaked in at
the restoration code, related to the discard of the live state.
An example when this go wrong:
1. A userland application is executing vector code
2. The application receives a signal, and the signal handler is
entered.
3. The application returns from the signal handler, using the
rt_sigreturn() syscall.
4. The live vector state is discarded upon entering the
rt_sigreturn(), and the live state is marked as "dirty", indicating
that the live state need to be synchronized with the current
vstate.
5. rt_sigreturn() restores the vstate, except the Vector registers,
from the sigcontext
6. rt_sigreturn() restores the Vector registers, from the sigcontext,
and now the vectorized user_from_copy() is used. The dirty live
state from the discard is saved to the vstate, making the vstate
corrupt.
7. rt_sigreturn() returns to the application, which crashes due to
corrupted vstate.
Note that the vectorized user_from_copy() is invoked depending on the
value of CONFIG_RISCV_ISA_V_UCOPY_THRESHOLD. Default is 768, which
means that vlen has to be larger than 128b for this bug to trigger.
The fix is simply to mark the live state as non-dirty/clean prior
performing the vstate restore.
Link: https://github.com/riscv/riscv-isa-manual/releases/download/riscv-isa-release-8abdb41-2024-03-26/unpriv-isa-asciidoc.pdf # [1]
Reported-by: Charlie Jenkins <charlie@rivosinc.com>
Reported-by: Vineet Gupta <vgupta@kernel.org>
Fixes: c2a658d41924 ("riscv: lib: vectorize copy_to_user/copy_from_user")
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Reviewed-by: Andy Chiu <andy.chiu@sifive.com>
Tested-by: Vineet Gupta <vineetg@rivosinc.com>
Link: https://lore.kernel.org/r/20240403072638.567446-1-bjorn@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The function using this is hidden in an #ifdef, so the variable
needs the same one for a clean W=1 build:
drivers/i2c/busses/i2c-pxa.c:327:26: error: 'icr_bits' defined but not used [-Werror=unused-const-variable=]
Fixes: d6a7b5f84b5c ("[ARM] 4827/1: fix two warnings in drivers/i2c/busses/i2c-pxa.c")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
The kstack_offset variable was really only ever using the low bits for
kernel stack offset entropy. Add a ror32() to increase bit diffusion.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 39218ff4c625 ("stack: Optionally randomize kernel stack offset each syscall")
Link: https://lore.kernel.org/r/20240309202445.work.165-kees@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
This is one of the drivers with an unused variable that is marked 'const'.
Adding a __used annotation here avoids the warning and lets us enable
the option by default:
lib/test_ubsan.c:137:28: error: unused variable 'skip_ubsan_array' [-Werror,-Wunused-const-variable]
Fixes: 4a26f49b7b3d ("ubsan: expand tests and reporting")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240403080702.3509288-3-arnd@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
The .head.text section carries the startup code that runs with the MMU
off or with a translation of memory that deviates from the ordinary one.
So avoid instrumentation with the stackleak plugin, which already avoids
.init.text and .noinstr.text entirely.
Fixes: 48204aba801f1b51 ("x86/sme: Move early SME kernel encryption handling into .head.text")
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202403221630.2692c998-oliver.sang@intel.com
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240328064256.2358634-2-ardb+git@google.com
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
Since mbox_cmd.size_out is overwritten with the actual output size in
the function below, it needs to be initialized every time.
cxl_internal_send_cmd -> __cxl_pci_mbox_send_cmd
Problem scenario:
1) The size_out variable is initially set to the size of the mailbox.
2) Read an event.
- size_out is set to 160 bytes(header 32B + one event 128B).
- Two event are created while reading.
3) Read the new *two* events.
- size_out is still set to 160 bytes.
- Although the value of out_len is 288 bytes, only 160 bytes are
copied from the mailbox register to the local variable.
- record_count is set to 2.
- Accessing records[1] will result in reading incorrect data.
Fixes: 6ebe28f9ec72 ("cxl/mem: Read, trace, and clear events on driver load")
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Kwangjin Ko <kwangjin.ko@sk.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
|
|
In the very rare case where a packet type is unknown to the driver,
idpf_rx_process_skb_fields would return early without calling
eth_type_trans to set the skb protocol / the network layer handler.
This is especially problematic if tcpdump is running when such a
packet is received, i.e. it would cause a kernel panic.
Instead, call eth_type_trans for every single packet, even when
the packet type is unknown.
Fixes: 3a8845af66ed ("idpf: add RX splitq napi poll support")
Reported-by: Balazs Nemeth <bnemeth@redhat.com>
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Salvatore Daniele <sdaniele@redhat.com>
Signed-off-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Both the vdso rework and the CONFIG_PAGE_SHIFT changes were merged during
the v6.9 merge window, so it is now possible to use CONFIG_PAGE_SHIFT
instead of including asm/page.h in the vdso.
This avoids the workaround for arm64 - commit 8b3843ae3634 ("vdso/datapage:
Quick fix - use asm/page-def.h for ARM64") and addresses a build warning
for powerpc64:
In file included from <built-in>:4:
In file included from /home/arnd/arm-soc/arm-soc/lib/vdso/gettimeofday.c:5:
In file included from ../include/vdso/datapage.h:25:
arch/powerpc/include/asm/page.h:230:9: error: result of comparison of constant 13835058055282163712 with expression of type 'unsigned long' is always true [-Werror,-Wtautological-constant-out-of-range-compare]
230 | return __pa(kaddr) >> PAGE_SHIFT;
| ^~~~~~~~~~~
arch/powerpc/include/asm/page.h:217:37: note: expanded from macro '__pa'
217 | VIRTUAL_WARN_ON((unsigned long)(x) < PAGE_OFFSET); \
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~
arch/powerpc/include/asm/page.h:202:73: note: expanded from macro 'VIRTUAL_WARN_ON'
202 | #define VIRTUAL_WARN_ON(x) WARN_ON(IS_ENABLED(CONFIG_DEBUG_VIRTUAL) && (x))
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~
arch/powerpc/include/asm/bug.h:88:25: note: expanded from macro 'WARN_ON'
88 | int __ret_warn_on = !!(x); \
| ^
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Link: https://lore.kernel.org/r/20240320180228.136371-1-arnd@kernel.org
|
|
Skip sessions that are being teared down (status == SES_EXITING) to
avoid UAF.
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Skip sessions that are being teared down (status == SES_EXITING) to
avoid UAF.
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Skip sessions that are being teared down (status == SES_EXITING) to
avoid UAF.
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Skip sessions that are being teared down (status == SES_EXITING) to
avoid UAF.
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Skip sessions that are being teared down (status == SES_EXITING) to
avoid UAF.
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Skip sessions that are being teared down (status == SES_EXITING) to
avoid UAF.
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Skip sessions that are being teared down (status == SES_EXITING) to
avoid UAF.
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Skip sessions that are being teared down (status == SES_EXITING) to
avoid UAF.
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Skip sessions that are being teared down (status == SES_EXITING) to
avoid UAF.
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
In the current implementation, CIFS close sends a close to the
server and does not check for the success of the server close.
This patch adds functionality to check for server close return
status and retries in case of an EBUSY or EAGAIN error.
This can help avoid handle leaks
Cc: stable@vger.kernel.org
Signed-off-by: Ritvik Budhiraja <rbudhiraja@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Starting with commit 7b937cc243e5 ("of: Create of_root if no dtb provided
by firmware"), attempts to boot nios2 images with an external devicetree
blob result in a crash.
Kernel panic - not syncing: early_init_dt_alloc_memory_arch:
Failed to allocate 72 bytes align=0x40
For nios2, a built-in devicetree blob always overrides devicetree blobs
provided by ROMMON/BIOS. This includes the new dummy devicetree blob.
Result is that the dummy devicetree blob is used even if an external
devicetree blob is provided. Since the dummy devicetree blob does not
include any memory information, memory allocations fail, resulting in
the crash.
To fix the problem, only use the built-in devicetree blob if
CONFIG_NIOS2_DTB_SOURCE_BOOL is enabled.
Fixes: 7b937cc243e5 ("of: Create of_root if no dtb provided by firmware")
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240322065419.162416-1-linux@roeck-us.net
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
If an inode is missing, but corresponding extents and dirent still
exist, it's well worth recreating it - this does so.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
We can now recreate missing subvolumes from dirents and/or inodes.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
In backpointer repair, if we get a missing backpointer - but there's
already a backpointer that points to an existing extent - we've got
multiple extents that point to the same space and need to decide which
to keep.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
When the snapshots btree is going, we'll have to delete huge amounts of
data - unless we can reconstruct it by looking at the keys that refer to
it.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
We need this to know when we should attempt to reconstruct the snapshots
btree
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
With the new btree node scan code, we can now recover from corrupt btree
roots - simply create a new fake root at depth 1, and then insert all
the leaves we found.
If the root wasn't corrupt but there's corruption elsewhere in the
btree, we can fill in holes as needed with the newest version of a given
node(s) from the scan; we also check if a given btree node is older than
what we found from the scan.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
If a btree root or interior btree node goes bad, we're going to lose a
lot of data, unless we can recover the nodes that it pointed to by
scanning.
Fortunately btree node headers are fully self describing, and
additionally the magic number is xored with the filesytem UUID, so we
can do so safely.
This implements the scanning - next patch will rework topology repair to
make use of the found nodes.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
When a btree root is unreadable, we might still have keys fro the
journal to walk and mark.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
Pull out eytzinger.c and kill eytzinger_cmp_fn. We now provide
eytzinger0_sort and eytzinger0_sort_r, which use the standard cmp_func_t
and cmp_r_func_t callbacks.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
