| Age | Commit message (Collapse) | Author |
|---|
|
|
|
It is necessary to clear MC13892_SWITCHERS0_SWxHI bit when set voltage to the
voltage range from 1100000 to 1375000. Leaving MC13892_SWITCHERS0_SWxHI bit
untouched may result in wrong voltage setting.
For example, currently switch voltage from 1400000 to 1300000 will set the
voltage to 1800000 because the HI bit is still set.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
|
|
It's safe to call regulator_unregister() with NULL, thus remove the NULL test
before regulator_unregister() calls.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
|
|
Patch adds device tree probe support for mc13783-regulator driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
|
|
This patch adds a warning about incorrect regulators instead of
printing the names of non-information message about the wrong amount.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
|
|
Ensure max77686->opmode always has correct status.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
|
|
* pm-cpufreq: (57 commits)
cpufreq: MAINTAINERS: Add co-maintainer
cpufreq: pxa2xx: initialize variables
ARM: S5pv210: compiling issue, ARM_S5PV210_CPUFREQ needs CONFIG_CPU_FREQ_TABLE=y
cpufreq: cpu0: Put cpu parent node after using it
cpufreq: ARM big LITTLE: Adapt to latest cpufreq updates
cpufreq: ARM big LITTLE: put DT nodes after using them
cpufreq: Don't call __cpufreq_governor() for drivers without target()
cpufreq: exynos5440: Protect OPP search calls with RCU lock
cpufreq: dbx500: Round to closest available freq
cpufreq: Call __cpufreq_governor() with correct policy->cpus mask
cpufreq / intel_pstate: Optimize intel_pstate_set_policy
cpufreq: OMAP: instantiate omap-cpufreq as a platform_driver
arm: exynos: Enable OPP library support for exynos5440
cpufreq: exynos: Remove error return even if no soc is found
cpufreq: exynos: Add cpufreq driver for exynos5440
cpufreq: AMD "frequency sensitivity feedback" powersave bias for ondemand governor
cpufreq: ondemand: allow custom powersave_bias_target handler to be registered
cpufreq: convert cpufreq_driver to using RCU
cpufreq: powerpc/platforms/cell: move cpufreq driver to drivers/cpufreq
cpufreq: sparc: move cpufreq driver to drivers/cpufreq
...
Conflicts:
MAINTAINERS (with commit a8e39c3 from pm-cpuidle)
drivers/cpufreq/cpufreq_governor.h (with commit beb0ff3)
|
|
* pm-cpuidle: (51 commits)
cpuidle: add maintainer entry
ARM: s3c64xx: cpuidle: use init/exit common routine
SH: cpuidle: use init/exit common routine
cpuidle: fix comment format
ARM: imx: cpuidle: use init/exit common routine
ARM: davinci: cpuidle: use init/exit common routine
ARM: kirkwood: cpuidle: use init/exit common routine
ARM: calxeda: cpuidle: use init/exit common routine
ARM: tegra: cpuidle: use init/exit common routine for tegra3
ARM: tegra: cpuidle: use init/exit common routine for tegra2
ARM: OMAP4: cpuidle: use init/exit common routine
ARM: shmobile: cpuidle: use init/exit common routine
ARM: tegra: cpuidle: use init/exit common routine
ARM: OMAP3: cpuidle: use init/exit common routine
ARM: at91: cpuidle: use init/exit common routine
ARM: ux500: cpuidle: use init/exit common routine
cpuidle: make a single register function for all
ARM: ux500: cpuidle: replace for_each_online_cpu by for_each_possible_cpu
cpuidle: remove en_core_tk_irqen flag
ARM: OMAP3: remove cpuidle_wrap_enter
...
|
|
* pnp:
pnp: use %*phC to dump small buffers
isapnp: remove debug leftovers
|
|
* pm-assorted:
PM / OPP: add documentation to RCU head in struct opp
PM / sleep: invalidate TEST_CPUS and TEST_CORE support for freeze state
PM / sleep: add TEST_PLATFORM support for freeze state
|
|
* pm-runtime:
PM / Runtime: Improve prepare handling at system suspend for genpd
PM / Runtime: Asyncronous idle|suspend parent devices at removal
PM / Runtime: Asyncronous idle|suspend devices at system resume
|
|
* acpi-assorted: (21 commits)
ACPI / thermal: do not always return THERMAL_TREND_RAISING for active trip points
ACPI: video: correct acpi_video_bus_add error processing
ACPI: Fix wrong parameter passed to memblock_reserve
acpi: video: enhance the quirk detect logic of _BQC
ACPI: update comments for acpi_event_status
ACPI: remove "config ACPI_DEBUG_FUNC_TRACE"
PCI / ACPI: Don't query OSC support with all possible controls
ACPI / processor_thermal: avoid null pointer deference error
ACPI / fan: avoid null pointer deference error
ACPI / video: Fix applying indexed initial brightness value.
ACPI / video: Make logic a little easier to understand.
ACPI / video: Fix brightness control initialization for some laptops.
ACPI: Use resource_size() in osl.c
ACPI / acpi_pad: Used PTR_RET
ACPI: suppress compiler warning in container.c
ACPI: suppress compiler warning in battery.c
ACPI: suppress compiler warnings in processor_throttling.c
ACPI: suppress compiler warnings in button.c
ACPI: replace kmalloc+memcpy with kmemdup
ACPI: Remove acpi_pci_bind_root() definition
...
|
|
* acpi-pm:
ACPI / PM: Expose lists of device wakeup power resources to user space
ACPI / PM: Fix potential problem in acpi_device_get_power()
|
|
* acpica: (33 commits)
ACPICA: Update version to 20130328
ACPICA: Add a lock to the internal object reference count mechanism
ACPICA: Fix a format string for 64-bit generation
ACPICA: Remove FORCE_DELETE option for global reference count mechanism
ACPICA: Improve error message for Index() operator
ACPICA: FADT: Remove extraneous warning for very large GPE registers
ACPICA: Fix a typo in a function header, no functional change
ACPICA: Fix a typo in an error message
ACPICA: Fix for some comments/headers
ACPICA: _OSI Support: handle any errors from acpi_os_acquire_mutex()
ACPICA: Predefine names: Add allowed argument types to master info table
ACPI: Set length even for TYPE_END_TAG acpi resource
ACPICA: Update version to 20130214
ACPICA: Object repair: Allow 0-length packages for variable-length packages
ACPICA: Disassembler: Add warnings for unresolved control methods
ACPICA: Return object repair: Add resource template repairs
ACPICA: Return object repair: Add string-to-unicode conversion
ACPICA: Split object conversion functions to a new file
ACPICA: Add mechanism for early object repairs on a per-name basis
ACPICA: Remove trailing comma in enum declarations
...
|
|
* acpi-lpss:
ACPI / LPSS: make code less confusing for reader
ACPI / LPSS: Add support for exposing LTR registers to user space
ACPI / scan: Add special handler for Intel Lynxpoint LPSS devices
|
|
* acpi-hotplug:
ACPI / memhotplug: Remove info->failed bit
ACPI / memhotplug: set info->enabled for memory present at boot time
ACPI: Verify device status after eject
acpi: remove reference to ACPI_HOTPLUG_IO
ACPI: Update _OST handling for notify
ACPI: Update PNPID match handling for notify
ACPI: Update PNPID set/free interfaces
ACPI: Remove acpi_device dependency in acpi_device_set_id()
ACPI / hotplug: Make acpi_hotplug_profile_ktype static
ACPI / scan: Make memory hotplug driver use struct acpi_scan_handler
ACPI / container: Use hotplug profile user space interface
ACPI / hotplug: Introduce user space interface for hotplug profiles
ACPI / scan: Introduce acpi_scan_handler_matching()
ACPI / container: Use common hotplug code
ACPI / scan: Introduce common code for ACPI-based device hotplug
ACPI / scan: Introduce acpi_scan_match_handler()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fix from Olof Johansson:
"A late-arriving fix for musb on OMAP4, resolving an issue where the
musb IP won't be clocked and thus not functional. Small in scope,
most of the lines changed is a longish comment."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP4: hwmod data: make 'ocp2scp_usb_phy_phy_48m" as the main clock
|
|
I think we could just move the full vm_iomap_memory() function into
util.h or similar, but I didn't get any reply from anybody actually
using nommu even to this trivial patch, so I'm not going to touch it any
more than required.
Here's the fairly minimal stub to make the nommu case at least
potentially work. It doesn't seem like anybody cares, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It has been reported that there is a new version (different USB rev)
of the Logitech DFGT in the 'wild'.
This patch allows the kernel to recognise this wheel and send it the
command to enter native mode.
Reported-by: "Denis Jovic" <djovic78@gmail.com>
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fix from Ingo Molnar:
"This fix adds missing RCU read protection"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
events: Protect access via task_subsys_state_check()
|
|
rebuild_sched_domains() might pass doms with offlined cpu to
partition_sched_domains(), which results in an oops:
general protection fault: 0000 [#1] SMP
...
RIP: 0010:[<ffffffff81077a1e>] [<ffffffff81077a1e>] get_group+0x6e/0x90
...
Call Trace:
[<ffffffff8107f07c>] build_sched_domains+0x70c/0xcb0
[<ffffffff8107f2a7>] ? build_sched_domains+0x937/0xcb0
[<ffffffff81173f64>] ? kfree+0xe4/0x1b0
[<ffffffff8107f6e0>] ? partition_sched_domains+0xc0/0x470
[<ffffffff8107f905>] partition_sched_domains+0x2e5/0x470
[<ffffffff8107f6e0>] ? partition_sched_domains+0xc0/0x470
[<ffffffff810c9007>] ? generate_sched_domains+0xc7/0x530
[<ffffffff810c94a8>] rebuild_sched_domains_locked+0x38/0x70
[<ffffffff810cb4a4>] cpuset_write_resmask+0x1a4/0x500
[<ffffffff810c8700>] ? cpuset_mount+0xe0/0xe0
[<ffffffff810c7f50>] ? cpuset_read_u64+0x100/0x100
[<ffffffff810be890>] ? cgroup_iter_next+0x90/0x90
[<ffffffff810cb300>] ? cpuset_css_offline+0x70/0x70
[<ffffffff810c1a73>] cgroup_file_write+0x133/0x2e0
[<ffffffff8118995b>] vfs_write+0xcb/0x130
[<ffffffff8118a174>] sys_write+0x64/0xa0
Reported-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
In cpuset_hotplug_workfn(), partition_sched_domains() is called without
hotplug lock held, which is actually needed (stated in the function
header of partition_sched_domains()).
This patch tries to use rebuild_sched_domains() to solve the above
issue, and makes the code looks a little simpler.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
This series contains updates to e1000e, igb and ixgbe.
There are 2 patches in this series which could be applied to net,
but since Linus is so very close to releasing 3.9, I do not think
it prudent to try and push these into net at this time. I have CC'd
stable on these patches so that they can queue them up as soon as
3.9 gets released.
The 2 patches are:
e1000e: fix numeric overflow in phc settime method
ixgbe: fix EICR write in ixgbe_msix_other
Richard provides a fix for e1000e by using a helper function from time.h
to resolve a unintended overflow in the PTP settime function.
Bruce provides a fix to wait for NAPI to be done with the current context
after disabling interrupts and then disable NAPI when the interface
is going down. This fixes a possible "unable to handle kernel paging
request" panic in net-next.
Andi Kleen provides a patch for igb to use mdelay instead of udelay
when we needed 100000us.
Jacob provides a fix for ixgbe to simply mask the lower 16bits off so that
ixgbe_msix_other does not write them in the EICR, which causes them to
remain high and be properly handled by the clean_rings interrupt routine
as normal.
Emil cleans up the logic in ixgbe_setup_loopback_test() to only access
registers applicable to the MAC type. In addition, removes majority
of the AUTOC register reads by using a cached value instead to avoid
writing corrupted values to AUTOC due to bad FW. Emil also add support
for disabling link during boot time. Lastly, he provides a patch which
adds the MAC type to the version in ethtool_regs which will make it
easier to check the MAC type when dumping registers with ethtool.
There is a separate ethtool tool patch which is dependent upon Emil's
last patch of the series to add the MAC type to the version in
ethtool_regs, which will be sent separately.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Or Gerlitz says:
====================
This series adds support for the SRIOV ndo_set_vf callbacks to the mlx4 driver.
Series done against the net-next tree as of commit 37fe0660981d7a "net:
fix address check in rtnl_fdb_del"
We have successfully tested the series on net-next, except for getting
the VF link info issue I have reported earlier today on netdev, we
see the problem for both ixgbe and mlx4 VFs. Just to make sure get
VF config is working OK with patch #6 - we have run it over 3.8.8 too.
We added to the V1 series two patches that disable HW timestamping
when running over a VF, as this isn't supported yet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support getting VF config.
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ndo_set_vf_spoofchk support
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to ndo_set_vf_vlan in the driver. Once this call is used the vport
is considered to be in VST mode. In this mode, the PPF driver configures
Ethernet QPs created by this VF to use this vlan id and priority. Currently
RoCE isn't supported on that mode.
The special values of VID=4095 or VID=0,UP=0 are considered as VGT.
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ndo_set_vf_mac support which allows to set the MAC address
for mlx4 VF Ethernet NICs from the host.
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add struct mlx4_vport_state where all the parameters related
to management of VFs port (virtual ports of the NIC eswitch) are kept.
The driver keeps an administrative and operational copy of the settings.
The current administrative copy becomes operational on the event of probing
a VF either on a VM or on the host.
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add reference counting to the driver MAC registeration code. This would
be needed for cases where a mac is registered from more than once, e.g
when both the host and the VM driver register the same mac, the host
for mac spoof protection purposes and the VM for its regular needs.
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Should not run HW clock overflow check if HW clock is not supported. Also, since
this watchdog is the only customer of service_task, no need to start it in that case.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Disable timestamp capability on virtual functions.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'attrbuf' is malloced in genl_family_rcv_msg() when family->maxattr &&
family->parallel_ops, thus should be freed before leaving from the error
handling cases, otherwise it will cause memory leak.
Introduced by commit def3117493eafd9dfa1f809d861e0031b2cc8a07
(genl: Allow concurrent genl callbacks.)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
freeze.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
One MUSB regression fix that I forgot to send earlier. Without
this MUSB no longer works on omap4 based devices.
* tag 'omap-for-v3.9-rc6/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: hwmod data: make 'ocp2scp_usb_phy_phy_48m" as the main clock
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The Nomadik clocksource driver has had a bad define making it
impossible to use it for sched_clock() for a while. Fix this
and also enable it for the Nomadik.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The UART1 is on the fast AHB bridge, not on the slow bus.
Cc: stable@vger.kernel.org
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Since the NFC subsystem gained RFKILL support, it needs to be able
to build properly with whatever option for RFKILL has been selected.
on i386:
net/built-in.o: In function `nfc_unregister_device':
(.text+0x6a36d): undefined reference to `rfkill_unregister'
net/built-in.o: In function `nfc_unregister_device':
(.text+0x6a378): undefined reference to `rfkill_destroy'
net/built-in.o: In function `nfc_register_device':
(.text+0x6a493): undefined reference to `rfkill_alloc'
net/built-in.o: In function `nfc_register_device':
(.text+0x6a4a4): undefined reference to `rfkill_register'
net/built-in.o: In function `nfc_register_device':
(.text+0x6a4b3): undefined reference to `rfkill_destroy'
net/built-in.o: In function `nfc_dev_up':
(.text+0x6a8e8): undefined reference to `rfkill_blocked'
when CONFIG_RFKILL=m but NFC is builtin.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add Viresh as a co-maintainer of cpufreq framework.
This would mostly be for cpufreq core and ARM drivers but not
restricted to them.
Also add a pointer to the git tree cpufreq patches are pulled into.
[rjw: Changelog]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tentatively-acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently cpuidle drivers are spread across different archs.
As a result, there are several different paths for cpuidle patch
submissions: cpuidle core changes go through linux-pm, ARM driver
changes go to the arm-soc or SoC-specific trees, sh changes go
through the sh arch tree, pseries changes go through the PowerPC tree
and finally intel changes go through the Len's tree while ACPI idle
changes go through linux-pm.
That makes it difficult to consolidate code and to propagate
modifications from the cpuidle core to the different drivers.
Hopefully, a movement has started to put the majority of cpuidle
drivers under drivers/cpuidle like cpuidle-calxeda.c and
cpuidle-kirkwood.c.
Add a maintainer entry for cpuidle to MAINTAINERS to clarify the
situation and to indicate to new cpuidle driver authors that those
drivers should not go into arch-specific directories.
The upstreaming process is unchanged: Rafael takes patches for
merging into his tree, but with an Acked-by: tag from the driver's
maintainer, so indicate in the drivers' headers who maintains them.
The arrangement will be the same as for cpufreq.
[rjw: Changelog]
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andrew Lunn <andrew@lunn.ch> #for kirkwood
Acked-by: Jason Cooper <jason@lakedaemon.net> #for kirkwood
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
I mistakenly removed the call to eventfd->poll() while I was actually
intending to remove the return value...
Calling evenfd->poll() will hook cgroup_event_wake() to the poll
waitqueue, which will be called to unregister eventfd when rmdir a
cgroup or close eventfd.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Try:
# mount -t cgroup xxx /cgroup
# mkdir /cgroup/sub && rmdir /cgroup/sub && umount /cgroup
And you might see this:
ida_remove called for id=1 which is not allocated.
It's because cgroup_kill_sb() is called to destroy root->cgroup_ida
and free cgrp->root before ida_simple_removed() is called. What's
worse is we're accessing cgrp->root while it has been freed.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
This just merges in the revert of multiplatform support. Not doing it by
cherry-pick since we need the same revert in the next/drivers branch.
* samsung/exynos-multiplatform:
Revert "ARM: exynos: enable multiplatform support"
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This reverts commit bd51de53e1be9896d815bbea30560262216d4616.
Turns out that multiplatform breaks some uses cases, such as when you
have an existing defconfig, since it adds the new EXYNOS_SINGLE config
option as a dependecy. As a result, nearly all exynos config options
will be disabled by default.
Reverting instead of rebasing since this branch is pulled in as a
dependency elsewhere.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Ensure to unregister all regulators before return error in probe().
The regulator register order depends on the regulator ID pass to
ab3100_regulator_register() function. Thus we need to scan ab3100_regulator_desc
and find the index of successfully registered regulators, or alternatively just
call ab3100_regulators_remove() to unregister all registered regulators.
Since current code uses a static ab3100_regulators table, explicitly set
reg->rdev = NULL after regulator_unregister() call to ensure calling
ab3100_regulators_remove() in the unwind path always work.
Also move ab3100_regulators_remove() to avoid forward declaration.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
All regulators have ascendant voltage list in this driver.
Use regulator_map_voltage_ascend for them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Two driver fixes.
One avoids reading any file at a system with a cx25821 board
(fortunately, this is not a common device). The other one prevents
reading after a buffer with ISDB-T devices based on mb86a20s."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] cx25821: do not expose broken video output streams
[media] mb86a20s: Fix estimate_rate setting
|
