| Age | Commit message (Collapse) | Author |
|---|
|
The canonical node name for touchscreens is "touchscreen",
so update the i.MX6UL "tsc" node accordingly.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Replace all "xnur-gpio" with "xnur-gpios" in the i.MX6UL(L) Touchscreen
node, since the -gpio suffix is deprecated. All known implementations of
this binding can handle -gpio and -gpios since day 1, so this should be
fully backwards compatible.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
fsl,anatop should only be added to the usbphy nodes.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
pinctrl node name must be either pinctrl or pinmux.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Per davicom,dm9000.yaml, the Ethernet node name should be 'ethernet'.
Change it to fix the following schema warning:
imx1-apf9328.dtb: eth@4,c00000: $nodename:0: 'eth@4,c00000' does not match '^ethernet(@.*)?$'
from schema $id: http://devicetree.org/schemas/net/davicom,dm9000.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Per at24.yaml, the node name should be 'eeprom'.
Change it accordingly to fix the following schema warning:
imx28-evk.dtb: at24@51: $nodename:0: 'at24@51' does not match '^eeprom@[0-9a-f]{1,2}$'
from schema $id: http://devicetree.org/schemas/eeprom/at24.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable USB3 HW LPM feature.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
|
|
Pull bcachefs fixes from Kent Overstreet:
"Some more mostly boring fixes, but some not
User reported ones:
- the BTREE_ITER_FILTER_SNAPSHOTS one fixes a really nasty
performance bug; user reported an untar initially taking two
seconds and then ~2 minutes
- kill a __GFP_NOFAIL in the buffered read path; this was a leftover
from the trickier fix to kill __GFP_NOFAIL in readahead, where we
can't return errors (and have to silently truncate the read
ourselves).
bcachefs can't use GFP_NOFAIL for folio state unlike iomap based
filesystems because our folio state is just barely too big, 2MB
hugepages cause us to exceed the 2 page threshhold for GFP_NOFAIL.
additionally, the flags argument was just buggy, we weren't
supplying GFP_KERNEL previously (!)"
* tag 'bcachefs-2024-02-25' of https://evilpiepirate.org/git/bcachefs:
bcachefs: fix bch2_save_backtrace()
bcachefs: Fix check_snapshot() memcpy
bcachefs: Fix bch2_journal_flush_device_pins()
bcachefs: fix iov_iter count underflow on sub-block dio read
bcachefs: Fix BTREE_ITER_FILTER_SNAPSHOTS on inodes btree
bcachefs: Kill __GFP_NOFAIL in buffered read path
bcachefs: fix backpointer_to_text() when dev does not exist
|
|
Missed a call in the previous fix.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
Pull two documentation build fixes from Jonathan Corbet:
- The XFS online fsck documentation uses incredibly deeply nested
subsection and list nesting; that broke the PDF docs build. Tweak a
parameter to tell LaTeX to allow the deeper nesting.
- Fix a 6.8 PDF-build regression
* tag 'docs-6.8-fixes3' of git://git.lwn.net/linux:
docs: translations: use attribute to store current language
docs: Instruct LaTeX to cope with deeper nesting
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 6.8-rc6 to resolve some reported
problems. These include:
- regression fixes with typec tpcm code as reported by many
- cdnsp and cdns3 driver fixes
- usb role setting code bugfixes
- build fix for uhci driver
- ncm gadget driver bugfix
- MAINTAINERS entry update
All of these have been in linux-next all week with no reported issues
and there is at least one fix in here that is in Thorsten's regression
list that is being tracked"
* tag 'usb-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: tpcm: Fix issues with power being removed during reset
MAINTAINERS: Drop myself as maintainer of TYPEC port controller drivers
usb: gadget: ncm: Avoid dropping datagrams of properly parsed NTBs
Revert "usb: typec: tcpm: reset counter when enter into unattached state after try role"
usb: gadget: omap_udc: fix USB gadget regression on Palm TE
usb: dwc3: gadget: Don't disconnect if not started
usb: cdns3: fix memory double free when handle zero packet
usb: cdns3: fixed memory use after free at cdns3_gadget_ep_disable()
usb: roles: don't get/set_role() when usb_role_switch is unregistered
usb: roles: fix NULL pointer issue when put module's reference
usb: cdnsp: fixed issue with incorrect detecting CDNSP family controllers
usb: cdnsp: blocked some cdns3 specific code
usb: uhci-grlib: Explicitly include linux/platform_device.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are three small serial/tty driver fixes for 6.8-rc6 that resolve
the following reported errors:
- riscv hvc console driver fix that was reported by many
- amba-pl011 serial driver fix for RS485 mode
- stm32 serial driver fix for RS485 mode
All of these have been in linux-next all week with no reported
problems"
* tag 'tty-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: amba-pl011: Fix DMA transmission in RS485 mode
serial: stm32: do not always set SER_RS485_RX_DURING_TX if RS485 is enabled
tty: hvc: Don't enable the RISC-V SBI console by default
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Make sure clearing CPU buffers using VERW happens at the latest
possible point in the return-to-userspace path, otherwise memory
accesses after the VERW execution could cause data to land in CPU
buffers again
* tag 'x86_urgent_for_v6.8_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
KVM/VMX: Move VERW closer to VMentry for MDS mitigation
KVM/VMX: Use BT+JNC, i.e. EFLAGS.CF to select VMRESUME vs. VMLAUNCH
x86/bugs: Use ALTERNATIVE() instead of mds_user_clear static key
x86/entry_32: Add VERW just before userspace transition
x86/entry_64: Add VERW just before userspace transition
x86/bugs: Add asm helpers for executing VERW
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Borislav Petkov:
- Make sure GICv4 always gets initialized to prevent a kexec-ed kernel
from silently failing to set it up
- Do not call bus_get_dev_root() for the mbigen irqchip as it always
returns NULL - use NULL directly
- Fix hardware interrupt number truncation when assigning MSI
interrupts
- Correct sending end-of-interrupt messages to disabled interrupts
lines on RISC-V PLIC
* tag 'irq_urgent_for_v6.8_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Do not assume vPE tables are preallocated
irqchip/mbigen: Don't use bus_get_dev_root() to find the parent
PCI/MSI: Prevent MSI hardware interrupt number truncation
irqchip/sifive-plic: Enable interrupt if needed before EOI
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull erofs fix from Gao Xiang:
- Fix page refcount leak when looking up specific inodes
introduced by metabuf reworking
* tag 'erofs-for-6.8-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: fix refcount on the metabuf used for inode lookup
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull RCU pathwalk fixes from Al Viro:
"We still have some races in filesystem methods when exposed to RCU
pathwalk. This series is a result of code audit (the second round of
it) and it should deal with most of that stuff.
Still pending: ntfs3 ->d_hash()/->d_compare() and ceph_d_revalidate().
Up to maintainers (a note for NTFS folks - when documentation says
that a method may not block, it *does* imply that blocking allocations
are to be avoided. Really)"
[ More explanations for people who aren't familiar with the vagaries of
RCU path walking: most of it is hidden from filesystems, but if a
filesystem actively participates in the low-level path walking it
needs to make sure the fields involved in that walk are RCU-safe.
That "actively participate in low-level path walking" includes things
like having its own ->d_hash()/->d_compare() routines, or by having
its own directory permission function that doesn't just use the common
helpers. Having a ->d_revalidate() function will also have this issue.
Note that instead of making everything RCU safe you can also choose to
abort the RCU pathwalk if your operation cannot be done safely under
RCU, but that obviously comes with a performance penalty. One common
pattern is to allow the simple cases under RCU, and abort only if you
need to do something more complicated.
So not everything needs to be RCU-safe, and things like the inode etc
that the VFS itself maintains obviously already are. But these fixes
tend to be about properly RCU-delaying things like ->s_fs_info that
are maintained by the filesystem and that got potentially released too
early. - Linus ]
* tag 'pull-fixes.pathwalk-rcu-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ext4_get_link(): fix breakage in RCU mode
cifs_get_link(): bail out in unsafe case
fuse: fix UAF in rcu pathwalks
procfs: make freeing proc_fs_info rcu-delayed
procfs: move dropping pde and pid from ->evict_inode() to ->free_inode()
nfs: fix UAF on pathwalk running into umount
nfs: make nfs_set_verifier() safe for use in RCU pathwalk
afs: fix __afs_break_callback() / afs_drop_open_mmap() race
hfsplus: switch to rcu-delayed unloading of nls and freeing ->s_fs_info
exfat: move freeing sbi, upcase table and dropping nls into rcu-delayed helper
affs: free affs_sb_info with kfree_rcu()
rcu pathwalk: prevent bogus hard errors from may_lookup()
fs/super.c: don't drop ->s_user_ns until we free struct super_block itself
|
|
Pull vfs fixes from Al Viro:
"A couple of fixes - revert of regression from this cycle and a fix for
erofs failure exit breakage (had been there since way back)"
* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
erofs: fix handling kern_mount() failure
Revert "get rid of DCACHE_GENOCIDE"
|
|
Add compatible value for i.MX6ULL based UNI-T UTi260B thermal camera.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Uni-Trend Technology is a manufacturer of measurement
and testing tools.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The hdmi@3d node's compatible string is "adi,adv7535" instead of
"adi,adv7533" or "adi,adv751*".
Fix the hdmi@3d node by means of:
* Use default register addresses for "cec", "edid" and "packet", because
there is no need to use a non-default address map.
* Add missing interrupt related properties.
* Drop "adi,input-*" properties which are only valid for adv751*.
* Add VEXT_3V3 fixed regulator.
* Add "*-supply" properties, since most are required.
* Fix label names - s/adv7533/adv7535/.
Fixes: 65344b9bed3a ("arm64: dts: imx8mp-evk: Add HDMI support")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Per nxp,dwmac-imx.yaml, phy-supply is not a valid property.
Remove it to fix the following dt-schema warning:
imx93-var-som-symphony.dtb: ethernet@428a0000: Unevaluated properties are not allowed ('phy-supply' was unexpected)
from schema $id: http://devicetree.org/schemas/net/nxp,dwmac-imx.yaml#
The reg_eqos_phy regulator is marked as 'regulator-always-on', so it is
safe to remove the phy-supply property.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Removes the pull-up resistor from the pad's settings to keep it
consistent for all boards. We have pull-ups in hardware on all boards so we
don't need to set the additional one from the iomux controller.
Signed-off-by: Dominik Haller <d.haller@phytec.de>
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
Signed-off-by: Yashwanth Varakala <y.varakala@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Reduce drive strength on eqos tx lines for signal quality improvements.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
Signed-off-by: Yashwanth Varakala <y.varakala@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Set Pull Resistors Enable bit to put signal into a defined state.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
Signed-off-by: Yashwanth Varakala <y.varakala@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The interrupt of the RTC is connected on the carrier board
phyBOARD-i.MX8MP-Pollux.
RTC trickle-charger devicetree property is dependent on the
phyboard-pollux design.
Signed-off-by: Yashwanth Varakala <y.varakala@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add spdif sound card support, configure the pinmux.
This sound card supports recording and playing sound
through spdif interface.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The GPIO expander is a interrupt-controller, so add the missing
#interrupt-cells property as well.
Fixes: 71363a485ad0c ("arm64: dts: freescale: add initial device tree for TQMa8Xx")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SPI NOR bus routing on this board cannot go above 50 MHz,
set the clock frequency to maximum of 40 MHz to be within a
safe margin. Remove the comment as well.
Fixes: 562d222f23f0 ("arm64: dts: imx8mp: Add support for Data Modul i.MX8M Plus eDM SBC")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
We identified that the PHYs actually do not work since commit 7da7b84fee58
("ARM: dts: imx6dl-yapp4: Move phy reset into switch node") as
a coincidence of several circumstances.
The reset signal is kept asserted by a pull-down resistor on the board
unless it is deasserted by GPIO from the SoC. This is to keep the switch
dead until it is configured properly by the kernel and user space.
Prior to the referenced commit the switch was reset by the FEC driver
and the reset GPIO was actively deasserted. The mdio-bus was scanned
and the attached switch and its PHYs were found and configured.
With the referenced commit the switch is reset by the qca8k driver.
Because of another bug in the qca8k driver, functionality of the reset
pin depends on its pre-kernel configuration. See commit c44fc98f0a8f
("net: dsa: qca8k: fix illegal usage of GPIO")
The problem did not appear until we removed support for the switch
and configuration of its reset pin from the bootloader.
To fix that, properly describe the internal mdio-bus configuration of
the qca8334 switch. The PHYs are internal to the switch and sit on its
internal mdio-bus.
Fixes: 7da7b84fee58 ("ARM: dts: imx6dl-yapp4: Move phy reset into switch node")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This change does not have any functional effect. The switch works just
fine without this patch as it has full access to all the addresses
on the bus. This is simply a clean-up to set the node name address
and reg address to the same value.
Fixes: 15b43e497ffd ("ARM: dts: imx6dl-yapp4: Use correct pseudo PHY address for the switch")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
imx8mn has only one USB interface. The platform supports using as USB host
(default), or switch to USB DR using this overlay.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
VBUS 5V is statically provided to both USB host and on-bard USB-hub.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
PCIe reference clock is provided by Renesas 9FGV0441. Reference this
instead of a fixed-clock.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
1) errors from ext4_getblk() should not be propagated to caller
unless we are really sure that we would've gotten the same error
in non-RCU pathwalk.
2) we leak buffer_heads if ext4_getblk() is successful, but bh is
not uptodate.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
->d_revalidate() bails out there, anyway. It's not enough
to prevent getting into ->get_link() in RCU mode, but that
could happen only in a very contrieved setup. Not worth
trying to do anything fancy here unless ->d_revalidate()
stops kicking out of RCU mode at least in some cases.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Acked-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
->permission(), ->get_link() and ->inode_get_acl() might dereference
->s_fs_info (and, in case of ->permission(), ->s_fs_info->fc->user_ns
as well) when called from rcu pathwalk.
Freeing ->s_fs_info->fc is rcu-delayed; we need to make freeing ->s_fs_info
and dropping ->user_ns rcu-delayed too.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
makes proc_pid_ns() safe from rcu pathwalk (put_pid_ns()
is still synchronous, but that's not a problem - it does
rcu-delay everything that needs to be)
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
that keeps both around until struct inode is freed, making access
to them safe from rcu-pathwalk
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
NFS ->d_revalidate(), ->permission() and ->get_link() need to access
some parts of nfs_server when called in RCU mode:
server->flags
server->caps
*(server->io_stats)
and, worst of all, call
server->nfs_client->rpc_ops->have_delegation
(the last one - as NFS_PROTO(inode)->have_delegation()). We really
don't want to RCU-delay the entire nfs_free_server() (it would have
to be done with schedule_work() from RCU callback, since it can't
be made to run from interrupt context), but actual freeing of
nfs_server and ->io_stats can be done via call_rcu() just fine.
nfs_client part is handled simply by making nfs_free_client() use
kfree_rcu().
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
nfs_set_verifier() relies upon dentry being pinned; if that's
the case, grabbing ->d_lock stabilizes ->d_parent and guarantees
that ->d_parent points to a positive dentry. For something
we'd run into in RCU mode that is *not* true - dentry might've
been through dentry_kill() just as we grabbed ->d_lock, with
its parent going through the same just as we get to into
nfs_set_verifier_locked(). It might get to detaching inode
(and zeroing ->d_inode) before nfs_set_verifier_locked() gets
to fetching that; we get an oops as the result.
That can happen in nfs{,4} ->d_revalidate(); the call chain in
question is nfs_set_verifier_locked() <- nfs_set_verifier() <-
nfs_lookup_revalidate_delegated() <- nfs{,4}_do_lookup_revalidate().
We have checked that the parent had been positive, but that's
done before we get to nfs_set_verifier() and it's possible for
memory pressure to pick our dentry as eviction candidate by that
time. If that happens, back-to-back attempts to kill dentry and
its parent are quite normal. Sure, in case of eviction we'll
fail the ->d_seq check in the caller, but we need to survive
until we return there...
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
In __afs_break_callback() we might check ->cb_nr_mmap and if it's non-zero
do queue_work(&vnode->cb_work). In afs_drop_open_mmap() we decrement
->cb_nr_mmap and do flush_work(&vnode->cb_work) if it reaches zero.
The trouble is, there's nothing to prevent __afs_break_callback() from
seeing ->cb_nr_mmap before the decrement and do queue_work() after both
the decrement and flush_work(). If that happens, we might be in trouble -
vnode might get freed before the queued work runs.
__afs_break_callback() is always done under ->cb_lock, so let's make
sure that ->cb_nr_mmap can change from non-zero to zero while holding
->cb_lock (the spinlock component of it - it's a seqlock and we don't
need to mess with the counter).
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
->d_hash() and ->d_compare() use those, so we need to delay freeing
them.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
That stuff can be accessed by ->d_hash()/->d_compare(); as it is, we have
a hard-to-hit UAF if rcu pathwalk manages to get into ->d_hash() on a filesystem
that is in process of getting shut down.
Besides, having nls and upcase table cleanup moved from ->put_super() towards
the place where sbi is freed makes for simpler failure exits.
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
one of the flags in it is used by ->d_hash()/->d_compare()
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
If lazy call of ->permission() returns a hard error, check that
try_to_unlazy() succeeds before returning it. That both makes
life easier for ->permission() instances and closes the race
in ENOTDIR handling - it is possible that positive d_can_lookup()
seen in link_path_walk() applies to the state *after* unlink() +
mkdir(), while nd->inode matches the state prior to that.
Normally seeing e.g. EACCES from permission check in rcu pathwalk
means that with some timings non-rcu pathwalk would've run into
the same; however, running into a non-executable regular file
in the middle of a pathname would not get to permission check -
it would fail with ENOTDIR instead.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Avoids fun races in RCU pathwalk... Same goes for freeing LSM shite
hanging off super_block's arse.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Since commit 8208181fe536 ("clk: imx: composite-8m:
Add imx8m_divider_determine_rate") the lcdif controller has
had the ability to set the disp_pixel_clk rate which propagates
up the tree and sets the video_pll rate automatically.
As such, there is no need to define it in the board file.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since commit 8208181fe536 ("clk: imx: composite-8m:
Add imx8m_divider_determine_rate") the lcdif controller has
had the ability to set the disp_pixel_clk rate which propagates
up the tree and sets the video_pll rate automatically.
By setting this value low, it will force the recalculation of
video_pll to the lowest rate needed by lcdif instead of
dividing a larger clock down to the desired clock speed. This
has the advantage of being able to lower the video_pll rate
from 594MHz to 148.5MHz when operating at 1080p. It can go even
lower when operating at lower resolutions and refresh rates.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The imx8mp-beacon SOM has an integrated PHY connected to
the EQOS ethernet controller which can support up to five
queues. Configure these queues in the same manor as done
on the imx8mp-evk.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
