| Age | Commit message (Collapse) | Author |
|---|
|
The official way to stop the display is to clear the display enable
(DEN) bit in the DSYSR register, but that operates at a group level and
affects the two channels in the group. To disable channels selectively,
the driver uses TV sync mode that stops display operation on the channel
and turns output signals into inputs.
While TV sync mode is available in all DU models currently supported,
the D3 and E3 DUs don't support it. We will thus need to find an
alternative way to turn channels off.
In the meantime, condition the switch to TV sync mode to the
availability of the feature, to avoid writing an invalid value to the
DSYSR register. When the feature is unavailable the display output will
turn blank as all planes are disabled when stopping the CRTC.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
|
|
DSYSR is a DU channel register that also contains group fields. It is
thus written to by both the group and CRTC code, using read-update-write
sequences. As the register isn't initialized explicitly at startup time,
this can lead to invalid or otherwise unexpected values being written to
some of the fields if they have been modified by the firmware or just
not reset properly.
To fix this we can write a fully known value to the DSYSR register when
turning a channel's functional clock on. However, the mix of group and
channel fields complicate this. A simpler solution is to cache the
register and initialize the cached value to the desired hardware
defaults.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
|
|
All Gen3 SoCs supported so far have a fixed association between DPAD0
and DU channels, which led to hardcoding that association when writing
the corresponding hardware register. The D3 and E3 will break that
mechanism as DPAD0 can be dynamically connected to either DU0 or DU1.
Make DPAD0 routing dynamic on Gen3. To ensure a valid hardware
configuration when the DU starts without the RGB output enabled, DPAD0
is associated at initialization time to the first DU channel that it can
be connected to. This makes no change on Gen2 as all Gen2 SoCs can
connected DPAD0 to DU0, which is the current implicit default value.
As the DPAD0 source is always 0 when a single source is possible on
Gen2, we can also simplify the Gen2 code in the same function to remove
a conditional check.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
|
|
On selected SoCs, the DU can use the clock output by the LVDS encoder
PLL as its input dot clock. This feature is optional, but on the D3 and
E3 SoC it is often the only way to obtain a precise dot clock frequency,
as the other available clocks (CPG-generated clock and external clock)
usually have fixed rates.
Add a DU model information field to describe which DU channels can use
the LVDS PLL output clock as their input clock, and configure clock
routing accordingly.
This feature is available on H2, M2-W, M2-N, D3 and E3 SoCs, with D3 and
E3 being the primary targets. It is left disabled in this commit, and
will be enabled per-SoC after careful testing.
At the hardware level, clock routing is configured at runtime in two
steps, first selecting an internal dot clock between the LVDS PLL clock
and the external DOTCLKIN clock, and then selecting between the internal
dot clock and the CPG-generated clock. The first part requires stopping
the whole DU group in order for the change to take effect, thus causing
flickering on the screen. For this reason we currently hardcode the
clock source to the LVDS PLL clock if available, and allow flicker-free
selection of the external DOTCLKIN clock or CPG-generated clock
otherwise. A more dynamic clock selection process can be implemented
later if the need arises.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
|
|
The rcar_du_crtc_get() function is always immediately followed by a call
to rcar_du_crtc_setup(). Call the later from the former to simplify the
code, and add a comment to explain how the get and put calls are
balanced.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
|
|
The LVDS encoders in the D3 and E3 SoCs differ significantly from those
in the other R-Car Gen3 family members:
- The LVDS PLL architecture is more complex and requires computing PLL
parameters manually.
- The PLL uses external clocks as inputs, which need to be retrieved
from DT.
- In addition to the different PLL setup, the startup sequence has
changed *again* (seems someone had trouble making his/her mind).
Supporting all this requires DT bindings extensions for external clocks,
brand new PLL setup code, and a few quirks to handle the differences in
the startup sequence.
The implementation doesn't support all hardware features yet, namely
- Using the LV[01] clocks generated by the CPG as PLL input.
- Providing the LVDS PLL clock to the DU for use with the RGB output.
Those features can be added later when the need will arise.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
|
|
The THC63LVD1024 is restricted to a pixel clock frequency in the range
of 8 to 135 MHz. Implement the bridge .mode_valid() operation
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
|
|
On the D3 and E3 SoCs, the LVDS encoder can derive its internal pixel
clock from an externally supplied clock, either through the EXTAL pin or
through one of the DU_DOTCLKINx pins. Add corresponding clocks to the DT
bindings.
To retain backward compatibility with DT that don't specify the
clock-names property, the functional clock must always be specified
first, and the clock-names property is optional when only the functional
clock is specified.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
|
|
Building a riscv kernel with CONFIG_FUNCTION_TRACER and
CONFIG_MODVERSIONS enabled results in these two warnings:
MODPOST vmlinux.o
WARNING: EXPORT symbol "return_to_handler" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "_mcount" [vmlinux] version generation failed, symbol will not be versioned.
When exporting symbols from an assembly file, the MODVERSIONS code
requires their prototypes to be defined in asm-prototypes.h (see
scripts/Makefile.build). Since both of these symbols have prototypes
defined in linux/ftrace.h, include this header from RISC-V's
asm-prototypes.h.
Reported-by: Karsten Merker <merker@debian.org>
Signed-off-by: James Cowgill <jcowgill@debian.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
With CONFIG_DMA_API_DEBUG enabled we get DMA unmapping warning in
various places of the mvneta driver, for example when putting down an
interface while traffic is passing through.
The issue is when using s/w buffer management, the Rx buffers are mapped
using dma_map_page but unmapped with dma_unmap_single. This patch fixes
this by using the right unmapping function.
Fixes: 562e2f467e71 ("net: mvneta: Improve the buffer allocation method for SWBM")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cong noted that we need the same checks introduced by commit 76c0ddd8c3a6
("ip6_tunnel: be careful when accessing the inner header")
even for ipv4 tunnels.
Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.")
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Summary:
This appears to be necessary and sufficient change to enable `MPLS` on
`ip6gre` tunnels (RFC4023).
This diff allows IP6GRE devices to be recognized by MPLS kernel module
and hence user can configure interface to accept packets with mpls
headers as well setup mpls routes on them.
Test Plan:
Test plan consists of multiple containers connected via GRE-V6 tunnel.
Then carrying out testing steps as below.
- Carry out necessary sysctl settings on all containers
```
sysctl -w net.mpls.platform_labels=65536
sysctl -w net.mpls.ip_ttl_propagate=1
sysctl -w net.mpls.conf.lo.input=1
```
- Establish IP6GRE tunnels
```
ip -6 tunnel add name if_1_2_1 mode ip6gre \
local 2401:db00:21:6048:feed:0::1 \
remote 2401:db00:21:6048:feed:0::2 key 1
ip link set dev if_1_2_1 up
sysctl -w net.mpls.conf.if_1_2_1.input=1
ip -4 addr add 169.254.0.2/31 dev if_1_2_1 scope link
ip -6 tunnel add name if_1_3_1 mode ip6gre \
local 2401:db00:21:6048:feed:0::1 \
remote 2401:db00:21:6048:feed:0::3 key 1
ip link set dev if_1_3_1 up
sysctl -w net.mpls.conf.if_1_3_1.input=1
ip -4 addr add 169.254.0.4/31 dev if_1_3_1 scope link
```
- Install MPLS encap rules on node-1 towards node-2
```
ip route add 192.168.0.11/32 nexthop encap mpls 32/64 \
via inet 169.254.0.3 dev if_1_2_1
```
- Install MPLS forwarding rules on node-2 and node-3
```
// node2
ip -f mpls route add 32 via inet 169.254.0.7 dev if_2_4_1
// node3
ip -f mpls route add 64 via inet 169.254.0.12 dev if_4_3_1
```
- Ping 192.168.0.11 (node4) from 192.168.0.1 (node1) (where routing
towards 192.168.0.1 is via IP route directly towards node1 from node4)
```
ping 192.168.0.11
```
- tcpdump on interface to capture ping packets wrapped within MPLS
header which inturn wrapped within IP6GRE header
```
16:43:41.121073 IP6
2401:db00:21:6048:feed::1 > 2401:db00:21:6048:feed::2:
DSTOPT GREv0, key=0x1, length 100:
MPLS (label 32, exp 0, ttl 255) (label 64, exp 0, [S], ttl 255)
IP 192.168.0.1 > 192.168.0.11:
ICMP echo request, id 1208, seq 45, length 64
0x0000: 6000 2cdb 006c 3c3f 2401 db00 0021 6048 `.,..l<?$....!`H
0x0010: feed 0000 0000 0001 2401 db00 0021 6048 ........$....!`H
0x0020: feed 0000 0000 0002 2f00 0401 0401 0100 ......../.......
0x0030: 2000 8847 0000 0001 0002 00ff 0004 01ff ...G............
0x0040: 4500 0054 3280 4000 ff01 c7cb c0a8 0001 E..T2.@.........
0x0050: c0a8 000b 0800 a8d7 04b8 002d 2d3c a05b ...........--<.[
0x0060: 0000 0000 bcd8 0100 0000 0000 1011 1213 ................
0x0070: 1415 1617 1819 1a1b 1c1d 1e1f 2021 2223 .............!"#
0x0080: 2425 2627 2829 2a2b 2c2d 2e2f 3031 3233 $%&'()*+,-./0123
0x0090: 3435 3637 4567
```
Signed-off-by: Saif Hasan <has@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2018-09-24
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Several fixes for BPF sockmap to only allow sockets being attached in
ESTABLISHED state, from John.
2) Fix up the license to LGPL/BSD for the libc compat header which contains
fallback helpers that libbpf and bpftool is using, from Jakub.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The E3 (r8a77990) supports two LVDS channels. Extend the binding to
support them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
|
|
Document the E3 (r8a77990) SoC in the R-Car DU bindings.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
|
|
bnxt_re_ib_reg acquires and releases the rtnl lock whenever it accesses
the L2 driver.
The following sequence can trigger a crash
Acquires the rtnl_lock ->
Registers roce driver callback with L2 driver ->
release the rtnl lock
bnxt_re acquires the rtnl_lock ->
Request for MSIx vectors ->
release the rtnl_lock
Issue happens when bnxt_re proceeds with remaining part of initialization
and L2 driver invokes bnxt_ulp_irq_stop as a part of bnxt_open_nic.
The crash is in bnxt_qplib_nq_stop_irq as the NQ structures are
not initialized yet,
<snip>
[ 3551.726647] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 3551.726656] IP: [<ffffffffc0840ee9>] bnxt_qplib_nq_stop_irq+0x59/0xb0 [bnxt_re]
[ 3551.726674] PGD 0
[ 3551.726679] Oops: 0002 1 SMP
...
[ 3551.726822] Hardware name: Dell Inc. PowerEdge R720/08RW36, BIOS 2.4.3 07/09/2014
[ 3551.726826] task: ffff97e30eec5ee0 ti: ffff97e3173bc000 task.ti: ffff97e3173bc000
[ 3551.726829] RIP: 0010:[<ffffffffc0840ee9>] [<ffffffffc0840ee9>]
bnxt_qplib_nq_stop_irq+0x59/0xb0 [bnxt_re]
...
[ 3551.726872] Call Trace:
[ 3551.726886] [<ffffffffc082cb9e>] bnxt_re_stop_irq+0x4e/0x70 [bnxt_re]
[ 3551.726899] [<ffffffffc07d6a53>] bnxt_ulp_irq_stop+0x43/0x70 [bnxt_en]
[ 3551.726908] [<ffffffffc07c82f4>] bnxt_reserve_rings+0x174/0x1e0 [bnxt_en]
[ 3551.726917] [<ffffffffc07cafd8>] __bnxt_open_nic+0x368/0x9a0 [bnxt_en]
[ 3551.726925] [<ffffffffc07cb62b>] bnxt_open_nic+0x1b/0x50 [bnxt_en]
[ 3551.726934] [<ffffffffc07cc62f>] bnxt_setup_mq_tc+0x11f/0x260 [bnxt_en]
[ 3551.726943] [<ffffffffc07d5f58>] bnxt_dcbnl_ieee_setets+0xb8/0x1f0 [bnxt_en]
[ 3551.726954] [<ffffffff890f983a>] dcbnl_ieee_set+0x9a/0x250
[ 3551.726966] [<ffffffff88fd6d21>] ? __alloc_skb+0xa1/0x2d0
[ 3551.726972] [<ffffffff890f72fa>] dcb_doit+0x13a/0x210
[ 3551.726981] [<ffffffff89003ff7>] rtnetlink_rcv_msg+0xa7/0x260
[ 3551.726989] [<ffffffff88ffdb00>] ? rtnl_unicast+0x20/0x30
[ 3551.726996] [<ffffffff88bf9dc8>] ? __kmalloc_node_track_caller+0x58/0x290
[ 3551.727002] [<ffffffff890f7326>] ? dcb_doit+0x166/0x210
[ 3551.727007] [<ffffffff88fd6d0d>] ? __alloc_skb+0x8d/0x2d0
[ 3551.727012] [<ffffffff89003f50>] ? rtnl_newlink+0x880/0x880
...
[ 3551.727104] [<ffffffff8911f7d5>] system_call_fastpath+0x1c/0x21
...
[ 3551.727164] RIP [<ffffffffc0840ee9>] bnxt_qplib_nq_stop_irq+0x59/0xb0 [bnxt_re]
[ 3551.727175] RSP <ffff97e3173bf788>
[ 3551.727177] CR2: 0000000000000000
Avoid this inconsistent state and system crash by acquiring
the rtnl lock for the entire duration of device initialization.
Re-factor the code to remove the rtnl lock from the individual function
and acquire and release it from the caller.
Fixes: 1ac5a4047975 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Fixes: 6e04b1035689 ("RDMA/bnxt_re: Fix broken RoCE driver due to recent L2 driver changes")
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Some of definitions in the code changed the meaning, unfortunately one
place missed the change.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Mauro briefly writes:
"media fixes for v4.19-rc5
some drivers and Kbuild fixes"
* tag 'media/v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: platform: fix cros-ec-cec build error
media: staging/media/mt9t031/Kconfig: remove bogus entry
media: i2c: mt9v111: Fix v4l2-ctrl error handling
media: camss: add missing includes
media: camss: Use managed memory allocations
media: camss: mark PM functions as __maybe_unused
media: af9035: prevent buffer overflow on write
media: video_function_calls.rst: drop obsolete video-set-attributes reference
|
|
After migration of a powerpc LPAR, the kernel executes code to
update the system state to reflect new platform characteristics.
Such changes include modifications to device tree properties provided
to the system by PHYP. Property notifications received by the
post_mobility_fixup() code are passed along to the kernel in general
through a call to of_update_property() which in turn passes such
events back to all modules through entries like the '.notifier_call'
function within the NUMA module.
When the NUMA module updates its state, it resets its event timer. If
this occurs after a previous call to stop_topology_update() or on a
system without VPHN enabled, the code runs into an unitialized timer
structure and crashes. This patch adds a safety check along this path
toward the problem code.
An example crash log is as follows.
ibmvscsi 30000081: Re-enabling adapter!
------------[ cut here ]------------
kernel BUG at kernel/time/timer.c:958!
Oops: Exception in kernel mode, sig: 5 [#1]
LE SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: nfsv3 nfs_acl nfs tcp_diag udp_diag inet_diag lockd unix_diag af_packet_diag netlink_diag grace fscache sunrpc xts vmx_crypto pseries_rng sg binfmt_misc ip_tables xfs libcrc32c sd_mod ibmvscsi ibmveth scsi_transport_srp dm_mirror dm_region_hash dm_log dm_mod
CPU: 11 PID: 3067 Comm: drmgr Not tainted 4.17.0+ #179
...
NIP mod_timer+0x4c/0x400
LR reset_topology_timer+0x40/0x60
Call Trace:
0xc0000003f9407830 (unreliable)
reset_topology_timer+0x40/0x60
dt_update_callback+0x100/0x120
notifier_call_chain+0x90/0x100
__blocking_notifier_call_chain+0x60/0x90
of_property_notify+0x90/0xd0
of_update_property+0x104/0x150
update_dt_property+0xdc/0x1f0
pseries_devicetree_update+0x2d0/0x510
post_mobility_fixup+0x7c/0xf0
migration_store+0xa4/0xc0
kobj_attr_store+0x30/0x60
sysfs_kf_write+0x64/0xa0
kernfs_fop_write+0x16c/0x240
__vfs_write+0x40/0x200
vfs_write+0xc8/0x240
ksys_write+0x5c/0x100
system_call+0x58/0x6c
Fixes: 5d88aa85c00b ("powerpc/pseries: Update CPU maps when device tree is updated")
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Michael Bringmann <mwb@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
https://git.linaro.org/people/daniel.lezcano/linux into timers/urgent
Pull clockevent fixed from Daniel Lezcano:
- Add the CLOCK_SOURCE_SUSPEND_NONSTOP for non-am43 SoCs (Keerthy)
- Fix set_next_event handler for the fttmr010 (Tao Ren)
|
|
This patch fixes skb_shared area, which will be corrupted
upon reception of 4K jumbo packets.
Originally build_skb usage purpose was to reuse page for skb to eliminate
needs of extra fragments. But that logic does not take into account that
skb_shared_info should be reserved at the end of skb data area.
In case packet data consumes all the page (4K), skb_shinfo location
overflows the page. As a consequence, __build_skb zeroed shinfo data above
the allocated page, corrupting next page.
The issue is rarely seen in real life because jumbo are normally larger
than 4K and that causes another code path to trigger.
But it 100% reproducible with simple scapy packet, like:
sendp(IP(dst="192.168.100.3") / TCP(dport=443) \
/ Raw(RandString(size=(4096-40))), iface="enp1s0")
Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code")
Reported-by: Friedemann Gerold <f.gerold@b-c-s.de>
Reported-by: Michael Rauch <michael@rauch.be>
Signed-off-by: Friedemann Gerold <f.gerold@b-c-s.de>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eric Dumazet says:
====================
netpoll: avoid capture effects for NAPI drivers
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC).
This capture, showing one ksoftirqd eating all cycles
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
It seems that all networking drivers that do use NAPI
for their TX completions, should not provide a ndo_poll_controller() :
Most NAPI drivers have netpoll support already handled
in core networking stack, since netpoll_poll_dev()
uses poll_napi(dev) to iterate through registered
NAPI contexts for a device.
This patch series take care of the first round, we will
handle other drivers in future rounds.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
tun uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
nfp uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Tested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
bnxt uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
bnx2x uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
mlx5 uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
mlx4 uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
i40evf uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ice uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
igb uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ixgb uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
This also removes a problematic use of disable_irq() in
a context it is forbidden, as explained in commit
af3e0fcf7887 ("8139too: Use disable_irq_nosync() in
rtl8139_poll_controller()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
lasts for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
fm10k uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ixgbevf uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ixgbe uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Reported-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Song Liu <songliubraving@fb.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We want to allow NAPI drivers to no longer provide
ndo_poll_controller() method, as it has been proven problematic.
team driver must not look at its presence, but instead call
netpoll_poll_dev() which factorize the needed actions.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
It seems that all networking drivers that do use NAPI
for their TX completions, should not provide a ndo_poll_controller().
NAPI drivers have netpoll support already handled
in core networking stack, since netpoll_poll_dev()
uses poll_napi(dev) to iterate through registered
NAPI contexts for a device.
This patch allows netpoll_poll_dev() to process NAPI
contexts even for drivers not providing ndo_poll_controller(),
allowing for following patches in NAPI drivers.
Also we export netpoll_poll_dev() so that it can be called
by bonding/team drivers in following patches.
Reported-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Song Liu <songliubraving@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the aspeed MATCH1 register is updated to <current_count -
cycles> in set_next_event handler, with the assumption that COUNT
register value is preserved when the timer is disabled and it continues
decrementing after the timer is enabled. But the assumption is wrong:
RELOAD register is loaded into COUNT register when the aspeed timer is
enabled, which means the next event may be delayed because timer
interrupt won't be generated until <0xFFFFFFFF - current_count +
cycles>.
The problem can be fixed by updating RELOAD register to <cycles>, and
COUNT register will be re-loaded when the timer is enabled and interrupt
is generated when COUNT register overflows.
The test result on Facebook Backpack-CMM BMC hardware (AST2500) shows
the issue is fixed: without the patch, usleep(100) suspends the process
for several milliseconds (and sometimes even over 40 milliseconds);
after applying the fix, usleep(100) takes averagely 240 microseconds to
return under the same workload level.
Signed-off-by: Tao Ren <taoren@fb.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Use DECLARE_* not DEFINE_*
Fixes: 8360ed6745df ("RDS: IB: Use DEFINE_PER_CPU_SHARED_ALIGNED for rds_ib_stats")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Lee writes:
"MFD fixes for v4.19
- Fix Dialog DA9063 regulator constraints issue causing failure in
probe
- Fix OMAP Device Tree compatible strings to match DT"
* tag 'mfd-fixes-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: omap-usb-host: Fix dts probe of children
mfd: da9063: Fix DT probing with constraints
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Juergen writes:
"xen:
Two small fixes for xen drivers."
* tag 'for-linus-4.19d-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: issue warning message when out of grant maptrack entries
xen/x86/vpmu: Zero struct pt_regs before calling into sample handling code
|
|
Jens writes:
"Just a single fix in this pull request, fixing a regression in
/proc/diskstats caused by the unification of timestamps."
* tag 'for-linus-20180922' of git://git.kernel.dk/linux-block:
block: use nanosecond resolution for iostat
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Thomas writes:
"A set of fixes for x86:
- Resolve the kvmclock regression on AMD systems with memory
encryption enabled. The rework of the kvmclock memory allocation
during early boot results in encrypted storage, which is not
shareable with the hypervisor. Create a new section for this data
which is mapped unencrypted and take care that the later
allocations for shared kvmclock memory is unencrypted as well.
- Fix the build regression in the paravirt code introduced by the
recent spectre v2 updates.
- Ensure that the initial static page tables cover the fixmap space
correctly so early console always works. This worked so far by
chance, but recent modifications to the fixmap layout can -
depending on kernel configuration - move the relevant entries to a
different place which is not covered by the initial static page
tables.
- Address the regressions and issues which got introduced with the
recent extensions to the Intel Recource Director Technology code.
- Update maintainer entries to document reality"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Expand static page table for fixmap space
MAINTAINERS: Add X86 MM entry
x86/intel_rdt: Add Reinette as co-maintainer for RDT
MAINTAINERS: Add Borislav to the x86 maintainers
x86/paravirt: Fix some warning messages
x86/intel_rdt: Fix incorrect loop end condition
x86/intel_rdt: Fix exclusive mode handling of MBA resource
x86/intel_rdt: Fix incorrect loop end condition
x86/intel_rdt: Do not allow pseudo-locking of MBA resource
x86/intel_rdt: Fix unchecked MSR access
x86/intel_rdt: Fix invalid mode warning when multiple resources are managed
x86/intel_rdt: Global closid helper to support future fixes
x86/intel_rdt: Fix size reporting of MBA resource
x86/intel_rdt: Fix data type in parsing callbacks
x86/kvm: Use __bss_decrypted attribute in shared variables
x86/mm: Add .bss..decrypted section to hold shared variables
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Thomas writes:
"- Provide a strerror_r wrapper so lib/bpf can be built on systems
without _GNU_SOURCE
- Unbreak the man page generator when building out of tree"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf Documentation: Fix out-of-tree asciidoctor man page generation
tools lib bpf: Provide wrapper for strerror_r to build in !_GNU_SOURCE systems
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Thomas writes:
"Make the EFI arm stub device tree loader default on to unbreak
existing EFI boot loaders which do not have DTB support."
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/libstub/arm: default EFI_ARMSTUB_DTB_LOADER to y
|
|
So it should not fail with EPERM even though it is no longer implemented...
This is a fix for:
(userns)$ egrep ^Cap /proc/self/status
CapInh: 0000003fffffffff
CapPrm: 0000003fffffffff
CapEff: 0000003fffffffff
CapBnd: 0000003fffffffff
CapAmb: 0000003fffffffff
(userns)$ tcpdump -i usb_rndis0
tcpdump: WARNING: usb_rndis0: SIOCETHTOOL(ETHTOOL_GUFO) ioctl failed: Operation not permitted
Warning: Kernel filter failed: Bad file descriptor
tcpdump: can't remove kernel filter: Bad file descriptor
With this change it returns EOPNOTSUPP instead of EPERM.
See also https://github.com/the-tcpdump-group/libpcap/issues/689
Fixes: 08a00fea6de2 "net: Remove references to NETIF_F_UFO from ethtool."
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With address_space_operations missing for device dax, namely the
.set_page_dirty, we hit a kernel warning when running destructive
ndctl unit test: make TESTS=device-dax check
WARNING: CPU: 3 PID: 7380 at fs/buffer.c:581 __set_page_dirty+0xb1/0xc0
Setting address_space_operations to noop_set_page_dirty and
noop_invalidatepage for device dax to prevent fallback to
__set_page_dirty_buffers() and block_invalidatepage() respectively.
Fixes: 2232c6382a ("device-dax: Enable page_mapping()")
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Clang warns when two declarations' section attributes don't match.
net/rds/ib_stats.c:40:1: warning: section does not match previous
declaration [-Wsection]
DEFINE_PER_CPU_SHARED_ALIGNED(struct rds_ib_statistics, rds_ib_stats);
^
./include/linux/percpu-defs.h:142:2: note: expanded from macro
'DEFINE_PER_CPU_SHARED_ALIGNED'
DEFINE_PER_CPU_SECTION(type, name,
PER_CPU_SHARED_ALIGNED_SECTION) \
^
./include/linux/percpu-defs.h:93:9: note: expanded from macro
'DEFINE_PER_CPU_SECTION'
extern __PCPU_ATTRS(sec) __typeof__(type) name;
\
^
./include/linux/percpu-defs.h:49:26: note: expanded from macro
'__PCPU_ATTRS'
__percpu __attribute__((section(PER_CPU_BASE_SECTION sec)))
\
^
net/rds/ib.h:446:1: note: previous attribute is here
DECLARE_PER_CPU(struct rds_ib_statistics, rds_ib_stats);
^
./include/linux/percpu-defs.h:111:2: note: expanded from macro
'DECLARE_PER_CPU'
DECLARE_PER_CPU_SECTION(type, name, "")
^
./include/linux/percpu-defs.h:87:9: note: expanded from macro
'DECLARE_PER_CPU_SECTION'
extern __PCPU_ATTRS(sec) __typeof__(type) name
^
./include/linux/percpu-defs.h:49:26: note: expanded from macro
'__PCPU_ATTRS'
__percpu __attribute__((section(PER_CPU_BASE_SECTION sec)))
\
^
1 warning generated.
The initial definition was added in commit ec16227e1414 ("RDS/IB:
Infiniband transport") and the cache aligned definition was added in
commit e6babe4cc4ce ("RDS/IB: Stats and sysctls") right after. The
definition probably should have been updated in net/rds/ib.h, which is
what this patch does.
Link: https://github.com/ClangBuiltLinux/linux/issues/114
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Klaus Kusche reported that the I/O busy time in /proc/diskstats was not
updating properly on 4.18. This is because we started using ktime to
track elapsed time, and we convert nanoseconds to jiffies when we update
the partition counter. However, this gets rounded down, so any I/Os that
take less than a jiffy are not accounted for. Previously in this case,
the value of jiffies would sometimes increment while we were doing I/O,
so at least some I/Os were accounted for.
Let's convert the stats to use nanoseconds internally. We still report
milliseconds as before, now more accurately than ever. The value is
still truncated to 32 bits for backwards compatibility.
Fixes: 522a777566f5 ("block: consolidate struct request timestamp fields")
Cc: stable@vger.kernel.org
Reported-by: Klaus Kusche <klaus.kusche@computerix.info>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
