Age | Commit message (Collapse) | Author |
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"i2c-host fixes for v6.12-rc7 (from Andi):
- Fix designware incorrect behavior when concluding a transmission
- Fix Mule multiplexer error value evaluation"
* tag 'i2c-for-6.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: designware: do not hold SCL low when I2C_DYNAMIC_TAR_UPDATE is not set
i2c: muxes: Fix return value check in mule_i2c_mux_probe()
|
|
If the caller supplies an iocb->ki_pos value that is close to the
filesystem upper limit, and an iterator with a count that causes us to
overflow that limit, then filemap_read() enters an infinite loop.
This behaviour was discovered when testing xfstests generic/525 with the
"localio" optimisation for loopback NFS mounts.
Reported-by: Mike Snitzer <snitzer@kernel.org>
Fixes: c2a9737f45e2 ("vfs,mm: fix a dead loop in truncate_inode_pages_range()")
Tested-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Lewis' original GPIO driver patchset didn't add MAINTAINERS coverage of
the driver and I forgot to add it to the existing entry. Make up for the
minimal amount of lost time.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20241107-chewable-spoiler-3e7dd58d3e8d@spud
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Borislav Petkov:
- Make sure GICv3 controller interrupt activation doesn't race with a
concurrent deactivation due to propagation delays of the register
write
* tag 'irq_urgent_for_v6.12_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3: Force propagation of the active state with a read-back
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"20 hotfixes, 14 of which are cc:stable.
Three affect DAMON. Lorenzo's five-patch series to address the
mmap_region error handling is here also.
Apart from that, various singletons"
* tag 'mm-hotfixes-stable-2024-11-09-22-40' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mailmap: add entry for Thorsten Blum
ocfs2: remove entry once instead of null-ptr-dereference in ocfs2_xa_remove()
signal: restore the override_rlimit logic
fs/proc: fix compile warning about variable 'vmcore_mmap_ops'
ucounts: fix counter leak in inc_rlimit_get_ucounts()
selftests: hugetlb_dio: check for initial conditions to skip in the start
mm: fix docs for the kernel parameter ``thp_anon=``
mm/damon/core: avoid overflow in damon_feed_loop_next_input()
mm/damon/core: handle zero schemes apply interval
mm/damon/core: handle zero {aggregation,ops_update} intervals
mm/mlock: set the correct prev on failure
objpool: fix to make percpu slot allocation more robust
mm/page_alloc: keep track of free highatomic
mm: resolve faulty mmap_region() error path behaviour
mm: refactor arch_calc_vm_flag_bits() and arm64 MTE handling
mm: refactor map_deny_write_exec()
mm: unconditionally close VMAs on error
mm: avoid unsafe VMA hook invocation when error arises on mmap hook
mm/thp: fix deferred split unqueue naming and locking
mm/thp: fix deferred split queue not partially_mapped
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt fixes from Greg KH:
"Here are some small remaining USB and Thunderbolt fixes and device ids
for 6.12-rc7. Included in here are:
- new USB serial driver device ids
- thunderbolt driver fixes for reported problems
- typec bugfixes
- dwc3 driver fix
- musb driver fix
All of these have been in linux-next this past week with no reported
issues"
* tag 'usb-6.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: qcserial: add support for Sierra Wireless EM86xx
thunderbolt: Fix connection issue with Pluggable UD-4VPD dock
usb: typec: fix potential out of bounds in ucsi_ccg_update_set_new_cam_cmd()
usb: dwc3: fix fault at system suspend if device was already runtime suspended
usb: typec: qcom-pmic: init value of hdr_len/txbuf_len earlier
usb: musb: sunxi: Fix accessing an released usb phy
USB: serial: io_edgeport: fix use after free in debug printk
USB: serial: option: add Quectel RG650V
USB: serial: option: add Fibocom FG132 0x0112 composition
thunderbolt: Add only on-board retimers when !CONFIG_USB4_DEBUGFS_MARGINING
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are two small memory leak fixes for the vchiq_arm staging driver
that have been sitting in my tree for weeks and should get merged for
6.12-rc7 so that people don't keep tripping over them.
They both have been in linux-next for a while with no reported
problems"
* tag 'staging-6.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: vchiq_arm: Use devm_kzalloc() for drv_mgmt allocation
staging: vchiq_arm: Use devm_kzalloc() for vchiq_arm_state allocation
|
|
ib_map_mr_sg() allows ULPs to specify NULL as the sg_offset argument.
The driver needs to check whether it is a NULL pointer before
dereferencing it.
Fixes: d387d4b54eb8 ("RDMA/hns: Fix missing pagesize and alignment check in FRMR")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20241108075743.2652258-3-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
The FENCE indicator in hns WQE doesn't ensure that response data from
a previous Read/Atomic operation has been written to the requester's
memory before the subsequent Send/Write operation is processed. This
may result in the subsequent Send/Write operation accessing the original
data in memory instead of the expected response data.
Unlike FENCE, the SO (Strong Order) indicator blocks the subsequent
operation until the previous response data is written to memory and a
bresp is returned. Set the SO indicator instead of FENCE to maintain
strict order.
Fixes: 9a4435375cd1 ("IB/hns: Add driver files for hns RoCE driver")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20241108075743.2652258-2-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
A100 perf1 hava MicroSD slot and on-board eMMC module, add support for them.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Signed-off-by: Cody Eksal <masterr3c0rd@epochal.quest>
Link: https://patch.msgid.link/20241031070232.1793078-11-masterr3c0rd@epochal.quest
[wens@csie.org: cherry-picked out of series and GPIO header inclusion added]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The way InvenSense MPU-6050 accelerometer is mounted on the user-facing side
of the Pine64 PinePhone mainboard, which makes it rotated 90 degrees counter-
clockwise, [1] requires the accelerometer's x- and y-axis to be swapped, and
the direction of the accelerometer's y-axis to be inverted.
Rectify this by adding a mount-matrix to the accelerometer definition in the
Pine64 PinePhone dtsi file.
[1] https://files.pine64.org/doc/PinePhone/PinePhone%20mainboard%20bottom%20placement%20v1.1%2020191031.pdf
Fixes: 91f480d40942 ("arm64: dts: allwinner: Add initial support for Pine64 PinePhone")
Cc: stable@vger.kernel.org
Suggested-by: Ondrej Jirman <megi@xff.cz>
Suggested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Link: https://patch.msgid.link/129f0c754d071cca1db5d207d9d4a7bd9831dff7.1726773282.git.dsimic@manjaro.org
[wens@csie.org: Replaced Helped-by with Suggested-by]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Add a driver for the random number generator present on the Broadcom
BCM74110 SoC.
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add a binding for the random number generator used on the BCM74110.
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
In commit 24cc57d8faaa ("padata: Honor the caller's alignment in case of
chunk_size 0"), the line 'ps.chunk_size = max(ps.chunk_size, 1ul)' was
added, making 'ps.chunk_size = 1U' redundant and never executed.
Signed-off-by: Zicheng Qu <quzicheng@huawei.com>
Acked-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The commit 320406cb60b6 ("crypto: inside-secure - Replace generic aes
with libaes") replaced crypto_alloc_cipher() with kmalloc(), but did not
modify the handling of the return value. When kmalloc() returns NULL,
PTR_ERR_OR_ZERO(NULL) returns 0, but in fact, the memory allocation has
failed, and -ENOMEM should be returned.
Fixes: 320406cb60b6 ("crypto: inside-secure - Replace generic aes with libaes")
Signed-off-by: Li Huafei <lihuafei1@huawei.com>
Acked-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The adf_init_aer() won't destroy device_reset_wq when alloc_workqueue()
for device_sriov_wq failed. Add destroy_workqueue for device_reset_wq to
fix this issue.
Fixes: 4469f9b23468 ("crypto: qat - re-enable sriov after pf reset")
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Commit 1e562deacecc ("crypto: rsassa-pkcs1 - Migrate to sig_alg backend")
enforced that rsassa-pkcs1 sign/verify operations specify a hash
algorithm. That is necessary because per RFC 8017 sec 8.2, a hash
algorithm identifier must be prepended to the hash before generating or
verifying the signature ("Full Hash Prefix").
However the commit went too far in that it changed user space behavior:
KEYCTL_PKEY_QUERY system calls now return -EINVAL unless they specify a
hash algorithm. Intel Wireless Daemon (iwd) is one application issuing
such system calls (for EAP-TLS).
Closer analysis of the Embedded Linux Library (ell) used by iwd reveals
that the problem runs even deeper: When iwd uses TLS 1.1 or earlier, it
not only queries for keys, but performs sign/verify operations without
specifying a hash algorithm. These legacy TLS versions concatenate an
MD5 to a SHA-1 hash and omit the Full Hash Prefix:
https://git.kernel.org/pub/scm/libs/ell/ell.git/tree/ell/tls-suites.c#n97
TLS 1.1 was deprecated in 2021 by RFC 8996, but removal of support was
inadvertent in this case. It probably should be coordinated with iwd
maintainers first.
So reinstate support for such legacy protocols by defaulting to hash
algorithm "none" which uses an empty Full Hash Prefix.
If it is later on decided to remove TLS 1.1 support but still allow
KEYCTL_PKEY_QUERY without a hash algorithm, that can be achieved by
reverting the present commit and replacing it with the following patch:
https://lore.kernel.org/r/ZxalYZwH5UiGX5uj@wunner.de/
It's worth noting that Python's cryptography library gained support for
such legacy use cases very recently, so they do seem to still be a thing.
The Python developers identified IKE version 1 as another protocol
omitting the Full Hash Prefix:
https://github.com/pyca/cryptography/issues/10226
https://github.com/pyca/cryptography/issues/5495
The author of those issues, Zoltan Kelemen, spent considerable effort
searching for test vectors but only found one in a 2019 blog post by
Kevin Jones. Add it to testmgr.h to verify correctness of this feature.
Examination of wpa_supplicant as well as various IKE daemons (libreswan,
strongswan, isakmpd, raccoon) has determined that none of them seems to
use the kernel's Key Retention Service, so iwd is the only affected user
space application known so far.
Fixes: 1e562deacecc ("crypto: rsassa-pkcs1 - Migrate to sig_alg backend")
Reported-by: Klara Modin <klarasmodin@gmail.com>
Tested-by: Klara Modin <klarasmodin@gmail.com>
Closes: https://lore.kernel.org/r/2ed09a22-86c0-4cf0-8bda-ef804ccb3413@gmail.com/
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Fix typo in comment:
requeust->request,
Removve->Remove,
notthing->nothing.
Signed-off-by: Yu Jiaoliang <yujiaoliang@vivo.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/20241108133913.3068782-3-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In case of an early failure in dasd_init, dasd_proc_init is never
called and /proc/dasd* files are never created. That can happen, for
example, if an incompatible or incorrect argument is provided to the
dasd_mod.dasd= kernel parameter.
However, the attempted removal of /proc/dasd* files causes 8 warnings
and backtraces in this case. 4 on the error path within dasd_init and
4 when the dasd module is unloaded. Notice the "removing permanent
/proc entry 'devices'" message that is caused by the dasd_proc_exit
function trying to remove /proc/devices instead of /proc/dasd/devices
since dasd_proc_root_entry is NULL and /proc/devices is indeed
permanent. Example:
------------[ cut here ]------------
removing permanent /proc entry 'devices'
WARNING: CPU: 6 PID: 557 at fs/proc/generic.c:701 remove_proc_entry+0x22e/0x240
CPU: 6 PID: 557 Comm: modprobe Not tainted 6.10.5-1-default #1
openSUSE Tumbleweed f6917bfd6e5a5c7a7e900e0e3b517786fb5c6301
Hardware name: QEMU 8561 QEMU (KVM/Linux)
Krnl PSW : 0704c00180000000 000003fffed0e9f2 (remove_proc_entry+0x232/0x240)
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:0 PM:0 RI:0 EA:3
Krnl GPRS: 000003ff00000027 000003ff00000023 0000000000000028 000002f200000000
000002f3f05bec20 0000037ffecfb7d0 000003ffffdabab0 000003ff7ee4ec72
000003ff7ee4ec72 0000000000000007 000002f280e22600 000002f280e22688
000003ffa252cfa0 0000000000010000 000003fffed0e9ee 0000037ffecfba38
Krnl Code: 000003fffed0e9e2: c020004e7017 larl %r2,000003ffff6dca10
000003fffed0e9e8: c0e5ffdfad24 brasl %r14,000003fffe904430
#000003fffed0e9ee: af000000 mc 0,0
>000003fffed0e9f2: a7f4ff4c brc 15,000003fffed0e88a
000003fffed0e9f6: 0707 bcr 0,%r7
000003fffed0e9f8: 0707 bcr 0,%r7
000003fffed0e9fa: 0707 bcr 0,%r7
000003fffed0e9fc: 0707 bcr 0,%r7
Call Trace:
[<000003fffed0e9f2>] remove_proc_entry+0x232/0x240
([<000003fffed0e9ee>] remove_proc_entry+0x22e/0x240)
[<000003ff7ef5a084>] dasd_proc_exit+0x34/0x60 [dasd_mod]
[<000003ff7ef560c2>] dasd_exit+0x22/0xc0 [dasd_mod]
[<000003ff7ee5a26e>] dasd_init+0x26e/0x280 [dasd_mod]
[<000003fffe8ac9d0>] do_one_initcall+0x40/0x220
[<000003fffe9bc758>] do_init_module+0x78/0x260
[<000003fffe9bf3a6>] __do_sys_init_module+0x216/0x250
[<000003ffff37ac9e>] __do_syscall+0x24e/0x2d0
[<000003ffff38cca8>] system_call+0x70/0x98
Last Breaking-Event-Address:
[<000003fffef7ea20>] __s390_indirect_jump_r14+0x0/0x10
---[ end trace 0000000000000000 ]---
------------[ cut here ]------------
While the cause is a user failure, the dasd module should handle the
situation more gracefully. One of the simplest solutions is to make
removal of the /proc/dasd* entries idempotent.
Signed-off-by: Miroslav Franc <mfranc@suse.cz>
[ sth: shortened if clause ]
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/20241108133913.3068782-2-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/song/md into for-6.13/block
Pull raid5 fix from Song.
* tag 'md-6.13-20241107' of https://git.kernel.org/pub/scm/linux/kernel/git/song/md:
MAINTAINERS: Make Yu Kuai co-maintainer of md/raid subsystem
md/raid5: Wait sync io to finish before changing group cnt
|
|
PAGE_SIZE may be 64K, and the max block size can be PAGE_SIZE, so any
variable for holding block size can't be defined as 'unsigned short'.
Unfortunately commit 473516b36193 ("loop: use the atomic queue limits
update API") passes 'bsize' with type of 'unsigned short' to
loop_reconfigure_limits(), and causes LTP/ioctl_loop06 test failure:
12 ioctl_loop06.c:76: TINFO: Using LOOP_SET_BLOCK_SIZE with arg > PAGE_SIZE
13 ioctl_loop06.c:59: TFAIL: Set block size succeed unexpectedly
...
18 ioctl_loop06.c:76: TINFO: Using LOOP_CONFIGURE with block_size > PAGE_SIZE
19 ioctl_loop06.c:59: TFAIL: Set block size succeed unexpectedly
Fixes the issue by defining 'block size' variable with 'unsigned int', which is
aligned with block layer's definition.
(improve commit log & add fixes tag)
Fixes: 473516b36193 ("loop: use the atomic queue limits update API")
Cc: John Garry <john.g.garry@oracle.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Li Wang <liwang@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20241109022744.1126003-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
It is currently impossible to delete individual FDB entries (as opposed
to flushing) that were added with a VLAN that no longer exists:
# ip link add name dummy1 up type dummy
# ip link add name br1 up type bridge vlan_filtering 1
# ip link set dev dummy1 master br1
# bridge fdb add 00:11:22:33:44:55 dev dummy1 master static vlan 1
# bridge vlan del vid 1 dev dummy1
# bridge fdb get 00:11:22:33:44:55 br br1 vlan 1
00:11:22:33:44:55 dev dummy1 vlan 1 master br1 static
# bridge fdb del 00:11:22:33:44:55 dev dummy1 master vlan 1
RTNETLINK answers: Invalid argument
# bridge fdb get 00:11:22:33:44:55 br br1 vlan 1
00:11:22:33:44:55 dev dummy1 vlan 1 master br1 static
This is in contrast to MDB entries that can be deleted after the VLAN
was deleted:
# bridge vlan add vid 10 dev dummy1
# bridge mdb add dev br1 port dummy1 grp 239.1.1.1 permanent vid 10
# bridge vlan del vid 10 dev dummy1
# bridge mdb get dev br1 grp 239.1.1.1 vid 10
dev br1 port dummy1 grp 239.1.1.1 permanent vid 10
# bridge mdb del dev br1 port dummy1 grp 239.1.1.1 permanent vid 10
# bridge mdb get dev br1 grp 239.1.1.1 vid 10
Error: bridge: MDB entry not found.
Align the two interfaces and allow user space to delete FDB entries that
were added with a VLAN that no longer exists:
# ip link add name dummy1 up type dummy
# ip link add name br1 up type bridge vlan_filtering 1
# ip link set dev dummy1 master br1
# bridge fdb add 00:11:22:33:44:55 dev dummy1 master static vlan 1
# bridge vlan del vid 1 dev dummy1
# bridge fdb get 00:11:22:33:44:55 br br1 vlan 1
00:11:22:33:44:55 dev dummy1 vlan 1 master br1 static
# bridge fdb del 00:11:22:33:44:55 dev dummy1 master vlan 1
# bridge fdb get 00:11:22:33:44:55 br br1 vlan 1
Error: Fdb entry not found.
Add a selftest to make sure this behavior does not regress:
# ./rtnetlink.sh -t kci_test_fdb_del
PASS: bridge fdb del
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Andy Roulin <aroulin@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20241105133954.350479-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the mlx5_eq_comp_int() interrupt handler schedules a tasklet
to call mlx5_cq_tasklet_cb() if it processes any completions. For CQs
whose completions don't need to be processed in tasklet context, this
adds unnecessary overhead. In a heavy TCP workload, we see 4% of CPU
time spent on the tasklet_trylock() in tasklet_action_common(), with a
smaller amount spent on the atomic operations in tasklet_schedule(),
tasklet_clear_sched(), and locking the spinlock in mlx5_cq_tasklet_cb().
TCP completions are handled by mlx5e_completion_event(), which schedules
NAPI to poll the queue, so they don't need tasklet processing.
Schedule the tasklet in mlx5_add_cq_to_tasklet() instead to avoid this
overhead. mlx5_add_cq_to_tasklet() is responsible for enqueuing the CQs
to be processed in tasklet context, so it can schedule the tasklet. CQs
that need tasklet processing have their interrupt comp handler set to
mlx5_add_cq_to_tasklet(), so they will schedule the tasklet. CQs that
don't need tasklet processing won't schedule the tasklet. To avoid
scheduling the tasklet multiple times during the same interrupt, only
schedule the tasklet in mlx5_add_cq_to_tasklet() if the tasklet work
queue was empty before the new CQ was pushed to it.
The additional branch in mlx5_add_cq_to_tasklet(), called for each EQE,
may add a small cost for the userspace Infiniband CQs whose completions
are processed in tasklet context. But this seems worth it to avoid the
tasklet overhead for CQs that don't need it.
Note that the mlx4 driver works the same way: it schedules the tasklet
in mlx4_add_cq_to_tasklet() and only if the work queue was empty before.
Signed-off-by: Caleb Sander Mateos <csander@purestorage.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Acked-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://patch.msgid.link/20241105204000.1807095-1-csander@purestorage.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 55d42a0c3f9c ("selftests: net: add a test for closing
a netlink socket ith dump in progress") added a new test
but did not add it to gitignore.
Reviewed-by: Joe Damato <jdamato@fastly.com>
Link: https://patch.msgid.link/20241108004731.2979878-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The 'state' can't be NULL, we should check crtc_state.
Fix warning:
drivers/gpu/drm/rockchip/rockchip_drm_vop.c:1096
vop_plane_atomic_async_check() warn: variable dereferenced before check
'state' (see line 1077)
Fixes: 5ddb0bd4ddc3 ("drm/atomic: Pass the full state to planes async atomic check and update")
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20241021072818.61621-1-andyshrk@163.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-current
i2c-host fixes for v6.12-rc7
In designware an incorrect behavior has been fixes when
concluding a transmission.
Fixed return error value evaluation in the Mule multiplexer.
|
|
The tx_bytes should consider the actual size of the Ethernet frames
without the SPI encapsulation. But we still need to take care of
Ethernet padding.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20241108114343.6174-3-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Gilad Naaman says:
====================
Improve neigh_flush_dev performance
This patchsets improves the performance of neigh_flush_dev.
Currently, the only way to implement it requires traversing
all neighbours known to the kernel, across all network-namespaces.
This means that some flows are slowed down as a function of neigh-scale,
even if the specific link they're handling has little to no neighbours.
In order to solve this, this patchset adds a netdev->neighbours list,
as well as making the original linked-list doubly-, so that it is
possible to unlink neighbours without traversing the hash-bucket to
obtain the previous neighbour.
The original use-case we encountered was mass-deletion of links (12K
VLANs) while there are 50K ARPs and 50K NDPs in the system; though the
slowdowns would also appear when the links are set down.
====================
Link: https://patch.msgid.link/20241107160444.2913124-1-gnaaman@drivenets.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Create a mapping between a netdev and its neighoburs,
allowing for much cheaper flushes.
Signed-off-by: Gilad Naaman <gnaaman@drivenets.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20241107160444.2913124-7-gnaaman@drivenets.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the now-unused neighbour::next pointer, leaving struct neighbour
solely with the hlist_node implementation.
Signed-off-by: Gilad Naaman <gnaaman@drivenets.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241107160444.2913124-6-gnaaman@drivenets.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove all usage of the bare neighbour::next pointer,
replacing them with neighbour::hash and its for_each macro.
Signed-off-by: Gilad Naaman <gnaaman@drivenets.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241107160444.2913124-5-gnaaman@drivenets.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert seq_file-related neighbour functionality to use neighbour::hash
and the related for_each macro.
Signed-off-by: Gilad Naaman <gnaaman@drivenets.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241107160444.2913124-4-gnaaman@drivenets.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce neigh_for_each_in_bucket in neighbour.h, to help iterate over
the neighbour table more succinctly.
Signed-off-by: Gilad Naaman <gnaaman@drivenets.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241107160444.2913124-3-gnaaman@drivenets.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a doubly-linked node to neighbours, so that they
can be deleted without iterating the entire bucket they're in.
Signed-off-by: Gilad Naaman <gnaaman@drivenets.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241107160444.2913124-2-gnaaman@drivenets.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Heiner Kallweit says:
====================
r8169: improve wol/suspend-related code
This series improves wol/suspend-related code parts.
====================
Link: https://patch.msgid.link/be734d10-37f7-4830-b7c2-367c0a656c08@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Vendor drivers r8125/r8126 apply this additional magic setting when
enabling WAKE_PHY, so do the same here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/51130715-45be-4db5-abb7-05d87e1f5df9@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make use of new helper r8169_mod_reg8_cond() and move from a switch()
to an if() clause. Benefit is that we don't have to touch this piece of
code each time support for a new chip version is added.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/e1ccdb85-a4ed-4800-89c2-89770ff06452@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add helper r8169_mod_reg8_cond() what allows to significantly simplify
__rtl8169_set_wol().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/697b197a-8eac-40c6-8847-27093cacec36@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fix from Chuck Lever:
- Fix a v6.12-rc regression when exporting ext4 filesystems with NFSD
* tag 'nfsd-6.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
NFSD: Fix READDIR on NFSv3 mounts of ext4 exports
|
|
Pull smb client fix from Steve French:
"Fix net namespace refcount use after free issue"
* tag 'v6.12-rc6-smb3-client-fix' of git://git.samba.org/sfrench/cifs-2.6:
smb: client: Fix use-after-free of network namespace.
|
|
Pull block fix from Jens Axboe:
"Single fix for an issue triggered with PROVE_RCU=y, with nvme using
the wrong iterators for an SRCU protected list"
* tag 'block-6.12-20241108' of git://git.kernel.dk/linux:
nvme/host: Fix RCU list traversal to use SRCU primitive
|
|
balance_scx()
sched_ext dispatches tasks from the BPF scheduler from balance_scx() and
thus every pick_task_scx() call must be preceded by balance_scx(). While
this usually holds, due to a bug, there are cases where the fair class's
balance() returns true indicating that it has tasks to run on the CPU and
thus terminating balance() calls but fails to actually find the next task to
run when pick_task() is called. In such cases, pick_task_scx() can be called
without preceding balance_scx().
Detect this condition using SCX_RQ_BAL_PENDING flags. If detected, keep
running the previous task if possible and avoid stalling from entering idle
without balancing.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/Ztj_h5c2LYsdXYbA@slm.duckdns.org
|
|
4c30f5ce4f7a ("sched_ext: Implement scx_bpf_dispatch[_vtime]_from_dsq()")
added four kfuncs for dispatching while iterating. They are allowed from the
dispatch and unlocked contexts but two of the kfuncs were only added in the
dispatch section. Add missing declarations in the unlocked section.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 4c30f5ce4f7a ("sched_ext: Implement scx_bpf_dispatch[_vtime]_from_dsq()")
|
|
Do not walk through the domain hierarchy when the required scope is not
supported by this domain. This is the same approach as for filesystem
and network restrictions.
Cc: Mikhail Ivanov <ivanov.mikhail1@huawei-partners.com>
Cc: Tahera Fahimi <fahimitahera@gmail.com>
Reviewed-by: Günther Noack <gnoack@google.com>
Link: https://lore.kernel.org/r/20241109110856.222842-4-mic@digikod.net
Signed-off-by: Mickaël Salaün <mic@digikod.net>
|
|
Replace get_raw_handled_net_accesses() and get_current_net_domain() with
a call to landlock_get_applicable_domain().
Cc: Konstantin Meskhidze <konstantin.meskhidze@huawei.com>
Cc: Mikhail Ivanov <ivanov.mikhail1@huawei-partners.com>
Reviewed-by: Günther Noack <gnoack@google.com>
Link: https://lore.kernel.org/r/20241109110856.222842-3-mic@digikod.net
Signed-off-by: Mickaël Salaün <mic@digikod.net>
|
|
Replace get_raw_handled_fs_accesses() with a generic
landlock_union_access_masks(), and replace get_fs_domain() with a
generic landlock_get_applicable_domain(). These helpers will also be
useful for other types of access.
Cc: Mikhail Ivanov <ivanov.mikhail1@huawei-partners.com>
Reviewed-by: Günther Noack <gnoack@google.com>
Link: https://lore.kernel.org/r/20241109110856.222842-2-mic@digikod.net
[mic: Slightly improve doc as suggested by Günther]
Signed-off-by: Mickaël Salaün <mic@digikod.net>
|
|
The preferred nodename for fixed-regulators has changed to
pattern: '^regulator(-[0-9]+v[0-9]+|-[0-9a-z-]+)?$'
Fix all Rockchip DT regulator nodenames.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/cfc3cfe1-086b-48f1-9b89-f17c9391d3cc@gmail.com
[Also include the backlight-regulator and panel-regulator from
rk3288-veyron-edp, and adapt the Pinky device accordingly]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Fix spelling of "probability" in tc.yaml documentation. This corrects
the max-P field description in struct tc_sfq_qopt_v1.
Signed-off-by: Abhinav Saxena <xandfury@gmail.com>
Link: https://patch.msgid.link/20241108195642.139315-1-xandfury@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A lockdep report [1] with CONFIG_PROVE_RCU_LIST=y hints
that sctp_v6_available() is calling dev_get_by_index_rcu()
and ipv6_chk_addr() without holding rcu.
[1]
=============================
WARNING: suspicious RCU usage
6.12.0-rc5-virtme #1216 Tainted: G W
-----------------------------
net/core/dev.c:876 RCU-list traversed in non-reader section!!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by sctp_hello/31495:
#0: ffff9f1ebbdb7418 (sk_lock-AF_INET6){+.+.}-{0:0}, at: sctp_bind (./arch/x86/include/asm/jump_label.h:27 net/sctp/socket.c:315) sctp
stack backtrace:
CPU: 7 UID: 0 PID: 31495 Comm: sctp_hello Tainted: G W 6.12.0-rc5-virtme #1216
Tainted: [W]=WARN
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl (lib/dump_stack.c:123)
lockdep_rcu_suspicious (kernel/locking/lockdep.c:6822)
dev_get_by_index_rcu (net/core/dev.c:876 (discriminator 7))
sctp_v6_available (net/sctp/ipv6.c:701) sctp
sctp_do_bind (net/sctp/socket.c:400 (discriminator 1)) sctp
sctp_bind (net/sctp/socket.c:320) sctp
inet6_bind_sk (net/ipv6/af_inet6.c:465)
? security_socket_bind (security/security.c:4581 (discriminator 1))
__sys_bind (net/socket.c:1848 net/socket.c:1869)
? do_user_addr_fault (./include/linux/rcupdate.h:347 ./include/linux/rcupdate.h:880 ./include/linux/mm.h:729 arch/x86/mm/fault.c:1340)
? do_user_addr_fault (./arch/x86/include/asm/preempt.h:84 (discriminator 13) ./include/linux/rcupdate.h:98 (discriminator 13) ./include/linux/rcupdate.h:882 (discriminator 13) ./include/linux/mm.h:729 (discriminator 13) arch/x86/mm/fault.c:1340 (discriminator 13))
__x64_sys_bind (net/socket.c:1877 (discriminator 1) net/socket.c:1875 (discriminator 1) net/socket.c:1875 (discriminator 1))
do_syscall_64 (arch/x86/entry/common.c:52 (discriminator 1) arch/x86/entry/common.c:83 (discriminator 1))
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
RIP: 0033:0x7f59b934a1e7
Code: 44 00 00 48 8b 15 39 8c 0c 00 f7 d8 64 89 02 b8 ff ff ff ff eb bd 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 b8 31 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 09 8c 0c 00 f7 d8 64 89 01 48
All code
========
0: 44 00 00 add %r8b,(%rax)
3: 48 8b 15 39 8c 0c 00 mov 0xc8c39(%rip),%rdx # 0xc8c43
a: f7 d8 neg %eax
c: 64 89 02 mov %eax,%fs:(%rdx)
f: b8 ff ff ff ff mov $0xffffffff,%eax
14: eb bd jmp 0xffffffffffffffd3
16: 66 2e 0f 1f 84 00 00 cs nopw 0x0(%rax,%rax,1)
1d: 00 00 00
20: 0f 1f 00 nopl (%rax)
23: b8 31 00 00 00 mov $0x31,%eax
28: 0f 05 syscall
2a:* 48 3d 01 f0 ff ff cmp $0xfffffffffffff001,%rax <-- trapping instruction
30: 73 01 jae 0x33
32: c3 ret
33: 48 8b 0d 09 8c 0c 00 mov 0xc8c09(%rip),%rcx # 0xc8c43
3a: f7 d8 neg %eax
3c: 64 89 01 mov %eax,%fs:(%rcx)
3f: 48 rex.W
Code starting with the faulting instruction
===========================================
0: 48 3d 01 f0 ff ff cmp $0xfffffffffffff001,%rax
6: 73 01 jae 0x9
8: c3 ret
9: 48 8b 0d 09 8c 0c 00 mov 0xc8c09(%rip),%rcx # 0xc8c19
10: f7 d8 neg %eax
12: 64 89 01 mov %eax,%fs:(%rcx)
15: 48 rex.W
RSP: 002b:00007ffe2d0ad398 EFLAGS: 00000202 ORIG_RAX: 0000000000000031
RAX: ffffffffffffffda RBX: 00007ffe2d0ad3d0 RCX: 00007f59b934a1e7
RDX: 000000000000001c RSI: 00007ffe2d0ad3d0 RDI: 0000000000000005
RBP: 0000000000000005 R08: 1999999999999999 R09: 0000000000000000
R10: 00007f59b9253298 R11: 0000000000000202 R12: 00007ffe2d0ada61
R13: 0000000000000000 R14: 0000562926516dd8 R15: 00007f59b9479000
</TASK>
Fixes: 6fe1e52490a9 ("sctp: check ipv6 addr with sk_bound_dev if set")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Xin Long <lucien.xin@gmail.com>
Link: https://patch.msgid.link/20241107192021.2579789-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix typos:
- syncronized -> synchronized
- interfacs -> interface
- otherwhise -> otherwise
- ony -> only
- busses -> buses
- maxinum -> maximum
Via codespell.
Reported-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andrew Kreimer <algonell@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241106112513.9559-1-algonell@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|