summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2011-02-08FIX: md: process hangs at wait_barrier after 0->10 takeoverKrzysztof Wojcik
Following symptoms were observed: 1. After raid0->raid10 takeover operation we have array with 2 missing disks. When we add disk for rebuild, recovery process starts as expected but it does not finish- it stops at about 90%, md126_resync process hangs in "D" state. 2. Similar behavior is when we have mounted raid0 array and we execute takeover to raid10. After this when we try to unmount array- it causes process umount hangs in "D" In scenarios above processes hang at the same function- wait_barrier in raid10.c. Process waits in macro "wait_event_lock_irq" until the "!conf->barrier" condition will be true. In scenarios above it never happens. Reason was that at the end of level_store, after calling pers->run, we call mddev_resume. This calls pers->quiesce(mddev, 0) with RAID10, that calls lower_barrier. However raise_barrier hadn't been called on that 'conf' yet, so conf->barrier becomes negative, which is bad. This patch introduces setting conf->barrier=1 after takeover operation. It prevents to become barrier negative after call lower_barrier(). Signed-off-by: Krzysztof Wojcik <krzysztof.wojcik@intel.com> Signed-off-by: NeilBrown <neilb@suse.de>
2011-02-07Linux 2.6.38-rc4v2.6.38-rc4Linus Torvalds
2011-02-08batman-adv: Linearize fragment packets before mergeSven Eckelmann
We access the data inside the skbs of two fragments directly using memmove during the merge. The data of the skb could span over multiple skb pages. An direct access without knowledge about the pages would lead to an invalid memory access. Signed-off-by: Sven Eckelmann <sven@narfation.org> [lindner_marek@yahoo.de: Move return from function to the end] Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
2011-02-07Merge master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* master.kernel.org:/home/rmk/linux-2.6-arm: ALSA: AACI: allow writes to MAINCR to take effect ARM: Update mach-types ARM: 6652/1: ep93xx: correct the end address of the AC97 memory resource ARM: mxs/imx28: remove now unused clock lookup "fec.0" ARM: mxs: fix clock base address missing ARM: mxs: acknowledge gpio irq ARM: mach-imx/mach-mx25_3ds: Fix section type ARM: imx: Add VPR200 and MX51_3DS entries to uncompress.h ARM i.MX23: use correct register for setting the rate ARM i.MX23/28: remove secondary field from struct clk. It's unused ARM i.MX28: use correct register for setting the rate ARM i.MX28: fix bit operation
2011-02-08md_make_request: don't touch the bio after calling make_requestChris Mason
md_make_request was calling bio_sectors() for part_stat_add after it was calling the make_request function. This is bad because the make_request function can free the bio and because the bi_size field can change around. The fix here was suggested by Jens Axboe. It saves the sector count before the make_request call. I hit this with CONFIG_DEBUG_PAGEALLOC turned on while trying to break his pretty fusionio card. Cc: <stable@kernel.org> Signed-off-by: Chris Mason <chris.mason@oracle.com> Signed-off-by: NeilBrown <neilb@suse.de>
2011-02-07Merge git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstableLinus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: (33 commits) Btrfs: Fix page count calculation btrfs: Drop __exit attribute on btrfs_exit_compress btrfs: cleanup error handling in btrfs_unlink_inode() Btrfs: exclude super blocks when we read in block groups Btrfs: make sure search_bitmap finds something in remove_from_bitmap btrfs: fix return value check of btrfs_start_transaction() btrfs: checking NULL or not in some functions Btrfs: avoid uninit variable warnings in ordered-data.c Btrfs: catch errors from btrfs_sync_log Btrfs: make shrink_delalloc a little friendlier Btrfs: handle no memory properly in prepare_pages Btrfs: do error checking in btrfs_del_csums Btrfs: use the global block reserve if we cannot reserve space Btrfs: do not release more reserved bytes to the global_block_rsv than we need Btrfs: fix check_path_shared so it returns the right value btrfs: check return value of btrfs_start_ioctl_transaction() properly btrfs: fix return value check of btrfs_join_transaction() fs/btrfs/inode.c: Add missing IS_ERR test btrfs: fix missing break in switch phrase btrfs: fix several uncheck memory allocations ...
2011-02-07Merge branch 'merge' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc * 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: powerpc: Fix hcall tracepoint recursion powerpc/numa: Fix bug in unmap_cpu_from_node powerpc/numa: Disable VPHN on dedicated processor partitions powerpc/numa: Add length when creating OF properties via VPHN powerpc/numa: Check for all VPHN changes powerpc/numa: Only use active VPHN count fields powerpc/pseries: Remove unnecessary variable initializations in numa.c powerpc/pseries: Fix brace placement in numa.c powerpc/pseries: Fix typo in VPHN comments powerpc: Fix some 6xx/7xxx CPU setup functions powerpc: Pass the right cpu_spec to ->setup_cpu() on 64-bit powerpc/book3e: Protect complex macro args in mmu-book3e.h powerpc: Fix pfn_valid() when memory starts at a non-zero address
2011-02-07Merge branch 'omap-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 * 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: arm: omap4: panda: remove usb_nop_xceiv_register(v1) OMAP1: Fix non-working LCD on OMAP310 OMAP3: Devkit8000: Change lcd power pin omap1: remove duplicated #include arm: mach-omap2: mux: free allocated memory on error exit arm: mach-omap2: board-rm680: fix rm680_vemmc regulator constraints OMAP: PM: SmartReflex: Fix possible null pointer read access OMAP: PM: SmartReflex: Fix possible memory leak arm: mach-omap2: voltage: debugfs: fix memory leak OMAP3: PM: fix save secure RAM to restore MPU power state OMAP: PM: SmartReflex: Add missing IS_ERR test
2011-02-07Merge branch 'x86-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: x86, nx: Mark the ACPI resume trampoline code as +x
2011-02-07CRED: Fix memory and refcount leaks upon security_prepare_creds() failureTetsuo Handa
In prepare_kernel_cred() since 2.6.29, put_cred(new) is called without assigning new->usage when security_prepare_creds() returned an error. As a result, memory for new and refcount for new->{user,group_info,tgcred} are leaked because put_cred(new) won't call __put_cred() unless old->usage == 1. Fix these leaks by assigning new->usage (and new->subscribers which was added in 2.6.32) before calling security_prepare_creds(). Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-02-07CRED: Fix BUG() upon security_cred_alloc_blank() failureTetsuo Handa
In cred_alloc_blank() since 2.6.32, abort_creds(new) is called with new->security == NULL and new->magic == 0 when security_cred_alloc_blank() returns an error. As a result, BUG() will be triggered if SELinux is enabled or CONFIG_DEBUG_CREDENTIALS=y. If CONFIG_DEBUG_CREDENTIALS=y, BUG() is called from __invalid_creds() because cred->magic == 0. Failing that, BUG() is called from selinux_cred_free() because selinux_cred_free() is not expecting cred->security == NULL. This does not affect smack_cred_free(), tomoyo_cred_free() or apparmor_cred_free(). Fix these bugs by (1) Set new->magic before calling security_cred_alloc_blank(). (2) Handle null cred->security in creds_are_invalid() and selinux_cred_free(). Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-02-07Merge git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6: cifs: remove checks for ses->status == CifsExiting cifs: add check for kmalloc in parse_dacl cifs: don't send an echo request unless NegProt has been done cifs: enable signing flag in SMB header when server has it on cifs: Possible slab memory corruption while updating extended stats (repost) CIFS: Fix variable types in cifs_iovec_read/write (try #2) cifs: fix length vs. total_read confusion in cifs_demultiplex_thread
2011-02-07platform-drivers: x86: pmic: Use irq_chip buslock mechanismThomas Gleixner
The set_type function of the pmic irq chip is a horrible hack. It schedules work because it cannot access the scu chip from the set_type function. That breaks the assumption, that the type is set after set_type has returned. irq_chips provide buslock functions to avoid the above. Convert the driver to use the proper model. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Feng Tang <feng.tang@intel.com> Cc: Matthew Garrett <mjg@redhat.com> Cc: Alan Cox <alan@linux.intel.com> Cc: Alek Du <alek.du@intel.com> Signed-off-by: Matthew Garrett <mjg@redhat.com>
2011-02-07platform-drivers: x86: Convert pmic to new irq_chip functionsThomas Gleixner
Old functions will go away soon. Remove the stray semicolons while at it. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Feng Tang <feng.tang@intel.com> Cc: Matthew Garrett <mjg@redhat.com> Cc: Alan Cox <alan@linux.intel.com> Cc: Alek Du <alek.du@intel.com> Signed-off-by: Matthew Garrett <mjg@redhat.com>
2011-02-07platform-drivers: x86: pmic: Fix up bogus irq hackeryThomas Gleixner
commit 456dc301([PATCH] intel_pmic_gpio: modify EOI handling following change of kernel irq subsystem) changes - desc->chip->eoi(irq); + + if (desc->chip->irq_eoi) + desc->chip->irq_eoi(irq_get_irq_data(irq)); + else + dev_warn(pg->chip.dev, "missing EOI handler for irq %d\n", irq); With the following explanation: "Latest kernel has many changes in IRQ subsystem and its interfaces, like adding irq_eoi" for struct irq_chip, this patch will make it support both the new and old interface." This is completely bogus. #1) The changelog does not match the patch at all #2) This driver relies on the assumption that it sits behind an eoi capable interrupt line. If the implementation of the underlying chip changes from eoi to irq_eoi then this driver has to follow that change and not add a total bogosity. Remove the sillyness and retrieve the interrupt data from irq_desc directly. No need to got through circles to look it up. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Feng Tang <feng.tang@intel.com> Cc: Matthew Garrett <mjg@redhat.com> Cc: Alan Cox <alan@linux.intel.com> Cc: Alek Du <alek.du@intel.com> Signed-off-by: Matthew Garrett <mjg@redhat.com>
2011-02-07x25: possible skb leak on bad facilitiesandrew hendry
Originally x25_parse_facilities returned -1 for an error 0 meaning 0 length facilities >0 the length of the facilities parsed. 5ef41308f94dc ("x25: Prevent crashing when parsing bad X.25 facilities") introduced more error checking in x25_parse_facilities however used 0 to indicate bad parsing a6331d6f9a429 ("memory corruption in X.25 facilities parsing") followed this further for DTE facilities, again using 0 for bad parsing. The meaning of 0 got confused in the callers. If the facilities are messed up we can't determine where the data starts. So patch makes all parsing errors return -1 and ensures callers close and don't use the skb further. Reported-by: Andy Whitcroft <apw@canonical.com> Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-07mac80211: fix the skb cloned check in the tx pathFelix Fietkau
Using skb_header_cloned to check if it's safe to write to the skb is not enough - mac80211 also touches the tailroom of the skb. Initially this check was only used to increase a counter, however this commit changed the code to also skip skb data reallocation if no extra head/tailroom was needed: commit 4cd06a344db752f513437138953af191cbe9a691 mac80211: skip unnecessary pskb_expand_head calls It added a regression at least with iwl3945, which is fixed by this patch. Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Tested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-07iwlagn: Re-enable RF_KILL interrupt when downDon Fry
With commit 554d1d027b19265c4aa3f718b3126d2b86e09a08 only one RF_KILL interrupt will be seen by the driver when the interface is down. Re-enable the interrupt when it occurs to see all transitions. Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-07ssb-pcmcia: Fix parsing of invariants tuplesMichael Büsch
This fixes parsing of the device invariants (MAC address) for PCMCIA SSB devices. ssb_pcmcia_do_get_invariants expects an iv pointer as data argument. Tested-by: dylan cristiani <d.cristiani@idem-tech.it> Signed-off-by: Michael Buesch <mb@bu3sch.de> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-07Btrfs: Fix page count calculationYan, Zheng
take offset of start position into account when calculating page count. Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
2011-02-07Merge branch 'fixes'Russell King
2011-02-07microblaze: Fix msr instruction detectionMichal Simek
Fix msr instructions detection. The current code just use msrclr for loading msr content and compare it with proper MSR content. If msrclr is not implemented r8 contains pc address. Previous code wanted to use MSR carry bit but if msrclr wasn't implemented carry wasn't cleared. Signed-off-by: Michal Simek <monstr@monstr.eu>
2011-02-07microblaze: Fix pte_update functionMichal Simek
Do not disable irq in asm but use irq macros. Systems with MSR=0 couldn't use pte_update function because msrclr was hardcoded. Signed-off-by: Michal Simek <monstr@monstr.eu>
2011-02-07microblaze: Fix asm compilation warningMichal Simek
Microblaze ASM doesn't support hex values for mfs instructions. /tmp/ccwiXVmt.s: Assembler messages: /tmp/ccwiXVmt.s:19: Warning: ignoring operands: x00 Signed-off-by: Michal Simek <monstr@monstr.eu>
2011-02-07microblaze: Fix IRQ flag handling for MSR=0Michal Simek
Patch: Fix IRQ flag handling naming (sha1: f9ee29270c11dba7d0fe0b83ce47a4d8e8d2101) introduced problem on system with MSR=0. Signed-off-by: Michal Simek <monstr@monstr.eu>
2011-02-07mach-omap2: smartreflex: world-writable debugfs voltage filesVasiliy Kulikov
Don't allow everybody to change voltage settings. Signed-off-by: Vasiliy Kulikov <segoon@openwall.com> Acked-by: Kevin Hilman <khilman@ti.com> Acked-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-02-07ext4: Fix data corruption with multi-block writepages supportCurt Wohlgemuth
This fixes a corruption problem with the multi-block writepages submittal change for ext4, from commit bd2d0210cf22f2bd0cef72eb97cf94fc7d31d8cc ("ext4: use bio layer instead of buffer layer in mpage_da_submit_io"). (Note that this corruption is not present in 2.6.37 on ext4, because the corruption was detected after the feature was merged in 2.6.37-rc1, and so it was turned off by adding a non-default mount option, mblk_io_submit. With this commit, which hopefully fixes the last of the bugs with this feature, we'll be able to turn on this performance feature by default in 2.6.38, and remove the mblk_io_submit option.) The ext4 code path to bundle multiple pages for writeback in ext4_bio_write_page() had a bug: we should be clearing buffer head dirty flags *before* we submit the bio, not in the completion routine. The patch below was tested on 2.6.37 under KVM with the postgresql script which was submitted by Jon Nelson as documented in commit 1449032be1. Without the patch, I'd hit the corruption problem about 50-70% of the time. With the patch, I executed the script > 100 times with no corruption seen. I also fixed a bug to make sure ext4_end_bio() doesn't dereference the bio after the bio_put() call. Reported-by: Jon Nelson <jnelson@jamponi.net> Reported-by: Matthias Bayer <jackdachef@gmail.com> Signed-off-by: Curt Wohlgemuth <curtw@google.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Cc: stable@kernel.org
2011-02-07cifs: remove checks for ses->status == CifsExitingJeff Layton
ses->status is never set to CifsExiting, so these checks are always false. Tested-by: JG <jg@cms.ac> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
2011-02-07Merge branch 'for-rmk' of git://git.pengutronix.de/git/imx/linux-2.6 into fixesRussell King
2011-02-07ALSA: AACI: allow writes to MAINCR to take effectRussell King
The AACI TRM requires the MAINCR enable bit to be held zero for two bitclk cycles plus three apb_pclk cycles. Use a delay of 1us to ensure this. Ensure that writes to MAINCR to change the addressed codec only happen when required, and that they take effect in a similar manner to the above, otherwise we seem to occasionally have stuck slot busy bits. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-02-07perf probe: Add bitfield member supportMasami Hiramatsu
Add bitfield member accessing support to probe arguments. Suggested-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Cc: 2nddept-manager@sdl.hitachi.co.jp Cc: Ingo Molnar <mingo@elte.hu> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Cc: Steven Rostedt <rostedt@goodmis.org> LKML-Reference: <20110204125211.9507.60265.stgit@ltc236.sdl.hitachi.co.jp> Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> [ committer note: Fixed up '%lu' use for return of BYTES_TO_BITS ('%zd') ] Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2011-02-07perf annotate: Fix build errorBorislav Petkov
A small fix for when NO_NEWT_SUPPORT is defined. Add a missing "struct" to the function prototype. Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Mike Galbraith <efault@gmx.de> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tom Zanussi <tzanussi@gmail.com> LKML-Reference: <20110207143218.GA31197@kryptos.osrc.amd.com> Signed-off-by: Borislav Petkov <borislav.petkov@amd.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2011-02-07perf tool: Fix gcc 4.6.0 issuesKyle McMartin
GCC 4.6.0 in Fedora rawhide turned up some compile errors in tools/perf due to the -Werror=unused-but-set-variable flag. I've gone through and annotated some of the assignments that had side effects (ie: return value from a function) with the __used annotation, and in some cases, just removed unused code. In a few cases, we were assigning something useful, but not using it in later parts of the function. kyle@dreadnought:~/src% gcc --version gcc (GCC) 4.6.0 20110122 (Red Hat 4.6.0-0.3) Cc: Ingo Molnar <mingo@redhat.com> LKML-Reference: <20110124161304.GK27353@bombadil.infradead.org> Signed-off-by: Kyle McMartin <kyle@redhat.com> [ committer note: Fixed up the annotation fixes, as that code moved recently ] Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2011-02-07ALSA: hda - switch lfe with side in mixer for 4930gŁukasz Wojniłowicz
Built-in sub-woofer can now be controlled by lfe slider instead of side slider on Acer Aspire 5930g Signed-off-by: Łukasz Wojniłowicz <lukasz.wojnilowicz@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-02-07tracing/kprobes: Add bitfield typeMasami Hiramatsu
Add bitfield type for tracing arguments on kprobe-tracer. The syntax of a bitfield type is: b<bit-size>@<bit-offset>/<container-size> e.g. Accessing 2 bits-width field with 4 bits-offset in 32 bits-width data at 4 bytes offseted from the address pointed by AX register: +4(%ax):b2@4/32 Since the width of container data depends on the arch, so I just added the container-size at the end. Cc: 2nddept-manager@sdl.hitachi.co.jp Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Cc: Steven Rostedt <rostedt@goodmis.org> LKML-Reference: <20110204125205.9507.11363.stgit@ltc236.sdl.hitachi.co.jp> Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2011-02-07tracing/kprobes: Support longer (>128 bytes) commandMasami Hiramatsu
Expand command line buffer of kprobe-tracer to 4096 bytes. Reported-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Cc: 2nddept-manager@sdl.hitachi.co.jp Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Cc: Steven Rostedt <rostedt@goodmis.org> LKML-Reference: <20110204125159.9507.20895.stgit@ltc236.sdl.hitachi.co.jp> Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2011-02-07tracing/kprobes: Cleanup strict_strtol() using codeMasami Hiramatsu
Since strict_strtol() accepts minus digits started with '-', it doesn't need to invert after converting. Cc: 2nddept-manager@sdl.hitachi.co.jp Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Cc: Steven Rostedt <rostedt@goodmis.org> LKML-Reference: <20110204125153.9507.49335.stgit@ltc236.sdl.hitachi.co.jp> Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2011-02-07perf probe: Rewrite find_lazy_match_lines() by using getline(3)Franck Bui-Huu
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: lkml <linux-kernel@vger.kernel.org> LKML-Reference: <m3d3o185u1.fsf@gmail.com> Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2011-02-07perf top: Use pid_t for target_{pid|tid}Denis Kirjanov
Use pid_t data type for target_{pid|tid} vars. Cc: Ingo Molnar <mingo@elte.hu> LKML-Reference: <20110205203938.GA15328@hera.kernel.org> Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org> [ committer note: those variables are now in struct perf_top, fixed ] Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2011-02-07perf tools: Makefile: Use $(QUIET_GEN) for perf.soMichael Witten
So that we get this: CC /home/acme/git/build/perf/bench/mem-memcpy-x86-64-asm.o GEN perf-archive * GEN /home/acme/git/build/perf/python/perf.so CC /home/acme/git/build/perf/builtin-annotate.o Instead of silently building the python binding. LKML-Reference: <1296890359-22659-1-git-send-email-mfwitten@gmail.com> Signed-off-by: Michael Witten <mfwitten@gmail.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2011-02-07crypto: sha-s390 - Reset index after processing partial blockHerbert Xu
The partial block handling in sha-s390 is broken when we get a partial block that is followed by an update which fills it with bytes left-over. Instead of storing the newly left-over bytes at the start of the buffer, it will be stored immediately after the previous partial block. This patch fixes this by resetting the index pointer. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2011-02-07ARM: Update mach-typesRussell King
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-02-07x86, nx: Mark the ACPI resume trampoline code as +xH. Peter Anvin
We reserve lowmem for the things that need it, like the ACPI wakeup code, way early to guarantee availability. This happens before we set up the proper pagetables, so set_memory_x() has no effect. Until we have a better solution, use an initcall to mark the wakeup code executable. Originally-by: Matthieu Castet <castet.matthieu@free.fr> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: Matthias Hopf <mhopf@suse.de> Cc: rjw@sisk.pl Cc: Suresh Siddha <suresh.b.siddha@intel.com> LKML-Reference: <4D4F8019.2090104@zytor.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2011-02-07Merge branch 'perf/core' of ↵Ingo Molnar
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux-2.6 into perf/core
2011-02-07Merge branch 'linus' into perf/coreIngo Molnar
Merge reason: Pick up perf fixes that are now upstream Signed-off-by: Ingo Molnar <mingo@elte.hu>
2011-02-07powerpc: Fix hcall tracepoint recursionAnton Blanchard
Spinlocks on shared processor partitions use H_YIELD to notify the hypervisor we are waiting on another virtual CPU. Unfortunately this means the hcall tracepoints can recurse. The patch below adds a percpu depth and checks it on both the entry and exit hcall tracepoints. Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> CC: stable@kernel.org
2011-02-07powerpc/numa: Fix bug in unmap_cpu_from_nodeAnton Blanchard
When converting to the new cpumask code I screwed up: - if (cpu_isset(cpu, numa_cpumask_lookup_table[node])) { - cpu_clear(cpu, numa_cpumask_lookup_table[node]); + if (cpumask_test_cpu(cpu, node_to_cpumask_map[node])) { + cpumask_set_cpu(cpu, node_to_cpumask_map[node]); This was introduced in commit 25863de07af9 (powerpc/cpumask: Convert NUMA code to new cpumask API) Fix it. Signed-off-by: Anton Blanchard <anton@samba.org> Cc: <stable@kernel.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-02-07powerpc/numa: Disable VPHN on dedicated processor partitionsAnton Blanchard
There is no need to start up the timer and monitor topology changes on a dedicated processor partition, so disable it. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-02-07powerpc/numa: Add length when creating OF properties via VPHNAnton Blanchard
The rest of the NUMA code expects an OF associativity property with the first cell containing the length. Without this fix all topology changes cause us to misparse the property and put the cpu into node 0. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-02-07powerpc/numa: Check for all VPHN changesAnton Blanchard
The hypervisor uses unsigned 1 byte counters to signal topology changes to the OS. Since they can wrap we need to check for any difference, not just if the hypervisor count is greater than the previous count. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
generated by cgit (git 2.34.1) at 2025-09-13 18:33:39 +0000