| Age | Commit message (Collapse) | Author |
|---|
|
to fix XFS performance regression
The following XFS commit:
8ab39f11d974 ("xfs: prevent CIL push holdoff in log recovery")
changed the logic from using bound workqueues to using unbound
workqueues. Functionally this makes sense but it was observed at the
time that the dbench performance dropped quite a lot and CPU migrations
were increased.
The current pattern of the task migration is straight-forward. With XFS,
an IO issuer delegates work to xlog_cil_push_work ()on an unbound kworker.
This runs on a nearby CPU and on completion, dbench wakes up on its old CPU
as it is still idle and no migration occurs. dbench then queues the real
IO on the blk_mq_requeue_work() work item which runs on a bound kworker
which is forced to run on the same CPU as dbench. When IO completes,
the bound kworker wakes dbench but as the kworker is a bound but,
real task, the CPU is not considered idle and dbench gets migrated by
select_idle_sibling() to a new CPU. dbench may ping-pong between two CPUs
for a while but ultimately it starts a round-robin of all CPUs sharing
the same LLC. High-frequency migration on each IO completion has poor
performance overall. It has negative implications both in commication
costs and power management. mpstat confirmed that at low thread counts
that all CPUs sharing an LLC has low level of activity.
Note that even if the CIL patch was reverted, there still would
be migrations but the impact is less noticeable. It turns out that
individually the scheduler, XFS, blk-mq and workqueues all made sensible
decisions but in combination, the overall effect was sub-optimal.
This patch special cases the IO issue/completion pattern and allows
a bound kworker waker and a task wakee to stack on the same CPU if
there is a strong chance they are directly related. The expectation
is that the kworker is likely going back to sleep shortly. This is not
guaranteed as the IO could be queued asynchronously but there is a very
strong relationship between the task and kworker in this case that would
justify stacking on the same CPU instead of migrating. There should be
few concerns about kworker starvation given that the special casing is
only when the kworker is the waker.
DBench on XFS
MMTests config: io-dbench4-async modified to run on a fresh XFS filesystem
UMA machine with 8 cores sharing LLC
5.5.0-rc7 5.5.0-rc7
tipsched-20200124 kworkerstack
Amean 1 22.63 ( 0.00%) 20.54 * 9.23%*
Amean 2 25.56 ( 0.00%) 23.40 * 8.44%*
Amean 4 28.63 ( 0.00%) 27.85 * 2.70%*
Amean 8 37.66 ( 0.00%) 37.68 ( -0.05%)
Amean 64 469.47 ( 0.00%) 468.26 ( 0.26%)
Stddev 1 1.00 ( 0.00%) 0.72 ( 28.12%)
Stddev 2 1.62 ( 0.00%) 1.97 ( -21.54%)
Stddev 4 2.53 ( 0.00%) 3.58 ( -41.19%)
Stddev 8 5.30 ( 0.00%) 5.20 ( 1.92%)
Stddev 64 86.36 ( 0.00%) 94.53 ( -9.46%)
NUMA machine, 48 CPUs total, 24 CPUs share cache
5.5.0-rc7 5.5.0-rc7
tipsched-20200124 kworkerstack-v1r2
Amean 1 58.69 ( 0.00%) 30.21 * 48.53%*
Amean 2 60.90 ( 0.00%) 35.29 * 42.05%*
Amean 4 66.77 ( 0.00%) 46.55 * 30.28%*
Amean 8 81.41 ( 0.00%) 68.46 * 15.91%*
Amean 16 113.29 ( 0.00%) 107.79 * 4.85%*
Amean 32 199.10 ( 0.00%) 198.22 * 0.44%*
Amean 64 478.99 ( 0.00%) 477.06 * 0.40%*
Amean 128 1345.26 ( 0.00%) 1372.64 * -2.04%*
Stddev 1 2.64 ( 0.00%) 4.17 ( -58.08%)
Stddev 2 4.35 ( 0.00%) 5.38 ( -23.73%)
Stddev 4 6.77 ( 0.00%) 6.56 ( 3.00%)
Stddev 8 11.61 ( 0.00%) 10.91 ( 6.04%)
Stddev 16 18.63 ( 0.00%) 19.19 ( -3.01%)
Stddev 32 38.71 ( 0.00%) 38.30 ( 1.06%)
Stddev 64 100.28 ( 0.00%) 91.24 ( 9.02%)
Stddev 128 186.87 ( 0.00%) 160.34 ( 14.20%)
Dbench has been modified to report the time to complete a single "load
file". This is a more meaningful metric for dbench that a throughput
metric as the benchmark makes many different system calls that are not
throughput-related
Patch shows a 9.23% and 48.53% reduction in the time to process a load
file with the difference partially explained by the number of CPUs sharing
a LLC. In a separate run, task migrations were almost eliminated by the
patch for low client counts. In case people have issue with the metric
used for the benchmark, this is a comparison of the throughputs as
reported by dbench on the NUMA machine.
dbench4 Throughput (misleading but traditional)
5.5.0-rc7 5.5.0-rc7
tipsched-20200124 kworkerstack-v1r2
Hmean 1 321.41 ( 0.00%) 617.82 * 92.22%*
Hmean 2 622.87 ( 0.00%) 1066.80 * 71.27%*
Hmean 4 1134.56 ( 0.00%) 1623.74 * 43.12%*
Hmean 8 1869.96 ( 0.00%) 2212.67 * 18.33%*
Hmean 16 2673.11 ( 0.00%) 2806.13 * 4.98%*
Hmean 32 3032.74 ( 0.00%) 3039.54 ( 0.22%)
Hmean 64 2514.25 ( 0.00%) 2498.96 * -0.61%*
Hmean 128 1778.49 ( 0.00%) 1746.05 * -1.82%*
Note that this is somewhat specific to XFS and ext4 shows no performance
difference as it does not rely on kworkers in the same way. No major
problem was observed running other workloads on different machines although
not all tests have completed yet.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200128154006.GD3466@techsingularity.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Fix the 'manged' typo with 'managed' in the drm_panel_bridge_add
kernel-doc documentation.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218121223.30181-1-enric.balletbo@collabora.com
|
|
Sometime the post_disable function is missing (not registered).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1579602296-7683-1-git-send-email-yannick.fertre@st.com
|
|
Remove unnecessary argument when setting PIN_CONFIG_BIAS_DISABLE. No
argument is expected by pinctrl, so removing it should be harmless.
Fixes: 2148ad7790ea ("gpiolib: add support for disabling line bias")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
They are defined in gpio/driver.h now.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Run parse-maintainers.pl and choose GPIO records. Fix them accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Commit d90f36851d65 ("gpiolib: have a single place of calling
set_config()") introduced a regression where we don't pass the right
variable as argument to the set_config() callback of gpio driver from
gpio_set_config(). After reverting two additional patches that came
on top of it - this addresses the issue by changing the type of the last
argument of gpio_do_set_config() to unsigned long and making sure the
packed config variable is actually used in gpio_set_config().
Fixes: d90f36851d65 ("gpiolib: have a single place of calling set_config()")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
|
|
This reverts commit e5e42ad224a040f93bf112e96f82b3a0ed97ffab.
This patch came on top of another patch that introduced a regression.
Revert it before addressing the culprit.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
|
|
This reverts commit d18fddff061d2796525e6d4a958cb3d30aed8efd.
This patch came on top of another patch that introduced a regression.
Revert it before addressing the culprit.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
|
|
To enable HDMI audio the SND_SOC_HDMI_CODEC needs to be
configured. Enable HDMI audio by selecting SND_SOC_HDMI_CODEC if
SND_SOC is configured. SND_SOC_HDMI_CODEC has no config menu entry and
should be selected automatically by the drivers using it.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[narmstrong: atomatically -> automatically]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191129152342.29145-1-jsarha@ti.com
|
|
Add basic support for the Toshiba TC358768 RGB to DSI bridge.
Not all the features of the TC358768 is implemented by the initial driver:
MIPI_DSI_MODE_VIDEO and MIPI_DSI_FMT_RGB888 is only supported and tested.
Only write is implemented for mipi_dsi_host_ops.transfer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200131111553.472-3-peter.ujfalusi@ti.com
|
|
TC358768/TC358778 is a Parallel RGB to MIPI DSI bridge.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200131111553.472-2-peter.ujfalusi@ti.com
|
|
ADV7535 is a part compatible with ADV7533 but it supports 1080p@60hz and
v1p2 supply is fixed to 1.8V
Signed-off-by: Bogdan Togorean <bogdan.togorean@analog.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200121082719.27972-4-bogdan.togorean@analog.com
|
|
ADV7535 is a DSI to HDMI bridge chip like ADV7533 but it allows
1080p@60Hz. v1p2 is fixed to 1.8V on ADV7535.
Signed-off-by: Bogdan Togorean <bogdan.togorean@analog.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200121082719.27972-3-bogdan.togorean@analog.com
|
|
This commit remove DRM_I2C_ADV7533 resulting a simpler driver and less
choices in Kconfig.
Signed-off-by: Bogdan Togorean <bogdan.togorean@analog.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200121082719.27972-2-bogdan.togorean@analog.com
|
|
In commit 9546a0b7ce00 ("tipc: fix wrong connect() return code"), we
fixed the issue with the 'connect()' that returns zero even though the
connecting has failed by waiting for the connection to be 'ESTABLISHED'
really. However, the approach has one drawback in conjunction with our
'lightweight' connection setup mechanism that the following scenario
can happen:
(server) (client)
+- accept()| | wait_for_conn()
| | |connect() -------+
| |<-------[SYN]---------| > sleeping
| | *CONNECTING |
|--------->*ESTABLISHED | |
|--------[ACK]-------->*ESTABLISHED > wakeup()
send()|--------[DATA]------->|\ > wakeup()
send()|--------[DATA]------->| | > wakeup()
. . . . |-> recvq .
. . . . | .
send()|--------[DATA]------->|/ > wakeup()
close()|--------[FIN]-------->*DISCONNECTING |
*DISCONNECTING | |
| ~~~~~~~~~~~~~~~~~~> schedule()
| wait again
.
.
| ETIMEDOUT
Upon the receipt of the server 'ACK', the client becomes 'ESTABLISHED'
and the 'wait_for_conn()' process is woken up but not run. Meanwhile,
the server starts to send a number of data following by a 'close()'
shortly without waiting any response from the client, which then forces
the client socket to be 'DISCONNECTING' immediately. When the wait
process is switched to be running, it continues to wait until the timer
expires because of the unexpected socket state. The client 'connect()'
will finally get ‘-ETIMEDOUT’ and force to release the socket whereas
there remains the messages in its receive queue.
Obviously the issue would not happen if the server had some delay prior
to its 'close()' (or the number of 'DATA' messages is large enough),
but any kind of delay would make the connection setup/shutdown "heavy".
We solve this by simply allowing the 'connect()' returns zero in this
particular case. The socket is already 'DISCONNECTING', so any further
write will get '-EPIPE' but the socket is still able to read the
messages existing in its receive queue.
Note: This solution doesn't break the previous one as it deals with a
different situation that the socket state is 'DISCONNECTING' but has no
error (i.e. sk->sk_err = 0).
Fixes: 9546a0b7ce00 ("tipc: fix wrong connect() return code")
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following sparse warning:
net/mptcp/protocol.c:646:13: warning: symbol 'mptcp_sk_clone_lock' was not declared. Should it be static?
Fixes: b0519de8b3f1 ("mptcp: fix use-after-free for ipv6")
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following sparse warning:
net/tipc/node.c:281:6: warning: symbol 'tipc_node_free' was not declared. Should it be static?
net/tipc/node.c:2801:5: warning: symbol '__tipc_nl_node_set_key' was not declared. Should it be static?
net/tipc/node.c:2878:5: warning: symbol '__tipc_nl_node_flush_key' was not declared. Should it be static?
Fixes: fc1b6d6de220 ("tipc: introduce TIPC encryption & authentication")
Fixes: e1f32190cf7d ("tipc: add support for AEAD key setting via netlink")
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Atomic modesetting doesn't use struct drm_connector_funcs.dpms and
the set function, drm_helper_connector_dpms(), wouldn't support it
anyway. So keep the pointer to NULL.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200207141602.4760-2-tzimmermann@suse.de
|
|
Atomic modesetting doesn't use struct drm_connector_funcs.dpms and
the set function, drm_helper_connector_dpms(), wouldn't support it
anyway. So keep the pointer to NULL.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200207141602.4760-1-tzimmermann@suse.de
|
|
Now, Allwiner MIPI-DSI support is available for ARM64
Allwinner SoC like A64. So, let's build it as a module.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Many sunxi based board needs CONFIG_SUN8I_THERMAL for thermal support.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Many sunxi based board needs CONFIG_SUN8I_THERMAL for thermal support.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
With the introduction of 738987a1d6f1 ("mmc: bcm2835: Use
dma_request_chan() instead dma_request_slave_channel()") sdhost-bcm2835
now waits for its DMA channel to be available when defined in the
device-tree (it would previously default to PIO). Albeit the right
behaviour, the MMC host is needed for booting. So this makes sure the
DMA channel shows up in time.
Fixes: 738987a1d6f1 ("mmc: bcm2835: Use dma_request_chan() instead dma_request_slave_channel()")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Change 21537dc driver PMBus polling of MFR_COMMON from bits 5/4 to
bits 6/5. This fixs a LTC297X family bug where polling always returns
not busy even when the part is busy. This fixes a LTC388X and
LTM467X bug where polling used PEND and NOT_IN_TRANS, and BUSY was
not polled, which can lead to NACKing of commands. LTC388X and
LTM467X modules now poll BUSY and PEND, increasing reliability by
eliminating NACKing of commands.
Signed-off-by: Mike Jones <michael-a1.jones@analog.com>
Link: https://lore.kernel.org/r/1580234400-2829-2-git-send-email-michael-a1.jones@analog.com
Fixes: e04d1ce9bbb49 ("hwmon: (ltc2978) Add polling for chips requiring it")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
When the lock was introduced in commit 72aabfb862e40 ("drm/i915/gvt: Add mutual
lock for ppgtt mm LRU list") one place got lost.
Fixes: 72aabfb862e4 ("drm/i915/gvt: Add mutual lock for ppgtt mm LRU list")
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1580742421-25194-1-git-send-email-igor.druzhinin@citrix.com
|
|
If the module happens to be loaded later at runtime there is a chance
memory is already fragmented enough to fail allocation of firmware
blob storage and consequently GVT init. Since it doesn't seem to be
necessary to have the blob contiguous, use vmalloc() instead to avoid
the issue.
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1579723824-25711-1-git-send-email-igor.druzhinin@citrix.com
|
|
The spi_register_driver() will set the ->owner member to THIS_MODULE.
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: dri-devel@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200131204923.48928-4-andriy.shevchenko@linux.intel.com
|
|
There is one OF call in the driver that limits its area of use.
Replace it to generic device_get_match_data() and get rid of OF dependency.
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: dri-devel@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: David Lechner <david@lechnology.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200131204923.48928-3-andriy.shevchenko@linux.intel.com
|
|
The spi_register_driver() will set the ->owner member to THIS_MODULE.
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: dri-devel@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: David Lechner <david@lechnology.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200131204923.48928-2-andriy.shevchenko@linux.intel.com
|
|
There is one OF call in the driver that limits its area of use.
Replace it to generic device_get_match_data() and get rid of OF dependency.
While here, cast SPI driver data to certain enumerator type.
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: dri-devel@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: David Lechner <david@lechnology.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200131204923.48928-1-andriy.shevchenko@linux.intel.com
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- fix randconfig to generate a sane .config
- rename hostprogs-y / always to hostprogs / always-y, which are more
natual syntax.
- optimize scripts/kallsyms
- fix yes2modconfig and mod2yesconfig
- make multiple directory targets ('make foo/ bar/') work
* tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: make multiple directory targets work
kconfig: Invalidate all symbols after changing to y or m.
kallsyms: fix type of kallsyms_token_table[]
scripts/kallsyms: change table to store (strcut sym_entry *)
scripts/kallsyms: rename local variables in read_symbol()
kbuild: rename hostprogs-y/always to hostprogs/always-y
kbuild: fix the document to use extra-y for vmlinux.lds
kconfig: fix broken dependency in randconfig-generated .config
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs
Pull new zonefs file system from Damien Le Moal:
"Zonefs is a very simple file system exposing each zone of a zoned
block device as a file.
Unlike a regular file system with native zoned block device support
(e.g. f2fs or the on-going btrfs effort), zonefs does not hide the
sequential write constraint of zoned block devices to the user. As a
result, zonefs is not a POSIX compliant file system. Its goal is to
simplify the implementation of zoned block devices support in
applications by replacing raw block device file accesses with a richer
file based API, avoiding relying on direct block device file ioctls
which may be more obscure to developers.
One example of this approach is the implementation of LSM
(log-structured merge) tree structures (such as used in RocksDB and
LevelDB) on zoned block devices by allowing SSTables to be stored in a
zone file similarly to a regular file system rather than as a range of
sectors of a zoned device. The introduction of the higher level
construct "one file is one zone" can help reducing the amount of
changes needed in the application while at the same time allowing the
use of zoned block devices with various programming languages other
than C.
Zonefs IO management implementation uses the new iomap generic code.
Zonefs has been successfully tested using a functional test suite
(available with zonefs userland format tool on github) and a prototype
implementation of LevelDB on top of zonefs"
* tag 'zonefs-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
zonefs: Add documentation
fs: New zonefs file system
|
|
In order to allow the GICv4 code to link properly on 32bit ARM,
make sure we don't use 64bit divisions when it isn't strictly
necessary.
Fixes: 4e6437f12d6e ("irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull cifs fixes from Steve French:
"13 cifs/smb3 patches, most from testing at the SMB3 plugfest this week:
- Important fix for multichannel and for modefromsid mounts.
- Two reconnect fixes
- Addition of SMB3 change notify support
- Backup tools fix
- A few additional minor debug improvements (tracepoints and
additional logging found useful during testing this week)"
* tag '5.6-rc-smb3-plugfest-patches' of git://git.samba.org/sfrench/cifs-2.6:
smb3: Add defines for new information level, FileIdInformation
smb3: print warning once if posix context returned on open
smb3: add one more dynamic tracepoint missing from strict fsync path
cifs: fix mode bits from dir listing when mounted with modefromsid
cifs: fix channel signing
cifs: add SMB3 change notification support
cifs: make multichannel warning more visible
cifs: fix soft mounts hanging in the reconnect code
cifs: Add tracepoints for errors on flush or fsync
cifs: log warning message (once) if out of disk space
cifs: fail i/o on soft mounts if sessionsetup errors out
smb3: fix problem with null cifs super block with previous patch
SMB3: Backup intent flag missing from some more ops
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vboxfs from Al Viro:
"This is the VirtualBox guest shared folder support by Hans de Goede,
with fixups for fs_parse folded in to avoid bisection hazards from
those API changes..."
* 'work.vboxsf' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: Add VirtualBox guest shared folder (vboxsf) support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for X86:
- Ensure that the PIT is set up when the local APIC is disable or
configured in legacy mode. This is caused by an ordering issue
introduced in the recent changes which skip PIT initialization when
the TSC and APIC frequencies are already known.
- Handle malformed SRAT tables during early ACPI parsing which caused
an infinite loop anda boot hang.
- Fix a long standing race in the affinity setting code which affects
PCI devices with non-maskable MSI interrupts. The problem is caused
by the non-atomic writes of the MSI address (destination APIC id)
and data (vector) fields which the device uses to construct the MSI
message. The non-atomic writes are mandated by PCI.
If both fields change and the device raises an interrupt after
writing address and before writing data, then the MSI block
constructs a inconsistent message which causes interrupts to be
lost and subsequent malfunction of the device.
The fix is to redirect the interrupt to the new vector on the
current CPU first and then switch it over to the new target CPU.
This allows to observe an eventually raised interrupt in the
transitional stage (old CPU, new vector) to be observed in the APIC
IRR and retriggered on the new target CPU and the new vector.
The potential spurious interrupts caused by this are harmless and
can in the worst case expose a buggy driver (all handlers have to
be able to deal with spurious interrupts as they can and do happen
for various reasons).
- Add the missing suspend/resume mechanism for the HYPERV hypercall
page which prevents resume hibernation on HYPERV guests. This
change got lost before the merge window.
- Mask the IOAPIC before disabling the local APIC to prevent
potentially stale IOAPIC remote IRR bits which cause stale
interrupt lines after resume"
* tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Mask IOAPIC entries when disabling the local APIC
x86/hyperv: Suspend/resume the hypercall page for hibernation
x86/apic/msi: Plug non-maskable MSI affinity race
x86/boot: Handle malformed SRAT tables during early ACPI parsing
x86/timer: Don't skip PIT setup when APIC is disabled or in legacy mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull SMP fixes from Thomas Gleixner:
"Two fixes for the SMP related functionality:
- Make the UP version of smp_call_function_single() match SMP
semantics when called for a not available CPU. Instead of emitting
a warning and assuming that the function call target is CPU0,
return a proper error code like the SMP version does.
- Remove a superfluous check in smp_call_function_many_cond()"
* tag 'smp-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
smp/up: Make smp_call_function_single() match SMP semantics
smp: Remove superfluous cond_func check in smp_call_function_many_cond()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"A set of fixes and improvements for the perf subsystem:
Kernel fixes:
- Install cgroup events to the correct CPU context to prevent a
potential list double add
- Prevent an integer underflow in the perf mlock accounting
- Add a missing prototype for arch_perf_update_userpage()
Tooling:
- Add a missing unlock in the error path of maps__insert() in perf
maps.
- Fix the build with the latest libbfd
- Fix the perf parser so it does not delete parse event terms, which
caused a regression for using perf with the ARM CoreSight as the
sink configuration was missing due to the deletion.
- Fix the double free in the perf CPU map merging test case
- Add the missing ustring support for the perf probe command"
* tag 'perf-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf maps: Add missing unlock to maps__insert() error case
perf probe: Add ustring support for perf probe command
perf: Make perf able to build with latest libbfd
perf test: Fix test case Merge cpu map
perf parse: Copy string to perf_evsel_config_term
perf parse: Refactor 'struct perf_evsel_config_term'
kernel/events: Add a missing prototype for arch_perf_update_userpage()
perf/cgroups: Install cgroup events to correct cpuctx
perf/core: Fix mlock accounting in perf_mmap()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Two small fixes for the time(r) subsystem:
- Handle a subtle race between the clocksource watchdog and a
concurrent clocksource watchdog stop/start sequence correctly to
prevent a timer double add bug.
- Fix the file path for the core time namespace file"
* tag 'timers-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Prevent double add_timer_on() for watchdog_timer
MAINTAINERS: Correct path to time namespace source file
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull interrupt fixes from Thomas Gleixner:
"A set of fixes for the interrupt subsystem:
- Provision only ACPI enabled redistributors on GICv3
- Use the proper command colums when building the INVALL command for
the GICv3-ITS
- Ensure the allocation of the L2 vPE table for GICv4.1
- Correct the GICv4.1 VPROBASER programming so it uses the proper
size
- A set of small GICv4.1 tidy up patches
- Configuration cleanup for C-SKY interrupt chip
- Clarify the function documentation for irq_set_wake() to document
that the wakeup functionality is orthogonal to the irq
disable/enable mechanism"
* tag 'irq-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Rename VPENDBASER/VPROPBASER accessors
irqchip/gic-v3-its: Remove superfluous WARN_ON
irqchip/gic-v4.1: Drop 'tmp' in inherit_vpe_l1_table_from_rd()
irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level
irqchip/gic-v4.1: Set vpe_l1_base for all redistributors
irqchip/gic-v4.1: Fix programming of GICR_VPROPBASER_4_1_SIZE
genirq: Clarify that irq wake state is orthogonal to enable/disable
irqchip/gic-v3-its: Reference to its_invall_cmd descriptor when building INVALL
irqchip: Some Kconfig cleanup for C-SKY
irqchip/gic-v3: Only provision redistributors that are enabled in ACPI
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fix from Thomas Gleixner:
"A single fix for a EFI boot regression on X86 which was caused by the
recent rework of the EFI memory map parsing. On systems with invalid
memmap entries the cleanup function uses an value which cannot be
relied on in this stage. Use the actual EFI memmap entry instead"
* tag 'efi-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/x86: Fix boot regression on systems with invalid memmap entries
|
|
This adds support fot ilitek,ili9486 based displays with shift register
in front of controller.
Ozzmaker,Piscreen and Waveshare,rpi-lcd-35 are such displays.
Acked-by: Sam Ravnborg <sam@ravnborg.org> (v4)
Reviewed-by: Noralf Tronnes <noralf@tronnes.org> (v4)
Signed-off-by: Kamlesh Gurudasani <kamlesh.gurudasani@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
[fixed checkpatch warnings]
Link: https://patchwork.freedesktop.org/patch/msgid/a9c8065c3ef7707650630b3b21a0c01d725fc5a0.1581270802.git.kamlesh.gurudasani@gmail.com
|
|
This binding is for the tft displays based on ilitek,ili9486.
ozzmaker,piscreen and waveshare,rpi-lcd-35 are such displays
Signed-off-by: Kamlesh Gurudasani <kamlesh.gurudasani@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/8938c7a53598db793bbcddf205dcf35bcc19a18e.1581270802.git.kamlesh.gurudasani@gmail.com
|
|
Jonas reports that he sometimes sees -97/-22 error returns from
sendmsg, if it gets punted async. This is due to not retaining the
sockaddr_storage between calls. Include that in the state we copy when
going async.
Cc: stable@vger.kernel.org # 5.3+
Reported-by: Jonas Bonn <jonas@norrbonn.se>
Tested-by: Jonas Bonn <jonas@norrbonn.se>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Since commit 742379c0c4001 ("drm/i915: Start chopping up the GPU error
capture"), function 'i915_error_state_store' was defined and used with
only one parameter.
But if no 'CONFIG_DRM_I915_CAPTURE_ERROR', this function was defined
with two parameter.
This may lead compile error. This patch fix it.
Fixes: 742379c0c400 ("drm/i915: Start chopping up the GPU error capture")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200117073436.6507-1-zhangxiaoxu5@huawei.com
(cherry picked from commit 04062c58faafddf62006c6f8e5077dc050e8207e)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Normally we cancel all work we track, but for untracked work we could
leave the async worker behind until that work completes. This is totally
fine, but does leave resources pending after the task is gone until that
work completes.
Cancel work that this task queued up when it goes away.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add a helper that allows the caller to cancel work based on what mm
it belongs to. This allows io_uring to cancel work from a given
task or thread when it exits.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We want to use the cancel functionality for canceling based on not
just the work itself. Instead of matching on the work address
manually, allow a match handler to tell us if we found the right work
item or not.
No functional changes in this patch.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
