| Age | Commit message (Collapse) | Author |
|---|
|
Update to the latest definition of the firmware
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
|
|
Add driver implementation for reading the current power from the device
CPU F/W.
Signed-off-by: Sagiv Ozeri <sozeri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
|
|
Improve "vm" debugfs node to print also the virtual addresses which are
currently mapped to HW blocks in the device.
Signed-off-by: Sagiv Ozeri <sozeri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
|
|
For simplicity, use a single bringup flag indicating which FW
binaries should loaded to device.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
|
|
Timeout in wait for interrupt is in 32-bit variable so we need to use
the correct maximum value to compare.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
|
|
In order to support command submissions from user space, the driver
need to add support for user interrupt completions. The driver will
allow multiple user threads to wait for an interrupt and perform
a comparison with a given user address once interrupt expires.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
|
|
In order to support user interrupts, driver must enable all MSI-X
interrupts for any case user will trigger them. We differentiate
between a valid user interrupt and a non valid one.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
|
|
As the F/wW is the first to detect out of sync event, a new event is
added to notify the driver on such event. In which case the driver
performs hard reset.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
|
|
Because our graph contains network operations, we need to account
for delay in the network.
5 seconds timeout per CS is not enough to account for that.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
|
|
Notify to the user that although he closed the FD, the device is
still in use because there are live CS and/or memory mappings (mmaps).
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
|
|
Move the field to correct location in structure and remove comment.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
|
|
After any reset (soft or hard) the device (the engines/QMANs) should
be idle. If they are not idle, fail the reset. If it is soft-reset,
the driver will try to do hard-reset automatically. If it is hard-reset,
the driver will make the device non-operational.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
|
|
The device is actually released only after the refcnt of the hpriv
structure is 0, which means all its contexts were closed.
If we reset the device while a context is still open, there are
possibilities for unexpected behavior and crashes. For example, if the
process has a mapping of a register block that is now currently being
reset, and the process writes/reads to that block during the reset,
the device can get stuck.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
|
|
In order to support command submissions that are done directly from
user space, the driver must perform soft reset once user closes its FD.
In case the soft reset fails or device is not idle, a hard reset should
be performed.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
|
|
currently we support only 2 asids in all asics.
asid 0 for driver, and asic 1 for user.
no need to setup 1024 asids configurations at init phase.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
|
|
https://git.linaro.org/people/daniel.lezcano/linux into timers/core
Pull clocksource/event updates from Daniel Lezcano:
- Add dt bindings for the wpcm450 and the timer declaration (Jonathan
Neuschäfer)
- Add dt bindings for the JZ4760, the timer declaration for the
ingenic ost and timer (Paul Cercueil)
- Add dt bindings for the cmt r8a779a0 (Wolfram Sang)
- Add dt bindings for the cmt r8a77961 (Niklas Söderlund)
- Add missing dt bindings for the tmu r8a7795, r8a7796, r8a77961, r8a77965,
r8a77990 and r8a77995 (Niklas Söderlund)
- Check pending post before writing a new post in register for the
timer TI dm and add the stopped callback ops to prevent any
spurious interrupt (Tony Lindgren)
- Fix return value check at init when calling device_node_to_regmap()
for the Ingenic OST timer (Wei Yongjun)
- Fix a trivial typo s/overflw/overflow/ for the pistachio timer (Drew Fustini)
- Don't use CMTOUT_IE with R-Car Gen2/3 (Wolfram Sang)
- Fix rollback when the initialization fails on the dw_apb timer (Dinh Nguyen)
- Switch to timer TI dm on dra7 in order to prevent using the bogus
architected timer which fails to wrap correctly after 388 days (Tony Lindgren)
- Add function annotation to optimize memory for the ARM architected
timer (Jisheng Zhang)
|
|
In adf_create_ring, if the callee adf_init_ring() failed, the callee will
free the ring->base_addr by dma_free_coherent() and return -EFAULT. Then
adf_create_ring will goto err and the ring->base_addr will be freed again
in adf_cleanup_ring().
My patch sets ring->base_addr to NULL after the first freed to avoid the
double free.
Fixes: a672a9dc872ec ("crypto: qat - Intel(R) QAT transport code")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The "qdma" is a structure variable instead of actual data. This
structure doesn't need to be zerod, The memset is useless and redundant.
So delete it.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
skcipher: Add a verifying to check whether the triple DES key
is weak.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
There are two error return paths that are not freeing rxd and causing
memory leaks. Fix these.
Addresses-Coverity: ("Resource leak")
Fixes: 00c9211f60db ("crypto: sa2ul - Fix DMA mapping API usage")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
It appears there are several failure return paths that don't seem
to be free'ing pad. Fix these.
Addresses-Coverity: ("Resource leak")
Fixes: d9b45418a917 ("crypto: sun8i-ss - support hash algorithms")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Delete unneeded variable initialization
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Tang Yizhou <tangyizhou@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Do a trivial typo fix.
s/discribed/described
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ruiqi Gong <gongruiqi1@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Fix the following whitescan warning:
Assigning value "64" to "dst.address" here, but that stored value is
overwritten before it can be used.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: John Allen <john.allen@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
ctx_q_num is a module parameter set by the user to specify the
number of qp queues required to create a ctx.
When the number of qp queues allocated by PF or VF is less than
the ctx_q_num, an error will be reported when ctx is initialized
in kernel mode, which leads to the problem that the registered
algorithms cannot be used.
Therefore, when PF or VF is initialized, if the number of qp queues
is not enough to create a ctx, the kernel mode cannot be used,
and there is no need to register the kernel mode algorithms.
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Some CONFIG select miss CRYPTO_.
Reported-by: Chen-Yu Tsai <wens@csie.org>
Fixes: 56f6d5aee88d1 ("crypto: sun8i-ce - support hash algorithms")
Fixes: d9b45418a9177 ("crypto: sun8i-ss - support hash algorithms")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Previous kernels allowed the BLKROSET to override the disk's read-only
status. With that situation fixed the pmem driver needs to rely on
notification events to reevaluate the disk read-only status after the
host region has been marked read-write.
Recall that when libnvdimm determines that the persistent memory has
lost persistence (for example lack of energy to flush from DRAM to FLASH
on an NVDIMM-N device) it marks the region read-only, but that state can
be overridden by the user via:
echo 0 > /sys/bus/nd/devices/regionX/read_only
...to date there is no notification that the region has restored
persistence, so the user override is the only recovery.
Fixes: 52f019d43c22 ("block: add a hard-readonly flag to struct gendisk")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Tested-by: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Jens Axboe <axboe@kernel.dk>
Link: https://lore.kernel.org/r/161534060720.528671.2341213328968989192.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
This commit fixes below sparse warnings with W=2 about shadow
declarations:
drivers/bus/mhi/core/main.c: In function ‘parse_xfer_event’:
drivers/bus/mhi/core/main.c:667:17: warning: declaration of ‘flags’ shadows a previous local [-Wshadow]
667 | unsigned long flags;
| ^~~~~
drivers/bus/mhi/core/main.c:565:16: note: shadowed declaration is here
565 | unsigned long flags = 0;
| ^~~~~
drivers/bus/mhi/core/main.c: In function ‘mhi_process_ctrl_ev_ring’:
drivers/bus/mhi/core/main.c:856:23: warning: declaration of ‘new_state’ shadows a previous local [-Wshadow]
856 | enum mhi_pm_state new_state;
| ^~~~~~~~~
drivers/bus/mhi/core/main.c:837:19: note: shadowed declaration is here
837 | enum mhi_state new_state;
| ^~~~~~~~~
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Pull cifs fixes from Steve French:
"Three cifs/smb3 fixes, two for stable: a reconnect fix and a fix for
display of devnames with special characters"
* tag '5.12-rc6-smb3' of git://git.samba.org/sfrench/cifs-2.6:
cifs: escape spaces in share names
fs: cifs: Remove unnecessary struct declaration
cifs: On cifs_reconnect, resolve the hostname again.
|
|
https://gitlab.freedesktop.org/drm/msm into drm-fixes
some more minor fixes:
- a5xx/a6xx timestamp fix
- microcode version check
- fail path fix
- block programming fix
- error removal fix.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGsMj7Nv3vVaVWMxPy8Y=Z_SnZmVKhKgKDxDYTr9rGN_+w@mail.gmail.com
|
|
nlh is being checked for validtity two times when it is dereferenced in
this function. Check for validity again when updating the flags through
nlh pointer to make the dereferencing safe.
CC: <stable@vger.kernel.org>
Addresses-Coverity: ("NULL pointer dereference")
Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Martin Blumenstingl says:
====================
lantiq: GSWIP: two more fixes
after my last patch got accepted and is now in net as commit
3e6fdeb28f4c33 ("net: dsa: lantiq_gswip: Let GSWIP automatically set
the xMII clock") [0] some more people from the OpenWrt community
(many thanks to everyone involved) helped test the GSWIP driver: [1]
It turns out that the previous fix does not work for all boards.
There's no regression, but it doesn't fix as many problems as I
thought. This is why two more fixes are needed:
- the first one solves many (four known but probably there are
a few extra hidden ones) reported bugs with the GSWIP where no
traffic would flow. Not all circumstances are fully understood
but testing shows that switching away from PHY auto polling
solves all of them
- while investigating the different problems which are addressed
by the first patch some small issues with the existing code were
found. These are addressed by the second patch
Changes since v1 at [0]:
- Don't configure the link parameters in gswip_phylink_mac_config
(as we're using the "modern" way in gswip_phylink_mac_link_up).
Thanks to Andrew for the hint with the phylink documentation.
- Clarify that GSWIP_MII_CFG_RMII_CLK is ignored by the hardware in
the description of the second patch as suggested by Hauke
- Don't set GSWIP_MII_CFG_RGMII_IBS in the second patch as we don't
have any hardware available for testing this. The patch
description now also reflects this.
- Added Andrew's Reviewed-by to the first patch (thank you!)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a few more bits in the GSWIP_MII_CFG register for which we
did rely on the boot-loader (or the hardware defaults) to set them up
properly.
For some external RMII PHYs we need to select the GSWIP_MII_CFG_RMII_CLK
bit and also we should un-set it for non-RMII PHYs. The
GSWIP_MII_CFG_RMII_CLK bit is ignored for other PHY connection modes.
The GSWIP IP also supports in-band auto-negotiation for RGMII PHYs when
the GSWIP_MII_CFG_RGMII_IBS bit is set. Clear this bit always as there's
no known hardware which uses this (so it is not tested yet).
Clear the xMII isolation bit when set at initialization time if it was
previously set by the bootloader. Not doing so could lead to no traffic
(neither RX nor TX) on a port with this bit set.
While here, also add the GSWIP_MII_CFG_RESET bit. We don't need to
manage it because this bit is self-clearning when set. We still add it
here to get a better overview of the GSWIP_MII_CFG register.
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable@vger.kernel.org
Suggested-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PHY auto polling on the GSWIP hardware can be used so link changes
(speed, link up/down, etc.) can be detected automatically. Internally
GSWIP reads the PHY's registers for this functionality. Based on this
automatic detection GSWIP can also automatically re-configure it's port
settings. Unfortunately this auto polling (and configuration) mechanism
seems to cause various issues observed by different people on different
devices:
- FritzBox 7360v2: the two Gbit/s ports (connected to the two internal
PHY11G instances) are working fine but the two Fast Ethernet ports
(using an AR8030 RMII PHY) are completely dead (neither RX nor TX are
received). It turns out that the AR8030 PHY sets the BMSR_ESTATEN bit
as well as the ESTATUS_1000_TFULL and ESTATUS_1000_XFULL bits. This
makes the PHY auto polling state machine (rightfully?) think that the
established link speed (when the other side is Gbit/s capable) is
1Gbit/s.
- None of the Ethernet ports on the Zyxel P-2812HNU-F1 (two are
connected to the internal PHY11G GPHYs while the other three are
external RGMII PHYs) are working. Neither RX nor TX traffic was
observed. It is not clear which part of the PHY auto polling state-
machine caused this.
- FritzBox 7412 (only one LAN port which is connected to one of the
internal GPHYs running in PHY22F / Fast Ethernet mode) was seeing
random disconnects (link down events could be seen). Sometimes all
traffic would stop after such disconnect. It is not clear which part
of the PHY auto polling state-machine cauased this.
- TP-Link TD-W9980 (two ports are connected to the internal GPHYs
running in PHY11G / Gbit/s mode, the other two are external RGMII
PHYs) was affected by similar issues as the FritzBox 7412 just without
the "link down" events
Switch to software based configuration instead of PHY auto polling (and
letting the GSWIP hardware configure the ports automatically) for the
following link parameters:
- link up/down
- link speed
- full/half duplex
- flow control (RX / TX pause)
After a big round of manual testing by various people (who helped test
this on OpenWrt) it turns out that this fixes all reported issues.
Additionally it can be considered more future proof because any
"quirk" which is implemented for a PHY on the driver side can now be
used with the GSWIP hardware as well because Linux is in control of the
link parameters.
As a nice side-effect this also solves a problem where fixed-links were
not supported previously because we were relying on the PHY auto polling
mechanism, which cannot work for fixed-links as there's no PHY from
where it can read the registers. Configuring the link settings on the
GSWIP ports means that we now use the settings from device-tree also for
ports with fixed-links.
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Fixes: 3e6fdeb28f4c33 ("net: dsa: lantiq_gswip: Let GSWIP automatically set the xMII clock")
Cc: stable@vger.kernel.org
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull rdma fixes from Jason Gunthorpe:
"Nothing very exciting here, just a few small bug fixes. No red flags
for this release have shown up.
- Regression from the last pull request in cxgb4 related to the ipv6
fixes
- KASAN crasher in rtrs
- oops in hfi1 related to a buggy BIOS
- Userspace could oops qedr's XRC support
- Uninitialized memory when parsing a LS_NLA_TYPE_DGID netlink
message"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/addr: Be strict with gid size
RDMA/qedr: Fix kernel panic when trying to access recv_cq
IB/hfi1: Fix probe time panic when AIP is enabled with a buggy BIOS
RDMA/cxgb4: check for ipv6 address properly while destroying listener
RDMA/rtrs-clt: Close rtrs client conn before destroying rtrs clt session files
|
|
The Devicetree standard specifies an 8 byte alignment of the FDT.
Code in libfdt expects this alignment for an FDT image in memory.
kmemdup() returns 4 byte alignment on openrisc. Replace kmemdup()
with kmalloc(), align pointer, memcpy() to get proper alignment.
The 4 byte alignment exposed a related bug which triggered a crash
on openrisc with:
commit 79edff12060f ("scripts/dtc: Update to upstream version v1.6.0-51-g183df9e9c2b9")
as reported in:
https://lore.kernel.org/lkml/20210327224116.69309-1-linux@roeck-us.net/
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Link: https://lore.kernel.org/r/20210408204508.2276230-1-frowand.list@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Wait until after the UMEM is checked for null to dereference it.
Fixes: 43f1bc1efff1 ("libbpf: Restore umem state after socket create failure")
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210408052009.7844-1-ciara.loftus@intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-04-08
This series contains updates to i40e and ice drivers.
Grzegorz fixes the ordering of parameters to i40e_aq_get_phy_register()
which is causing incorrect information to be reported.
Arkadiusz fixes various sparse issues reported on the i40e driver.
Yongxin Liu fixes a memory leak with aRFS following resume from suspend
for ice driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reproduce:
modprobe sch_teql
tc qdisc add dev teql0 root teql0
This leads to (for instance in Centos 7 VM) OOPS:
[ 532.366633] BUG: unable to handle kernel NULL pointer dereference at 00000000000000a8
[ 532.366733] IP: [<ffffffffc06124a8>] teql_destroy+0x18/0x100 [sch_teql]
[ 532.366825] PGD 80000001376d5067 PUD 137e37067 PMD 0
[ 532.366906] Oops: 0000 [#1] SMP
[ 532.366987] Modules linked in: sch_teql ...
[ 532.367945] CPU: 1 PID: 3026 Comm: tc Kdump: loaded Tainted: G ------------ T 3.10.0-1062.7.1.el7.x86_64 #1
[ 532.368041] Hardware name: Virtuozzo KVM, BIOS 1.11.0-2.vz7.2 04/01/2014
[ 532.368125] task: ffff8b7d37d31070 ti: ffff8b7c9fdbc000 task.ti: ffff8b7c9fdbc000
[ 532.368224] RIP: 0010:[<ffffffffc06124a8>] [<ffffffffc06124a8>] teql_destroy+0x18/0x100 [sch_teql]
[ 532.368320] RSP: 0018:ffff8b7c9fdbf8e0 EFLAGS: 00010286
[ 532.368394] RAX: ffffffffc0612490 RBX: ffff8b7cb1565e00 RCX: ffff8b7d35ba2000
[ 532.368476] RDX: ffff8b7d35ba2000 RSI: 0000000000000000 RDI: ffff8b7cb1565e00
[ 532.368557] RBP: ffff8b7c9fdbf8f8 R08: ffff8b7d3fd1f140 R09: ffff8b7d3b001600
[ 532.368638] R10: ffff8b7d3b001600 R11: ffffffff84c7d65b R12: 00000000ffffffd8
[ 532.368719] R13: 0000000000008000 R14: ffff8b7d35ba2000 R15: ffff8b7c9fdbf9a8
[ 532.368800] FS: 00007f6a4e872740(0000) GS:ffff8b7d3fd00000(0000) knlGS:0000000000000000
[ 532.368885] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 532.368961] CR2: 00000000000000a8 CR3: 00000001396ee000 CR4: 00000000000206e0
[ 532.369046] Call Trace:
[ 532.369159] [<ffffffff84c8192e>] qdisc_create+0x36e/0x450
[ 532.369268] [<ffffffff846a9b49>] ? ns_capable+0x29/0x50
[ 532.369366] [<ffffffff849afde2>] ? nla_parse+0x32/0x120
[ 532.369442] [<ffffffff84c81b4c>] tc_modify_qdisc+0x13c/0x610
[ 532.371508] [<ffffffff84c693e7>] rtnetlink_rcv_msg+0xa7/0x260
[ 532.372668] [<ffffffff84907b65>] ? sock_has_perm+0x75/0x90
[ 532.373790] [<ffffffff84c69340>] ? rtnl_newlink+0x890/0x890
[ 532.374914] [<ffffffff84c8da7b>] netlink_rcv_skb+0xab/0xc0
[ 532.376055] [<ffffffff84c63708>] rtnetlink_rcv+0x28/0x30
[ 532.377204] [<ffffffff84c8d400>] netlink_unicast+0x170/0x210
[ 532.378333] [<ffffffff84c8d7a8>] netlink_sendmsg+0x308/0x420
[ 532.379465] [<ffffffff84c2f3a6>] sock_sendmsg+0xb6/0xf0
[ 532.380710] [<ffffffffc034a56e>] ? __xfs_filemap_fault+0x8e/0x1d0 [xfs]
[ 532.381868] [<ffffffffc034a75c>] ? xfs_filemap_fault+0x2c/0x30 [xfs]
[ 532.383037] [<ffffffff847ec23a>] ? __do_fault.isra.61+0x8a/0x100
[ 532.384144] [<ffffffff84c30269>] ___sys_sendmsg+0x3e9/0x400
[ 532.385268] [<ffffffff847f3fad>] ? handle_mm_fault+0x39d/0x9b0
[ 532.386387] [<ffffffff84d88678>] ? __do_page_fault+0x238/0x500
[ 532.387472] [<ffffffff84c31921>] __sys_sendmsg+0x51/0x90
[ 532.388560] [<ffffffff84c31972>] SyS_sendmsg+0x12/0x20
[ 532.389636] [<ffffffff84d8dede>] system_call_fastpath+0x25/0x2a
[ 532.390704] [<ffffffff84d8de21>] ? system_call_after_swapgs+0xae/0x146
[ 532.391753] Code: 00 00 00 00 00 00 5b 5d c3 66 2e 0f 1f 84 00 00 00 00 00 66 66 66 66 90 55 48 89 e5 41 55 41 54 53 48 8b b7 48 01 00 00 48 89 fb <48> 8b 8e a8 00 00 00 48 85 c9 74 43 48 89 ca eb 0f 0f 1f 80 00
[ 532.394036] RIP [<ffffffffc06124a8>] teql_destroy+0x18/0x100 [sch_teql]
[ 532.395127] RSP <ffff8b7c9fdbf8e0>
[ 532.396179] CR2: 00000000000000a8
Null pointer dereference happens on master->slaves dereference in
teql_destroy() as master is null-pointer.
When qdisc_create() calls teql_qdisc_init() it imediately fails after
check "if (m->dev == dev)" because both devices are teql0, and it does
not set qdisc_priv(sch)->m leaving it zero on error path, then
qdisc_create() imediately calls teql_destroy() which does not expect
zero master pointer and we get OOPS.
Fixes: 87b60cfacf9f ("net_sched: fix error recovery at qdisc creation")
Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2021-04-08
The following pull-request contains BPF updates for your *net* tree.
We've added 4 non-merge commits during the last 2 day(s) which contain
a total of 4 files changed, 31 insertions(+), 10 deletions(-).
The main changes are:
1) Validate and reject invalid JIT branch displacements, from Piotr Krysiuk.
2) Fix incorrect unhash restore as well as fwd_alloc memory accounting in
sock map, from John Fastabend.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes berg says:
====================
Various small fixes:
* S1G beacon validation
* potential leak in nl80211
* fast-RX confusion with 4-addr mode
* erroneous WARN_ON that userspace can trigger
* wrong time units in virt_wifi
* rfkill userspace API breakage
* TXQ AC confusing that led to traffic stopped forever
* connection monitoring time after/before confusion
* netlink beacon head validation buffer overrun
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting iftoken can fail for several different reasons but there
and there was no report to user as to the cause. Add netlink
extended errors to the processing of the request.
This requires adding additional argument through rtnl_af_ops
set_link_af callback.
Reported-by: Hongren Zheng <li@zenithal.me>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vlad Buslov says:
====================
Action initalization fixes
This series fixes reference counting of action instances and modules in
several parts of action init code. The first patch reverts previous fix
that didn't properly account for rollback from a failure in the middle of
the loop in tcf_action_init() which is properly fixed by the following
patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With recent changes that separated action module load from action
initialization tcf_action_init() function error handling code was modified
to manually release the loaded modules if loading/initialization of any
further action in same batch failed. For the case when all modules
successfully loaded and some of the actions were initialized before one of
them failed in init handler. In this case for all previous actions the
module will be released twice by the error handler: First time by the loop
that manually calls module_put() for all ops, and second time by the action
destroy code that puts the module after destroying the action.
Reproduction:
$ sudo tc actions add action simple sdata \"2\" index 2
$ sudo tc actions add action simple sdata \"1\" index 1 \
action simple sdata \"2\" index 2
RTNETLINK answers: File exists
We have an error talking to the kernel
$ sudo tc actions ls action simple
total acts 1
action order 0: Simple <"2">
index 2 ref 1 bind 0
$ sudo tc actions flush action simple
$ sudo tc actions ls action simple
$ sudo tc actions add action simple sdata \"2\" index 2
Error: Failed to load TC action module.
We have an error talking to the kernel
$ lsmod | grep simple
act_simple 20480 -1
Fix the issue by modifying module reference counting handling in action
initialization code:
- Get module reference in tcf_idr_create() and put it in tcf_idr_release()
instead of taking over the reference held by the caller.
- Modify users of tcf_action_init_1() to always release the module
reference which they obtain before calling init function instead of
assuming that created action takes over the reference.
- Finally, modify tcf_action_init_1() to not release the module reference
when overwriting existing action as this is no longer necessary since both
upper and lower layers obtain and manage their own module references
independently.
Fixes: d349f9976868 ("net_sched: fix RTNL deadlock again caused by request_module()")
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Action init code increments reference counter when it changes an action.
This is the desired behavior for cls API which needs to obtain action
reference for every classifier that points to action. However, act API just
needs to change the action and releases the reference before returning.
This sequence breaks when the requested action doesn't exist, which causes
act API init code to create new action with specified index, but action is
still released before returning and is deleted (unless it was referenced
concurrently by cls API).
Reproduction:
$ sudo tc actions ls action gact
$ sudo tc actions change action gact drop index 1
$ sudo tc actions ls action gact
Extend tcf_action_init() to accept 'init_res' array and initialize it with
action->ops->init() result. In tcf_action_add() remove pointers to created
actions from actions array before passing it to tcf_action_put_many().
Fixes: cae422f379f3 ("net: sched: use reference counting action init")
Reported-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 6855e8213e06efcaf7c02a15e12b1ae64b9a7149.
Following commit in series fixes the issue without introducing regression
in error rollback of tcf_action_destroy().
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When I removed myself as a maintainer of the yaml file, I missed that
some maintainer is required. Oleksij is already listed in MAINTAINERS
for this file, so add him here as well.
Fixes: 1ae6b3780848 ("i2c: imx: drop me as maintainer of binding docs")
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
WARNING: CPU: 5 PID: 227 at fs/io_uring.c:8578 io_ring_exit_work+0xe6/0x470
RIP: 0010:io_ring_exit_work+0xe6/0x470
Call Trace:
process_one_work+0x206/0x400
worker_thread+0x4a/0x3d0
kthread+0x129/0x170
ret_from_fork+0x22/0x30
INFO: task lfs-openat:2359 blocked for more than 245 seconds.
task:lfs-openat state:D stack: 0 pid: 2359 ppid: 1 flags:0x00000004
Call Trace:
...
wait_for_completion+0x8b/0xf0
io_wq_destroy_manager+0x24/0x60
io_wq_put_and_exit+0x18/0x30
io_uring_clean_tctx+0x76/0xa0
__io_uring_files_cancel+0x1b9/0x2e0
do_exit+0xc0/0xb40
...
Even after io-wq destroy has been issued io-wq worker threads will
continue executing all left work items as usual, and may hang waiting
for I/O that won't ever complete (aka unbounded).
[<0>] pipe_read+0x306/0x450
[<0>] io_iter_do_read+0x1e/0x40
[<0>] io_read+0xd5/0x330
[<0>] io_issue_sqe+0xd21/0x18a0
[<0>] io_wq_submit_work+0x6c/0x140
[<0>] io_worker_handle_work+0x17d/0x400
[<0>] io_wqe_worker+0x2c0/0x330
[<0>] ret_from_fork+0x22/0x30
Cancel all unbounded I/O instead of executing them. This changes the
user visible behaviour, but that's inevitable as io-wq is not per task.
Suggested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/cd4b543154154cba055cf86f351441c2174d7f71.1617842918.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
WARNING: at fs/io_uring.c:8578 io_ring_exit_work.cold+0x0/0x18
As reissuing is now passed back by REQ_F_REISSUE and kiocb_done()
internally uses __io_complete_rw(), it may stop after setting the flag
so leaving a dangling request.
There are tricky edge cases, e.g. reading beyound file, boundary, so
the easiest way is to hand code reissue in kiocb_done() as
__io_complete_rw() was doing for us before.
Fixes: 230d50d448ac ("io_uring: move reissue into regular IO path")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/f602250d292f8a84cca9a01d747744d1e797be26.1617842918.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
