| Age | Commit message (Collapse) | Author |
|---|
|
I received a report this morning from one of the Novena developers that
the behaviour of the iMX6 ASoC codec driver (using imx-pcm-dma.c) was
sub-optimal under high system load.
While there are issues relating to system load remaining, upon reviewing
the ASoC imx-pcm-dma.c driver, it was noticed that it not using the
residue support, because SDMA doesn't support it. This has the effect
that SDMA has to make multiple calls into the ASoC and ALSA code, one
for each period.
Since ALSA's snd_pcm_elapsed() does not need to be called multiple times
and it is entirely sufficient to call it once to update ALSA with the
current buffer position via the pointer method, we can do better here.
We can also avoid stopping the DMA entirely, just like real cyclic DMA
implementations behave. While this means that we replay some old samples,
this is a nicer behaviour than having audio stop and restart.
The changes to achieve this are relatively minor - imx-sdma.c can track
where the DMA is to the nearest descriptor boundary - it does this
already when deciding how many callbacks to issue. In doing this,
buf_tail always points at the descriptor which will complete next.
The residue is defined by the bytes remaining to the end of the buffer,
when the buffer is viewed as a single block of memory [start...end].
So, when we start out, there's a full buffer worth of residue, and this
counts down as we approach the end of the buffer, eventually becoming
zero at the end, before returning to the full buffer worth when we
wrap back to the start.
Moving the walking of the descriptors into the interrupt handler means
that we can update the BD_DONE flag at interrupt time, thus avoiding
a delayed tasklet stopping the cyclic DMA.
This means that the residue can be calculated from (total descriptors -
buf_tail) * descriptor size. This is what the change below does. We
update imx-pcm-dma.c to remove the NO_RESIDUE flag since we now provide
the residue.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
When a 0-length packet is received on the bus, desc->pd0 yields 1,
which confuses the driver's users. This information is clearly wrong
and not in accordance to the datasheet, but it's been observed on an
AM335x board, very reproducible.
Fix this by looking at bit 19 in PD2 of the completed packet. This bit
will tell us if a zero-length packet was received on a queue. If it's
set, ignore the value in PD0 and report a total length of 0 instead.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This patch makes the msm ehci driver available to use on QCOM SOCs,
which have the same IP.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some buggy JMicron USB-ATA bridges don't know how to translate the FUA
bit in READs or WRITEs. This patch adds an entry in unusual_devs.h
and a blacklist flag to tell the sd driver not to use FUA.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Michael Büsch <m@bues.ch>
Tested-by: Michael Büsch <m@bues.ch>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.16-rc4
A few more fixes for this RC cycle. There's a revert of a previous patch
which ended up being the wrong version, so we reverted that commit and
applied a better fix.
CPPI41 got a race condition fix which was found by Thomas Gleixner.
The MSM PHY driver got a runtime pm usage fix so that it wouldn't
kill the PHY while it was still being used.
We also have a fix for a panic caused when removing musb_am335x driver.
Other than that, a few other minor fixes.
Signed-of-by: Felipe Balbi <balbi@ti.com>
|
|
tmon fails to build statically with the following error:
$ make LDFLAGS=-static
gcc -O1 -Wall -Wshadow -W -Wformat -Wimplicit-function-declaration -Wimplicit-int -fstack-protector -D VERSION=\"1.0\" -static tmon.o tui.o sysfs.o pid.o -o tmon -lm -lpanel -lncursesw -lpthread
tmon.o: In function `tmon_sig_handler':
tmon.c:(.text+0x21): undefined reference to `stdscr'
tmon.o: In function `tmon_cleanup':
tmon.c:(.text+0xb9): undefined reference to `stdscr'
tmon.c:(.text+0x11e): undefined reference to `stdscr'
tmon.c:(.text+0x123): undefined reference to `keypad'
tmon.c:(.text+0x12d): undefined reference to `nocbreak'
tmon.o: In function `main':
tmon.c:(.text+0x785): undefined reference to `stdscr'
tmon.c:(.text+0x78a): undefined reference to `nodelay'
tui.o: In function `setup_windows':
tui.c:(.text+0x131): undefined reference to `stdscr'
tui.c:(.text+0x176): undefined reference to `stdscr'
tui.c:(.text+0x19f): undefined reference to `stdscr'
tui.c:(.text+0x1cc): undefined reference to `stdscr'
tui.c:(.text+0x1ff): undefined reference to `stdscr'
tui.o:tui.c:(.text+0x229): more undefined references to `stdscr' follow
tui.o: In function `show_cooling_device':
[...]
stdscr() and friends are in libtinfo (part of ncurses) so add it to
the libraries that are linked in when compiling tmon to fix it.
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
|
|
Wrong address is checked after memory allocation.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
On latest i.MX6 SOC with thermal calibration data of 0x5A100000,
the critical trip temperature will be an invalid value and
cause system auto shutdown as below log:
thermal thermal_zone0: critical temperature reached(42 C),shutting down
So, with universal formula for thermal sensor, only room
temperature point is calibrated, which means the calibration
data read from fuse only has valid data of bit [31:20], others
are all 0, the critical trip point temperature can NOT depend
on the hot point calibration data, here we set it to 20 C higher
than default passive temperature.
Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Use clk_prepare_enable/clk_disable_unprepare to make the driver
work properly with common clock framework.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The musb/cppi41 code installs a hrtimer to work around DMA completion
interrupts that have fired too early on AM335x hardware. This timer
is currently programmed to first fire 140 microseconds after the DMA
completion callback. According to the commit which introduced it
(a655f481d83, "usb: musb: musb_cppi41: handle pre-mature TX complete
interrupt"), that value is is considered a 'rule of thumb' that worked
well with the test case described in the commit log.
Test show, however, that for USB audio devices and much smaller packet
sizes, the timer has to fire earlier in order to correctly handle the audio
stream. The original test case had output transfer sizes of 1514 bytes, and
a delay of 140 microseconds. For audio devices with 24 bytes channel size, 3
microseconds seem to work well.
Hence, let's assume that the time it takes to clear the bit correlates with
the number of bytes transferred. The referenced commit log mentions such a
suspicion as well. Let the timer fire in cppi41_channel->total_len/10
microseconds to correctly handle both cases.
Also, shorten the interval in which the timer fires again in case of
a non-empty early_tx list.
With these changes in place, both FS and HS audio devices appear to work
well on AM335x hardware.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
hrtimer."
This reverts commit 1af54b7a4.
The commit tried to address cases in which isochronous transfers are 'not
reliable', most probably in the tests conducted, polling for the
MUSB_TXCSR_TXPKTRDY bit in MUSB_TXCSR is done too late.
Hence, it installs a work struct which basically busy-polls for the bit in a
rather agressive way by rescheduling the work if the FIFO is not empty. With
USB audio devices, tests have shown that it takes approximately 100
iterations of the asynchronous worker until the FIFO signals completion,
which leads to 100% CPU loads when streaming audio.
The issue the patch tried to address can be handled differently, which is
what the next patch does.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Just a cosmetic cleanup with no functional change.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Before accessing any of an endpoint's CSR registers, make sure the
correct endpoint is selected. Otherwise, data read from or written to
the registers is likely to affect the wrong endpoint as long as the
connected device has more than one endpoint.
This, of course, leads to all sorts of strange effects such as stream
starvation and driver internal state machine confusion due to spurious
interrupts.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The musb/cppi41 glue layer is capable of handling transactions that span
over more than one USB packet by reloading the DMA descriptors
partially. An urb is considered completed when either its transfer
buffer has been filled entirely (actual_length ==
transfer_buffer_length) or if a packet in the stream has less bytes than
the endpoint's wMaxPacketSize.
Once one of the above conditions is met, musb_dma_completion() is called
from cppi41_trans_done(). However, the final decision whether or not to
return the urb to its owner is made by the core and its determination of
the variable 'done' in musb_host_rx(). This code has currently no way of
knowing what the size of the last packet was, and whether or not to
give back the urb due to a short read.
Fix this by introducing a new boolean flag in 'struct dma_channel', and
set it from musb_cppi41.c. If set, it will make the core do what the
DMA layer decided and complete the urb.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The datasheet says that MUSB_TXCSR_FLUSHFIFO is only valid when
MUSB_TXCSR_TXPKTRDY is set as well.
With this patch applied, the warning in this function does no longer
kick in when an USB soundcard is unplugged while the stream is active.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
On AM33xx platforms, unplugging a device in the middle of an active
transfer leads to a drop of MUSB_DEVCTL_HM in MUSB_DEVCTL before the
system is informed about a disconnect. This consequently makes the musb
core call the gadget code to handle the interrupt request, which then
crashes the kernel because the relevant pointers haven't been set up
for gadget mode.
To fix this, use is_host_active() rather than (devctl & MUSB_DEVCTL_HM)
in musb_interrupt() and musb_dma_completion() to detect whether the
controller is in host or peripheral mode. This information is provided
by the driver logic and does not rely on register contents.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Just a little cleanup that removes unnecessary casts.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
commit 943c13971c08 "usb: musb: dsps: implement ->set_mode()"
should have made it possible to use the driver with boards that have
the USBID pin unconnected. This doesn't actually work, since the
driver uses the wrong base address to access the mode register.
Furthermore it uses different base addresses in different places to
access the same register (phy_utmi).
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
found.
Syscall mount returns -ENODEV error if requested FS type
has not been found. Returning the same error from FFS mount
callback makes value returned to userspace misleading.
Other file systems returns -ENOENT if requested device
has not been found. Adjust FFS to this convention to make
error codes meaningfull.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
It has already been covered by udc core
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
It has already been covered by udc core, besides, we do not
need unbind at .udc_start
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
It has already been covered by udc core
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
It has already been covered by udc core
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
It has already been covered by udc core
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
It appears that no one ever run ffs-test on a big-endian machine,
since it used cpu-endianess for fs_count and hs_count fields which
should be in little-endian format. Fix by wrapping the numbers in
cpu_to_le32.
Cc: stable@vger.kernel.org
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Use case is when the phy is configured in host mode and a usb device is
attached to board before bootup. On bootup, with the existing code and
runtime pm enabled, the driver would decrement the pm usage count
without checking the current state of the phy. This pm usage count
decrement would trigger the runtime pm which than would abort the
usb enumeration which was in progress. In my case a usb stick gets
detected and then immediatly the driver goes to low power mode which is
not correct.
log:
[ 1.631412] msm_hsusb_host 12520000.usb: EHCI Host Controller
[ 1.636556] msm_hsusb_host 12520000.usb: new USB bus registered, assigned bus number 1
[ 1.642563] msm_hsusb_host 12520000.usb: irq 220, io mem 0x12520000
[ 1.658197] msm_hsusb_host 12520000.usb: USB 2.0 started, EHCI 1.00
[ 1.659473] hub 1-0:1.0: USB hub found
[ 1.663415] hub 1-0:1.0: 1 port detected
...
[ 1.973352] usb 1-1: new high-speed USB device number 2 using msm_hsusb_host
[ 2.107707] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 2.108993] scsi0 : usb-storage 1-1:1.0
[ 2.678341] msm_otg 12520000.phy: USB in low power mode
[ 3.168977] usb 1-1: USB disconnect, device number 2
This issue was detected on IFC6410 board.
This patch fixes the intial runtime pm trigger by checking the phy
state and decrementing the pm use count only when the phy state is IDLE.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
On Marvell Armada XP, when a CPU comes back from deep idle state of
cpuidle, it restarts its execution at armada_370_xp_cpu_resume(),
which puts back the CPU into the coherency, and then calls the generic
cpu_resume() function.
While this works on little-endian configurations, it doesn't work on
big-endian configurations because the CPU restarts in little-endian,
and therefore must be switched back to big-endian to operate
properly. To achieve this, a 'setend be' instruction must be executed
in big-endian configurations. However, the ARM_BE8() macro that is
used to implement nice compile-time conditional for ARM LE vs. ARM BE8
is not easily usable in inline assembly.
Therefore, this patch moves the armada_370_xp_cpu_resume() C function,
which was anyway just a block of inline assembly, into a proper
pmsu_ll.S file, and adds the appropriate ARM_BE8(setend be)
instruction.
Without this patch, an Armada XP big endian configuration with cpuidle
enabled fails to boot, as it hangs as soon as one of the CPU hits the
deep idle state.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1404130165-3593-1-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This patch makes the phy reset clk and reset line optional as this clk
is not available on boards like IFC6410 with APQ8064.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Add clock prepare and unprepare as required by clock framework.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Add missing information about license. Some people will probably want to
reuse this code in their projects released under variety of licenses. For this
reason this example is under Public Domain license to avoid GPL limitations.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Since commit [ac8dde11: “Add flags to descriptors block”] functionfs
supports a new descriptor format, so we update example application
to make it using recomended version of descriptors.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
We wrap numeric values of fs_count and hs_count fields in htole32,
because they should be in little-endian format.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Commit 497a92308af8e9385fa3d135f7f416a997e4b93b ("ARM: mvebu:
implement L2/PCIe deadlock workaround") introduced some logic in
coherency.c to adjust the PL310 cache controller Device Tree node of
Armada 375 and Armada 38x platform to include the 'arm,io-coherent'
property if the system is running with hardware I/O coherency enabled.
However, with the L2CC driver cleanup done by Russell King, the
initialization of the L2CC driver has been moved earlier, and is now
part of the init_IRQ() ARM function in
arch/arm/kernel/irq.c. Therefore, calling coherency_init() in
->init_time() is now too late, as the Device Tree property gets added
too late (after the L2CC driver has been initialized).
In order to fix this, this commit removes the ->init_time() callback
use in board-v7.c and replaces it with an ->init_irq() callback. We
therefore no longer use the default ->init_irq() callback, but we now
use the default ->init_time() callback.
In this newly introduced ->init_irq() callback, we call irqchip_init()
which is the default behavior when ->init_irq() isn't defined, and
then do the initialization related to the coherency: SCU, coherency
fabric, and mvebu-mbus (which is needed to start secondary CPUs).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1402585772-10405-4-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
In preparation to a small re-organization of the initialization
sequence in board-v7.c, this commit moves the registration of the
custom external abort handler on Armada 375 later in the boot
sequence, and makes it more similar to the other quirks that we
already have. There is indeed no need to register this abort handler
particularly early, it simply needs to be registered before switching
to userspace.
In addition to this, this commit makes the registration of the custom
abort handler conditional on Armada 375 Z1, because Armada 375 A0 and
later iterations are not affected by the issue.
This commit was tested on both Armada 375 Z1 and Armada 375 A0
platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1402585772-10405-3-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Use of quirks improve readability and will be easier to add new devices
to this driver.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Driver was using custom functions WARNING, ERROR, DEBUG, instead of
pr_err, pr_dgb...
New ep_* macros have been created that use standard pr_* functions.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
- Move logical continuations to end of line
- Improve spacing
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Fix Code Style using checkpatch.pl criteria
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Replace a long and ugly expresion with an already available function.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
For bool variables
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Improves readability of the code
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Instead of using magic numbers use #defines
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch adds support for the PLX USB3380 and USB3382.
This driver is based on the driver from the manufacturer.
Since USB338X is register compatible with NET2280, I thought that it
would be better to include this hardware into net2280 driver.
Manufacturer's driver only supported the USB33X, did not follow the
Kernel Style and contain some trivial errors. This patch has tried to
address this issues.
This patch has only been tested on USB338x hardware, but the merge has
been done trying to not affect the behaviour of NET2280.
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The probe function may be probed deferal and called after .init
section has freed.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The probe function may be probed deferal and called after .init
section has freed.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The probe function may be probed deferal and called after .init
section has freed.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The probe function may be probed deferal and called after .init
section has freed.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The probe function may be probed deferal and called after .init
section has freed.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The probe function may be probed deferal and called after .init
section has freed.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
