| Age | Commit message (Collapse) | Author |
|---|
|
Use sdhci-caps-mask to forbid SDR104 mode on the SDIO capable SDHCI
controller. Without this the device cannot pass electromagnetic
interference certifications.
Fixes: 7109d817db2e ("arm64: dts: marvell: add DTS for Turris Mox")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The Arm Ltd. boards were using an outdated address convention in the DT
node names, by separating the high from the low 32-bits of an address by
a comma.
Remove the comma from the node name suffix to be DT spec compliant.
Link: https://lore.kernel.org/r/20200513103016.130417-3-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The NV+ v2 has a WH1602 LCD panel (which is just a rebranded HD44780),
similar to the Netgear RN104, just with different GPIO assignments.
Signed-off-by: Brian J. Tarricone <brian@tarricone.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This patch adds dts for the Check Point L-50 from 600/1100 series
routers.
Specification:
-CPU: Marvell Kirkwood 88F6821 1200MHz
-RAM: 512MB
-Flash: NAND 512MB
-WiFi: mPCIe card based on Atheros AR9287 b/g/n
-WAN: 1 Gigabit Port (Marvell 88E1116R PHY)
-LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+4))
-USB: 2x USB2.0
-Express card slot
-SD card slot
-Serial console: RJ-45 115200 8n1
-Unsupported DSL
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The timeout-ms property for i2c master nodes is undocumented, and as
never been supported. Drop it.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The timeout-ms property for i2c master nodes is undocumented, and as
never been supported. Drop it.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Move the max-link-speed property of the PCIe node from board specific
device tree files to the generic armada-37xx.dtsi.
Armada 37xx supports only PCIe gen2 speed so max-link-speed property
should be in the generic armada-37xx.dtsi file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Move the comphy handle property of the PCIe node from board specific
device tree files (EspressoBin and Turris Mox) to the generic
armada-37xx.dtsi.
This is correct since this is the only possible PCIe PHY configuration
on Armada 37xx, so when PCIe is enabled on any board, this handle is
correct.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
We found out that we are unable to control the PERST# signal via the
default pin dedicated to be PERST# pin (GPIO2[3] pin) on A3700 SOC when
this pin is in EP_PCIE1_Resetn mode. There is a register in the PCIe
register space called PERSTN_GPIO_EN (D0088004[3]), but changing the
value of this register does not change the pin output when measuring
with voltmeter.
We do not know if this is a bug in the SOC, or if it works only when
PCIe controller is in a certain state.
Commit f4c7d053d7f7 ("PCI: aardvark: Wait for endpoint to be ready
before training link") says that when this pin changes pinctrl mode
from EP_PCIE1_Resetn to GPIO, the PERST# signal is asserted for a brief
moment.
So currently the situation is that on A3700 boards the PERST# signal is
asserted in U-Boot (because the code in U-Boot issues reset via this pin
via GPIO mode), and then in Linux by the obscure and undocumented
mechanism described by the above mentioned commit.
We want to issue PERST# signal in a known way, therefore this patch
changes the pcie_reset_pin function from "pcie" to "gpio" and adds the
reset-gpios property to the PCIe node in device tree files of
EspressoBin and Armada 3720 Dev Board (Turris Mox device tree already
has this property and uDPU does not have a PCIe port).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Remi Pommarel <repk@triplefau.lt>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Update the SolidRun Armada 8040 platforms phy interface types from the
old 10gbase-kr to the newer and more correct 10gbase-r.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Add musb nodes and usb2 phy nodes for MT2701
Signed-off-by: Min Guo <min.guo@mediatek.com>
Link: https://lore.kernel.org/r/20191211015446.11477-3-min.guo@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The MediaTek MT7623 SoC contains a Mali-450, so add a compatible for it
and define its own vendor-specific properties.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/efeadefe3895bcadf1d2e9847b82206dd8c7ec35.1563867856.git.ryder.lee@mediatek.com
[mb: move to yaml file]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Add a node for Mali-450.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Link: https://lore.kernel.org/r/af7b5a2e00eb3a4b6262807c378e43afd5f74779.1563867856.git.ryder.lee@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Dhrystone benchmark on Acer Chromebook R13 CB5-312T:
A72: 15698587 dps @ 1807 MHz
A53: 7598784 dps @ 1703 MHz
Signed-off-by: Ulrich Hecht <uli-qwV78thtvt0@public.gmane.org>
Link: https://lore.kernel.org/r/1563529816-3992-1-git-send-email-uli@fpond.eu
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Use non-empty ranges for usb-phy to make the layout of
its registers clearer;
Replace deprecated compatible by generic
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Fix warning:
Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-'
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://lore.kernel.org/r/20200414030815.192104-1-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Switch to SPDX license identifier for MT6797 SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200222162444.11590-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
There are 7 I2C ports used on this board. Hence, enable all of them.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200222162444.11590-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Add I2C support for Mediatek MT6797 SoC. There are a total of 8 I2C
controllers in this SoC (2 being shared) and they are same as the
controllers present in MT6577 SoC. Hence, the driver support is added with
DT fallback method.
As per the datasheet, there are controllers with _imm prefix like i2c2_imm
and i2c3_imm. These appears to be in different memory regions but sharing
the same pins with i2c2 and i2c3 respectively. Since there is no clear
evidence of what they really are, I've adapted the numbering/naming scheme
from the downstream code by Mediatek.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200222162444.11590-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
I2C controller driver for MT6577 SoC is reused for MT6797 SoC. Hence,
document that in DT binding.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20200222162444.11590-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
This patch adds the required dt nodes and properties
to enabled A618 GPU.
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Link: https://lore.kernel.org/r/1588329036-18732-1-git-send-email-smasetty@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
This patch simply adds a new compatible string for SC7180 platform.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Link: https://lore.kernel.org/r/1588329036-18732-2-git-send-email-smasetty@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The SCL gpio pin used by I2C bus for recovery needs to be configured as
open drain.
Fixes: 455fec938bbb ("ARM: dts: at91: sama5d2: add i2c gpio pinctrl")
Fixes: a4bd8da893a3 ("ARM: dts: at91: sama5d3: add i2c gpio pinctrl")
Fixes: 8fb82f050cf6 ("ARM: dts: at91: sama5d4: add i2c gpio pinctrl")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20200515140001.287932-1-codrin.ciubotariu@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
When thermal reaches target temperature,it would be pinned to state 0
(max frequency and power).
Fix the throttling range to no limit.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Link: https://lore.kernel.org/r/20200424082340.4127-1-michael.kao@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Users can choose which flexcom function to use. Describe the I2C
Flexcom0 function. Add alias for the i2c2 node in order to not rely
on probe order for the i2c device numbering. The sama5d2 SoC has
two dedicated i2c buses and five flexcoms that can function as i2c.
The i2c0 and i2c1 aliases are kept for the dedicated i2c buses,
the i2c flexcom functions can be numbered in order starting from i2c2.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-16-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Indicate which i2c alias is for which connector on the board.
Specify that serial0 is for DBGU. This eases tester's life.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-17-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The aliases should be defined in the board dts rather than in the
SoC dtsi. Don't rely on the aliases defined in the SoC dtsi and define
the alias for the Serial DBGU in the board dts file. sama5d2 boards use
the "serial0" alias for the Serial DBGU, do the same for sama5d2_xplained.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-15-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Describe all the flexcom functions for all the flexcom nodes.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-13-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Device aliases are board-specific, if needed one should define them
in board dts rather than in the SoC dtsi. If an alias from the SoC
dtsi is addressed by a driver that does not use any of the of_alias*()
methods, we can drop it. This is the case for the i2s aliases, drop
them. tcb aliases point to nodes that are not enabled in any of the
sama5d2 based platforms. atmel_tclib.c is scheduled to go away, any
board using that alias is already broken, so get rid of the tcb aliases
too.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-14-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Spare boards of duplicating the DMA bindings. Describe the flx0
DMA bindings in the SoC dtsi. Users that don't want to use DMA
for their flexcom functions have to overwrite the flexcom DMA
bindings in their board device tree.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-12-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Spare boards of duplicating the DMA bindings. Describe the flx1
DMA bindings in the SoC dtsi. Users that don't want to use DMA
for their flexcom functions have to overwrite the flexcom DMA
bindings in their board device tree.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-11-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Spare boards of duplicating the DMA bindings. Describe the flx3
DMA bindings in the SoC dtsi. Users that don't want to use DMA
for their flexcom functions have to overwrite the flexcom DMA
bindings in their board device tree.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-10-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Spare boards of duplicating the DMA bindings. Describe the flx4
DMA bindings in the SoC dtsi. Users that don't want to use DMA
for their flexcom functions have to overwrite the flexcom DMA
bindings in their board device tree.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-9-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The UART submodule in Flexcom has 32-byte Transmit and Receive FIFOs.
Tested uart7 on sama5d2-icp, which has both DMA and FIFO enabled.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-8-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The Flexcom IP is part of the sama5d2 SoC. Move the flx0 node together
with its function definitions in sama5d2.dtsi. Boards will just fill
the pins and enable the desired functions.
There is a single functional change in this patch. With the move of the
flx0 uart5 definition in the SoC dtsi, the uart5 from
at91-sama5d27_wlsom1_ek.dts inherits the following optional property:
atmel,fifo-size = <32>;
This particular change was tested by Codrin.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-7-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The Flexcom IP is part of the sama5d2 SoC. Move the flx0 node together
with its function definitions in sama5d2.dtsi. Boards will just fill
the pins and enable the desired functions.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-6-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The Flexcom IP is part of the sama5d2 SoC. Move the flx2 node together
with its function definitions in sama5d2.dtsi. Boards will just fill
the pins and enable the desired functions.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-5-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The Flexcom IP is part of the sama5d2 SoC. Move the flx3 node together
with its function definitions in sama5d2.dtsi. Boards will just fill
the pins and enable the desired functions.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-4-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The Flexcom IP is part of the sama5d2 SoC. Move the flx0 node together
with its function definitions in sama5d2.dtsi. Boards will just fill
the pins and enable the desired functions.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-3-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The sama5d2 SoC has the following IPs: [uart0, uart4], {spi0, spi1}, {i2c0, i2c1}.
Label the flexcom functions in order:
flx0: uart5, spi2, i2c2
flx1: uart6, spi3, i2c3
flx2: uart7, spi4, i2c4
flx3: uart8, spi5, i2c5
flx4: uart9, spi6, i2c6
Some boards respected this scheme, others not. Fix the ones that didn't.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-2-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Document the iW-RainboW-G21D-Qseven-RZG1H device tree bindings,
listing it as a supported board.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1588542414-14826-9-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Document the iW-RainboW-G21M-Qseven-RZG1H device tree bindings,
listing it as a supported system on module.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1588542414-14826-8-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Now that we have a driver for the IOMMU, let's start using it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Presumably the GPU node needs to control both the GPU and GPU GX power
domains, but given that GPU GX now depends on the GPU GDSC both can
effectively be controlled by controlling GPU GX. So use this instead.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200417070044.1376212-5-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add the SPMI regulator node in the PMI8994, use it to give us VDD_GX
at a fixed max nominal voltage for the db820c and specify this as supply
for the MMSS GPU_GX GDSC.
With the introduction of CPR support the range for VDD_GX should be
expanded.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/20200417070044.1376212-4-bjorn.andersson@linaro.org
[bjorn: Split between pmi8994 and db820c, changed voltage, rewrote commit message]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
apq8016-sbc.dtsi is the only remaining device which takes up
4 files since it has its pinctrl split into separate files.
Actually this does not really make the device tree easier to read
(just harder to find nodes). For db820c the files were merged in
commit 88264f1f6bf5 ("arm64: dts: qcom: db820c: Remove pin specific files").
Do the same for apq8016-sbc (db410c) and move the pinctrl definitions
into apq8016-sbc.dtsi.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200514112754.148919-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
In msm8916.dtsi the GPU OPP table is defined under the root node,
whereas in msm8996.dtsi/sdm845.dtsi it is a subnode of the gpu device
(which makes it easier to find).
Move it to the gpu device node to make this consistent.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200514112754.148919-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Many nodes in the MSM8916 device trees use '_' in node names
(especially pinctrl), even though (seemingly) '-' is preferred now.
Make this more consistent by replacing '_' with '-' where possible.
Similar naming is used for pinctrl in newer device trees (e.g. sdm845.dtsi).
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200514112754.148919-1-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
On some device the reset line for the UFS memory needs to be tickled in
order for UFS to initialize properly, add this to the ufs_mem_hc node.
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200406060049.227029-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
