| Age | Commit message (Collapse) | Author |
|---|
|
In the current implementation of ARM64 eBPF JIT, R23 and R24 are used for
tmp registers, which are callee-saved registers. This leads to variable size
of JIT prologue and epilogue. The latest blinding constant change prefers to
constant size of prologue and epilogue. AAPCS reserves R9 ~ R15 for temp
registers which not need to be saved/restored during function call. So, replace
R23 and R24 to R10 and R11, and remove tmp_used flag to save 2 instructions for
some jited BPF program.
CC: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In testing with HiKey, we found that since
commit 3f30b158eba5 ("asix: On RX avoid creating bad Ethernet
frames"),
we're seeing lots of noise during network transfers:
[ 239.027993] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.037310] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x54ebb5ec, offset 4
[ 239.045519] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0xcdffe7a2, offset 4
[ 239.275044] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.284355] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x1d36f59d, offset 4
[ 239.292541] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0xaef3c1e9, offset 4
[ 239.518996] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.528300] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x2881912, offset 4
[ 239.536413] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x5638f7e2, offset 4
And network throughput ends up being pretty bursty and slow with
a overall throughput of at best ~30kB/s (where as previously we
got 1.1MB/s with the slower USB1.1 "full speed" host).
We found the issue also was reproducible on a x86_64 system,
using a "high-speed" USB2.0 port but the throughput did not
measurably drop (possibly due to the scp transfer being cpu
bound on my slow test hardware).
After lots of debugging, I found the check added in the
problematic commit seems to be calculating the offset
incorrectly.
In the normal case, in the main loop of the function, we do:
(where offset is zero, or set to "offset += (copy_length + 1) &
0xfffe" in the previous loop)
rx->header = get_unaligned_le32(skb->data +
offset);
offset += sizeof(u32);
But the problematic patch calculates:
offset = ((rx->remaining + 1) & 0xfffe) + sizeof(u32);
rx->header = get_unaligned_le32(skb->data + offset);
Adding some debug logic to check those offset calculation used
to find rx->header, the one in problematic code is always too
large by sizeof(u32).
Thus, this patch removes the incorrect " + sizeof(u32)" addition
in the problematic calculation, and resolves the issue.
Cc: Dean Jenkins <Dean_Jenkins@mentor.com>
Cc: "David B. Robins" <linux@davidrobins.net>
Cc: Mark Craske <Mark_Craske@mentor.com>
Cc: Emil Goode <emilgoode@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Ivan Vecera <ivecera@redhat.com>
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: stable <stable@vger.kernel.org> #4.4+
Reported-by: Yongqin Liu <yongqin.liu@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull parallel filesystem directory handling update from Al Viro.
This is the main parallel directory work by Al that makes the vfs layer
able to do lookup and readdir in parallel within a single directory.
That's a big change, since this used to be all protected by the
directory inode mutex.
The inode mutex is replaced by an rwsem, and serialization of lookups of
a single name is done by a "in-progress" dentry marker.
The series begins with xattr cleanups, and then ends with switching
filesystems over to actually doing the readdir in parallel (switching to
the "iterate_shared()" that only takes the read lock).
A more detailed explanation of the process from Al Viro:
"The xattr work starts with some acl fixes, then switches ->getxattr to
passing inode and dentry separately. This is the point where the
things start to get tricky - that got merged into the very beginning
of the -rc3-based #work.lookups, to allow untangling the
security_d_instantiate() mess. The xattr work itself proceeds to
switch a lot of filesystems to generic_...xattr(); no complications
there.
After that initial xattr work, the series then does the following:
- untangle security_d_instantiate()
- convert a bunch of open-coded lookup_one_len_unlocked() to calls of
that thing; one such place (in overlayfs) actually yields a trivial
conflict with overlayfs fixes later in the cycle - overlayfs ended
up switching to a variant of lookup_one_len_unlocked() sans the
permission checks. I would've dropped that commit (it gets
overridden on merge from #ovl-fixes in #for-next; proper resolution
is to use the variant in mainline fs/overlayfs/super.c), but I
didn't want to rebase the damn thing - it was fairly late in the
cycle...
- some filesystems had managed to depend on lookup/lookup exclusion
for *fs-internal* data structures in a way that would break if we
relaxed the VFS exclusion. Fixing hadn't been hard, fortunately.
- core of that series - parallel lookup machinery, replacing
->i_mutex with rwsem, making lookup_slow() take it only shared. At
that point lookups happen in parallel; lookups on the same name
wait for the in-progress one to be done with that dentry.
Surprisingly little code, at that - almost all of it is in
fs/dcache.c, with fs/namei.c changes limited to lookup_slow() -
making it use the new primitive and actually switching to locking
shared.
- parallel readdir stuff - first of all, we provide the exclusion on
per-struct file basis, same as we do for read() vs lseek() for
regular files. That takes care of most of the needed exclusion in
readdir/readdir; however, these guys are trickier than lookups, so
I went for switching them one-by-one. To do that, a new method
'->iterate_shared()' is added and filesystems are switched to it
as they are either confirmed to be OK with shared lock on directory
or fixed to be OK with that. I hope to kill the original method
come next cycle (almost all in-tree filesystems are switched
already), but it's still not quite finished.
- several filesystems get switched to parallel readdir. The
interesting part here is dealing with dcache preseeding by readdir;
that needs minor adjustment to be safe with directory locked only
shared.
Most of the filesystems doing that got switched to in those
commits. Important exception: NFS. Turns out that NFS folks, with
their, er, insistence on VFS getting the fuck out of the way of the
Smart Filesystem Code That Knows How And What To Lock(tm) have
grown the locking of their own. They had their own homegrown
rwsem, with lookup/readdir/atomic_open being *writers* (sillyunlink
is the reader there). Of course, with VFS getting the fuck out of
the way, as requested, the actual smarts of the smart filesystem
code etc. had become exposed...
- do_last/lookup_open/atomic_open cleanups. As the result, open()
without O_CREAT locks the directory only shared. Including the
->atomic_open() case. Backmerge from #for-linus in the middle of
that - atomic_open() fix got brought in.
- then comes NFS switch to saner (VFS-based ;-) locking, killing the
homegrown "lookup and readdir are writers" kinda-sorta rwsem. All
exclusion for sillyunlink/lookup is done by the parallel lookups
mechanism. Exclusion between sillyunlink and rmdir is a real rwsem
now - rmdir being the writer.
Result: NFS lookups/readdirs/O_CREAT-less opens happen in parallel
now.
- the rest of the series consists of switching a lot of filesystems
to parallel readdir; in a lot of cases ->llseek() gets simplified
as well. One backmerge in there (again, #for-linus - rockridge
fix)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (74 commits)
ext4: switch to ->iterate_shared()
hfs: switch to ->iterate_shared()
hfsplus: switch to ->iterate_shared()
hostfs: switch to ->iterate_shared()
hpfs: switch to ->iterate_shared()
hpfs: handle allocation failures in hpfs_add_pos()
gfs2: switch to ->iterate_shared()
f2fs: switch to ->iterate_shared()
afs: switch to ->iterate_shared()
befs: switch to ->iterate_shared()
befs: constify stuff a bit
isofs: switch to ->iterate_shared()
get_acorn_filename(): deobfuscate a bit
btrfs: switch to ->iterate_shared()
logfs: no need to lock directory in lseek
switch ecryptfs to ->iterate_shared
9p: switch to ->iterate_shared()
fat: switch to ->iterate_shared()
romfs, squashfs: switch to ->iterate_shared()
more trivial ->iterate_shared conversions
...
|
|
The problem is that fib_info->nh is [0] so the struct fib_info
allocation size depends on number of nexthops. If we just copy fib_info,
we do not copy the nexthops info and driver accesses memory which is not
ours.
Given the fact that fib4 does not defer operations and therefore it does
not need copy, just pass the pointer down to drivers as it was done
before.
Fixes: 850d0cbc91 ("switchdev: remove pointers from switchdev objects")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"This update delivers:
- Yet another interrupt chip diver (LPC32xx)
- Core functions to handle partitioned per-cpu interrupts
- Enhancements to the IPI core
- Proper handling of irq type configuration
- A large set of ARM GIC enhancements
- The usual pile of small fixes, cleanups and enhancements"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
irqchip/bcm2836: Use a more generic memory barrier call
irqchip/bcm2836: Fix compiler warning on 64-bit build
irqchip/bcm2836: Drop smp_set_ops on arm64 builds
irqchip/gic: Add helper functions for GIC setup and teardown
irqchip/gic: Store GIC configuration parameters
irqchip/gic: Pass GIC pointer to save/restore functions
irqchip/gic: Return an error if GIC initialisation fails
irqchip/gic: Remove static irq_chip definition for eoimode1
irqchip/gic: Don't initialise chip if mapping IO space fails
irqchip/gic: WARN if setting the interrupt type for a PPI fails
irqchip/gic: Don't unnecessarily write the IRQ configuration
irqchip: Mask the non-type/sense bits when translating an IRQ
genirq: Ensure IRQ descriptor is valid when setting-up the IRQ
irqchip/gic-v3: Configure all interrupts as non-secure Group-1
irqchip/gic-v2m: Add workaround for Broadcom NS2 GICv2m erratum
irqchip/irq-alpine-msi: Don't use <asm-generic/msi.h>
irqchip/mbigen: Checking for IS_ERR() instead of NULL
irqchip/gic-v3: Remove inexistant register definition
irqchip/gicv3-its: Don't allow devices whose ID is outside range
irqchip: Add LPC32xx interrupt controller driver
...
|
|
Cut down on noise for mainstream users of the API and people doing build
testing by dropping the deprecated flag from regulator_can_change_voltage()
as it triggers even on the EXPORT_SYMBOL_GPL() which affects all builds
rather than just the remaining drivers with calls to it (for which fixes
are currently pending).
The function remains deprecated and is expected to be removed entirely
in v4.8.
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"A rather small set of patches from the timer departement:
- Some more y2038 work
- Yet another new clocksource driver
- The usual set of small fixes, cleanups and enhancements"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/tegra: Remove unused suspend/resume code
clockevents/driversi/mps2: add MPS2 Timer driver
dt-bindings: document the MPS2 timer bindings
clocksource/drivers/mtk_timer: Add __init attribute
clockevents/drivers/dw_apb_timer: Implement ->set_state_oneshot_stopped()
time: Introduce do_sys_settimeofday64()
security: Introduce security_settime64()
clocksource: Add missing include of of.h.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing ring-buffer fixes from Steven Rostedt:
"Hao Qin reported an integer overflow possibility with signed and
unsigned numbers in the ring-buffer code.
https://bugzilla.kernel.org/show_bug.cgi?id=118001
At first I did not think this was too much of an issue, because the
overflow would be caught later when either too much data was allocated
or it would trigger RB_WARN_ON() which shuts down the ring buffer.
But looking closer into it, I found that the right settings could
bypass the checks and crash the kernel. Luckily, this is only
accessible by root.
The first fix is to convert all the variables into long, such that we
don't get into issues between 32 bit variables being assigned 64 bit
ones. This fixes the RB_WARN_ON() triggering.
The next fix is to get rid of a duplicate DIV_ROUND_UP() that when
called twice with the right value, can cause a kernel crash.
The first DIV_ROUND_UP() is to normalize the input and it is checked
against the minimum allowable value. But then DIV_ROUND_UP() is
called again, which can overflow due to the (a + b - 1)/b, logic. The
first called upped the value, the second can overflow (with the +b
part).
The second call to DIV_ROUND_UP() came in via a second change a while
ago and the code is cleaned up to remove it"
* tag 'trace-fixes-v4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ring-buffer: Prevent overflow of size in ring_buffer_resize()
ring-buffer: Use long for nr_pages to avoid overflow failures
|
|
We saw the following extra refcount release on veth device:
kernel: [7957821.463992] unregister_netdevice: waiting for mesos50284 to become free. Usage count = -1
Since we heavily use mirred action to redirect packets to veth, I think
this is caused by the following race condition:
CPU0:
tcf_mirred_release(): (in RCU callback)
struct net_device *dev = rcu_dereference_protected(m->tcfm_dev, 1);
CPU1:
mirred_device_event():
spin_lock_bh(&mirred_list_lock);
list_for_each_entry(m, &mirred_list, tcfm_list) {
if (rcu_access_pointer(m->tcfm_dev) == dev) {
dev_put(dev);
/* Note : no rcu grace period necessary, as
* net_device are already rcu protected.
*/
RCU_INIT_POINTER(m->tcfm_dev, NULL);
}
}
spin_unlock_bh(&mirred_list_lock);
CPU0:
tcf_mirred_release():
spin_lock_bh(&mirred_list_lock);
list_del(&m->tcfm_list);
spin_unlock_bh(&mirred_list_lock);
if (dev) // <======== Stil refers to the old m->tcfm_dev
dev_put(dev); // <======== dev_put() is called on it again
The action init code path is good because it is impossible to modify
an action that is being removed.
So, fix this by moving everything under the spinlock.
Fixes: 2ee22a90c7af ("net_sched: act_mirred: remove spinlock in fast path")
Fixes: 6bd00b850635 ("act_mirred: fix a race condition on mirred_list")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The publication field of the old netlink API should contain the
publication key and not the publication reference.
Fixes: 44a8ae94fd55 (tipc: convert legacy nl name table dump to nl compat)
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto update from Herbert Xu:
"API:
- Crypto self tests can now be disabled at boot/run time.
- Add async support to algif_aead.
Algorithms:
- A large number of fixes to MPI from Nicolai Stange.
- Performance improvement for HMAC DRBG.
Drivers:
- Use generic crypto engine in omap-des.
- Merge ppc4xx-rng and crypto4xx drivers.
- Fix lockups in sun4i-ss driver by disabling IRQs.
- Add DMA engine support to ccp.
- Reenable talitos hash algorithms.
- Add support for Hisilicon SoC RNG.
- Add basic crypto driver for the MXC SCC.
Others:
- Do not allocate crypto hash tfm in NORECLAIM context in ecryptfs"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (77 commits)
crypto: qat - change the adf_ctl_stop_devices to void
crypto: caam - fix caam_jr_alloc() ret code
crypto: vmx - comply with ABIs that specify vrsave as reserved.
crypto: testmgr - Add a flag allowing the self-tests to be disabled at runtime.
crypto: ccp - constify ccp_actions structure
crypto: marvell/cesa - Use dma_pool_zalloc
crypto: qat - make adf_vf_isr.c dependant on IOV config
crypto: qat - Fix typo in comments
lib: asn1_decoder - add MODULE_LICENSE("GPL")
crypto: omap-sham - Use dma_request_chan() for requesting DMA channel
crypto: omap-des - Use dma_request_chan() for requesting DMA channel
crypto: omap-aes - Use dma_request_chan() for requesting DMA channel
crypto: omap-des - Integrate with the crypto engine framework
crypto: s5p-sss - fix incorrect usage of scatterlists api
crypto: s5p-sss - Fix missed interrupts when working with 8 kB blocks
crypto: s5p-sss - Use common BIT macro
crypto: mxc-scc - fix unwinding in mxc_scc_crypto_register()
crypto: mxc-scc - signedness bugs in mxc_scc_ablkcipher_req_init()
crypto: talitos - fix ahash algorithms registration
crypto: ccp - Ensure all dependencies are specified
...
|
|
For ethernet devices, net_device.name will be eth%d before
register_netdev() is called. Don't print the net_device name until
the format string is replaced.
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: Marcel Ziswiler <marcel@ziswiler.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Barry Song <Baohua.Song@csr.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the necessary driver support for Management Firmware to
configure the device/firmware with the dcbx results. Management Firmware
is responsible for communicating the DCBX and driving the negotiation,
but the driver has responsibility of receiving async notification and
configuring the results in hw/fw. This patch also adds the dcbx support for
future protocols (e.g., FCoE) as preparation to their imminent submission.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When reopening the network device on ra7795/salvator-x, e.g. after a
DHCP timeout:
IP-Config: Reopening network devices...
genirq: Flags mismatch irq 139. 00000000 (eth0:ch0:rx_be) vs. 00000000 (ravb e6800000.ethernet eth0: cannot request IRQ eth0:ch0:rx_be
IP-Config: Failed to open eth0
IP-Config: No network devices available
The "mismatch" is due to requesting an IRQ that is already in use,
while IRQF_PROBE_SHARED wasn't set.
However, the real cause is that ravb_close() doesn't release any of the
R-Car Gen3-specific secondary IRQs.
Add the missing free_irq() calls to fix this.
Fixes: f51bdc236b6c5835 ("ravb: Add dma queue interrupt support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This line was indented more than it should be.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-05-16
This series contains 2 fixes to ixgbe only.
Emil fixes transmit hangs when enabling SRIOV by swapping the parameters
in GENMASK in order to generate the correct mask.
Alex fixes his previous patch b83e30104bd9 ("ixgbe/ixgbevf: Add support
for GSO partial") where he somehow transposed the location of setting
the VLAN features in netdev->features and the configuration of the
vlan_features.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function setup_timer combines the initialization of a timer with the
initialization of the timer's function and data fields. The mulitiline
code for timer initialization is now replaced with function setup_timer.
Also, quoting the mod_timer() function comment:
-> mod_timer() is a more efficient way to update the expire field of an
active timer (if the timer is inactive it will be activated).
Use setup_timer() and mod_timer() to setup and arm a timer, making the
code compact and aid readablity.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
During boot, MST hotplugs are generally expected (even if no physical
hotplugging occurs) and result in DRM's connector topology changing.
This means that using num_connector from the current mode configuration
can lead to the number of connectors changing under us. This can lead to
some nasty scenarios in fbcon:
- We allocate an array to the size of dev->mode_config.num_connectors.
- MST hotplug occurs, dev->mode_config.num_connectors gets incremented.
- We try to loop through each element in the array using the new value
of dev->mode_config.num_connectors, and end up going out of bounds
since dev->mode_config.num_connectors is now larger then the array we
allocated.
fb_helper->connector_count however, will always remain consistent while
we do a modeset in fb_helper.
Note: This is just polish for 4.7, Dave Airlie's drm_connector
refcounting fixed these bugs for real. But it's good enough duct-tape
for stable kernel backporting, since backporting the refcounting
changes is way too invasive.
Cc: stable@vger.kernel.org
Signed-off-by: Lyude <cpaul@redhat.com>
[danvet: Clarify why we need this. Also remove the now unused "dev"
local variable to appease gcc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1463065021-18280-3-git-send-email-cpaul@redhat.com
|
|
During boot time, MST devices usually send a ton of hotplug events
irregardless of whether or not any physical hotplugs actually occurred.
Hotplugs mean connectors being created/destroyed, and the number of DRM
connectors changing under us. This isn't a problem if we use
fb_helper->connector_count since we only set it once in the code,
however if we use num_connector from struct drm_mode_config we risk it's
value changing under us. On top of that, there's even a chance that
dev->mode_config.num_connector != fb_helper->connector_count. If the
number of connectors happens to increase under us, we'll end up using
the wrong array size for memcpy and start writing beyond the actual
length of the array, occasionally resulting in kernel panics.
Note: This is just polish for 4.7, Dave Airlie's drm_connector
refcounting fixed these bugs for real. But it's good enough duct-tape
for stable kernel backporting, since backporting the refcounting
changes is way too invasive.
Cc: stable@vger.kernel.org
Signed-off-by: Lyude <cpaul@redhat.com>
[danvet: Clarify why we need this.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1463065021-18280-2-git-send-email-cpaul@redhat.com
|
|
next/cleanups-fixes
This is a merge of the cleanup and fixes-non-critical branches for the 4.7
merge window. It seems more appropriate to send a single pull request
for these than two separate ones, as both branches really contain both
fixes and cleanups.
* next/cleanup:
ARM: debug: remove extraneous DEBUG_HI3716_UART option
ARM: davinci: use IRQCHIP_DECLARE for cp_intc
ARM: davinci: remove unused DA8XX_NUM_UARTS
ARM: davinci: simplify call to of populate
ARM: DaVinci USB: removed deprecated properties from MUSB config
ARM: rockchip: Fix use of plain integer as NULL pointer
ARM: realview: hide unused 'pmu_device' object
soc: versatile: dynamically detect RealView HBI numbers
* next/fixes-non-critical:
ARM: dts: exynos: Add interrupt line to MAX8997 PMIC on exynos4210-trats
ARM: dts: exynos: Fix regulator name to avoid forbidden character on exynos4210-trats
ARM: dts: exynos: Add MFC memory banks for Peach boards
ARM: OMAP2+: n900 needs MMC slot names for legacy user space
ARM: OMAP2+: Add more functions to pwm pdata for ir-rx51
ARM: EXYNOS: Properly skip unitialized parent clock in power domain on
ARM: OMAP2+: Simplify auxdata by using the generic match
of/platform: Allow secondary compatible match in of_dev_lookup
|
|
|
|
|
|
|
|
|
|
The PWM states make it possible to also output the polarity, duty cycle
and period information in the debugfs summary output. This simplifies
gathering information about PWMs without needing to walk through the
sysfs attributes of every PWM.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[thierry.reding@gmail.com: use more spaces in debugfs output]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Replace legacy pwm_get/set_xxx() and pwm_config/enable/disable() calls
by pwm_get/apply_state().
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Update the PWM subsystem documentation to reflect the atomic PWM
changes.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Add an ->apply() method to the pwm_ops struct to allow PWM drivers to
implement atomic updates. This method is preferred over the ->enable(),
->disable() and ->config() methods if available.
Add the pwm_apply_state() function to the PWM user API.
Note that the pwm_apply_state() does not guarantee the atomicity of the
update operation, it all depends on the availability and implementation
of the ->apply() method.
pwm_enable/disable/set_polarity/config() are now implemented as wrappers
around the pwm_apply_state() function.
pwm_adjust_config() is allowing smooth handover between the bootloader
and the kernel. This function tries to adapt the current PWM state to
the PWM arguments coming from a PWM lookup table or a DT definition
without changing the duty_cycle/period proportion.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[thierry.reding@gmail.com: fix a couple of typos]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Add a ->get_state() function to the pwm_ops struct to let PWM drivers
initialize the PWM state attached to a PWM device.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Prepare the transition to PWM atomic update by moving the enabled and
disabled state into the pwm_state struct. This way we can easily update
the whole PWM state by copying the new state in the ->state field.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The PWM state, represented by its period, duty_cycle and polarity is
currently directly stored in the PWM device. Declare a pwm_state
structure embedding those field so that we can later use this struct
to atomically update all the PWM parameters at once.
All pwm_get_xxx() helpers are now implemented as wrappers around
pwm_get_state().
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Before the introduction of pwm_args, the core was resetting the PWM
period and polarity states to the reference values (those provided
through the DT, a PWM lookup table or hardcoded in the driver).
Now that all PWM users are correctly using pwm_args to configure their
PWM device, we can safely remove the pwm_apply_args() call in pwm_get()
and of_pwm_get().
We can also get rid of the pwm_set_period() call in pwm_apply_args(),
because PWM users are now directly using pargs->period instead of
pwm_get_period(). By doing that we avoid messing with the current PWM
period.
The only remaining bit in pwm_apply_args() is the initial polarity
setting, and it should go away when all PWM users have been patched to
use the atomic API (with this API the polarity will be set along with
other PWM arguments when configuring the PWM).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Call pwm_apply_args() just after requesting the PWM device so that the
polarity and period are initialized according to the information
provided in pwm_args.
This is an intermediate state, and pwm_apply_args() should be dropped as
soon as the atomic PWM infrastructure is in place and the driver makes
use of it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Call pwm_apply_args() just after requesting the PWM device so that the
polarity and period are initialized according to the information
provided in pwm_args.
This is an intermediate state, and pwm_apply_args() should be dropped as
soon as the atomic PWM infrastructure is in place and the driver makes
use of it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Call pwm_apply_args() just after requesting the PWM device so that the
polarity and period are initialized according to the information
provided in pwm_args.
This is an intermediate state, and pwm_apply_args() should be dropped as
soon as the atomic PWM infrastructure is in place and the driver makes
use of it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Call pwm_apply_args() just after requesting the PWM device so that the
polarity and period are initialized according to the information
provided in pwm_args.
This is an intermediate state, and pwm_apply_args() should be dropped as
soon as the atomic PWM infrastructure is in place and the driver makes
use of it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Call pwm_apply_args() just after requesting the PWM device so that the
polarity and period are initialized according to the information
provided in pwm_args.
This is an intermediate state, and pwm_apply_args() should be dropped as
soon as the atomic PWM infrastructure is in place and the driver makes
use of it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Call pwm_apply_args() just after requesting the PWM device so that the
polarity and period are initialized according to the information
provided in pwm_args.
This is an intermediate state, and pwm_apply_args() should be dropped as
soon as the atomic PWM infrastructure is in place and the driver makes
use of it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Call pwm_apply_args() just after requesting the PWM device so that the
polarity and period are initialized according to the information
provided in pwm_args.
This is an intermediate state, and pwm_apply_args() should be dropped as
soon as the atomic PWM infrastructure is in place and the driver makes
use of it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The PWM framework has clarified the concept of reference PWM config (the
platform dependent config retrieved from the DT or the PWM lookup table)
and real PWM state.
Use pwm_get_args() when the PWM user wants to retrieve this reference
config and not the current state.
This is part of the rework allowing the PWM framework to support
hardware readout and expose real PWM state even when the PWM has just
been requested (before the user calls pwm_config/enable/disable()).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The PWM framework has clarified the concept of reference PWM config (the
platform dependent config retrieved from the DT or the PWM lookup table)
and real PWM state.
Use pwm_get_args() when the PWM user wants to retrieve this reference
config and not the current state.
This is part of the rework allowing the PWM framework to support
hardware readout and expose real PWM state even when the PWM has just
been requested (before the user calls pwm_config/enable/disable()).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The PWM framework has clarified the concept of reference PWM config (the
platform dependent config retrieved from the DT or the PWM lookup table)
and real PWM state.
Use pwm_get_args() when the PWM user wants to retrieve this reference
config and not the current state.
This is part of the rework allowing the PWM framework to support
hardware readout and expose real PWM state even when the PWM has just
been requested (before the user calls pwm_config/enable/disable()).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The PWM framework has clarified the concept of reference PWM config (the
platform dependent config retrieved from the DT or the PWM lookup table)
and real PWM state.
Use pwm_get_args() when the PWM user wants to retrieve this reference
config and not the current state.
This is part of the rework allowing the PWM framework to support
hardware readout and expose real PWM state even when the PWM has just
been requested (before the user calls pwm_config/enable/disable()).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The PWM framework has clarified the concept of reference PWM config (the
platform dependent config retrieved from the DT or the PWM lookup table)
and real PWM state.
Use pwm_get_args() when the PWM user wants to retrieve this reference
config and not the current state.
This is part of the rework allowing the PWM framework to support
hardware readout and expose real PWM state even when the PWM has just
been requested (before the user calls pwm_config/enable/disable()).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The PWM framework has clarified the concept of reference PWM config (the
platform dependent config retrieved from the DT or the PWM lookup table)
and real PWM state.
Use pwm_get_args() when the PWM user wants to retrieve this reference
config and not the current state.
This is part of the rework allowing the PWM framework to support
hardware readout and expose real PWM state even when the PWM has just
been requested (before the user calls pwm_config/enable/disable()).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The PWM framework has clarified the concept of reference PWM config (the
platform dependent config retrieved from the DT or the PWM lookup table)
and real PWM state.
Use pwm_get_args() when the PWM user wants to retrieve this reference
config and not the current state.
This is part of the rework allowing the PWM framework to support
hardware readout and expose real PWM state even when the PWM has just
been requested (before the user calls pwm_config/enable/disable()).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Use pwm_get/set_xxx() helpers instead of directly accessing the pwm->xxx
field. Doing that will ease adaptation of the PWM framework to support
atomic update.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
PWM devices are not protected against concurrent accesses. The lock in
struct pwm_device might let PWM users think it is, but it's actually
only protecting the enabled state.
Removing this lock should be fine as long as all PWM users are aware
that accesses to the PWM device have to be serialized, which seems to be
the case for all of them except the sysfs interface. Patch the sysfs
code by adding a lock to the pwm_export struct and making sure it's
taken for all relevant accesses to the exported PWM device.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
pwm->period field is not supposed to be changed by PWM users. The only
ones authorized to change it are the PWM core and PWM drivers.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The PWM period will be set when calling pwm_config. Remove this useless
call to pwm_set_period(), which might mess up the internal PWM state.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
