| Age | Commit message (Collapse) | Author |
|---|
|
In the standalone setup the board's CPLD disables the PCI internal
arbiter, thus any access to the PCI bus will hang the board.
The common way to disable particular devices in the device tree is to
put the "status" property with any value other than "ok" or "okay"
into the device node we want to disable.
So, when there is no PCI arbiter on the bus the u-boot adds status =
"broken (no arbiter)" property into the PCI controller's node, and so
marks the PCI controller as unavailable.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Specifying user-selectable option in the qe_lib/Kconfig was a bad idea
because the qe_lib/Kconfig is included into the top level Kconfig, and
thus the QE_GPIO option appears at the top level menu.
This patch effectively moves the QE_GPIO option under the platform menu
instead.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Modify the Kconfig so that Freescale QUICC Engine (QE) support is a selectable
option, thereby allowing users to compile kernels without any QE support.
The drawback is that QE support is now disabled by default on platforms that
have a QE, and so a defconfig is needed to enable QE and QE devices (like
UCC GETH). Fortunately, all the current relevant defconfigs do that already.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC MPC8641D).
A number of MPC8641D based route interrupts for on-board interrupts through
a FPGA based interrupt controller, which is chained with the
MPC8641D's mpic. This patch provides a basic driver to allow basic routing
of interrupts to the mpic.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add interrupt info to the MPC8536DS .dts for the RTC
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
and generates a page fault
Arjan reported a spike in the following bug pattern in v2.6.27:
http://www.kerneloops.org/searchweek.php?search=lock_page
which happens because hwclock started triggering warnings due to
a (correct) might_sleep() check in the MM code.
The warning occurs because hwclock uses this dubious sequence of
code to run "atomic" code:
static unsigned long
atomic(const char *name, unsigned long (*op)(unsigned long),
unsigned long arg)
{
unsigned long v;
__asm__ volatile ("cli");
v = (*op)(arg);
__asm__ volatile ("sti");
return v;
}
Then it pagefaults in that "atomic" section, triggering the warning.
There is no way the kernel could provide "atomicity" in this path,
a page fault is a cannot-continue machine event so the kernel has to
wait for the page to be filled in.
Even if it was just a minor fault we'd have to take locks and might have
to spend quite a bit of time with interrupts disabled - not nice to irq
latencies in general.
So instead just enable interrupts in the pagefault path unconditionally
if we come from user-space, and handle the fault.
Also, while touching this code, unify some trivial parts of the x86
VM paths at the same time.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Use new MODULE_DEVICE_TABLE(dmi, ...) facility. There's no need for
every driver to screw it up for themselves, when the alias can be
generated automatically.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This makes modpost handle MODULE_DEVICE_TABLE(dmi, xxxx).
I had to change the string pointers in the match table to char arrays,
and picked a size of 79 bytes almost at random -- do we need to make it
bigger than that? I was a bit concerned about the 'bloat' this
introduces into the match tables, but they should all be __initdata so
it shouldn't matter too much.
(Actually, modpost does go through the relocations and look at most of
them; it wouldn't be impossible to make it handle string pointers -- but
doesn't seem to be worth the effort, since they're __initdata).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Added support for Prof 7300 DVB-S/S2 card. The card
based on cx24116 demodulator.
Signed-off-by: Oleg Roitburd <oroitburd@gmail.com>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
[mchehab@redhat.com: fixed CARDLIST.cx88 entry]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
MEI are renaming themselves to Panasonic, so update the MAINTAINERS
record for the MN10300 arch.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Non-initialised cache values get a reasonble default.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
default.
cx24116: Change the default SNR units back to percentage by default.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
S2API: Return error of the caller provides 0 commands.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
A user tuning DVB-T via the S2API reports that this was not implemented,
and his tuning was failing.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
DTV_TRANSMISSION_MODE
Tuning DVB-T via the S2API was failing, missing some essential items.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Reports from users that using the new API for tuning DTV was failing,
and the cache was missing some essential items.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Reviewing the code briefly and saw this.
You can't change more than DTV_IOCTL_MAX_MSGS at once, not 16.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
I've retained the older percentage code after discussing this with
Darron Broad, but made the ESNO option default.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
... and cleanup any drivers using them.
I've also removed NBC_QPSK and modified the cx24116 driver to check
the delivery_type also, removing some excess namespace baggage.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add support for DvbWorld USB cards with STV0288 demodulator.
Those cards use Earda EDS-1547 tuner.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Remove NULL pointer in stb6000 driver,
as it raises error for DvbWorld USB card.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Allow custom inittab for ST STV0288 demodulator,
as it is needed for DvbWorld USB card.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This means that when developers add new commands then they'll be see
the DTV_MAX_COMMAND define and will be more likely to modify it, without
having to modify the command validation code.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
legacy API.
Fixes switching from S2API to legacy where legacy params given to S2API
aware demods are cached ones and not those implied in the legacy API.
It was found (on an S2API aware demod at least) that after using
an S2API aware application and then switching to a legacy application
that prior S2API params were in effect were legacy has only
implied values. This fixes this.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Quick fix to stop an OOPS if illegal commands are dumped in S2API.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
cx24116 demod.
Add some sanity checking to data input via S2API to the cx24116 demod.
This patch is valid for both s2-mfe and s2.
It was found when testing KAFFEINE with S2API support that invalid
modulation modes amongst other parameters were being delivered to
the demod. In order to debug this sanity checking has been added.
An example session would involve kaffeine setting QAM_AUTO when
querying DVB-T, then later when trying to tune to DVB-S this
cached value would be presented in error.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This adds required quirks for the Compaq Presario B1200 and Acer Travelmate
7720 integrated webcams.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
We must be using the bh spin locking functions in
iscsi_eh_device_reset becuase the session lock interacts with
a thread and softirq.
This patch also fixes up a bogus comment and check in fail_command,
because no one drops the lock (bnx2i did but it is not going
upstream yet and there were other refcount changes for that).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
value
Some wires got crossed on some patches and I messed up in the code
below when rebuilding a patch. We want to be checking if flag
equaled the value indicating if we killing the session due to
final logout or if we just trying to relogin.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The segment->done functions return a iscsi error value which gives
a lot more info than conn failed, so this patch has us return
that value. I also add a new one for xmit failures.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
I had this in my patchset to add target reset support, but
it got dropped due to patching conflicts. This initial patch
just renames the function and users. We are actually just
dropping the session, and so this does not have anything to do
with the host exactly. It does for software iscsi because
we allocate a host per session, but for cxgb3i this makes no
sense.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Some endpoint code was using unsigned int and some
was using uint64_t. This converts it all to uint64_t.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
If the driver knows when hardware is removed like with cxgb3i,
bnx2i, qla4xxx and iser then we will want to remove the sessions/devices
that are bound to that device before removing the host.
cxgb3i and in the future bnx2i will remove the host and that will
remove all the sessions on the hba. iser can call iscsi_kill_session
when it gets an event that indicates that a hca is removed.
And when qla4xxx is hooked in to the lib (it is only hooked into
the class right now) it can call iscsi remove host like the
partial offload card drivers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
iscsi_tcp was updating the exp_statsn (exp_statsn acknowledges
status and tells the target it is ok to let the resources for
a iscsi pdu to be reused) before it got all the data for pdu read
into OS buffers. Data corruption was occuring if something happens
to a packet and the network layer requests a retransmit, and the
initiator has told the target about the udpated exp_statsn ack,
then the target may be sending data from a buffer it has reused
for a new iscsi pdu. This fixes the problem by having the LLD
(iscsi_tcp in this case) just handle the transferring of data, and
has libiscsi handle the processing of status (libiscsi completion
processing is done after LLD data transfers are complete).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
For some reason these messages ended up being printed with KERN_INFO
rendering them invisible to pretty much everyone. Switch to
KERN_NOTICE.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The old detection code couldn't handle all possible combinations of
DIX and DIF. This version does, giving priority to DIX if the
controller is capable.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Now that we no longer use protection_type as trigger for preparing
protected CDBs we can remove the places that set it to zero. This
allows userland to see which protection type the device is formatted
with regardless of whether the HBA supports DIF or not.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Use the same logic to prepare RD/WRPROTECT and the protection
operation. Fixes a corner case where we could issue an unprotected
CDB and yet tell the HBA to do DIF to the drive.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
There's a target reset bug.
This loop:
for (id = 0; id <= shost->max_id; id++) {
Never terminates if shost->max_id is set to ~0, like aic94xx does.
It's also pretty inefficient since you mostly have compact target
numbers, but the max_id can be very high. The best way would be to
sort the recovery list by target id and skip them if they're equal,
but even a worst case O(N^2) traversal is probably OK here, so fix it
by finding the next highest target number (assuming n+1) and
terminating when there isn't one.
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
vendor events
Added support for new sysfs attributes: lpfc_stat_data_ctrl and
lpfc_max_scsicmpl_time. The attributes control statistical reporting
of io load.
Added support for new fc vendor events for error reporting.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Added new sysfs attribute lpfc_max_scsicmpl_time. Attribute, when enabled,
will control target queue depth based on I/O completion time.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Revert the target busy response in favor of the transport disrupted
response for node state transitions.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
We do not need to set REQ_NOMERGE because when the module calls
blk_execute_rq -> blk_execute_rq_nowait, blk_execute_rq_nowait sets
it for us. This brings all the modules in sync for those bits.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Add support for MSI-X Multi-Message interrupts. We use different vectors
for fast-path interrupts (i/o) and slow-patch interrupts (discovery, etc).
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
DID_TRANSPORT_DISRUPTED
[jejb: drop rejecting hunk altered by target busy patches]
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Add support for PCI-EEH permanent-disabling a device via lpfc_pci_remove_one()
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Miscellaneous Fixes:
- Fix the wrong variable name used for checking node active usage status
- Fix numerous duplicate log message numbers
- Fix change KERN_WARNING messages to KERN_INFO.
- Stop sending erroneous LOGO to fabric after vport is already terminated
- Fix HBQ allocates that were kalloc'ing w/ GFP_KERNEL while holding a lock.
- Fix gcc 4.3.2 compiler warnings and a sparse warning
- Fix bugs in handling unsolicited ct event queue
- Reorder some of the initial link up checks, to remove odd VPI states.
- Correct poor VPI handling
- Add debug messages
- Expand Update_CFG mailbox definition
- Fix handling of VPD data offsets
- Reorder loopback flags
- convert to use offsetof()
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
