| Age | Commit message (Collapse) | Author |
|---|
|
Trivial fix to spelling mistake "configutation" to "configuration"
in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
cec_read() is non-atomic in the presence of other I2C bus transactions
to the same device. This presents a problem when we add support for
the TDA9950 CEC engine part - both drivers can be trying to access the
device.
Avoid the inherent problems by switching to i2c_transfer() instead,
which allows us to perform more than one bus transaction atomically.
As this means we will be using I2C transactions rather than SMBUS, we
have to check that the host supports I2C functionality.
Tested-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Some TDA998x contain several different I2C devices - there is the HDMI
encoder, and there is a TDA9950 CEC engine. These two share the same
interrupt signal.
In order to allow a driver for the CEC engine to work, we need to be
able to share the interrupt with the CEC driver, so convert the handler
and registration to allow this to happen.
Tested-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Disabling the pre-filter block of the TDA998x saves 40mW and the colour
conversion block saves 15mW. As we always disable these two blocks, we
can power these sections of the chip down to save 55mW of unnecessary
power consumption.
Tested-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Rather than storing the DPMS mode (which will always be on or off) use a
boolean to store this instead.
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
tda998x_audio_get_eld() is needlessly complex - the connector associated
with the encoder is always our own priv->connector. Remove this
complexity, but ensure that there are no races when copying out the ELD.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Group the TDA998x audio functions together rather than split between
two different locations in the file, keeping like code together.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Separate out the connector initialisation from the rest of the drivers
initialisation.
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Group the TDA998x connector functions and funcs structures together
before the encoder support, rather than scattered amongst the rest of
the file. This keeps like code together.
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The naming of tda998x_encoder_set_config() is a left-over from when
TDA998x was a slave encoder. Since this is part of the initialisation,
drop the _encoder from the name, and move it near tda998x_bind().
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Correct two references to tda998x_connector_get_modes() which were
incorrectly referring to tda998x_encoder_get_modes().
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Check for audio support by the attached sink by consulting the EDID
prior to enabling audio over the TMDS link. We must consult the EDID
after calling drm_helper_probe_single_connector_modes(), as this can
use an override EDID, or load a replacement EDID.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The CEA 861B specification indicates the situations when we are able to
send each infoframe based on the version of the EDID's CEA extension.
Update the tda998x driver to follow the CEA specification wrt sending
of infoframes.
Since we only support the generation of AVI version 2, this limits us
to CEA extension version 3, so we treat CEA extension version 2 as
CEA 861 (no infoframes, no audio.)
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Avoid a race between programming audio and an in-progress mode set.
A mode set is complex, and disables the ability to send infoframes
to the sink, and is disruptive to audio - we have to mute the audio
FIFO while doing a mode set.
If an attempt is made to start up the audio side, we will undo the
audio FIFO mute before the mode set has completed.
Move the lock so that we prevent audio interfering with an in-progress
mode set.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Avoid a racy access to the mode clock by storing the current mode clock
during a mode set under the audio mutex. This allows us to access it
from the audio path in a safe way.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
As priv->audio_params can now be changed at run time, we need to be more
careful about how we deal with a mode set. We must take the audio lock
while checking if there's a valid audio configuration.
However, it's slightly worse than that - during mode set, we mute the
audio, and it must not be unmuted until we have finished the mode set.
It is possible that the audio side may start while a mode set is in
progress, so take the audio_mutex lock around the whole mode setting
procedure.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
We will need the audio mutex initialised in all cases, so lets move this
to be early, rather than only being initialised for the DT case.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Pull block fixes from Jens Axboe:
"A set of fixes, one for NVMe from Keith, and a set for nvme-{rdma,t,f}
from the usual suspects, fixing actual problems that would be a shame
to release 4.9 with"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvme/pci: Don't free queues on error
nvmet-rdma: drain the queue-pair just before freeing it
nvme-rdma: stop and free io queues on connect failure
nvmet-rdma: don't forget to delete a queue from the list of connection failed
nvmet: Don't queue fatal error work if csts.cfs is set
nvme-rdma: reject non-connect commands before the queue is live
nvmet-rdma: Fix possible NULL deref when handling rdma cm events
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rmda fixes from Doug Ledford.
"First round of -rc fixes.
Due to various issues, I've been away and couldn't send a pull request
for about three weeks. There were a number of -rc patches that built
up in the meantime (some where there already from the early -rc
stages). Obviously, there were way too many to send now, so I tried to
pare the list down to the more important patches for the -rc cycle.
Most of the code has had plenty of soak time at the various vendor's
testing setups, so I doubt there will be another -rc pull request this
cycle. I also tried to limit the patches to those with smaller
footprints, so even though a shortlog is longer than I would like, the
actual diffstat is mostly very small with the exception of just three
files that had more changes, and a couple files with pure removals.
Summary:
- Misc Intel hfi1 fixes
- Misc Mellanox mlx4, mlx5, and rxe fixes
- A couple cxgb4 fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (34 commits)
iw_cxgb4: invalidate the mr when posting a read_w_inv wr
iw_cxgb4: set *bad_wr for post_send/post_recv errors
IB/rxe: Update qp state for user query
IB/rxe: Clear queue buffer when modifying QP to reset
IB/rxe: Fix handling of erroneous WR
IB/rxe: Fix kernel panic in UDP tunnel with GRO and RX checksum
IB/mlx4: Fix create CQ error flow
IB/mlx4: Check gid_index return value
IB/mlx5: Fix NULL pointer dereference on debug print
IB/mlx5: Fix fatal error dispatching
IB/mlx5: Resolve soft lock on massive reg MRs
IB/mlx5: Use cache line size to select CQE stride
IB/mlx5: Validate requested RQT size
IB/mlx5: Fix memory leak in query device
IB/core: Avoid unsigned int overflow in sg_alloc_table
IB/core: Add missing check for addr_resolve callback return value
IB/core: Set routable RoCE gid type for ipv4/ipv6 networks
IB/cm: Mark stale CM id's whenever the mad agent was unregistered
IB/uverbs: Fix leak of XRC target QPs
IB/hfi1: Remove incorrect IS_ERR check
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of regression fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix iov_iter_advance() for ITER_PIPE
xattr: Fix setting security xattrs on sockfs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux
Pull orangefs fix from Mike Marshall:
"orangefs: add .owner to debugfs file_operations
Without ".owner = THIS_MODULE" it is possible to crash the kernel by
unloading the Orangefs module while someone is reading debugfs files"
* tag 'for-linus-4.9-rc5-ofs-1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
orangefs: add .owner to debugfs file_operations
|
|
We need to clean up the global_timeline in i915_gem_load_cleanup.
v2: don't forget about the struct_mutex, and also WARN_ON if we have any
remaining timelines before purging the global_timeline.
v3: it might be a good idea to first remove the global_timeline...duh!
Fixes: 73cb97010d4f ("drm/i915: Combine seqno + tracking into a global timeline struct")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1479415087-13216-1-git-send-email-matthew.auld@intel.com
Link: http://patchwork.freedesktop.org/patch/msgid/20161117210411.14044-2-chris@chris-wilson.co.uk
|
|
We already have an i915_address_space_init, so for symmetry we should
also have a _fini, plus we already open code it twice. This then also
fixes a bug where we leak the timeline for the ggtt vm.
v2: don't forget about the struct_mutex for the ggtt path.
Fixes: 80b204bce8f2 ("drm/i915: Enable multiple timelines")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20161117210411.14044-1-chris@chris-wilson.co.uk
|
|
We should never be called via obj->ops->release() on anything other than
a fully formed stolen object, so raise that to an assert. In the process
tidy up a comment and variable no longer used outside of a conditional
BUG.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20161117155846.4631-1-chris@chris-wilson.co.uk
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
|
|
Userland client should be able to read an event, and reflect it back to
the kernel, therefore it needs to extract complete set of netlink flags.
For example, this will allow "tc monitor" to distinguish Add and Replace
operations.
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prior to 3.15, there was a race between zap_pte_range() and
page_mkclean() where writes to a page could be lost. Dave Hansen
discovered by inspection that there is a similar race between
move_ptes() and page_mkclean().
We've been able to reproduce the issue by enlarging the race window with
a msleep(), but have not been able to hit it without modifying the code.
So, we think it's a real issue, but is difficult or impossible to hit in
practice.
The zap_pte_range() issue is fixed by commit 1cf35d47712d("mm: split
'tlb_flush_mmu()' into tlb flushing and memory freeing parts"). And
this patch is to fix the race between page_mkclean() and mremap().
Here is one possible way to hit the race: suppose a process mmapped a
file with READ | WRITE and SHARED, it has two threads and they are bound
to 2 different CPUs, e.g. CPU1 and CPU2. mmap returned X, then thread
1 did a write to addr X so that CPU1 now has a writable TLB for addr X
on it. Thread 2 starts mremaping from addr X to Y while thread 1
cleaned the page and then did another write to the old addr X again.
The 2nd write from thread 1 could succeed but the value will get lost.
thread 1 thread 2
(bound to CPU1) (bound to CPU2)
1: write 1 to addr X to get a
writeable TLB on this CPU
2: mremap starts
3: move_ptes emptied PTE for addr X
and setup new PTE for addr Y and
then dropped PTL for X and Y
4: page laundering for N by doing
fadvise FADV_DONTNEED. When done,
pageframe N is deemed clean.
5: *write 2 to addr X
6: tlb flush for addr X
7: munmap (Y, pagesize) to make the
page unmapped
8: fadvise with FADV_DONTNEED again
to kick the page off the pagecache
9: pread the page from file to verify
the value. If 1 is there, it means
we have lost the written 2.
*the write may or may not cause segmentation fault, it depends on
if the TLB is still on the CPU.
Please note that this is only one specific way of how the race could
occur, it didn't mean that the race could only occur in exact the above
config, e.g. more than 2 threads could be involved and fadvise() could
be done in another thread, etc.
For anonymous pages, they could race between mremap() and page reclaim:
THP: a huge PMD is moved by mremap to a new huge PMD, then the new huge
PMD gets unmapped/splitted/pagedout before the flush tlb happened for
the old huge PMD in move_page_tables() and we could still write data to
it. The normal anonymous page has similar situation.
To fix this, check for any dirty PTE in move_ptes()/move_huge_pmd() and
if any, did the flush before dropping the PTL. If we did the flush for
every move_ptes()/move_huge_pmd() call then we do not need to do the
flush in move_pages_tables() for the whole range. But if we didn't, we
still need to do the whole range flush.
Alternatively, we can track which part of the range is flushed in
move_ptes()/move_huge_pmd() and which didn't to avoid flushing the whole
range in move_page_tables(). But that would require multiple tlb
flushes for the different sub-ranges and should be less efficient than
the single whole range flush.
KBuild test on my Sandybridge desktop doesn't show any noticeable change.
v4.9-rc4:
real 5m14.048s
user 32m19.800s
sys 4m50.320s
With this commit:
real 5m13.888s
user 32m19.330s
sys 4m51.200s
Reported-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If an ip6 tunnel is configured to inherit the traffic class from
the inner header, the dst_cache must be disabled or it will foul
the policy routing.
The issue is apprently there since at leat Linux-2.6.12-rc2.
Reported-by: Liam McBirnie <liam.mcbirnie@boeing.com>
Cc: Liam McBirnie <liam.mcbirnie@boeing.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Johan Hovold says:
====================
net: phy: fix of_node and device leaks
These patches fix a couple of of_node leaks in the fixed-link code and a
device reference leak in a phy helper.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the of_node reference taken in fixed_phy_register()
when deregistering a PHY.
Fixes: a75951217472 ("net: phy: extend fixed driver with
fixed_phy_register()")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the reference taken by bus_find_device() before
returning NULL from of_phy_find_device() when the found device is not a
PHY.
Fixes: 6ed742363b9c ("of: of_mdio: Ensure mdio device is a PHY")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the of_node reference also on failure to parse the
speed property in of_phy_register_fixed_link().
Fixes: 3be2a49e5c08 ("of: provide a binding for fixed link PHYs")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andrei reports we still allocate netns ID from idr after we destroy
it in cleanup_net().
cleanup_net():
...
idr_destroy(&net->netns_ids);
...
list_for_each_entry_reverse(ops, &pernet_list, list)
ops_exit_list(ops, &net_exit_list);
-> rollback_registered_many()
-> rtmsg_ifinfo_build_skb()
-> rtnl_fill_ifinfo()
-> peernet2id_alloc()
After that point we should not even access net->netns_ids, we
should check the death of the current netns as early as we can in
peernet2id_alloc().
For net-next we can consider to avoid sending rtmsg totally,
it is a good optimization for netns teardown path.
Fixes: 0c7aecd4bde4 ("netns: add rtnl cmd to add and get peer netns ids")
Reported-by: Andrei Vagin <avagin@gmail.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have to make sure there are no holes in the table in Gen9.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1479388435-12062-1-git-send-email-tvrtko.ursulin@linux.intel.com
|
|
Now with musb driver implementing generic session bit based
PM, we need to have the USB PHYs behaving in a sane way for
platforms implementing PM.
Currently twl4030-usb enables PM in twl4030_phy_power_on()
and then disables it in twl4030_phy_power_off(). This will
block PM runtime for the SoC when no cable is connected.
Fix the issue by moving PM runtime autosuspend call to
happen where it gets called in twl4030_phy_power_on().
Note that this patch should not be backported to anything
before commit 467d5c980709 ("usb: musb: Implement session bit
based runtime PM for musb-core") as before that all the
glue layers implemented their own PM.
Fixes: 467d5c980709 ("usb: musb: Implement session bit based
runtime PM for musb-core")
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This already gets done automatically by PM runtime and we have
a separate autosuspend timeout in musb_core.c.
Reviewed-by: Johan Hovold <johan@kernel.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We are missing pm_runtime_disable() in 2430 glue layer. Further,
we only need to enable PM runtime and disable it on exit. With
musb_core.c doing PM, the glue layer as a parent will always be
active when musb_core.c is active.
This fixes host enumeration issues with some devices as reported
by Ladislav Michl <ladis@linux-mips.org>.
And holding an RPM reference while deregistering the child would
lead to a crash in omap2430_runtime_suspend() which dereferences
the now freed child's driver data on put as pointed out by
Johan Hovold <johan@kernel.org>:
Unable to handle kernel paging request at virtual address 6b6b6f17
...
[<c05453d4>] (omap2430_runtime_suspend) from [<c0481410>]
(pm_generic_runtime_suspend+0x3c/0x48)
[<c0481410>] (pm_generic_runtime_suspend) from [<c0121028>]
(_od_runtime_suspend+0x1c/0x30)
[<c0121028>] (_od_runtime_suspend) from [<c04833b0>] (__rpm_callback+0x3c/0x70)
[<c04833b0>] (__rpm_callback) from [<c0483414>] (rpm_callback+0x30/0x90)
[<c0483414>] (rpm_callback) from [<c0483984>] (rpm_suspend+0x118/0x6b4)
[<c0483984>] (rpm_suspend) from [<c04840f4>] (rpm_idle+0x104/0x440)
[<c04840f4>] (rpm_idle) from [<c04844ac>] (__pm_runtime_idle+0x7c/0xb0)
[<c04844ac>] (__pm_runtime_idle) from [<c0545458>] (omap2430_remove+0x38/0x58)
[<c0545458>] (omap2430_remove) from [<c047b2bc>] (platform_drv_remove+0x34/0x4c)
Note that if changes are needed to the autosuspend timeout, it should
be done in musb_core.c.
Reported-by: Ladislav Michl <ladis@linux-mips.org>
Fixes: 87326e858448 ("usb: musb: Remove extra PM runtime calls from
2430 glue layer")
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With a USB hub disconnected, devctl can be 0x19 for about a second
on am335x and will stay forever on at least omap3. And we get no
further interrupts when devctl session bit clears. This keeps
PM runtime active.
Let's fix the issue by polling devctl until the session bit clears
or times out. We can do this by making musb->irq_work into
delayed_work.
And with the polling implemented, we can now also have the quirk
for invalid VBUS it to avoid disconnecting too early while VBUS
is ramping up.
Fixes: 467d5c980709 ("usb: musb: Implement session bit based runtime
PM for musb-core")
Fixes: 65b3f50ed6fa ("usb: musb: Add PM runtime support for MUSB DSPS
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 65b3f50ed6fa ("usb: musb: Add PM runtime support for MUSB DSPS
glue layer") wrongly added a call for pm_runtime_get_sync to otg_timer
that runs in softirq context. That causes a "BUG: sleeping function called
from invalid context" every time when polling the cable status:
[<c015ebb4>] (__might_sleep) from [<c0413d60>] (__pm_runtime_resume+0x9c/0xa0)
[<c0413d60>] (__pm_runtime_resume) from [<c04d0bc4>] (otg_timer+0x3c/0x254)
[<c04d0bc4>] (otg_timer) from [<c0191180>] (call_timer_fn+0xfc/0x41c)
[<c0191180>] (call_timer_fn) from [<c01915c0>] (expire_timers+0x120/0x210)
[<c01915c0>] (expire_timers) from [<c0191acc>] (run_timer_softirq+0xa4/0xdc)
[<c0191acc>] (run_timer_softirq) from [<c010168c>] (__do_softirq+0x12c/0x594)
I did not notice that as I did not have CONFIG_DEBUG_ATOMIC_SLEEP enabled.
And looks like also musb_gadget_queue() suffers from the same problem.
Let's fix the issue by using a list of delayed work then call it on
resume. Note that we want to do this only when musb core and it's
parent devices are awake, and we need to make sure the DSPS glue
timer is stopped as noted by Johan Hovold <johan@kernel.org>.
Note that we already are re-enabling the timer with mod_timer() in
dsps_musb_enable().
Later on we may be able to remove other delayed work in the musb driver
and just do it from pending_resume_work. But this should be done only
for delayed work that does not have other timing requirements beyond
just being run on resume.
Fixes: 65b3f50ed6fa ("usb: musb: Add PM runtime support for MUSB DSPS
glue layer")
Reported-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We can't use static variable first for checking when musb is
initialized when we have multiple musb instances like on am335x.
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Similar to existing yesno and onoff and use it throughout the code.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479385814-2358-2-git-send-email-tvrtko.ursulin@linux.intel.com
|
|
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
Kernel pointer does not sound like an useful thing to log and
pipe name is already contained in the crtc name.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
And also only dump DP config for crtcs with DP encoders.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
We don't spam the debug when we create a normal object, nor when we
allocate their pages. Yet we do for stolen objects, and since these are
quite frequently used (at least once per context), the resulting spam
floods the dmesg in CI.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
We use DRM_DEBUG() when reporting on user actions, to try and keep
intentional errors out of the CI dmesg. Demote the debug from
i915_gem_open() similarly so that it is only apparent with drm.debug & 1
like its brethren.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20161109104507.21228-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
Building the caam driver on arm64 produces a harmless warning:
drivers/crypto/caam/caamalg.c:140:139: warning: comparison of distinct pointer types lacks a cast
We can use min_t to tell the compiler which type we want it to use
here.
Fixes: 5ecf8ef9103c ("crypto: caam - fix sg dump")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
It looks to me skl_update_scaler will already log interesting
debug messages when the state transitions or there is an error.
In this case it feels we can remove the two unconditional
debug messages which happen immediately before calling
skl_update_scaler. This way we get rid of the sole debug
message when switching virtual terminals for example.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479376805-5087-1-git-send-email-tvrtko.ursulin@linux.intel.com
|
