| Age | Commit message (Collapse) | Author |
|---|
|
struct atomisp device has struct device and struct pci_dev pointers
which are basically duplicates of each other. Drop the latter
in favour of the former.
While here, unify pdev to be pointer to struct pci_device and reindent
some (touched) lines for better readability.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
There is no need to pass a pointer to struct device_driver
when we have an access to struct device already.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
There are specific ACPI and I\xB2C APIs to match device by different
parameters, such as ACPI HID, and retrieve an I\xB2C client.
Use them instead of home grown approach.
Note, it fixes a resource leak as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
IOSF MBI header contains a lot of definitions, such as
end point addresses of IPs. Move CCK address from AtomISP driver
to generic header.
While here, drop unused one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Intel MID special header is not in use in this driver.
Replace it with a better macro for now on.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Instead of parsing GPIO for two exceptions inside the logic
which would be trying to use the GPIO, move the init code
to the routine which adds a new gmin device.
Move the notes to it too, as this helps to identify where
those two GPIO settings are used, explaining why they're
defaulting to -1 when not found.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
There's only one place where a subdev can be added: when the
sensor driver registers it. Trying to do it elsewhere will
cause problems, as the detection code needs to access the
I2C bus in order to probe some things.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
If the ACPI DSDT tables provide _CRS for the camera, the
GPIO core code should be able to handle them automatically.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The media core has now a check if fi->pad is bigger than zero
or bigger than sd->entity.num_pads, if the media controller
is defined.
This causes a call to g_frame_interval to return -EINVAL.
Fix it by first cleaning up the struct.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Newer devices don't place the PMIC CLK line inside an EFI
var. Instead, those are found at the _PR0 table.
Add a parser for it, using info stored via the DSDT table.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add support code for this driver to use ACPI power management.
Yet, at least with known devices, this won't work without
further changes.
The rationale is that the ACPI handling code checks for the _PR? tables
in order to know what is required to switch the device from power state
D0 (_PR0) up to D3COLD (_PR3).
The adev->flags.power_manageable is set to true if the device has a _PR0
table, which can be checked by calling acpi_device_power_manageable(adev).
However, this only says that the device can be set to power off mode.
At least on the DSDT tables we've seen so far, there's no _PR3 nor _PS3
(which would have a somewhat similar effect).
So, using ACPI for power management won't work, except if adding
an ACPI override logic somewhere.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The gmin_subdev_add() currently doesn't use ACPI device
power management. In order to prepare for adding support
for it, let's shift some things, placing the PM-related
stuff at the end of the probing logic.
Let's also store the current gs on a temporary var, in
order to simplify the source code.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
In order to improve consistency and usability in cgroup stat accounting,
we would like to support the root cgroup's io.stat.
Since the root cgroup has processes doing io even if the system has no
explicitly created cgroups, we need to be careful to avoid overhead in
that case. For that reason, the rstat algorithms don't handle the root
cgroup, so just turning the file on wouldn't give correct statistics.
To get around this, we simulate flushing the iostat struct by filling it
out directly from global disk stats. The result is a root cgroup io.stat
file consistent with both /proc/diskstats and io.stat.
Note that in order to collect the disk stats, we needed to iterate over
devices. To facilitate that, we had to change the linkage of a disk_type
to external so that it can be used from blk-cgroup.c to iterate over
disks.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Boris Burkov <boris@bur.io>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Previously, the code which printed io.stat only needed access to the
generic rstat flushing code, but since we plan to write some more
specific code for preparing root cgroup stats, we need to manipulate
iostat structs directly. Since declaring static functions ahead does not
seem like common practice in this file, simply move the iostat functions
up. We only plan to use blkg_iostat_set, but it seems better to keep them
all together.
Signed-off-by: Boris Burkov <boris@bur.io>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Fix wrong reading of upper pages for SFP EEPROM. According to "Memory
Organization" figure in SFF-8472 spec: When reading upper pages 1, 2 and
3 the offset should be set relative to zero and I2C high address 0x51
[1010001X (A2h)] is to be used.
Fixes: a45bfb5a5070 ("mlxsw: core: Extend QSFP EEPROM size for ethtool")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Validate MAC address before copying the same to outgoing frame
skb destination address. Since a node can have zero mac
address for Link B until a valid frame is received over
that link, this fix address the issue of a zero MAC address
being in the packet.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For small Ethernet frames with size less than minimum size 66 for HSR
vs 60 for regular Ethernet frames, hsr driver currently doesn't pad the
frame to make it minimum size. This results in incorrect LSDU size being
populated in the HSR tag for these frames. Fix this by padding the frame
to the minimum size applicable for HSR.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The double poll additions were centered around doing POLL_ADD on file
descriptors that use more than one waitqueue (typically one for read,
one for write) when being polled. However, it can also end up being
triggered for when we use poll triggered retry. For that case, we cannot
safely use req->io, as that could be used by the request type itself.
Add a second io_poll_iocb pointer in the structure we allocate for poll
based retry, and ensure we use the right one from the two paths.
Fixes: 18bceab101ad ("io_uring: allow POLL_ADD with double poll_wait() users")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Drop the doubled word "be" in a comment.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is one RGMII check not using the phy_interface_mode_is_rgmii()
helper. This prevents the driver from configuring the MAC properly when
using a phy-mode that is not just rgmii, e.g. rgmii-rxid. This became an
issue on sama5d3 xplained since the ksz9031 driver is hadling phy-mode
properly and the phy-mode has to be set to rgmii-rxid.
Fixes: bcf3440c6dd78bfe ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch disables PTP on AQC111 and AQC112 due to a known HW issue,
which can cause datapath issues.
Ideally PTP block should have been disabled via PHY provisioning, but
unfortunately many units have been shipped with enabled PTP block.
Thus, we have to work around this in the driver.
Fixes: dbcd6806af420 ("net: aquantia: add support for Phy access")
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since 82af7aca ("Removal of FUTEX_FD"), some includes related to file
operations aren't needed anymore. More investigation around the includes
showed that a lot of includes aren't required for compilation, possible
due to redundant includes. Simplify the code by removing unused
includes.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20200702202843.520764-4-andrealmeid@collabora.com
|
|
Since fshared is only conveying true/false values, declare it as bool.
In get_futex_key() the usage of fshared can be restricted to the first part
of the function. If fshared is false the function is terminated early and
the subsequent code can use a constant 'true' instead of the variable.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20200702202843.520764-5-andrealmeid@collabora.com
|
|
into master
Pull NFS client fixes from Anna Schumaker:
"A few more NFS client bugfixes for Linux 5.8:
NFS:
- Fix interrupted slots by using the SEQUENCE operation
SUNRPC:
- revert d03727b248d0 to fix unkillable IOs
xprtrdma:
- Fix double-free in rpcrdma_ep_create()
- Fix recursion into rpcrdma_xprt_disconnect()
- Fix return code from rpcrdma_xprt_connect()
- Fix handling of connect errors
- Fix incorrect header size calculations"
* tag 'nfs-for-5.8-3' of git://git.linux-nfs.org/projects/anna/linux-nfs:
SUNRPC reverting d03727b248d0 ("NFSv4 fix CLOSE not waiting for direct IO compeletion")
xprtrdma: fix incorrect header size calculations
NFS: Fix interrupted slots by sending a solo SEQUENCE operation
xprtrdma: Fix handling of connect errors
xprtrdma: Fix return code from rpcrdma_xprt_connect()
xprtrdma: Fix recursion into rpcrdma_xprt_disconnect()
xprtrdma: Fix double-free in rpcrdma_ep_create()
|
|
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200713065859.31770-1-grandmaster@al2klimov.de
|
|
if of_find_device_by_node() succeed, at91_pm_sram_init() doesn't have
a corresponding put_device(). Thus add a jump target to fix the exception
handling for this function implementation.
Fixes: d2e467905596 ("ARM: at91: pm: use the mmio-sram pool to access SRAM")
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200604123301.3905837-1-yukuai3@huawei.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc into master
Pull ARM SoC fixes from Arnd Bergmann:
"This time there are a number of actual code fixes, plus a small set of
device tree issues getting addressed:
Renesas:
- one defconfig cleanup to allow a later Kconfig change
Intel socfpga:
- enable QSPI devices on some machines
- fix DTC validation warnings
TI OMAP:
- Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target
module driver
- A regression fix for ti-sysc no-idle handling that caused issues
compared to earlier platform data based booting
- A fix for memory leak for omap_hwmod_allocate_module
- Fix d_can driver probe for am437x
NXP i.MX:
- A couple of fixes on i.MX platform device registration code to
stop the use of invalid IRQ 0.
- Fix a regression seen on ls1021a platform, caused by commit
52102a3ba6a61 ("soc: imx: move cpu code to drivers/soc/imx").
- Fix a misconfiguration of audio SSI on imx6qdl-gw551x board.
Amlogic Meson:
- misc DT fixes
- SoC ID fixes to detect all chips correctly"
* tag 'arm-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: dts: spcfpga: Align GIC, NAND and UART nodenames with dtschema
ARM: dts: socfpga: Align L2 cache-controller nodename with dtschema
arm64: dts: stratix10: increase QSPI reg address in nand dts file
arm64: dts: stratix10: add status to qspi dts node
arm64: dts: agilex: add status to qspi dts node
ARM: dts: Fix dcan driver probe failed on am437x platform
ARM: OMAP2+: Fix possible memory leak in omap_hwmod_allocate_module
arm64: defconfig: Enable CONFIG_PCIE_RCAR_HOST
soc: imx: check ls1021a
ARM: imx: Remove imx_add_imx_dma() unused irq_err argument
ARM: imx: Provide correct number of resources when registering gpio devices
ARM: dts: imx6qdl-gw551x: fix audio SSI
bus: ti-sysc: Do not disable on suspend for no-idle
bus: ti-sysc: Fix sleeping function called from invalid context for RTC quirk
bus: ti-sysc: Fix wakeirq sleeping function called from invalid context
ARM: dts: meson: Align L2 cache-controller nodename with dtschema
arm64: dts: meson-gxl-s805x: reduce initial Mali450 core frequency
arm64: dts: meson: add missing gxl rng clock
soc: amlogic: meson-gx-socinfo: Fix S905X3 and S905D3 ID's
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux into master
Pull arm64 fixes from Will Deacon:
"A batch of arm64 fixes.
Although the diffstat is a bit larger than we'd usually have at this
stage, a decent amount of it is the addition of comments describing
our syscall tracing behaviour, and also a sweep across all the modular
arm64 PMU drivers to make them rebust against unloading and unbinding.
There are a couple of minor things kicking around at the moment (CPU
errata and module PLTs for very large modules), but I'm not expecting
any significant changes now for us in 5.8.
- Fix kernel text addresses for relocatable images booting using EFI
and with KASLR disabled so that they match the vmlinux ELF binary.
- Fix unloading and unbinding of PMU driver modules.
- Fix generic mmiowb() when writeX() is called from preemptible
context (reported by the riscv folks).
- Fix ptrace hardware single-step interactions with signal handlers,
system calls and reverse debugging.
- Fix reporting of 64-bit x0 register for 32-bit tasks via
'perf_regs'.
- Add comments describing syscall entry/exit tracing ABI"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
drivers/perf: Prevent forced unbinding of PMU drivers
asm-generic/mmiowb: Allow mmiowb_set_pending() when preemptible()
arm64: Use test_tsk_thread_flag() for checking TIF_SINGLESTEP
arm64: ptrace: Use NO_SYSCALL instead of -1 in syscall_trace_enter()
arm64: syscall: Expand the comment about ptrace and syscall(-1)
arm64: ptrace: Add a comment describing our syscall entry/exit trap ABI
arm64: compat: Ensure upper 32 bits of x0 are zero on syscall return
arm64: ptrace: Override SPSR.SS when single-stepping is enabled
arm64: ptrace: Consistently use pseudo-singlestep exceptions
drivers/perf: Fix kernel panic when rmmod PMU modules during perf sampling
efi/libstub/arm64: Retain 2MB kernel Image alignment if !KASLR
|
|
As stated in the coding style documentation, "if there is no cleanup
needed then just return directly", instead of jumping to a label and
then returning.
Remove such goto's and replace with a return statement. When there's a
ternary operator on the return value, replace it with the result of the
operation when it is logically possible to determine it by the control
flow.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20200702202843.520764-3-andrealmeid@collabora.com
|
|
Since 4b39f99c ("futex: Remove {get,drop}_futex_key_refs()"),
put_futex_key() is empty.
Remove all references for this function and the then redundant labels.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20200702202843.520764-2-andrealmeid@collabora.com
|
|
This patch adds IMX274 optional external clock input and voltage
supplies to device tree bindings.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
|
|
Setting interrupt affinity on inactive interrupts is inconsistent when
hierarchical irq domains are enabled. The core code should just store the
affinity and not call into the irq chip driver for inactive interrupts
because the chip drivers may not be in a state to handle such requests.
X86 has a hacky workaround for that but all other irq chips have not which
causes problems e.g. on GIC V3 ITS.
Instead of adding more ugly hacks all over the place, solve the problem in
the core code. If the affinity is set on an inactive interrupt then:
- Store it in the irq descriptors affinity mask
- Update the effective affinity to reflect that so user space has
a consistent view
- Don't call into the irq chip driver
This is the core equivalent of the X86 workaround and works correctly
because the affinity setting is established in the irq chip when the
interrupt is activated later on.
Note, that this is only effective when hierarchical irq domains are enabled
by the architecture. Doing it unconditionally would break legacy irq chip
implementations.
For hierarchial irq domains this works correctly as none of the drivers can
have a dependency on affinity setting in inactive state by design.
Remove the X86 workaround as it is not longer required.
Fixes: 02edee152d6e ("x86/apic/vector: Ignore set_affinity call for inactive interrupts")
Reported-by: Ali Saidi <alisaidi@amazon.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Ali Saidi <alisaidi@amazon.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200529015501.15771-1-alisaidi@amazon.com
Link: https://lkml.kernel.org/r/877dv2rv25.fsf@nanos.tec.linutronix.de
|
|
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
[ tglx: Distangled it from the mess in -next ]
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: hch@lst.de
Link: https://lkml.kernel.org/r/20200716084747.8034-1-miaoqinglang@huawei.com
|
|
Add the OPP tables for DSI and MDP based on the perf state/clk
requirements, and add the power-domains property to specify the
scalable power domain.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1594292674-15632-5-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add the OPP tables for DSI and MDP based on the perf state/clk
requirements, and add the power-domains property to specify the
scalable power domain.
Tested-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1594292674-15632-4-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Commit 01397e822af4 ("kunit: Fix TabError, remove defconfig code and
handle when there is no kunitconfig") and commit 45ba7a893ad8 ("kunit:
kunit_tool: Separate out config/build/exec/parse") introduced two
closely related issues which built off of each other: they excessively
created the build directory when not present and modified a constant
(constants in Python only exist by convention).
Together these issues broken a number of unit tests for KUnit tool, so
fix them.
Fixed up commit log to fic checkpatch commit description style error.
Shuah Khan <skhan@linuxfoundation.org>
Fixes: 01397e822af4 ("kunit: Fix TabError, remove defconfig code and handle when there is no kunitconfig")
Fixes: 45ba7a893ad8 ("kunit: kunit_tool: Separate out config/build/exec/parse")
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
Commit ddbd60c779b4 ("kunit: use --build_dir=.kunit as default") changed
the default build directory for KUnit tests, but failed to update
associated unit tests for kunit_tool, so update them.
Fixes: ddbd60c779b4 ("kunit: use --build_dir=.kunit as default")
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
Direct stderr to subprocess.STDOUT so error messages get included in the
subprocess.CalledProcessError exceptions output field. This results in
more meaningful error messages for the user.
This is already being done in the make_allyesconfig method. Do the same
for make_mrproper, make_olddefconfig, and make methods.
With this, failures on unclean trees [1] will give users an error
message that includes:
"The source tree is not clean, please run 'make ARCH=um mrproper'"
[1] https://bugzilla.kernel.org/show_bug.cgi?id=205219
Signed-off-by: Will Chen <chenwi@google.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
The --defconfig option in kunit_tool was removed in [1], but the getting
started and kunit_tool documentation still encouraged its use. Update
those documents to reflect that it's no-longer required, and is the
default behaviour if no .kunitconfig is found.
Also update a couple of places where .kunitconfig is still referred to
as kunitconfig (this was changed in [2]).
[1]:
https://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest.git/commit/?h=kunit-fixes&id=9bdf64b35117cc10813d24e1842cd8ee40ecbf19
[2]:
https://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest.git/commit/?h=kunit-fixes&id=14ee5cfd4512ee3d1e0047d8751450dcc6544070
Signed-off-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
When nfc_register_device fails in nci_register_device,
destroy_workqueue() shouled be called to destroy ndev->tx_wq.
Fixes: 3c1c0f5dc80b ("NFC: NCI: Fix nci_register_device init sequence")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Doug Berger says:
====================
net: bcmgenet: fix WAKE_FILTER resume from deep sleep
The WAKE_FILTER logic can only wake the system from the standby
power state. However, some systems that include the GENET IP
support deeper power saving states and the driver should suspend
and resume correctly from those states as well.
This commit set squashes a few issues uncovered while testing
suspend and resume from these deep sleep states.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Hardware Filter Block RAM may not be preserved when the GENET
block is reset during a deep sleep, so it is not sufficient to
only backup and restore the enables.
This commit clears out the HFB block and reprograms the rxnfc
rules when the system resumes from a suspended state. To support
this the bcmgenet_hfb_create_rxnfc_filter() function is modified
to access the register space directly so that it can't fail due
to memory allocation issues.
Fixes: f50932cca632 ("net: bcmgenet: add WAKE_FILTER support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the GENET driver resumes from deep sleep the UMAC_CMD
register may not be accessible and therefore should not be
accessed from bcmgenet_wol_power_up_cfg() if the GENET has
been reset.
This commit adds a check of the RBUF_ACPI_EN flag when Wake
on Filter is enabled. A clear flag indicates that the GENET
hardware must have been reset so the remainder of the
hardware programming is bypassed.
Fixes: f50932cca632 ("net: bcmgenet: add WAKE_FILTER support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the GENET driver resumes from deep sleep the UMAC_CMD
register may not be accessible and therefore should not be
accessed from bcmgenet_wol_power_up_cfg() if the GENET has
been reset.
This commit adds a check of the MPD_EN flag when Wake on
Magic Packet is enabled. A clear flag indicates that the
GENET hardware must have been reset so the remainder of the
hardware programming is bypassed.
Fixes: 1a1d5106c1e3 ("net: bcmgenet: move clk_wol management to bcmgenet_wol")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the selftest "step" counter grew beyond 255, non-fatal warnings
were being emitted, which is noisy and pointless. There are selftests
with more than 255 steps (especially those in loops, etc). Instead,
just cap "steps" to 254 and do not report the saturation.
Reported-by: Ralph Campbell <rcampbell@nvidia.com>
Tested-by: Ralph Campbell <rcampbell@nvidia.com>
Fixes: 9847d24af95c ("selftests/harness: Refactor XFAIL into SKIP")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
There is nothing that prevents from forwarding the base clock if it's one
jiffy off. The reason for this arbitrary limit of two jiffies is historical
and does not longer exist.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juri Lelli <juri.lelli@redhat.com>
Link: https://lkml.kernel.org/r/20200717140551.29076-13-frederic@kernel.org
|
|
There is no reason to keep this guard around. The code makes sure that
base->clk remains sane and won't be forwarded beyond jiffies nor set
backward.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juri Lelli <juri.lelli@redhat.com>
Link: https://lkml.kernel.org/r/20200717140551.29076-12-frederic@kernel.org
|
|
Now that the core timer infrastructure doesn't depend anymore on
periodic base->clk increments, even when the CPU is not in NO_HZ mode,
timer softirqs can be skipped until there are timers to expire.
Some spurious softirqs can still remain since base->next_expiry doesn't
keep track of canceled timers but this still reduces the number of softirqs
significantly: ~15 times less for HZ=1000 and ~5 times less for HZ=100.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juri Lelli <juri.lelli@redhat.com>
Link: https://lkml.kernel.org/r/20200717140551.29076-11-frederic@kernel.org
|
|
As for next_expiry, the base->clk catch up logic will be expanded beyond
NOHZ in order to avoid triggering useless softirqs.
If softirqs should only fire to expire pending timers, periodic base->clk
increments must be skippable for random amounts of time. Therefore prepare
to catch-up with missing updates whenever an up-to-date base clock is
needed.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juri Lelli <juri.lelli@redhat.com>
Link: https://lkml.kernel.org/r/20200717140551.29076-10-frederic@kernel.org
|
|
Now that the next expiry it tracked unconditionally when a timer is added,
this information can be reused on a tick firing after exiting nohz.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juri Lelli <juri.lelli@redhat.com>
Link: https://lkml.kernel.org/r/20200717140551.29076-9-frederic@kernel.org
|
