| Age | Commit message (Collapse) | Author |
|---|
|
In order to save power the DDR pins should be put into high
impedance when in suspend to RAM.
This requires manually requesting self refresh (rather than using the
automatic mode implemented by the CCM / ESDCTL), followed by
reconfiguring the IOMUXC.
Of course the code to do this cannot itself run from DDR so the
code is copied to and executed from internal memory.
In my tests using a custom i.MX53 board with LPDDR2 RAM
this reduced the suspend power consumption from 200mW to 60mW.
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add i.MX7D MSL support.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add low level uart debug support for imx7d
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Bai Ping <b51503@freescale.com>
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Include the "common.h" header file to fix the following sparse warning:
arch/arm/mach-imx/mmdc.c:66:5: warning: symbol 'imx_mmdc_get_ddr_type' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Include the "clk.h" header file to fix the following sparse warning:
drivers/clk/imx/clk-cpu.c:77:12: warning: symbol 'imx_clk_cpu' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The comments were corrected as the following to reflect
the real situation of Freescale MXC timer IP block.
There are totally 4 version of the timer on Freescale i.MX SoCs.
Signed-off-by: Shenwei Wang <shenwei.wang@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Removed the duplicated function declaration of mxc_timer_init
which was already declared in drivers/clk/imx/clk.h.
Signed-off-by: Shenwei Wang <shenwei.wang@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The definition of do_div uses unsigned long long
variable as its first parameter, better to pass
a u64 variable as first parameter when calling
do_div function.
Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Commit 4631960d26da ("ARM: imx6: set initial power mode in pm function")
moves imx6_set_lpm() from clock init function into
imx6_pm_common_init(). This causes a hang when cpuidle support is
enabled. The reason for that is ARM core clock is shut down
unexpectedly by WAIT mode. It happens with the following call stack:
cpuidle_register_governor()
cpuidle_switch_governor()
cpuidle_uninstall_idle_handler()
synchronize_sched()
wait_rcu_gp()
wait_for_completion()
When wait_for_completion() is called as above, all cores are idle/WFI.
Hence, the reset value of CCM_CLPCR_LPM - WAIT mode, will trigger a
hardware shutdown of the ARM core clock.
To fix the regression, we need to ensure that CCM_CLPCR_LPM is
initialized into RUN mode earlier than cpuidle governor registration,
which is a postcore_initcall. This patch creates function
imx6_pm_ccm_init() to map CCM block and initialize CCM_CLPCR_LPM into
RUN mode, and have the function called from machine .init_irq hook,
which should be early enough.
Reported-by: Kevin Hilman <khilman@kernel.org>
Fixes: 8fb76a07e2cb ("ARM: imx6: set initial power mode in pm function")
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
EPIT provides another timer implementation besides the default GPT
timer. The imx35 clock driver will use EPIT timer when option
CONFIG_MXC_USE_EPIT is enabled. However, initializing timers from
clock driver is a workaround solution and causes problem when we move
clock drivers into driver/clk.
Let's simply drop the EPIT initialization from there. If people really
want this EPIT option, EPIT timer driver needs to be reworked to do the
initialization in a standard way - use CLOCKSOURCE_OF_DECLARE() with
device tree support.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add new created folders drivers/clk/imx/ and include/soc/imx/ into IMX
entry.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
After the cleanup on clock drivers, they are now ready to be moved into
drivers/clk. Let's move them into drivers/clk/imx folder.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
With the cleanup done before, we now can simply define base address and
irq as needed in clock driver, to get those platform header inclusions
removed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Instead of calling cpu_is_xxx() in clk-pllv1 driver, let's add clk-pllv1
type support to handle the difference/quirk in particular SoC designs.
Doing so will help get clk-pllv1 driver ready for being moved out of
arch/arm/mach-imx folder.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
As we're about to move clock drivers out of arch/arm/mach-imx,
cpu_is_xxx() shouldn't be used any more. Let's avoid the call by
looking at the device tree machine compatible string to determine
which SoC the clock driver is running on.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
We are about to move imx6 clock driver into drivers/clk, so let's get
imx6 pm code map CCM block on its own rather than relying on clock
driver to do the mapping.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Rather than setting initial low-power mode in every single i.MX6 clock
initialization function, we should really do that in pm code. Let's
move imx6q_set_lpm(WAIT_CLOCKED) call into imx6_pm_common_init().
While at it, let's rename the function to imx6_set_lpm() since it's
actually common for all i.MX6 SoCs.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
We are about to move imx5 clock driver into drivers/clk, so let's get
imx5 pm code map CCM block on its own rather than relying on clock
driver to do the mapping.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The revision definitions and declarations are widely used by clock
drivers. As a step of moving clock drivers out of arch/arm/mach-imx,
let's create header include/soc/imx/revision.h to accommodate them.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Replace the static mapping of CCM block in clock drivers with dynamic
mapping.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Pass physical address of timer block to mxc_timer_init() call, which in
turn does dynamic mapping within the function. Thus, we can avoid using
static mapping in clock drivers.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
It adds the imx7d clock ID definitions which will be used by both imx7d
clock driver and device tree.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The Odroid XU3 Lite is almost the same as XU3, except:
1. Lower CPU frequencies (1.8 GHz for A15 and 1.3 GHz for A7, instead of
2.0 GHz and 1.4 GHz).
2. No DisplayPort.
3. No TI INA231 energy measurement sensors.
This patch moves common nodes (which is almost everything) to a common
DTSI file and adds a new XU3 Lite DTS.
Currently in comparison to XU3, only the INA231 sensors are disabled to
remove the warning:
ina2xx 0-0040: error configuring the device: -6
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Add Hardkernel Co., Ltd. to the list of device tree vendor prefixes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
The IRQB of S2MPS11 PMIC is wired to XEINT4 (GPX0-4) through pull-up
resistor.
Add interrupt properties and pinctrl configuration to enable RTC wake
alarm of rtc-s5m driver. This also removes a warning:
sec_pmic 4-0066: No interrupt specified, no interrupts
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Add nodes for jpeg codec in Exynos5420 SoC.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
[k.kozlowski: fixed up minor differences for applying]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Add new labels to certain nodes on S3C2416 so they could be easily
referenced by board DTS files.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes. Additionally remove duplicated serial and uart labels
for serial.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
The i2c_7 node (i2c@12CD0000) with LVDS bridge child node was put in
Exynos5250 Snow DTS file twice. Move the LVDS bridge to proper existing
i2c_7 node.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Add new labels to certain nodes so they could be easily referenced by
Exynos5 board DTS files.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
PWM output wasn't working because it wasn't hooked up to its pincontrol.
This patch:
- hooks up PWM to its pincontrol, and documents what
the outputs are on the XU3
- switches the LEDs that are on PWM outputs to use PWM
rather than GPIO.
The main effect is that the brightness of the LEDs can be controlled, and
user-mode fan control is enabled via /sys/class/pwm
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Peter Chubb <peter.chubb@nicta.com.au>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
For thermal zones:
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
