summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2021-04-07irqchip/irq-mst: Support polarity configurationMark-PK Tsai
Support irq polarity configuration and save and restore the config when system suspend and resume. Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com> [maz: fixed irq_set_type callback] Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20210315131848.31840-1-mark-pk.tsai@mediatek.com
2021-04-07irqchip: Add driver for WPCM450 interrupt controllerJonathan Neuschäfer
The WPCM450 AIC ("Advanced Interrupt Controller") is the interrupt controller found in the Nuvoton WPCM450 SoC and other Winbond/Nuvoton SoCs. The list of registers if based on the AMI vendor kernel and the Nuvoton W90N745 datasheet. Although the hardware supports other interrupt modes, the driver only supports high-level interrupts at the moment, because other modes could not be tested so far. Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20210406120921.2484986-7-j.neuschaefer@gmx.net
2021-04-07dt-bindings: interrupt-controller: Add nuvoton, wpcm450-aicJonathan Neuschäfer
The WPCM450 AIC ("Advanced Interrupt Controller") is the interrupt controller found in the Nuvoton WPCM450 SoC and other Winbond/Nuvoton SoCs. Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20210406120921.2484986-4-j.neuschaefer@gmx.net
2021-04-07dt-bindings: qcom,pdc: Add compatible for sc7280Rajendra Nayak
Add the compatible string for sc7280 SoC from Qualcomm Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/1615787946-26474-1-git-send-email-rnayak@codeaurora.org
2021-04-07irqchip/stm32: Add usart instances exti direct event supportErwan Le Ray
Add following usart instances exti direct event support (used for UART wake up). - exti 26 (USART1) is mapped to GIC 37 - exti 27 (USART2) is mapped to GIC 38 - exti 28 (USART3) is mapped to GIC 39 - exti 29 (USART6) is mapped to GIC 71 - exti 31 (UART5) is mapped to GIC 53 - exti 32 (UART7) is mapped to GIC 82 - exti 33 (UART8) is mapped to GIC 83 Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20210319184253.5841-4-erwan.leray@foss.st.com
2021-04-07irqchip/gic-v3: Fix OF_BAD_ADDR error handlingArnd Bergmann
When building with extra warnings enabled, clang points out a mistake in the error handling: drivers/irqchip/irq-gic-v3-mbi.c:306:21: error: result of comparison of constant 18446744073709551615 with expression of type 'phys_addr_t' (aka 'unsigned int') is always false [-Werror,-Wtautological-constant-out-of-range-compare] if (mbi_phys_base == OF_BAD_ADDR) { Truncate the constant to the same type as the variable it gets compared to, to shut make the check work and void the warning. Fixes: 505287525c24 ("irqchip/gic-v3: Add support for Message Based Interrupts as an MSI controller") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20210323131842.2773094-1-arnd@kernel.org
2021-04-07irqchip/sifive-plic: Mark two global variables __ro_after_initJisheng Zhang
All of these two are never modified after init, so they can be __ro_after_init. Signed-off-by: Jisheng Zhang <jszhang@kernel.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20210330020911.26423e9e@xhacker
2021-04-07irqchip/hisi: Use the correct HiSilicon copyrightHao Fang
s/Hisilicon/HiSilicon/ It should use capital S, according to https://www.hisilicon.com/en/terms-of-use. Signed-off-by: Hao Fang <fanghao11@huawei.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/1617086780-8521-1-git-send-email-fanghao11@huawei.com
2021-04-07mips: netlogic: Use irq_domain_simple_ops for XLP PICMarc Zyngier
Use the generic irq_domain_simple_ops structure instead of a home-grown one. Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Marc Zyngier <maz@kernel.org>
2021-04-07irqdomain: Get rid of irq_create_identity_mapping()Marc Zyngier
The sole user of irq_create_identity_mapping() having been converted, get rid of the unused helper. Signed-off-by: Marc Zyngier <maz@kernel.org>
2021-04-07ARM: dts: clps711x: Add an empty chosen node to top level DTSIAlexander Shiyan
Missing "chosen" node can cause issues when booting a kernel with a boot-loader that doesn't create a chosen node if this isn't present in the DTB since the decompressor relies on a pre-existing chosen node to be available to insert the command line and merge other ATAGS info. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Link: https://lore.kernel.org/r/20210405051658.26779-5-shc_work@mail.ru' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-04-07ARM: dts: clps711x: edb7211: Add unit-address to memory nodeAlexander Shiyan
The memory node requires a unit-address, add it. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Link: https://lore.kernel.org/r/20210405051658.26779-4-shc_work@mail.ru' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-04-07ARM: dts: clps711x: Fix serial port namesAlexander Shiyan
Preferred node name for serial ports is "serial". Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Link: https://lore.kernel.org/r/20210405051658.26779-3-shc_work@mail.ru' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-04-07ARM: dts: clps711x: Add keypad nodeAlexander Shiyan
This adds missing keypad node to basic clps711x DT. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Link: https://lore.kernel.org/r/20210405051658.26779-2-shc_work@mail.ru' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-04-07ARM: dts: clps711x: Add SYSCON nodes where it is usedAlexander Shiyan
This patch adds SYSCON descriptors to framebuffer, SPI, DAI and modem control GPIO nodes to further rework these drivers to remove the call to the syscon_regmap_lookup_by_compatible() function. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Link: https://lore.kernel.org/r/20210405051658.26779-1-shc_work@mail.ru' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-04-07Merge tag 'qcom-arm64-for-5.13' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt Qualcomm ARM64 DT updates for 5.13 This extends the initial SM8350 description merged in v5.12 with CPUfreq, SMMU, UFS, RPMHPD, SPMI, USB and remoteproc support. It adds initial PMIC definitions for the 6 PMICs found on the MTP and it introduces the new SM8350 Hardware Development Kit (HDK). SC7180 is further polished, the DisplayPort portion of the QMP phy is defined and several new SKUs of the Trogdor devices are introduced. The new SC7280 platform is introduced, with RPMH, RPMHPD, RPMCC, SPMI, CPU idle, SMMU and watchdog defined. SDM845 gains the camera related nodes and some cleanups. For SM8250 it brings some cleanups and migrates SPI0 to use GPIO for chip select. * tag 'qcom-arm64-for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (79 commits) arm64: dts: qcom: qrb5165-rb5: switch into using GPIO for SPI0 CS arm64: dts: qcom: sm8250: add pinctrl for SPI using GPIO as a CS arm64: dts: qcom: sm8250: further split of spi pinctrl config arm64: dts: qcom: sm8250: split spi pinctrl config arm64: dts: qcom: sdm845-db845c: Enable ov8856 sensor and connect to ISP arm64: dts: qcom: sdm845-db845c: Configure regulators for camss node arm64: dts: qcom: sdm845: Add CAMSS ISP node arm64: dts: qcom: pm8150: Enable RTC arm64: dts: qcom: sm8350-mtp: Add PMICs arm64: dts: qcom: pmr735B: Add base dts file arm64: dts: qcom: pmr735a: Add base dts file arm64: dts: qcom: pm8350c: Add base dts file arm64: dts: qcom: pm8350b: Add base dts file arm64: dts: qcom: pm8350: Add base dts file arm64: dts: qcom: pmk8350: Add base dts file arm64: dts: qcom: sm8350: Add spmi node arm64: dts: qcom: db845c: fix correct powerdown pin for WSA881x dt-bindings: arm: qcom: Add SM8350 HDK arm64: dts: qcom: sc7180: Drop duplicate dp_hot_plug_det node in trogdor arm64: dts: qcom: sm8350: fix number of pins in 'gpio-ranges' ... Link: https://lore.kernel.org/r/20210404164914.712946-1-bjorn.andersson@linaro.org Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-04-07Merge tag 'mvebu-dt64-5.13-1' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/dt mvebu dt64 for 5.13 (part 1) Add DT for fan control on SolidRun Clearfog GT8k platform Add syscon compatible to NB clk node allowing improving cpufreq support on Armada 37xx Add support for UTMI PHY allowing removing kernel dependency from the boot loader for UBS port connected to this PHY (Armada 7K, 8K and CN91xx) * tag 'mvebu-dt64-5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu: arm64: dts: marvell: enable CP110 UTMI PHY usage arm64: dts: marvell: add support for Marvell CP110 UTMI PHY arm64: dts: marvell: armada-37xx: add syscon compatible to NB clk node arm64: dts: marvell: clearfog-gt-8k: add cooling maps arm64: dts: marvell: clearfog-gt-8k: add pwm-fan Link: https://lore.kernel.org/r/874kgocs7t.fsf@BL-laptop Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-04-07Merge tag 'sunxi-dt-for-5.13-1' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt Our usual bunch of patches to support the Allwinner SoCs, this time adding: - New secondary interrupt controller binding to support the wake-up - Use the RSB bus instead of I2C for the PMIC on the H6 - HDMI support for the BananaPi M2-Zero - New board: Topwise A721 * tag 'sunxi-dt-for-5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: ARM: dts: sun8i: h3: beelink-x2: Add power button arm64: dts: allwinner: h6: Use RSB for AXP805 PMIC connection ARM: dts: sunxi: h2-plus-bananapi-m2-zero: Add HDMI out ARM: dts: sun4i: Add support for Topwise A721 tablet dt-bindings: arm: Add Topwise A721 arm64: dts: allwinner: Move wakeup-capable IRQs to r_intc arm64: dts: allwinner: Use the new r_intc binding ARM: dts: sunxi: Move wakeup-capable IRQs to r_intc ARM: dts: sunxi: h3/h5: Add r_intc node ARM: dts: sunxi: Use the new r_intc binding Link: https://lore.kernel.org/r/8a3e3271-bebe-4d27-a9e7-7b7a6311a38d.lettre@localhost Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-04-07Merge tag 'renesas-arm-dt-for-v5.13-tag2' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt Renesas ARM DT updates for v5.13 (take two) - Video IN (VIN) and Camera (CSI-2) support for the R-Car M3-W+ SoC, - LED support for the Falcon development board, - Preparatory display pipeline support for the R-Car V3U SoC, - Miscellaneous fixes and improvements. * tag 'renesas-arm-dt-for-v5.13-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: arm64: dts: renesas: ulcb: Add cpu-supply property to a57_0 node arm64: dts: renesas: salvator-common: Add cpu-supply property to a57_0 node arm64: dts: renesas: r8a77950: Drop operating points above 1.5 GHz arm64: dts: renesas: r8a779a0: Fix PMU interrupt arm64: dts: renesas: r8a779a0: Add VSPD support arm64: dts: renesas: r8a779a0: Add FCPVD support arm64: dts: renesas: falcon-cpu: Add GP LEDs arm64: dts: renesas: r8a77961: Add VIN and CSI-2 device nodes ARM: dts: koelsch: Configure pull-up for SOFT_SW GPIO keys arm64: dts: renesas: falcon: Move AVB0 to main DTS arm64: dts: renesas: falcon: Move watchdog config to CPU board DTS arm64: dts: renesas: falcon: Move console config to CPU board DTS Link: https://lore.kernel.org/r/cover.1617359678.git.geert+renesas@glider.be Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-04-07arm64: dts: allwinner: h6: beelink-gs1: Remove ext. 32 kHz osc referenceJernej Skrabec
Although every Beelink GS1 seems to have external 32768 Hz oscillator, it works only on one from four tested. There are more reports of RTC issues elsewhere, like Armbian forum. One Beelink GS1 owner read RTC osc status register on Android which shipped with the box. Reported value indicated problems with external oscillator. In order to fix RTC and related issues (HDMI-CEC and suspend/resume with Crust) on all boards, switch to internal oscillator. Fixes: 32507b868119 ("arm64: dts: allwinner: h6: Move ext. oscillator to board DTs") Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Tested-by: Clément Péron <peron.clem@gmail.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20210330184218.279738-1-jernej.skrabec@siol.net
2021-04-07MAINTAINERS: Match on allwinner keywordMaxime Ripard
Some drivers (phy, crypto, net) folders don't have sunxi in it but allwinner. Add that keyword to match on it too. Signed-off-by: Maxime Ripard <maxime@cerno.tech> Acked-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Jernej Skrabec <jernej.skrabec@siol.net> Link: https://lore.kernel.org/r/20210331130830.64182-2-maxime@cerno.tech
2021-04-07MAINTAINERS: Add our new mailing-listMaxime Ripard
We've been struggling to get an LF-hosted mailing list for a while, but now that lists.linux.dev is there we opted in. Let's add it to MAINTAINERS. Signed-off-by: Maxime Ripard <maxime@cerno.tech> Acked-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Jernej Skrabec <jernej.skrabec@siol.net> Link: https://lore.kernel.org/r/20210331130830.64182-1-maxime@cerno.tech
2021-04-07arm64: dts: allwinner: Fix SD card CD GPIO for SOPine systemsAndre Przywara
Commit 941432d00768 ("arm64: dts: allwinner: Drop non-removable from SoPine/LTS SD card") enabled the card detect GPIO for the SOPine module, along the way with the Pine64-LTS, which share the same base .dtsi. However while both boards indeed have a working CD GPIO on PF6, the polarity is different: the SOPine modules uses a "push-pull" socket, which has an active-high switch, while the Pine64-LTS use the more traditional push-push socket and the common active-low switch. Fix the polarity in the sopine.dtsi, and overwrite it in the LTS board .dts, to make the SD card work again on systems using SOPine modules. Fixes: 941432d00768 ("arm64: dts: allwinner: Drop non-removable from SoPine/LTS SD card") Reported-by: Ashley <contact@victorianfox.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20210316144219.5973-1-andre.przywara@arm.com
2021-04-07arm64: dts: allwinner: h6: Switch to macros for RSB clock/reset indicesChen-Yu Tsai
The macros for the clock and reset indices for the RSB hardware block were replaced with raw numbers when the RSB controller node was added. This was done to avoid cross-tree dependencies. Now that both the clk and DT changes have been merged, we can switch back to using the macros. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime@cerno.tech>
2021-04-07ARM: dts: at91: sama5d2: add ETB and ETM unit nameNicolas Ferre
Add unit address to the ETB and ETM nodes. It also allow us to get rid of the warnings: ../arch/arm/boot/dts/sama5d2.dtsi:43.6-57.4: Warning (unit_address_vs_reg): /etb: node has a reg or ranges property, but no unit name ../arch/arm/boot/dts/sama5d2.dtsi:59.6-73.4: Warning (unit_address_vs_reg): /etm: node has a reg or ranges property, but no unit name when we compile with W=1. Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20210402170139.140595-1-nicolas.ferre@microchip.com
2021-04-07ARM: dts: at91: change the key code of the gpio keyLudovic Desroches
Having a button code and not a key code causes issues with libinput. udev won't set ID_INPUT_KEY. If it is forced, then it causes a bug within libinput. Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20210402130227.21478-1-nicolas.ferre@microchip.com
2021-04-07printk: clarify the documentation for plain pointer printingVlastimil Babka
We have several modifiers for plain pointers (%p, %px and %pK) and now also the no_hash_pointers boot parameter. The documentation should help to choose which variant to use. Importantly, we should discourage %px in favor of %p (with the new boot parameter when debugging), and stress that %pK should be only used for procfs and similar files, not dmesg buffer. This patch clarifies the documentation in that regard. Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org> Reviewed-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Petr Mladek <pmladek@suse.com> Link: https://lore.kernel.org/r/20210225164639.27212-1-vbabka@suse.cz
2021-04-07sh: intc: Drop the use of irq_create_identity_mapping()Marc Zyngier
Instead of playing games with using irq_create_identity_mapping() and irq_domain_associate(), drop the use of the former and only use the latter, together with the allocation of the irq_desc as needed. It doesn't make the code less awful, but at least the intent is clearer. Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Marc Zyngier <maz@kernel.org>
2021-04-07RAS/CEC: Correct ce_add_elem()'s returned valuesWilliam Roche
ce_add_elem() uses different return values to signal a result from adding an element to the collector. Commit in Fixes: broke the case where the element being added is not found in the array. Correct that. [ bp: Rewrite commit message, add kernel-doc comments. ] Fixes: de0e0624d86f ("RAS/CEC: Check count_threshold unconditionally") Signed-off-by: William Roche <william.roche@oracle.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/1617722939-29670-1-git-send-email-william.roche@oracle.com
2021-04-07Revert "driver core: platform: Make platform_get_irq_optional() optional"Greg Kroah-Hartman
This reverts commit ed7027fdf4ec41ed6df6814956dc11860232a9d5 as it causes runtime issues: https://lore.kernel.org/r/20210406192514.GA34677@roeck-us.net Link: https://lore.kernel.org/r/20210406192514.GA34677@roeck-us.net Reported-by: Guenter Roeck <linux@roeck-us.net> Cc: Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-07bus: mhi: pci_generic: Add FIREHOSE channelsLoic Poulain
When device enters flash programmer context (FP), it exposes firehose protocol through the EDL dedicated channels. Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/1617784860-32439-1-git-send-email-loic.poulain@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2021-04-07staging: rtl8188eu: remove an obsolete commentMartin Kaiser
This driver does not set URB_ZERO_PACKET. The rtl8188eu driver that's available from Realtek/Edimax has some commented-out code that sets zero packet. It was removed from this driver before it was imported. Signed-off-by: Martin Kaiser <martin@kaiser.cx> Link: https://lore.kernel.org/r/20210406204829.18130-11-martin@kaiser.cx Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-07staging: rtl8188eu: clean up usb_write32Martin Kaiser
Remove unnecessary variable, summarize declaration and assignment. Signed-off-by: Martin Kaiser <martin@kaiser.cx> Link: https://lore.kernel.org/r/20210406204829.18130-10-martin@kaiser.cx Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-07staging: rtl8188eu: clean up usb_write16Martin Kaiser
Remove unnecessary variable, summarize declaration and assignment. Signed-off-by: Martin Kaiser <martin@kaiser.cx> Link: https://lore.kernel.org/r/20210406204829.18130-9-martin@kaiser.cx Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-07staging: rtl8188eu: clean up usb_write8Martin Kaiser
Remove unnecessary variable, summarize declaration and assignment. Signed-off-by: Martin Kaiser <martin@kaiser.cx> Link: https://lore.kernel.org/r/20210406204829.18130-8-martin@kaiser.cx Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-07staging: rtl8188eu: clean up usb_read32Martin Kaiser
Remove unnecessary variable, summarize declaration and assignment. Signed-off-by: Martin Kaiser <martin@kaiser.cx> Link: https://lore.kernel.org/r/20210406204829.18130-7-martin@kaiser.cx Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-07staging: rtl8188eu: clean up usb_read16Martin Kaiser
Remove unnecessary variable, summarize declaration and assignment. Signed-off-by: Martin Kaiser <martin@kaiser.cx> Link: https://lore.kernel.org/r/20210406204829.18130-6-martin@kaiser.cx Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-07staging: rtl8188eu: clean up usb_read8Martin Kaiser
Remove unnecessary variable, summarize declaration and assignment. Signed-off-by: Martin Kaiser <martin@kaiser.cx> Link: https://lore.kernel.org/r/20210406204829.18130-5-martin@kaiser.cx Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-07staging: rtl8188eu: use actual request type as parameterMartin Kaiser
At the moment, usbctrl_vendorreq's requesttype parameter must be set to 1 for reading and 0 for writing. It's then converted to the actual bmRequestType for the USB control request. We can simplify the code and avoid this conversion if the caller passes the actual bmRequestType. We already have defines for the read and write request types. Move them to usb_ops_linux.c, they're used only inside this file. Replace the numeric values with USB constants to make their meaning clearer. Signed-off-by: Martin Kaiser <martin@kaiser.cx> Link: https://lore.kernel.org/r/20210406204829.18130-4-martin@kaiser.cx Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-07staging: rtl8188eu: ctrl vendor req index is not usedMartin Kaiser
The index for rtl8188eu's vendor-specific control requests is not used. Remove the index parameter from usbctrl_vendorreq and pass index 0 to usb_control_msg. Signed-off-by: Martin Kaiser <martin@kaiser.cx> Link: https://lore.kernel.org/r/20210406204829.18130-3-martin@kaiser.cx Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-07staging: rtl8188eu: ctrl vendor req value is always 0x05Martin Kaiser
The bRequest value for the vendor specific control requests sent by this driver is always 0x05. Replace the function parameter with a define. Use the same define as the rtlwifi driver. Signed-off-by: Martin Kaiser <martin@kaiser.cx> Link: https://lore.kernel.org/r/20210406204829.18130-2-martin@kaiser.cx Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-07staging: rtl8188eu: remove unused efuse hal componentsMartin Kaiser
struct hal_data_8188e contains some components related to efuses which are not used for rtl8188eu. Signed-off-by: Martin Kaiser <martin@kaiser.cx> Link: https://lore.kernel.org/r/20210406204829.18130-1-martin@kaiser.cx Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-07staging: rt8192u: change constants to be on rightVardhan H G
When comparing a constant with variable, it is recommeneded to have the constant on the right side of the test. This patch silences the following checkpatch.pl warning: "Comparisons should place the constant on the right side of the test" Signed-off-by: Vardhan H G <crazylonestar7@gmail.com> Link: https://lore.kernel.org/r/20210407061749.13460-1-crazylonestar7@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-07ALSA: aloop: Fix initialization of controlsJonas Holmberg
Add a control to the card before copying the id so that the numid field is initialized in the copy. Otherwise the numid field of active_id, format_id, rate_id and channels_id will be the same (0) and snd_ctl_notify() will not queue the events properly. Signed-off-by: Jonas Holmberg <jonashg@axis.com> Reviewed-by: Jaroslav Kysela <perex@perex.cz> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210407075428.2666787-1-jonashg@axis.com Signed-off-by: Takashi Iwai <tiwai@suse.de>
2021-04-07staging: rtl8192u: remove unused variableJiapeng Chong
Fix the following gcc warning: drivers/staging/rtl8192u/r8192U_core.c:3419:6: warning: variable ‘reset_status’ set but not used [-Wunused-but-set-variable]. Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Link: https://lore.kernel.org/r/1617775650-42645-1-git-send-email-jiapeng.chong@linux.alibaba.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-07staging: rtl8192e: rtl8192E_dev: remove unused variableJiapeng Chong
Fix the following gcc warning: drivers/staging/rtl8192e/rtl8192e/r8192E_dev.c:693:15: warning: variable ‘tmpRegC’ set but not used [-Wunused-but-set-variable]. Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Link: https://lore.kernel.org/r/1617767558-114050-1-git-send-email-jiapeng.chong@linux.alibaba.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-07staging: rtl8712: Use constants from <linux/ieee80211.h>Christophe JAILLET
Some constants defined in wifi.h are already defined in <linux/ieee80211.h> with some other (but similar) names. Be consistent and use the ones from <linux/ieee80211.h>. The conversions made are: _SSID_IE_ --> WLAN_EID_SSID _SUPPORTEDRATES_IE_ --> WLAN_EID_SUPP_RATES _DSSET_IE_ --> WLAN_EID_DS_PARAMS _IBSS_PARA_IE_ --> WLAN_EID_IBSS_PARAMS _ERPINFO_IE_ --> WLAN_EID_ERP_INFO _EXT_SUPPORTEDRATES_IE_ --> WLAN_EID_EXT_SUPP_RATES _HT_CAPABILITY_IE_ --> WLAN_EID_HT_CAPABILITY _HT_EXTRA_INFO_IE_ --> WLAN_EID_HT_OPERATION (not used) _HT_ADD_INFO_IE_ --> WLAN_EID_HT_OPERATION _VENDOR_SPECIFIC_IE_ --> WLAN_EID_VENDOR_SPECIFIC _RESERVED47_ --> (not used) Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/fe35fb45323adc3a30f31b7280cec7700fd325d8.1617741313.git.christophe.jaillet@wanadoo.fr Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-07staging: rtl8723bs: core: Move constants to the right of comparisonZhansaya Bagdauletkyzy
Move constant variables to the right side of comparisons to increase consistency with Linux kernel code base. Reported by checkpatch. Signed-off-by: Zhansaya Bagdauletkyzy <zhansayabagdaulet@gmail.com> Link: https://lore.kernel.org/r/20210406161131.GA103324@zhans Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-07staging: rtl8723bs: hal: Add spaces around operator in HalBtc8723b1Ant.hFabio M. De Francesco
Added spaces around operators in file HalBtc8723b1Ant.h. Issue detected by checkpatch.pl. Spaces are preferred to improve readibility. Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com> Link: https://lore.kernel.org/r/20210406164001.13646-1-fmdefrancesco@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-07staging: rtl8723bs: hal: Add spaces around operators in HalBtc8723b2Ant.cFabio M. De Francesco
Added spaces around operators in file HalBtc8723b2Ant.c. Issue detected by checkpatch.pl. Spaces are preferred to improve readibility. Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com> Link: https://lore.kernel.org/r/20210406170011.20753-1-fmdefrancesco@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit (git 2.34.1) at 2025-09-23 20:32:10 +0000