| Age | Commit message (Collapse) | Author |
|---|
|
Pull documentation fixes from Jonathan Corbet:
"Four small documentation fixes"
* tag 'docs-6.9-fixes' of git://git.lwn.net/linux:
docs: zswap: fix shell command format
tracing: Fix documentation on tp_printk cmdline option
docs: Fix bitfield handling in kernel-doc
Documentation: dev-tools: Add link to RV docs
|
|
Some laptops where the thermal control is handled by the EC may
provide trip points that fail the kernels new validation, but still have
working temperature sensors. An example of this is the Framework 13 AMD.
This patch allows the thermal zone to still be registered without trip
points if the trip points fail validation, allowing the temperature
sensor to be viewed and used by the user.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218586
Fixes: 9c8647224e9f ("ACPI: thermal: Use library functions to obtain trip point temperature values")
Signed-off-by: Stephen Horvath <s.horvath@outlook.com.au>
[ rjw: Subject edits, remove redundant braces ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull bcachefs fixes from Kent Overstreet:
"Lots of fixes for situations with extreme filesystem damage.
One fix ("Fix journal pins in btree write buffer") applicable to
normal usage; also a dio performance fix.
New repair/construction code is in the final stages, should be ready
in about a week. Anyone that lost btree interior nodes (or a variety
of other damage) as a result of the splitbrain bug will be able to
repair then"
* tag 'bcachefs-2024-04-01' of https://evilpiepirate.org/git/bcachefs: (32 commits)
bcachefs: On emergency shutdown, print out current journal sequence number
bcachefs: Fix overlapping extent repair
bcachefs: Fix remove_dirent()
bcachefs: Logged op errors should be ignored
bcachefs: Improve -o norecovery; opts.recovery_pass_limit
bcachefs: bch2_run_explicit_recovery_pass_persistent()
bcachefs: Ensure bch_sb_field_ext always exists
bcachefs: Flush journal immediately after replay if we did early repair
bcachefs: Resume logged ops after fsck
bcachefs: Add error messages to logged ops fns
bcachefs: Split out recovery_passes.c
bcachefs: fix backpointer for missing alloc key msg
bcachefs: Fix bch2_btree_increase_depth()
bcachefs: Kill bch2_bkey_ptr_data_type()
bcachefs: Fix use after free in check_root_trans()
bcachefs: Fix repair path for missing indirect extents
bcachefs: Fix use after free in bch2_check_fix_ptrs()
bcachefs: Fix btree node keys accounting in topology repair path
bcachefs: Check btree ptr min_key in .invalid
bcachefs: add REQ_SYNC and REQ_IDLE in write dio
...
|
|
mean_and_variance_test_2 and mean_and_variance_test_4 always fail.
The input parameters to those tests are identical to the input parameters
to tests 1 and 3, yet the expected result for tests 2 and 4 is different
for the mean and stddev tests. That will always fail.
Expected mean_and_variance_get_mean(mv) == mean[i], but
mean_and_variance_get_mean(mv) == 22 (0x16)
mean[i] == 10 (0xa)
Drop the bad tests.
Fixes: 65bc41090720 ("mean and variance: More tests")
Closes: https://lore.kernel.org/lkml/065b94eb-6a24-4248-b7d7-d3212efb4787@roeck-us.net/
Cc: Kent Overstreet <kent.overstreet@linux.dev>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
It is possible to clear a root's IN_TRANS tag from the radix tree, but
not clear its PERTRANS, if there is some error in between. Eliminate
that possibility by moving the free up to where we clear the tag.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Boris Burkov <boris@bur.io>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Currently, this call site in btrfs_clear_delalloc_extent() only converts
the reservation. We are marking it not delalloc, so I don't think it
makes sense to keep the rsv around. This is a path where we are not
sure to join a transaction, so it leads to incorrect free-ing during
umount.
Helps with the pass rate of generic/269 and generic/475.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Boris Burkov <boris@bur.io>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
The transaction is only able to free PERTRANS reservations for a root
once that root has been recorded with the TRANS tag on the roots radix
tree. Therefore, until we are sure that this root will get tagged, it
isn't safe to convert. Generally, this is not an issue as *some*
transaction will likely tag the root before long and this reservation
will get freed in that transaction, but technically it could stick
around until unmount and result in a warning about leaked metadata
reservation space.
This path is most exercised by running the generic/269 fstest with
CONFIG_BTRFS_DEBUG.
Fixes: a6496849671a ("btrfs: fix start transaction qgroup rsv double free")
CC: stable@vger.kernel.org # 6.6+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Boris Burkov <boris@bur.io>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
When running delayed inode updates, we do not record the inode's root in
the transaction, but we do allocate PREALLOC and thus converted PERTRANS
space for it. To be sure we free that PERTRANS meta rsv, we must ensure
that we record the root in the transaction.
Fixes: 4f5427ccce5d ("btrfs: delayed-inode: Use new qgroup meta rsv for delayed inode and item")
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Boris Burkov <boris@bur.io>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Create subvolume, create snapshot and delete subvolume all use
btrfs_subvolume_reserve_metadata() to reserve metadata for the changes
done to the parent subvolume's fs tree, which cannot be mediated in the
normal way via start_transaction. When quota groups (squota or qgroups)
are enabled, this reserves qgroup metadata of type PREALLOC. Once the
operation is associated to a transaction, we convert PREALLOC to
PERTRANS, which gets cleared in bulk at the end of the transaction.
However, the error paths of these three operations were not implementing
this lifecycle correctly. They unconditionally converted the PREALLOC to
PERTRANS in a generic cleanup step regardless of errors or whether the
operation was fully associated to a transaction or not. This resulted in
error paths occasionally converting this rsv to PERTRANS without calling
record_root_in_trans successfully, which meant that unless that root got
recorded in the transaction by some other thread, the end of the
transaction would not free that root's PERTRANS, leaking it. Ultimately,
this resulted in hitting a WARN in CONFIG_BTRFS_DEBUG builds at unmount
for the leaked reservation.
The fix is to ensure that every qgroup PREALLOC reservation observes the
following properties:
1. any failure before record_root_in_trans is called successfully
results in freeing the PREALLOC reservation.
2. after record_root_in_trans, we convert to PERTRANS, and now the
transaction owns freeing the reservation.
This patch enforces those properties on the three operations. Without
it, generic/269 with squotas enabled at mkfs time would fail in ~5-10
runs on my system. With this patch, it ran successfully 1000 times in a
row.
Fixes: e85fde5162bf ("btrfs: qgroup: fix qgroup meta rsv leak for subvolume operations")
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Boris Burkov <boris@bur.io>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
We use add_root_meta_rsv and sub_root_meta_rsv to track prealloc and
pertrans reservations for subvolumes when quotas are enabled. The
convert function does not properly increment pertrans after decrementing
prealloc, so the count is not accurate.
Note: we check that the fs is not read-only to mirror the logic in
qgroup_convert_meta, which checks that before adding to the pertrans rsv.
Fixes: 8287475a2055 ("btrfs: qgroup: Use root::qgroup_meta_rsv_* to record qgroup meta reserved space")
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Boris Burkov <boris@bur.io>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
If user request --no-msr or is not able to access the MSRs,
turbostat should clear all the counters added with --add.
Because MSR access permission checks are done after the cmdline is
parsed, the decision has to be defered up until the transition into
no-msr mode happen.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Checking early if the permissions are even needed gets rid of the
warnings about some of them missing. Earlier we issued a warning in case
of missing MSR and/or perf permissions, even when user never asked for
counters that require those.
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
To allow unprivileged user to run turbostat seamlessly.
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
By using the perf API we spend less time in between the reads of the
counters, resulting in more accurate calculations of the dependent
metrics.
Using perf API is also usually faster overall, although cache miss, if
we get one, is more costly when using perf vs MSR driver.
We would fallback to the msr reads if the sysfs isn't there or when in
--no-perf mode.
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add the --no-perf option to allow users to run turbostat without
accessing perf.
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add --no-msr option to allow users to run turbostat without
accessing MSRs via the MSR driver.
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Eliminate redundant debug output for core and package scope counters.
Include name and path for all "ADDED" counters.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Previously a failed read of /dev/cpu_dma_latency erroneously complained
turbostat: capget(CAP_SYS_ADMIN) failed, try "# setcap cap_sys_admin=ep ./turbostat
This went unnoticed because this file is typically visible to root,
and turbostat was typically run as root.
Going forward, when a non-root user can run turbostat...
Complain about failed read access to this file only if --debug is used.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
If MSRs cannot be read, values can be obtained from cpuid.
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
HEAD
KVM/riscv fixes for 6.9, take #1
- Fix spelling mistake in arch_timer selftest
- Remove redundant semicolon in num_isa_ext_regs()
- Fix APLIC setipnum_le/be write emulation
- Fix APLIC in_clrip[x] read emulation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 6.9, part #1
- Ensure perf events programmed to count during guest execution
are actually enabled before entering the guest in the nVHE
configuration.
- Restore out-of-range handler for stage-2 translation faults.
- Several fixes to stage-2 TLB invalidations to avoid stale
translations, possibly including partial walk caches.
- Fix early handling of architectural VHE-only systems to ensure E2H is
appropriately set.
- Correct a format specifier warning in the arch_timer selftest.
- Make the KVM banner message correctly handle all of the possible
configurations.
|
|
nvme_update_zone_info does (admin queue) I/O to the device and can fail.
We fail to abort the queue limits update if that happen, but really
should avoid with the frozen I/O queue as much as possible anyway.
Split the logic into a helper to query the information that can be
called on an unfrozen queue and one to apply it to the queue limits.
Fixes: 9b130d681443 ("nvme: use the atomic queue limits update API")
Reported-by: Kanchan Joshi <joshi.k@samsung.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Serialise cifs_construct_tcon() with cifs_mount_mutex to handle
parallel mounts that may end up reusing the session and tcon created
by it.
Cc: stable@vger.kernel.org # 6.4+
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
The tcons created by cifs_construct_tcon() on multiuser mounts must
also be able to failover and refresh DFS referrals, so set the
appropriate fields in order to get a full DFS tcon. They could be
shared among different superblocks later, too.
Cc: stable@vger.kernel.org # 6.4+
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202404021518.3Xu2VU4s-lkp@intel.com/
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Avoid refreshing DFS referral with refpath_lock acquired as the I/O
could block for a while due to a potentially disconnected or slow DFS
root server and then making other threads - that use same @server and
don't require a DFS root server - unable to make any progress.
Cc: stable@vger.kernel.org # 6.4+
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Avoid potential use-after-free bugs when walking DFS referrals,
mounting and performing DFS failover by ensuring that all children
from parent @tcon->ses are also refcounted. They're all needed across
the entire DFS mount. Get rid of @tcon->dfs_ses_list while we're at
it, too.
Cc: stable@vger.kernel.org # 6.4+
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202404021527.ZlRkIxgv-lkp@intel.com/
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Sometimes the readout of /sys/kernel/debug/swiotlb/io_tlb_used and
io_tlb_used_hiwater can be a huge number (e.g. 18446744073709551615),
which is actually a negative number if we use "%ld" to print the number.
When swiotlb_create_default_debugfs() is running from late_initcall,
mem->total_used may already be non-zero, because the storage driver
may have already started to perform I/O operations: if the storage
driver is built-in, its probe() callback is called before late_initcall.
swiotlb_create_debugfs_files() should not blindly set mem->total_used
and mem->used_hiwater to 0; actually it doesn't have to initialize the
fields at all, because the fields, as part of the global struct
io_tlb_default_mem, have been implicitly initialized to zero.
Also don't explicitly set mem->transient_nslabs to 0.
Fixes: 8b0977ecc8b3 ("swiotlb: track and report io_tlb_used high water marks in debugfs")
Fixes: 02e765697038 ("swiotlb: add debugfs to track swiotlb transient pool usage")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: ZhangPeng <zhangpeng362@huawei.com>
Reviewed-by: Petr Tesarik <petr.tesarik1@huawei-partners.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
In current code, swiotlb_bounce() may do partial sync's correctly in
some circumstances, but may incorrectly fail in other circumstances.
The failure cases require both of these to be true:
1) swiotlb_align_offset() returns a non-zero "offset" value
2) the tlb_addr of the partial sync area points into the first
"offset" bytes of the _second_ or subsequent swiotlb slot allocated
for the mapping
Code added in commit 868c9ddc182b ("swiotlb: add overflow checks
to swiotlb_bounce") attempts to WARN on the invalid case where
tlb_addr points into the first "offset" bytes of the _first_
allocated slot. But there's no way for swiotlb_bounce() to distinguish
the first slot from the second and subsequent slots, so the WARN
can be triggered incorrectly when #2 above is true.
Related, current code calculates an adjustment to the orig_addr stored
in the swiotlb slot. The adjustment compensates for the difference
in the tlb_addr used for the partial sync vs. the tlb_addr for the full
mapping. The adjustment is stored in the local variable tlb_offset.
But when #1 and #2 above are true, it's valid for this adjustment to
be negative. In such case the arithmetic to adjust orig_addr produces
the wrong result due to tlb_offset being declared as unsigned.
Fix these problems by removing the over-constraining validations added
in 868c9ddc182b. Change the declaration of tlb_offset to be signed
instead of unsigned so the adjustment arithmetic works correctly.
Tested with a test-only hack to how swiotlb_tbl_map_single() calls
swiotlb_bounce(). Instead of calling swiotlb_bounce() just once
for the entire mapped area, do a loop with each iteration doing
only a 128 byte partial sync until the entire mapped area is
sync'ed. Then with swiotlb=force on the kernel boot line, run a
variety of raw disk writes followed by read and verification of
all bytes of the written data. The storage device has DMA
min_align_mask set, and the writes are done with a variety of
original buffer memory address alignments and overall buffer
sizes. For many of the combinations, current code triggers the
WARN statements, or the data verification fails. With the fixes,
no WARNs occur and all verifications pass.
Fixes: 5f89468e2f06 ("swiotlb: manipulate orig_addr when tlb_addr has offset")
Fixes: 868c9ddc182b ("swiotlb: add overflow checks to swiotlb_bounce")
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Dominique Martinet <dominique.martinet@atmark-techno.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Allow a buffer pre-padding of up to alloc_align_mask, even if it requires
allocating additional IO TLB slots.
If the allocation alignment is bigger than IO_TLB_SIZE and min_align_mask
covers any non-zero bits in the original address between IO_TLB_SIZE and
alloc_align_mask, these bits are not preserved in the swiotlb buffer
address.
To fix this case, increase the allocation size and use a larger offset
within the allocated buffer. As a result, extra padding slots may be
allocated before the mapping start address.
Leave orig_addr in these padding slots initialized to INVALID_PHYS_ADDR.
These slots do not correspond to any CPU buffer, so attempts to sync the
data should be ignored.
The padding slots should be automatically released when the buffer is
unmapped. However, swiotlb_tbl_unmap_single() takes only the address of the
DMA buffer slot, not the first padding slot. Save the number of padding
slots in struct io_tlb_slot and use it to adjust the slot index in
swiotlb_release_slots(), so all allocated slots are properly freed.
Fixes: 2fd4fa5d3fb5 ("swiotlb: Fix alignment checks when both allocation and DMA masks are present")
Link: https://lore.kernel.org/linux-iommu/20240311210507.217daf8b@meshulam.tesarici.cz/
Signed-off-by: Petr Tesarik <petr.tesarik1@huawei-partners.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Linux 6.9 made the nvme multipath nodes not properly pick up changes when
the LBA size goes smaller after an nvme format. This is because we now
try to inherit the queue settings for the multipath node entirely from
the individual paths. That is the right thing to do for I/O size
limitations, which make up most of the queue limits, but it is wrong for
changes to the namespace configuration, where we do want to pick up the
new format, which will eventually show up on all paths once they are
re-queried.
Fix this by not inheriting the block size and related fields and always
for updating them.
Fixes: 8f03cfa117e0 ("nvme: don't use nvme_update_disk_info for the multipath disk")
Reported-by: Nilay Shroff <nilay@linux.ibm.com>
Tested-by: Nilay Shroff <nilay@linux.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Modpost warns about missing module description, add it.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://msgid.link/r/20240402130640.3310999-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We removed the configuration of ES8326_ADC_SCALE
in es8326_jack_detect_handler because user changed
the configuration by snd_controls
Signed-off-by: Zhang Yi <zhangyi@everest-semi.com>
Link: https://msgid.link/r/20240402062043.20608-5-zhangyi@everest-semi.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We got a headphone detection issue after suspend and resume.
And we fixed it by modifying the configuration at es8326_suspend
and invoke es8326_irq at es8326_resume.
Signed-off-by: Zhang Yi <zhangyi@everest-semi.com>
Link: https://msgid.link/r/20240402062043.20608-4-zhangyi@everest-semi.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We got a digital microphone feature issue. And we fixed it by modifying
the clock table. Also, we changed the marco ES8326_CLK_ON declaration
Signed-off-by: Zhang Yi <zhangyi@everest-semi.com>
Link: https://msgid.link/r/20240402062043.20608-3-zhangyi@everest-semi.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We got an error report about headphone type detection and button detection.
We fixed the headphone type detection error by adjusting the debounce timer
configuration. And we fixed the button detection error by disabling the
button detection feature when the headphone are unplugged and enabling it
when headphone are plugged in.
Signed-off-by: Zhang Yi <zhangyi@everest-semi.com>
Link: https://msgid.link/r/20240402062043.20608-2-zhangyi@everest-semi.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
'no-emmc' is not a valid property.
The original intention was to use the 'no-mmc' property.
Change it accordingly to fix the following dt-schema warning:
imx7s-mba7.dtb: mmc@30b40000: Unevaluated properties are not allowed ('no-emmc' was unexpected)
Fixes: d430a7e0e181 ("ARM: dts: imx7-mba7: restrict usdhc interface modes")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
syzkaller started using corpuses where a BPF tracing program deletes
elements from a sockmap/sockhash map. Because BPF tracing programs can be
invoked from any interrupt context, locks taken during a map_delete_elem
operation must be hardirq-safe. Otherwise a deadlock due to lock inversion
is possible, as reported by lockdep:
CPU0 CPU1
---- ----
lock(&htab->buckets[i].lock);
local_irq_disable();
lock(&host->lock);
lock(&htab->buckets[i].lock);
<Interrupt>
lock(&host->lock);
Locks in sockmap are hardirq-unsafe by design. We expects elements to be
deleted from sockmap/sockhash only in task (normal) context with interrupts
enabled, or in softirq context.
Detect when map_delete_elem operation is invoked from a context which is
_not_ hardirq-unsafe, that is interrupts are disabled, and bail out with an
error.
Note that map updates are not affected by this issue. BPF verifier does not
allow updating sockmap/sockhash from a BPF tracing program today.
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface")
Reported-by: xingwei lee <xrivendell7@gmail.com>
Reported-by: yue sun <samsun1006219@gmail.com>
Reported-by: syzbot+bc922f476bd65abbd466@syzkaller.appspotmail.com
Reported-by: syzbot+d4066896495db380182e@syzkaller.appspotmail.com
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: syzbot+d4066896495db380182e@syzkaller.appspotmail.com
Acked-by: John Fastabend <john.fastabend@gmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=d4066896495db380182e
Closes: https://syzkaller.appspot.com/bug?extid=bc922f476bd65abbd466
Link: https://lore.kernel.org/bpf/20240402104621.1050319-1-jakub@cloudflare.com
|
|
When we're engaged in local caching of a cifs filesystem, we cannot perform
caching of a partially written cache granule unless we can read the rest of
the granule. This can result in unexpected access errors being reported to
the user.
Fix this by the following: if a file is opened O_WRONLY locally, but the
mount was given the "-o fsc" flag, try first opening the remote file with
GENERIC_READ|GENERIC_WRITE and if that returns -EACCES, try dropping the
GENERIC_READ and doing the open again. If that last succeeds, invalidate
the cache for that file as for O_DIRECT.
Fixes: 70431bfd825d ("cifs: Support fscache indexing rewrite")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Steve French <sfrench@samba.org>
cc: Shyam Prasad N <nspmangalore@gmail.com>
cc: Rohith Surabattula <rohiths.msft@gmail.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
UHBR13.5 is not supported in MTL and also the DP2.1 spec says UHBR13.5
is optional. Hence removing UHBR135 from the supported link rates.
v2: Reframed the commit message and added link to the issue.
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Fixes: 62618c7f117e ("drm/i915/mtl: C20 PLL programming")
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240228144350.3184930-1-arun.r.murthy@intel.com
(cherry picked from commit ddf8a8bbb5643265883bab0c59adf0648422c4bb)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Commit 0848814aa296 ("drm/i915/dp: Fix connector DSC HW state readout")
moved the DSC HW state readout to a connector specific hook, however
only added the hook for DP MST connectors, not for DP SST ones. Fix
adding the hook for SST connectors as well.
This fixes the following warn on platforms where BIOS enables DSC:
[ 66.208601] i915 0000:00:02.0: drm_WARN_ON(!connector->dp.dsc_decompression_aux || !connector->dp.dsc_decompression_enabled)
...
[ 66.209024] RIP: 0010:intel_dp_sink_disable_decompression+0x76/0x110 [i915]
...
[ 66.209333] ? intel_dp_sink_disable_decompression+0x76/0x110 [i915]
...
[ 66.210068] intel_disable_ddi+0x135/0x1d0 [i915]
[ 66.210302] intel_encoders_disable+0x9b/0xc0 [i915]
[ 66.210565] hsw_crtc_disable+0x153/0x170 [i915]
[ 66.210823] intel_old_crtc_state_disables+0x52/0xb0 [i915]
[ 66.211107] intel_atomic_commit_tail+0x5cf/0x1330 [i915]
[ 66.211366] intel_atomic_commit+0x39d/0x3f0 [i915]
[ 66.211612] ? intel_atomic_commit+0x39d/0x3f0 [i915]
[ 66.211872] drm_atomic_commit+0x9d/0xd0 [drm]
[ 66.211921] ? __pfx___drm_printfn_info+0x10/0x10 [drm]
[ 66.211975] intel_initial_commit+0x1a8/0x260 [i915]
[ 66.212234] intel_display_driver_probe+0x2a/0x80 [i915]
[ 66.212479] i915_driver_probe+0x7c6/0xc60 [i915]
[ 66.212664] ? drm_privacy_screen_get+0x168/0x190 [drm]
[ 66.212711] i915_pci_probe+0xe2/0x1c0 [i915]
Fixes: 0848814aa296 ("drm/i915/dp: Fix connector DSC HW state readout")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10410
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240311145626.2454923-1-imre.deak@intel.com
(cherry picked from commit 7a51a2aa2384ea8bee76698ae586a2bea5b8ddb5)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
SMB2_GLOBAL_CAP_ENCRYPTION flag should be used only for 3.0 and
3.0.2 dialects. This flags set cause compatibility problems with
other SMB clients.
Reported-by: James Christopher Adduono <jc@adduono.com>
Tested-by: James Christopher Adduono <jc@adduono.com>
Cc: stable@vger.kernel.org
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
If installing malicious ksmbd-tools, ksmbd.mountd can return invalid ipc
response to ksmbd kernel server. ksmbd should validate payload size of
ipc response from ksmbd.mountd to avoid memory overrun or
slab-out-of-bounds. This patch validate 3 ipc response that has payload.
Cc: stable@vger.kernel.org
Reported-by: Chao Ma <machao2019@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Don't send oplock break if rename fails. This patch fix
smb2.oplock.batch20 test.
Cc: stable@vger.kernel.org
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
There is no check for overflow of 'start + len' in blk_ioctl_discard().
Hung task occurs if submit an discard ioctl with the following param:
start = 0x80000000000ff000, len = 0x8000000000fff000;
Add the overflow validation now.
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240329012319.2034550-1-linan666@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In null_add_dev(), if an error happen after initializing the resources
for a zoned null block device, we must free these resources before
exiting the function. To ensure this, move the out_cleanup_zone label
after out_cleanup_disk as we jump to this latter label if an error
happens after calling null_init_zoned_dev().
Fixes: e440626b1caf ("null_blk: pass queue_limits to blk_mq_alloc_disk")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240330005300.1503252-1-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Rather than use the system unbound event workqueue, use an io_uring
specific one. This avoids dependencies with the tty, which also uses
the system_unbound_wq, and issues flushes of said workqueue from inside
its poll handling.
Cc: stable@vger.kernel.org
Reported-by: Rasmus Karlsson <rasmus.karlsson@pajlada.com>
Tested-by: Rasmus Karlsson <rasmus.karlsson@pajlada.com>
Tested-by: Iskren Chernev <me@iskren.info>
Link: https://github.com/axboe/liburing/issues/1113
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
For shutting up spurious KMSAN uninit-value warnings, just replace
kmalloc() calls with kzalloc() for the buffers used for
communications. There should be no real issue with the original code,
but it's still better to cover.
Reported-by: syzbot+7fb05ccf7b3d2f9617b3@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/r/00000000000084b18706150bcca5@google.com
Message-ID: <20240402063628.26609-1-tiwai@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The actual clock show wrong frequency:
echo on >/sys/devices/platform/bus\@5b000000/5b010000.mmc/power/control
cat /sys/kernel/debug/mmc0/ios
clock: 200000000 Hz
actual clock: 166000000 Hz
^^^^^^^^^
.....
According to
sdhc0_lpcg: clock-controller@5b200000 {
compatible = "fsl,imx8qxp-lpcg";
reg = <0x5b200000 0x10000>;
#clock-cells = <1>;
clocks = <&clk IMX_SC_R_SDHC_0 IMX_SC_PM_CLK_PER>,
<&conn_ipg_clk>, <&conn_axi_clk>;
clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>,
<IMX_LPCG_CLK_5>;
clock-output-names = "sdhc0_lpcg_per_clk",
"sdhc0_lpcg_ipg_clk",
"sdhc0_lpcg_ahb_clk";
power-domains = <&pd IMX_SC_R_SDHC_0>;
}
"per_clk" should be IMX_LPCG_CLK_0 instead of IMX_LPCG_CLK_5.
After correct clocks order:
echo on >/sys/devices/platform/bus\@5b000000/5b010000.mmc/power/control
cat /sys/kernel/debug/mmc0/ios
clock: 200000000 Hz
actual clock: 198000000 Hz
^^^^^^^^
...
Fixes: 16c4ea7501b1 ("arm64: dts: imx8: switch to new lpcg clock binding")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fixes the realtek quirk to initialise the Cirrus amp correctly and adds
related quirk for missing DSD properties. This model laptop has slightly
updated internals compared to the previous version with Realtek Codec
ID of 0x1caf.
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Cc: <stable@vger.kernel.org>
Message-ID: <20240402015126.21115-1-luke@ljones.dev>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
