| Age | Commit message (Collapse) | Author |
|---|
|
...rather than kilo-PTE.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Apply s/Usabel/usable/ bikeshed suggested by Ben Widawsky.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This fixes a regression for SDVO from
commit fbfcc4f3a0cf8bbde87646b74241faa8e37426bf
Author: Jani Nikula <jani.nikula@intel.com>
Date: Mon Oct 22 16:12:18 2012 +0300
drm/i915/sdvo: restore i2c adapter config on intel_sdvo_init() failures
As SDVOB and SDVOC are multiplexed on the same pin, if a chipset does
not have the second SDVO encoder, it will then remove the force-bit
setting on the common i2c adapter during teardown. All subsequent
attempts of trying to use GMBUS with SDVOB then fail.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: fixup inversion in the debug printout, noticed by Jani
Nikulai.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The CBUS UART's interrupt number was wrong conflicting with the interrupt
being tied to the Intel PIIX4. Since the PIIX4's interrupt is registered
before the CBUS UART which is not being used on most systems this would
not be noticed.
Attempts to open the ttyS2 CBUS UART would result in:
genirq: Flags mismatch irq 18. 00000000 (serial) vs. 00010000 (XT-PIC cascade)
serial_link_irq_chain: request failed: -16 for irq: 18
Qemu was written to match the kernel so will need to be fixed also.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
SATA MICROCODE DOWNALOAD fails on isci driver. After receiving Register
Device to Host (FIS 0x34) frame Initiator resets phy.
In the frame handler routine response (FIS 0x34) was copied into wrong
buffer and upper layer did not receive any answer which resulted in
timeout and reset.
This patch corrects this bug.
Signed-off-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
There are laptops out there that need the eDP bpc from VBT. This is
effectively a revert of
commit 4344b813f105a19f793f1fd93ad775b784648b95
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Aug 10 11:10:20 2012 +0200
drm/i915: ignore eDP bpc settings from vbt
but putting the VBT check after the EDID check to see them both in dmesg if
this clamps more than the EDID. We have enough history with bpc clamping to
warrant the extra debug info.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47641
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=56401
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Select HAVE_ALIGNED_STRUCT_PAGE on s390, so that the slub allocator can make
use of compare and swap double for lockless updates. This increases the size
of struct page to 64 bytes (instead of 56 bytes), however the performance gain
justifies the increased size:
- now excactly four struct pages fit into a single cache line; the
case that accessing a struct page causes two cache line loads
does not exist anymore.
- calculating the offset of a struct page within the memmap array
is only a simple shift instead of a more expensive multiplication.
A "hackbench 200 process 200" run on a 32 cpu system did show an 8% runtime
improvement.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
access_ok() returns always "true" on s390. Therefore all access_ok()
invocations are rather pointless.
However when walking page tables we need to make sure that everything
is within bounds of the ASCE limit of the task's address space.
So remove the access_ok() call and add the same check we have in
get_user_pages_fast().
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
When walking page tables we need to make sure that everything
is within bounds of the ASCE limit of the task's address space.
Otherwise we might calculate e.g. a pud pointer which is not
within a pud and dereference it.
So check against TASK_SIZE (which is the ASCE limit) before
walking page tables.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The xfrm gc threshold value depends on ip_rt_max_size. This
value was set to INT_MAX with the routing cache removal patch,
so we start doing garbage collecting when we have INT_MAX/2
IPsec routes cached. Fix this by going back to the static
threshold of 1024 routes.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
I don't think this works as intended. '|' higher precedence than ?: so
the bitwize OR "0 | (val & STR_MOST)" is a no-op.
I have re-written it to be more clear.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.7
A few small fixes plus a large but simple change for WM5102 which writes
out a bunch of register updates to the device when we enable the clock
as recommended following chip evaluation.
|
|
In case of probe deferral, the allocated GPIO line is not freed, which
prevents it from being claimed and properly asserted in later attempts.
Fix this by using devm_gpio_request().
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Michael Hirsch <hirsch@teufel.de>
Cc: Alexander Sverdlin <subaparts@yandex.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
'fix/samsung' and 'fix/wm8978' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into tmp
|
|
Pull KVM fix from Marcelo Tosatti:
"A correction for user triggerable oops"
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: invalid opcode oops on SET_SREGS with OSXSAVE bit set (CVE-2012-4461)
|
|
Pull ux500 clk fixes from Mike Turquette:
"Missing clkdev entries are causing regressions on the U8500 platform.
This pull request contains those missing clkdev entries which are
needed to boot that platform."
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: ux500: Register slimbus clock lookups for u8500
clk: ux500: Update rtc clock lookup for u8500
clk: ux500: Register msp clock lookups for u8500
clk: ux500: Register ssp clock lookups for u8500
clk: ux500: Register i2c clock lookups for u8500
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull menuconfig portability fix from Michal Marek:
"Here is a fix for v3.7 that makes menuconfig compile again on systems
whose C library is lacking CIRCLEQ_* macros. I thought I sent it
earlier, but apparently I did not."
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
menuconfig: Replace CIRCLEQ by list_head-style lists.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds
Pull LED fix from Bryan Wu.
* 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
ledtrig-cpu: kill useless mutex to fix sleep in atomic context
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull futex fix from Thomas Gleixner:
"Single fix for a long standing futex race when taking over a futex
whose owner died. You can end up with two owners, which violates
quite some rules."
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Handle futex_pi OWNER_DIED take over correctly
|
|
On hosts without the XSAVE support unprivileged local user can trigger
oops similar to the one below by setting X86_CR4_OSXSAVE bit in guest
cr4 register using KVM_SET_SREGS ioctl and later issuing KVM_RUN
ioctl.
invalid opcode: 0000 [#2] SMP
Modules linked in: tun ip6table_filter ip6_tables ebtable_nat ebtables
...
Pid: 24935, comm: zoog_kvm_monito Tainted: G D 3.2.0-3-686-pae
EIP: 0060:[<f8b9550c>] EFLAGS: 00210246 CPU: 0
EIP is at kvm_arch_vcpu_ioctl_run+0x92a/0xd13 [kvm]
EAX: 00000001 EBX: 000f387e ECX: 00000000 EDX: 00000000
ESI: 00000000 EDI: 00000000 EBP: ef5a0060 ESP: d7c63e70
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process zoog_kvm_monito (pid: 24935, ti=d7c62000 task=ed84a0c0
task.ti=d7c62000)
Stack:
00000001 f70a1200 f8b940a9 ef5a0060 00000000 00200202 f8769009 00000000
ef5a0060 000f387e eda5c020 8722f9c8 00015bae 00000000 ed84a0c0 ed84a0c0
c12bf02d 0000ae80 ef7f8740 fffffffb f359b740 ef5a0060 f8b85dc1 0000ae80
Call Trace:
[<f8b940a9>] ? kvm_arch_vcpu_ioctl_set_sregs+0x2fe/0x308 [kvm]
...
[<c12bfb44>] ? syscall_call+0x7/0xb
Code: 89 e8 e8 14 ee ff ff ba 00 00 04 00 89 e8 e8 98 48 ff ff 85 c0 74
1e 83 7d 48 00 75 18 8b 85 08 07 00 00 31 c9 8b 95 0c 07 00 00 <0f> 01
d1 c7 45 48 01 00 00 00 c7 45 1c 01 00 00 00 0f ae f0 89
EIP: [<f8b9550c>] kvm_arch_vcpu_ioctl_run+0x92a/0xd13 [kvm] SS:ESP
0068:d7c63e70
QEMU first retrieves the supported features via KVM_GET_SUPPORTED_CPUID
and then sets them later. So guest's X86_FEATURE_XSAVE should be masked
out on hosts without X86_FEATURE_XSAVE, making kvm_set_cr4 with
X86_CR4_OSXSAVE fail. Userspaces that allow specifying guest cpuid with
X86_FEATURE_XSAVE even on hosts that do not support it, might be
susceptible to this attack from inside the guest as well.
Allow setting X86_CR4_OSXSAVE bit only if host has XSAVE support.
Signed-off-by: Petr Matousek <pmatouse@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Since commit edc88ceb0 (ARM: be really quiet when building with 'make -s') the
following output is generated when building a kernel for ARM:
echo ' Kernel: arch/arm/boot/Image is ready'
Kernel: arch/arm/boot/Image is ready
Building modules, stage 2.
echo ' Kernel: arch/arm/boot/zImage is ready'
Kernel: arch/arm/boot/zImage is ready
As per Documentation/kbuild/makefiles.txt the correct way of using kecho is
'@$(kecho)'.
Make this change so no more unwanted 'echo' messages are displayed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
On OMAP4 boards using the TWL6030 PMIC, the sys_drm_msecure is
connected to the MSECURE input of the TWL6030 PMIC. This signal
controls the secure-mode operation of the PMIC. If its not mux'd
correctly, some functionality of the PMIC will not be accessible since
the PMIC will be in secure mode.
For example, if the TWL RTC is in secure mode, most of its registers
are read-only, meaning (re)programming the RTC (e.g. for wakeup from
suspend) will fail.
To fix, ensure the signal is properly mux'd as output when TWL is
intialized.
This fix is required when using recent versions of u-boot (>= v2012.04.01)
since u-boot is no longer setting the default mux for this pin.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren <tony@atomide.com>:
Minor OMAP PM and hwmod fixes for v3.7-rc series via
Kevin Hilman and Paul Walmsley.
* tag 'omap-for-v3.7-rc4/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: PM: fix regulator name for VDD_MPU
ARM: OMAP4: hwmod data: do not enable or reset the McPDM during kernel init
ARM: OMAP2+: hwmod: add flag to prevent hwmod code from touching IP block during init
ARM: OMAP: hwmod: wait for sysreset complete after enabling hwmod
ARM: OMAP2+: clockdomain: Fix OMAP4 ISS clk domain to support only SWSUP
ARM: OMAP2+: PM: add missing newline to VC warning message
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Any failures in intel_sdvo_init() after the intel_sdvo_setup_output() call
left behind ghost connectors, attached (with a dangling pointer) to the
sdvo that has been cleaned up and freed. Properly destroy any connectors
attached to the encoder.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=46381
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Tested-by: bjo@nord-west.org
[danvet: added a comment to explain why we need to clean up connectors
even when sdvo_output_setup fails.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
At the same time the prcc bit for the kclk is corrected to
bit 8 instead of 3.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren <tony@atomide.com>:
This series fixes an annoying regression to make MUSB working
on omap4 again. Although it's getting rather late for these
changes for the -rc cycle, it is important as many devices
are using MUSB for charging and connectivity.
With the USB PHY changes, MUSB started using the newly added
drivers/usb/phy/omap-usb2.c driver introduced by commit
657b306a (usb: phy: add a new driver for omap usb2 phy)
that is using the newly introduced drivers/bus/omap-ocp2scp.c
introduced by commit 26a84b3e (drivers: bus: add a new driver
for omap-ocp2scp).
These changes allowed dropping a lot of PHY related code from
arch/arm/mach-omap2/omap_phy_internal.c and have it live in
the device driver like it should with commit c9e4412a (arm: omap:
phy: remove unused functions from omap-phy-internal.c).
However, MUSB on omap4 broke with these changes for legacy
platform data boot, and now only works with device tree for
omap4. Unfortunately we are still few critical bindings away
from being able to make omap4 usbale with device tree.
Fix the regression properly by adding platform data support
to the ocp2scp driver so we can avoid adding back the driver
code to arch/arm/mach-omap2.
* tag 'omap-for-v3.7-rc4/musb-regression-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: ocp2scp: create omap device for ocp2scp
ARM: OMAP4: add _dev_attr_ to ocp2scp for representing usb_phy
drivers: bus: ocp2scp: add pdata support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
When in world roaming mode, allow 40 MHz to be used
on channels 12 and 13 so that an AP that is, e.g.,
using HT40+ on channel 9 (in the UK) can be used.
Cc: stable@vger.kernel.org
Reported-by: Eddie Chapman <eddie@ehuk.net>
Tested-by: Eddie Chapman <eddie@ehuk.net>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The current topology code confuses core id vs physical package id.
In other words /sys/devices/system/cpu/cpuX/topology/core_id
displays the physical_package_id (aka socket id) instead of the
core id.
The physical_package_id sysfs attribute always displays "-1"
instead of the socket id.
Fix this mix-up with a small patch which defines and initializes
topology_physical_package_id correctly and fixes the broken
core id handling.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
If user space is running in primary mode it can switch to secondary
or access register mode, this is used e.g. in the clock_gettime code
of the vdso. If a signal is delivered to the user space process while
it has been running in access register mode the signal handler is
executed in access register mode as well which will result in a crash
most of the time.
Set the address space control bits in the PSW to the default for the
execution of the signal handler and make sure that the previous
address space control is restored on signal return. Take care
that user space can not switch to the kernel address space by
modifying the registers in the signal frame.
Cc: stable@vger.kernel.org
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
In patch "HID: microsoft: fix invalid rdesc for 3k kbd" I fixed
support for MS 3k keyboards. However the added check using memcmp and
a compound statement breaks build on architectures where memcmp is a
macro with parameters.
hid-microsoft.c:51:18: error: macro "memcmp" passed 6 arguments, but takes just 3
On x86_64, memcmp is a function, so I did not see the error.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This is another variant of iMac 9,1 with a different codec SSID.
Reported-and-tested-by: Everaldo Canuto <everaldo.canuto@gmail.com>
Cc: <stable@vger.kernel.org> [v3.3+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
It can be legitimately triggered via procfs access. Now, at least
2 of 3 of get_files_struct() callers in procfs are useless, but
when and if we get rid of those we can always add WARN_ON() here.
BUG_ON() at that spot is simply wrong.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
(1<<optname) is undefined behavior in C with a negative optname or
optname larger than 31. In those cases the result of the shift is
not necessarily zero (e.g., on x86).
This patch simplifies the code with a switch statement on optname.
It also allows the compiler to generate better code (e.g., using a
64-bit mask).
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Whoops. This was fixed previously, but not sure how it got lost. It's
not needed for -fixes or stable because at the moment
drm_i915_file_private is way bigger than i915_hw_context (by 120 bytes
on my 64b build).
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
After the rework, intel_set_mode() became a little better behaved in
restoring the current mode if we failed to apply the requested modeline.
However, the failure path for load-detect would clobber the existing
state, leading to an oops during BIOS takeover on older machines.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
With the stricter checks introduced in
commit ac911edae5960d7dccd9883f5fa5d25b591520de
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Wed Oct 31 17:50:19 2012 +0200
drm/i915: Check the framebuffer offset
(and friends), it became especially prudent to make sure that the
additional fields inside the mode were cleared before attempting to
create a framebuffer. In particular, the fb created for load detection
failed to do so and hence failed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The specs for gen2 say that the watermark values "should always be set
assuming a 32bpp display mode, even though the display mode may be 15 or
16 bpp."
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Fixes a WARN_ON in igt/tests/debugfs_reader
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
It's pretty much all consolidated now that we've killed AGP. We can move
the one outlier, and defines too.
(Kill some unused defines in the process)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This allows us to map the PTEs WC. I've not done thorough testing or
performance measurements with this patch, but it should be decent.
This is based on a patch from Jesse with the original commit message
> I've only lightly tested this so far, but the corruption seems to be
> gone if I write the GFX_FLSH_CNTL reg after binding an object. This
> register should control the TLB for the system agent, which is what CPU
> mapped objects will go through.
It has been updated for the new AGP-less code by me, and included with
it is feedback from the original patch.
v2: Updated to reflect paranoia on pte updates/register posting reads.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by [v1]: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
v2: Accidently removed an ILK case in i9xx_setup (Nicely found by Chris)
CC: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by [v1] : Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This bug existed in the old code, but was easier to fix here in the
rework. Unfortunately gen7 doesn't have a nice way to figure out the
size and we must use a lookup table.
As Jesse pointed out, there is some confusion in the docs about these
definitions. We're picking the one which seems more accurate, but we
really aren't certain.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
As a quick hack we make the old intel_gtt structure mutable so we can
fool a bunch of the existing code which depends on elements in that data
structure. We can/should try to remove this in a subsequent patch.
This should preserve the old gtt init behavior which upon writing these
patches seems incorrect. The next patch will fix these things.
The one exception is VLV which doesn't have the preserved flush control
write behavior. Since we want to do that for all GEN6+ stuff, we'll
handle that in a later patch. Mainstream VLV support doesn't actually
exist yet anyway.
v2: Update the comment to remove the "voodoo"
Check that the last pte written matches what we readback
v3: actually kill cache_level_to_agp_type since most of the flags will
disappear in an upcoming patch
v4: v3 was actually not what we wanted (Daniel)
Make the ggtt bind assertions better and stricter (Chris)
Fix some uncaught errors at gtt init (Chris)
Some other random stuff that Chris wanted
v5: check for i==0 in gen6_ggtt_bind_object to shut up gcc (Ben)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by [v4]: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Make the cache_level -> agp_flags conversion for pre-gen6 a
tad more robust by mapping everything != CACHE_NONE to the cached agp
flag - we have a 1:1 uncached mapping, but different modes of
cacheable (at least on later generations). Suggested by Chris Wilson.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This has been introduced in "drm/i915: TLB invalidation with
MI_FLUSH_DW requires a post-sync op".
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The BIOS shouldn't be touching this memory across suspend/resume, so
just leave it alone. This saves us ~6ms on resume on my T420 (retested
with write combined PTEs).
v2: change gtt restore default on pre-gen4 (Chris)
move needs_gtt_restore flag into dev_priv
v3: make sure we restore GTT on resume from hibernate (Daniel)
use opregion support as the cutoff for restore from resume (Chris)
v4: use a better check for opregion (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Kill the needs_gtt_restore indirection and check directly for
OpRegion. Also explain in a comment what's going on.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This allows the power related code to run independently of the rest of
the pipeline, extending the resume and init time improvements into
userspace, which would otherwise have been blocked on the struct mutex
if we were doing PCU communication.
v2: Also convert the locking for the rps sysfs interface.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
