| Age | Commit message (Collapse) | Author |
|---|
|
We have remove() already calling shutdown(), so let's drop it
and move the code to remove(). No code changes, we'll drop the
the FIXME in the following patch with more clean-up.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Looks like at least 2430 glue won't idle reliably with the 200 ms
autosuspend delay. This causes deeper idle states being blocked for
the whole SoC when disconnecting OTG A cable.
Increasing the delay to 500 ms seems to idle both MUSB and the PHY
reliably. This is probably because of time needed by the hardware
based negotiation between MUSB and the PHY.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the board is powering attached usb devices via the otg port
sometimes / on some devices it takes slightly too long for the Vbus
detection code in phy-sun4i-usb.c to signal that Vbus is high after
enabling Vbus and the musb hardware signals a MUSB_INTR_VBUSERROR
interrupt.
This commit sets the otg state to A_WAIT_VRISE upon enabling Vbus
making musb_stage0_irq() ignore the first VBUSERR_RETRY_COUNT
VBUSERROR interrupts, fixing connection issues in these cases.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move the mode handling to the platform_set_mode callback.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that the DMA engine check was moved to musb_tx_dma_porgram(), both
musb_tx_dma_set_mode_cppi_tusb() and musb_tx_dma_set_mode_mentor() always
return 0, so we can make both these functions *void*.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
to its caller
Commit 754fe4a92c07 ("usb: musb: Remove ifdefs for TX DMA for musb_host.c")
looks incomplete: the DMA engine checks are done outside the Mentor/UX500
handler but inside the CPPI/TUSB handler. Move the checks out of the CPPI/
TUSB handler into its caller, musb_tx_dma_program().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
urb->status is set when endpoint csr RXSTALL, H_ERROR, DATAERROR or
INCOMPRX bit is set. Those bits mean a broken pipe, so don't start next
urb when any of these bits is set by checking urb->status.
To minimize the risk of regression, only do so for RX, until we have a
test case to understand the behavior of TX.
The patch fixes system freeze issue caused by repeatedly invoking RX ISR
while removing a usb uart device connected to a hub, in which case the
hub has no chance to report the disconnect event due to the kernel is
busy in processing the RX interrupt flooding.
Fix checkpatch complaint (qh != NULL) as while.
Reported-by: Max Uvarov <muvarov@gmail.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The MUSB Programming Guide states that the driver should clear RXCSR
bit2 when the controller sets the bit.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
into drm-next
drm-intel-next-2016-05-22:
- cmd-parser support for direct reg->reg loads (Ken Graunke)
- better handle DP++ smart dongles (Ville)
- bxt guc fw loading support (Nick Hoathe)
- remove a bunch of struct typedefs from dpll code (Ander)
- tons of small work all over to avoid casting between drm_device and the i915
dev struct (Tvrtko&Chris)
- untangle request retiring from other operations, also fixes reset stat corner
cases (Chris)
- skl atomic watermark support from Matt Roper, yay!
- various wm handling bugfixes from Ville
- big pile of cdclck rework for bxt/skl (Ville)
- CABC (Content Adaptive Brigthness Control) for dsi panels (Jani&Deepak M)
- nonblocking atomic commits for plane-only updates (Maarten Lankhorst)
- bunch of PSR fixes&improvements
- untangle our map/pin/sg_iter code a bit (Dave Gordon)
drm-intel-next-2016-05-08:
- refactor stolen quirks to share code between early quirks and i915 (Joonas)
- refactor gem BO/vma funcstion (Tvrtko&Dave)
- backlight over DPCD support (Yetunde Abedisi)
- more dsi panel sequence support (Jani)
- lots of refactoring around handling iomaps, vma, ring access and related
topics culmulating in removing the duplicated request tracking in the execlist
code (Chris & Tvrtko) includes a small patch for core iomapping code
- hw state readout for bxt dsi (Ramalingam C)
- cdclk cleanups (Ville)
- dedupe chv pll code a bit (Ander)
- enable semaphores on gen8+ for legacy submission, to be able to have a direct
comparison against execlist on the same platform (Chris) Not meant to be used
for anything else but performance tuning
- lvds border bit hw state checker fix (Jani)
- rpm vs. shrinker/oom-notifier fixes (Praveen Paneri)
- l3 tuning (Imre)
- revert mst dp audio, it's totally non-functional and crash-y (Lyude)
- first official dmc for kbl (Rodrigo)
- and tons of small things all over as usual
* 'drm-intel-next' of git://anongit.freedesktop.org/drm-intel: (194 commits)
drm/i915: Revert async unpin and nonblocking atomic commit
drm/i915: Update DRIVER_DATE to 20160522
drm/i915: Inline sg_next() for the optimised SGL iterator
drm/i915: Introduce & use new lightweight SGL iterators
drm/i915: optimise i915_gem_object_map() for small objects
drm/i915: refactor i915_gem_object_pin_map()
drm/i915/psr: Implement PSR2 w/a for gen9
drm/i915/psr: Use ->get_aux_send_ctl functions
drm/i915/psr: Order DP aux transactions correctly
drm/i915/psr: Make idle_frames sensible again
drm/i915/psr: Try to program link training times correctly
drm/i915/userptr: Convert to drm_i915_private
drm/i915: Allow nonblocking update of pageflips.
drm/i915: Check for unpin correctness.
Reapply "drm/i915: Avoid stalling on pending flips for legacy cursor updates"
drm/i915: Make unpin async.
drm/i915: Prepare connectors for nonblocking checks.
drm/i915: Pass atomic states to fbc update functions.
drm/i915: Remove reset_counter from intel_crtc.
drm/i915: Remove queue_flip pointer.
...
|
|
I got one of these cards for testing uas with, it seems that with streams
it dma-s all over the place, corrupting memory. On my first tests it
managed to dma over the BIOS of the motherboard somehow and completely
bricked it.
Tests on another motherboard show that it does work with streams disabled.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that we've gotten rid of all the users of this flag we can
retire the number, leaving a slot open for a future flag user.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Several people have reported that UBSAN doesn't like the pointer
arithmetic in ehci_hub_control():
u32 __iomem *status_reg = &ehci->regs->port_status[
(wIndex & 0xff) - 1];
u32 __iomem *hostpc_reg = &ehci->regs->hostpc[(wIndex & 0xff) - 1];
If wIndex is 0 (and it often is), these calculations underflow and
UBSAN complains.
According to the C standard, pointer computations leading to locations
outside the bounds of an array object (other than 1 position past the
end) are undefined. In this case, the compiler would be justified in
concluding the wIndex can never be 0 and then optimizing away the
tests for !wIndex that occur later in the subroutine. (Although,
since ehci->regs->port_status and ehci->regs->hostpc are both 0-length
arrays and are thus GCC extensions to the C standard, it's not clear
what the compiler is really allowed to do.)
At any rate, we can avoid all these difficulties, at the cost of
making the code slightly longer, by not decrementing the index when it
is equal to 0. The runtime effect is minimal, and anyway
ehci_hub_control() is not on a hot path.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Reported-by: Meelis Roos <mroos@linux.ee>
Reported-by: Martin_MOKREJÅ <mmokrejs@gmail.com>
Reported-by: "Navin P.S" <navinp1912@gmail.com>
CC: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 198de51dbc34 ("USB: uas: Limit qdepth at the scsi-host level")
removed the scsi_change_queue_depth() call from uas_slave_configure()
assuming that the slave would inherit the host's queue_depth, which
that commit sets to the same value.
This is incorrect, without the scsi_change_queue_depth() call the slave's
queue_depth defaults to 1, introducing a performance regression.
This commit restores the call, fixing the performance regression.
Cc: stable@vger.kernel.org
Fixes: 198de51dbc34 ("USB: uas: Limit qdepth at the scsi-host level")
Reported-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 198de51dbc34 ("USB: uas: Limit qdepth at the scsi-host level") made
qdepth limit set in host template (`.can_queue = MAX_CMNDS`) redundant.
Removing it to avoid confusion.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Acer C120 LED Projector is a USB-3 connected pico projector which
takes both its power and video data from USB-3.
In combination with some hubs this device does not play well with
lpm, so disable lpm for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Properly sort all the entries by vendor id.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b1c127ae990b ("usb: host: xhci: plat: make use of new methods in
xhci_plat_priv") sets xhci->quirks before calling xhci_gen_setup(), which
will overwrite them.
Don't overwite the quirks, just add the new ones
Fixes: b1c127ae990b ("usb: host: xhci: plat: make use of new methods in xhci_plat_priv")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On some platforms, the clocks might be registered by a platform
driver. When this is the case, the clock platform driver may very well
be probed after xhci-plat, in which case the first probe() invocation
of xhci-plat will receive -EPROBE_DEFER as the return value of
devm_clk_get().
The current code handles that as a normal error, and simply assumes
that this means that the system doesn't have a clock for the XHCI
controller, and continues probing without calling
clk_prepare_enable(). Unfortunately, this doesn't work on systems
where the XHCI controller does have a clock, but that clock is
provided by another platform driver. In order to fix this situation,
we handle the -EPROBE_DEFER error condition specially, and abort the
XHCI controller probe(). It will be retried later automatically, the
clock will be available, devm_clk_get() will succeed, and the probe()
will continue with the clock prepared and enabled as expected.
In practice, such issue is seen on the ARM64 Marvell 7K/8K platform,
where the clocks are registered by a platform driver.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If commands timeout we mark them for abortion, then stop the command
ring, and turn the commands to no-ops and finally restart the command
ring.
If the host is working properly the no-op commands will finish and
pending completions are called.
If we notice the host is failing, driver clears the command ring and
completes, deletes and frees all pending commands.
There are two separate cases reported where host is believed to work
properly but is not. In the first case we successfully stop the ring
but no abort or stop command ring event is ever sent and host locks up.
The second case is if a host is removed, command times out and driver
believes the ring is stopped, and assumes it will be restarted, but
actually ends up timing out on the same command forever.
If one of the pending commands has the xhci->mutex held it will block
xhci_stop() in the remove codepath which otherwise would cleanup pending
commands.
Add a check that clears all pending commands in case host is removed,
or we are stuck timing out on the same command. Also restart the
command timeout timer when stopping the command ring to ensure we
recive an ring stop/abort event.
Cc: stable <stable@vger.kernel.org>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Under stress occasions some TI devices might not return early when
reading the status register during the quirk invocation of xhci_irq made
by usb_hcd_pci_remove. This means that instead of returning, we end up
handling this interruption in the middle of a shutdown. Since
xhci->event_ring has already been freed in xhci_mem_cleanup, we end up
accessing freed memory, causing the Oops below.
commit 8c24d6d7b09d ("usb: xhci: stop everything on the first call to
xhci_stop") is the one that changed the instant in which we clean up the
event queue when stopping a device. Before, we didn't call
xhci_mem_cleanup at the first time xhci_stop is executed (for the shared
HCD), instead, we only did it after the invocation for the primary HCD,
much later at the removal path. The code flow for this oops looks like
this:
xhci_pci_remove()
usb_remove_hcd(xhci->shared)
xhci_stop(xhci->shared)
xhci_halt()
xhci_mem_cleanup(xhci); // Free the event_queue
usb_hcd_pci_remove(primary)
xhci_irq() // Access the event_queue if STS_EINT is set. Crash.
xhci_stop()
xhci_halt()
// return early
The fix modifies xhci_stop to only cleanup the xhci data when releasing
the primary HCD. This way, we still have the event_queue configured
when invoking xhci_irq. We still halt the device on the first call to
xhci_stop, though.
I could reproduce this issue several times on the mainline kernel by
doing a bind-unbind stress test with a specific storage gadget attached.
I also ran the same test over-night with my patch applied and didn't
observe the issue anymore.
[ 113.334124] Unable to handle kernel paging request for data at address 0x00000028
[ 113.335514] Faulting instruction address: 0xd00000000d4f767c
[ 113.336839] Oops: Kernel access of bad area, sig: 11 [#1]
[ 113.338214] SMP NR_CPUS=1024 NUMA PowerNV
[c000000efe47ba90] c000000000720850 usb_hcd_irq+0x50/0x80
[c000000efe47bac0] c00000000073d328 usb_hcd_pci_remove+0x68/0x1f0
[c000000efe47bb00] d00000000daf0128 xhci_pci_remove+0x78/0xb0
[xhci_pci]
[c000000efe47bb30] c00000000055cf70 pci_device_remove+0x70/0x110
[c000000efe47bb70] c00000000061c6bc __device_release_driver+0xbc/0x190
[c000000efe47bba0] c00000000061c7d0 device_release_driver+0x40/0x70
[c000000efe47bbd0] c000000000619510 unbind_store+0x120/0x150
[c000000efe47bc20] c0000000006183c4 drv_attr_store+0x64/0xa0
[c000000efe47bc60] c00000000039f1d0 sysfs_kf_write+0x80/0xb0
[c000000efe47bca0] c00000000039e14c kernfs_fop_write+0x18c/0x1f0
[c000000efe47bcf0] c0000000002e962c __vfs_write+0x6c/0x190
[c000000efe47bd90] c0000000002eab40 vfs_write+0xc0/0x200
[c000000efe47bde0] c0000000002ec85c SyS_write+0x6c/0x110
[c000000efe47be30] c000000000009260 system_call+0x38/0x108
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: joel@jms.id.au
Cc: stable@vger.kernel.org
Reviewed-by: Roger Quadros <rogerq@ti.com>
Cc: <stable@vger.kernel.org> #v4.3+
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This flag is a no-op now (see commit 47b0eeb3dc8a "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Cc: Purna Chandra Mandal <purna.mandal@microchip.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: <linux-mips@linux-mips.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
This flag is a no-op now (see commit 47b0eeb3dc8a "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Cc: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
Frist -misc pull for 4.8, with pretty much just random all over plus a few
more lockless gem BO patches acked/reviewed by driver maintainers.
I'm starting a bit earlier this time around because there's a few invasive
patch series to land (nonblocking atomic prep work, fence prep work,
rst/sphinx kerneldoc finally happening) and I need a baseline with all the
branches merged.
* tag 'topic/drm-misc-2016-06-01' of git://anongit.freedesktop.org/drm-intel: (21 commits)
drm/vc4: Use lockless gem BO free callback
drm/vc4: Use drm_gem_object_unreference_unlocked
drm: Initialize a linear gamma table by default
drm/vgem: Use lockless gem BO free callback
drm/qxl: Don't set a gamma table size
drm/msm: Nuke dummy gamma_set/get functions
drm/cirrus: Drop redundnant gamma size check
drm/fb-helper: Remove dead code in setcolreg
drm/mediatek: Use lockless gem BO free callback
drm/hisilicon: Use lockless gem BO free callback
drm/hlcd: Use lockless gem BO free callback
vga_switcheroo: Support deferred probing of audio clients
vga_switcheroo: Add helper for deferred probing
virtio-gpu: fix output lookup
drm/doc: Unify KMS Locking docs
drm/atomic-helper: Do not call ->mode_fixup for CRTC which will be disabled
Fix annoyingly awkward typo in drm_edid_load.c
drm/doc: Drop vblank_disable_allow wording
drm: use seqlock for vblank time/count
drm/mm: avoid possible null pointer dereference
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
Here's the first set of fixes for v4.7-rc
cycle. Nothing extra fancy this time around.
Patches range from MS OS Descriptor usage fixes, to
Clear Stall EP command fix on dwc3, to some f_fs
fixes and out of bounds accesses on renesas driver.
|
|
This flag is a no-op now (see commit 47b0eeb3dc8a "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
git://git.pengutronix.de/git/pza/linux into drm-fixes
mediatek-drm fixes
- remove an invalid, unreachable error message and NULL pointer dereference
- remove a spurious drm_connector_unregister call from the DSI driver
* tag 'mediatek-drm-fixes-2016-06-01' of git://git.pengutronix.de/git/pza/linux:
drm/mediatek: mtk_dsi: Remove spurious drm_connector_unregister
drm/mediatek: mtk_dpi: remove invalid error message
|
|
The address check in acpi_hw_get_access_bit_width() should be byte width
based, not bit width based. This patch fixes this mistake.
For those who want to review acpi_hw_access_bit_width(), here is the
concerns and the design details of the function:
It is supposed that the GAS Address field should be aligned to the byte
width indicated by the GAS AccessSize field. Similarly, for the old non
GAS register, it is supposed that its Address should be aligned to its
Length.
For the "AccessSize = 0 (meaning ANY)" case, we try to return the maximum
instruction width (64 for MMIO or 32 for PIO) or the user expected access
bit width (64 for acpi_read()/acpi_write() or 32 for acpi_hw_read()/
acpi_hw_write()) and it is supposed that the GAS Address field should
always be aligned to the maximum expected access bit width (otherwise it
can't be accessed using ANY access bit width).
The problem is in acpi_tb_init_generic_address(), where the non GAS
register's Length is converted into the GAS BitWidth field, its Address is
converted into the GAS Address field, and the GAS AccessSize field is left
0 but most of the registers actually cannot be accessed using "ANY"
accesses.
As a conclusion, when AccessSize = 0 (ANY), the Address should either be
aligned to the BitWidth (wrong conversion) or aligned to 32 for PIO or 64
for MMIO (real GAS). Since currently, max_bit_width is 32, then:
1. BitWidth for the wrong conversion is 8,16,32; and
2. The Address of the real GAS should always be aligned to 8,16,32.
The address alignment check to exclude false matched real GAS is not
necessary. Thus this patch fixes the issue by removing the address
alignment check.
On the other hand, we in fact could use a simpler check of
"reg->bit_width < max_bit_width" to exclude the "BitWidth=64 PIO" case that
may be issued from acpi_read()/acpi_write() in the future.
Fixes: b314a172ee96 (ACPICA: Hardware: Add optimized access bit width support)
Reported-and-tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Acked-by: Mike Marshall <hubcap@omnibond.com>
Suggested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The return value of clamp_val() has to be stored actually.
Fixes: b7898fda5bc7 (cpufreq: Support for fast frequency switching)
Reported-by: Steve Muckle <steve.muckle@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here are three pin control fixes for v4.7. Not much, and just driver
fixes:
- add device tree matches to MAINTAINERS
- inversion bug in the Nomadik driver
- dual edge handling bug in the mediatek driver"
* tag 'pinctrl-v4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: mediatek: fix dual-edge code defect
MAINTAINERS: Add file patterns for pinctrl device tree bindings
pinctrl: nomadik: fix inversion of gpio direction
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sumits/dma-buf
Pull dma-buf updates from Sumit Semwal:
- use of vma_pages instead of explicit computation
- DocBook and headerdoc updates for dma-buf
* tag 'dma-buf-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/sumits/dma-buf:
dma-buf: use vma_pages()
fence: add missing descriptions for fence
doc: update/fixup dma-buf related DocBook
reservation: add headerdoc comments
dma-buf: headerdoc fixes
|
|
In commit 86d3473224b0 some of the checking for a valid timeval
was subtley changed which caused -EINVAL to be returned whenever
the timeval was null.
However, it is possible to set the timezone data while specifying
a NULL timeval, which is usually done to handle systems where the
RTC keeps local time instead of UTC. Thus the patch causes such
systems to have the time incorrectly set.
This patch addresses the issue by handling the error conditionals
in the same way as was done previously.
Fixes: 86d3473224b0 "time: Introduce do_sys_settimeofday64()"
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Baolin Wang <baolin.wang@linaro.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Link: http://lkml.kernel.org/r/1464807207-16530-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
We're missing entries for mlock2, copy_file_range, preadv2 and pwritev2
in our compat syscall table, so hook them up. Only the last two need
compat wrappers.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
if downscaling is enabled plane data rate increases according to scaling
amount. take scaling amount under consideration while calculating plane
data rate
v2: Address Matt's comments, where data rate was overridden because of
missing else.
v3 (by Matt):
- Add braces to 'else' branch to match kernel coding style
- Adjust final calculation now that skl_plane_downscale_amount()
returns 16.16 fixed point value instead of a decimal fixed point
v4 (by Matt):
- Avoid integer overflow by making sure final multiplication is
treated as 64-bit.
Cc: matthew.d.roper@intel.com
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463695381-21368-1-git-send-email-matthew.d.roper@intel.com
|
|
Don't use pipe pixel rate for plane pixel rate. Calculate plane pixel according
to formula
adjusted plane_pixel_rate = adjusted pipe_pixel_rate * downscale ammount
downscale amount = max[1, src_h/dst_h] * max[1, src_w/dst_w]
if 90/270 rotation use rotated width & height
v2: use intel_plane_state->visible instead of (fb == NULL) as per Matt's
comment.
v3 (by Matt):
- Keep downscale amount in 16.16 fixed point rather than converting to
decimal fixed point.
- Store adjusted plane pixel rate in plane state instead of the plane
parameters structure that we no longer use.
v4 (by Matt):
- Significant rebasing onto latest atomic watermark work
- Don't bother storing plane pixel rate in state; just calculate it
right before the calls that make use of it.
- Fix downscale calculations to actually use width values when
computing downscale_w rather than copy/pasted height values.
Cc: matthew.d.roper@intel.com
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463439121-28974-4-git-send-email-matthew.d.roper@intel.com
|
|
don't always use 8 ddb as minimum, instead calculate using proper
algorithm.
v2: optimizations as per Matt's comments.
v3 (by Matt):
- Fix boolean logic for !fb test in skl_ddb_min_alloc()
- Adjust negative tiling format comparisons in skl_ddb_min_alloc() to
improve readability.
v4 (by Matt):
- Rebase onto recent atomic watermark changes
- Slight tweaks to code flow to make the logic more closely match the
description in the bspec.
v5 (by Matt):
- Handle minimum scanline calculation properly for 4 & 8 bpp formats.
8bpp isn't actually possible right now, but it's listed in the bspec
so I've included it here for forward compatibility (similar to how
we have logic for NV12).
v6 (by Matt):
- Calculate plane_bpp correctly for non-NV12 formats. (Mahesh)
Cc: matthew.d.roper@intel.com
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464713939-10440-1-git-send-email-matthew.d.roper@intel.com
|
|
We don't actually read out full plane state during driver startup (only
whether the primary plane is enabled/disabled), so all of the src/dest
rectangles are invalid at this point. However this calculation was
needless anyway since we re-calculate them from scratch on the very
first atomic transaction after boot anyway.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463439121-28974-2-git-send-email-matthew.d.roper@intel.com
|
|
Fixes commit 60f9ce3ada53
("thermal: of-thermal: allow setting trip_temp on hardware")
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
The freq_table array is not populated before calling
thermal_of_cooling_register. The code which populates the freq table was
introduced in commit f6859014.
This should be done before registering new thermal cooling device.
The log shows effects of this wrong decision.
[ 2.172614] cpu cpu1: Failed to get voltage for frequency 1984518656000: -34
[ 2.220863] cpu cpu0: Failed to get voltage for frequency 1984524416000: -34
Cc: <stable@vger.kernel.org> # 3.19+
Fixes: f6859014c7e7 ("thermal: cpu_cooling: Store frequencies in descending order")
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Javi Merino <javi.merino@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Connectors are unregistered by mtk_drm_drv via drm_connector_unregister_all().
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Do not try to dereference dpi if it is NULL.
Since dpi can never be NULL when mtk_dpi_set_display_mode() is called,
remove the message.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The firmware found in the touch screen of an SP3 is buggy and may miss
to send lift off reports for contacts. Try to work around that issue by
using MT_QUIRK_NOT_SEEN_MEANS_UP.
based on a patch from: Daniel Martin <consume.noise@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
If kmalloc() returned NULL we would end up dereferencing "state" a
couple lines later.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Reset crtc->state to NULL after freeing the state object and call
__drm_atomic_helper_crtc_destroy_state() helper instead of manually
calling drm_property_unreference_blob().
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Flushing a work that reschedules itself is not a sensible operation. It needs
to be killed. Failure to do so leads to a kernel panic in the timer code.
CC: stable@vger.kernel.org
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
With this error output becomes almost readable. The line numbers are
still totally bonghits, but that's a lot harder to pull out of
kerneldoc. We'd essentially have to insert some special markers in the
kernel-doc output, split the output along these markers and then
insert each block separately using
state_machine.insert_input(block, source, first_line)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: linux-doc@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
If the VBT says that a certain port should be eDP (and hence fused off
from HDMI), but in reality it isn't, we need to try and acquire the HDMI
connection instead. So only trust the VBT edp setting if we can connect
to an eDP device on that port.
Fixes: d2182a6608 (drm/i915: Don't register HDMI connectors for eDP ports on VLV/CHV)
References: https://bugs.freedesktop.org/show_bug.cgi?id=96288
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Phidias Chiang <phidias.chiang@canonical.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464766070-31623-1-git-send-email-chris@chris-wilson.co.uk
|
|
Signed-off-by: Yan, Zheng <zyan@redhat.com>
|
|
There are several issues in fscache revalidation code.
- In ceph_revalidate_work(), fscache_invalidate() is called when
fscache_check_consistency() return 0. This is complete wrong
because 0 means cache is valid.
- Handle_cap_grant() calls ceph_queue_revalidate() if client
already has CAP_FILE_CACHE. This code is confusing. Client
should revalidate the cache each time it got CAP_FILE_CACHE
anew.
- In Handle_cap_grant(), fscache_invalidate() is called if MDS
revokes CAP_FILE_CACHE. This is inconsistency with the case
that inode get evicted. In the later case, the cache is not
discarded. Client may use the cache when inode is reloaded.
This patch moves the fscache revalidation into ceph_get_caps().
Client revalidates the cache after it gets CAP_FILE_CACHE.
i_rdcache_gen should keep constance while CAP_FILE_CACHE is
used. If i_fscache_gen is not equal to i_rdcache_gen, client
needs to check cache's consistency.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
|
|
All other filesystems do not add dirty pages to fscache. They all
disable fscache when inode is opened for write. Only ceph adds
dirty pages to fscache, but the code is buggy.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
|
|
ceph_fill_file_size() has already called ceph_fscache_invalidate()
if it return true.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
|
