summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-09-01ARC: [plat-hsdk]: Switch ethernet phy-mode to rgmii-idEvgeniy Didin
HSDK board has Micrel KSZ9031, recent commit bcf3440c6dd ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY") caused a breakdown of Ethernet. Using 'phy-mode = "rgmii"' is not correct because accodring RGMII specification it is necessary to have delay on RX (PHY to MAX) which is not generated in case of "rgmii". Using "rgmii-id" adds necessary delay and solves the issue. Also adding name of PHY placed on HSDK board. Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com> Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Cc: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
2020-09-01pktgen: fix error message with wrong function nameLeesoo Ahn
Error on calling kthread_create_on_node prints wrong function name, kernel_thread. Fixes: 94dcf29a11b3 ("kthread: use kthread_create_on_node()") Signed-off-by: Leesoo Ahn <dev@ooseel.net> Acked-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-01arc: fix memory initialization for systems with two memory banksMike Rapoport
Rework of memory map initialization broke initialization of ARC systems with two memory banks. Before these changes, memblock was not aware of nodes configuration and the memory map was always allocated from the "lowmem" bank. After the addition of node information to memblock, the core mm attempts to allocate the memory map for the "highmem" bank from its node. The access to this memory using __va() fails because it can be only accessed using kmap. Anther problem that was uncovered is that {min,max}_high_pfn are calculated from u64 high_mem_start variable which prevents truncation to 32-bit physical address and the PFN values are above the node and zone boundaries. Use phys_addr_t type for high_mem_start and high_mem_size to ensure correspondence between PFNs and highmem zone boundaries and reserve the entire highmem bank until mem_init() to avoid accesses to it before highmem is enabled. To test this: 1. Enable HIGHMEM in ARC config 2. Enable 2 memory banks in haps_hs.dts (uncomment the 2nd bank) Fixes: 51930df5801e ("mm: free_area_init: allow defining max_zone_pfn in descending order") Cc: stable@vger.kernel.org [5.8] Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com> [vgupta: added instructions to test highmem]
2020-09-01Merge branch 'opp/fixes' of ↵Rafael J. Wysocki
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm Pull operating performance points (OPP) framework fixes for 5.9-rc4 from Viresh Kumar: "This fixes reference counting for OPP tables. Few patches are getting queued (for various subsystems) for 5.10 which depend on this to be fixed first." * 'opp/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm: opp: Don't drop reference for an OPP table that was never parsed
2020-09-01ia64: fix min_low_pfn/max_low_pfn build errorsRandy Dunlap
Fix min_low_pfn/max_low_pfn build errors for arch/ia64/: (e.g.) ERROR: "max_low_pfn" [drivers/rpmsg/virtio_rpmsg_bus.ko] undefined! ERROR: "min_low_pfn" [drivers/rpmsg/virtio_rpmsg_bus.ko] undefined! ERROR: "min_low_pfn" [drivers/hwtracing/intel_th/intel_th_msu.ko] undefined! ERROR: "max_low_pfn" [drivers/hwtracing/intel_th/intel_th_msu.ko] undefined! ERROR: "min_low_pfn" [drivers/crypto/cavium/nitrox/n5pf.ko] undefined! ERROR: "max_low_pfn" [drivers/crypto/cavium/nitrox/n5pf.ko] undefined! ERROR: "max_low_pfn" [drivers/md/dm-integrity.ko] undefined! ERROR: "min_low_pfn" [drivers/md/dm-integrity.ko] undefined! ERROR: "max_low_pfn" [crypto/tcrypt.ko] undefined! ERROR: "min_low_pfn" [crypto/tcrypt.ko] undefined! ERROR: "min_low_pfn" [security/keys/encrypted-keys/encrypted-keys.ko] undefined! ERROR: "max_low_pfn" [security/keys/encrypted-keys/encrypted-keys.ko] undefined! ERROR: "min_low_pfn" [arch/ia64/kernel/mca_recovery.ko] undefined! ERROR: "max_low_pfn" [arch/ia64/kernel/mca_recovery.ko] undefined! David suggested just exporting min_low_pfn & max_low_pfn in mm/memblock.c: https://lore.kernel.org/lkml/alpine.DEB.2.22.394.2006291911220.1118534@chino.kir.corp.google.com/ Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: David Rientjes <rientjes@google.com> Acked-by: Tony Luck <tony.luck@intel.com> Cc: linux-mm@kvack.org Cc: Andrew Morton <akpm@linux-foundation.org> Cc: David Rientjes <rientjes@google.com> Cc: Mike Rapoport <rppt@linux.ibm.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: linux-ia64@vger.kernel.org Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
2020-09-01perf report: Disable ordered_events for raw dumpJiri Olsa
Disable ordered_events for report raw dump, because for raw dump we want to see events as they are stored in the perf.data file, not sorted by time. Signed-off-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20200827134830.126721-1-jolsa@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2020-09-01perf tools: Correct SNOOPX field offsetAl Grant
perf_event.h has macros that define the field offsets in the data_src bitmask in perf records. The SNOOPX and REMOTE offsets were both 37. These are distinct fields, and the bitfield layout in perf_mem_data_src confirms that SNOOPX should be at offset 38. Committer notes: This was extracted from a larger patch that also contained kernel changes. Fixes: 52839e653b5629bd ("perf tools: Add support for printing new mem_info encodings") Signed-off-by: Al Grant <al.grant@arm.com> Reviewed-by: Andi Kleen <ak@linux.intel.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/9974f2d0-bf7f-518e-d9f7-4520e5ff1bb0@foss.arm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2020-09-01perf intel-pt: Fix corrupt data after perf inject fromAl Grant
Commit 42bbabed09ce6208 ("perf tools: Add hw_idx in struct branch_stack") changed the format of branch stacks in perf samples. When samples use this new format, a flag must be set in the corresponding event. Synthesized branch stacks generated from Intel PT were using the new format, but not setting the event attribute, leading to consumers seeing corrupt data. This patch fixes the issue by setting the event attribute to indicate use of the new format. Fixes: 42bbabed09ce6208 ("perf tools: Add hw_idx in struct branch_stack") Signed-off-by: Al Grant <al.grant@arm.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Leo Yan <leo.yan@linaro.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mike Leach <mike.leach@linaro.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Suzuki Poulouse <suzuki.poulose@arm.com> Cc: linux-arm-kernel@lists.infradead.org Link: http://lore.kernel.org/lkml/20200819084751.17686-2-leo.yan@linaro.org Signed-off-by: Leo Yan <leo.yan@linaro.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2020-09-01perf cs-etm: Fix corrupt data after perf inject fromAl Grant
Commit 42bbabed09ce6208 ("perf tools: Add hw_idx in struct branch_stack") changed the format of branch stacks in perf samples. When samples use this new format, a flag must be set in the corresponding event. Synthesized branch stacks generated from CoreSight ETM trace were using the new format, but not setting the event attribute, leading to consumers seeing corrupt data. This patch fixes the issue by setting the event attribute to indicate use of the new format. Fixes: 42bbabed09ce6208 ("perf tools: Add hw_idx in struct branch_stack") Signed-off-by: Al Grant <al.grant@arm.com> Reviewed-by: Andrea Brunato <andrea.brunato@arm.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Mike Leach <mike.leach@linaro.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Suzuki Poulouse <suzuki.poulose@arm.com> Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Leo Yan <leo.yan@linaro.org> Link: http://lore.kernel.org/lkml/20200819084751.17686-1-leo.yan@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2020-09-01perf top/report: Fix infinite loop in the TUI for grouped eventsArnaldo Carvalho de Melo
For a while we need to have a dummy event for doing things like receiving PERF_RECORD_COMM, PERF_RECORD_EXEC, etc for threads being created and dying while we synthesize the pre-existing ones at tool start. This 'dummy' event is needed for keeping track of thread lifetime events early in the session but are uninteresting otherwise, i.e. no need to have it in a initial events menu for the non-grouped case, i.e. for: # perf top -e cycles,instructions or even for plain: # perf top When 'cycles' and that 'dummy' event are in place. The code to remove that 'dummy' event ended up creating an endless loop for the grouped case, i.e.: # perf top -e '{cycles,instructions}' Fix it. Fixes: bee9ca1c8a237ca1 ("perf report TUI: Remove needless 'dummy' event from menu") Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2020-09-01perf parse-events: Avoid an uninitialized read when using fake PMUsIan Rogers
With a fake_pmu the pmu_info isn't populated by perf_pmu__check_alias. In this case, don't try to copy the uninitialized values to the evsel. Signed-off-by: Ian Rogers <irogers@google.com> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Kajol Jain <kjain@linux.ibm.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Leo Yan <leo.yan@linaro.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Link: http://lore.kernel.org/lkml/20200826042910.1902374-2-irogers@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2020-09-01perf stat: Fix out of bounds array access in the print_counters() evlist methodThomas Richter
Fix a compile error on F32 and gcc version 10.1 on s390 in file utils/stat-display.c. The error does not show up with make DEBUG=y. In fact the issue shows up when using both compiler options -O6 and -D_FORTIFY_SOURCE=2 (which are omitted with DEBUG=Y). This is the offending call chain: print_counter_aggr() printout(config, -1, 0, ...) with 2nd parm id set to -1 aggr_printout(config, x, id --> -1, ...) which leads to this code: case AGGR_NONE: if (evsel->percore && !config->percore_show_thread) { .... } else { fprintf(config->output, "CPU%*d%s", config->csv_output ? 0 : -7, evsel__cpus(evsel)->map[id], ^^ id is -1 !!!! config->csv_sep); } This is a compiler inlining issue which is detected on s390 but not on other plattforms. Output before: # make util/stat-display.o ..... util/stat-display.c: In function ‘perf_evlist__print_counters’: util/stat-display.c:121:4: error: array subscript -1 is below array bounds of ‘int[]’ [-Werror=array-bounds] 121 | fprintf(config->output, "CPU%*d%s", | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 122 | config->csv_output ? 0 : -7, | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 123 | evsel__cpus(evsel)->map[id], | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 124 | config->csv_sep); | ~~~~~~~~~~~~~~~~ In file included from util/evsel.h:13, from util/evlist.h:13, from util/stat-display.c:9: /root/linux/tools/lib/perf/include/internal/cpumap.h:10:7: note: while referencing ‘map’ 10 | int map[]; | ^~~ cc1: all warnings being treated as errors mv: cannot stat 'util/.stat-display.o.tmp': No such file or directory make[3]: *** [/root/linux/tools/build/Makefile.build:97: util/stat-display.o] Error 1 make[2]: *** [Makefile.perf:716: util/stat-display.o] Error 2 make[1]: *** [Makefile.perf:231: sub-make] Error 2 make: *** [Makefile:110: util/stat-display.o] Error 2 [root@t35lp46 perf]# Output after: # make util/stat-display.o ..... CC util/stat-display.o [root@t35lp46 perf]# Committer notes: Removed the removal of {} enclosing the multiline else block, as pointed out by Jiri Olsa. Suggested-by: Jiri Olsa <jolsa@redhat.com> Signed-off-by: Thomas Richter <tmricht@linux.ibm.com> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Sumanth Korikkar <sumanthk@linux.ibm.com> Cc: Sven Schnelle <svens@linux.ibm.com> Cc: Vasily Gorbik <gor@linux.ibm.com> Link: http://lore.kernel.org/lkml/20200825063304.77733-1-tmricht@linux.ibm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2020-09-01perf test: Set NULL sentinel in pmu_events table in "Parse and process ↵Thomas Richter
metrics" test Linux 5.9 introduced perf test case "Parse and process metrics" and on s390 this test case always dumps core: [root@t35lp67 perf]# ./perf test -vvvv -F 67 67: Parse and process metrics : --- start --- metric expr inst_retired.any / cpu_clk_unhalted.thread for IPC parsing metric: inst_retired.any / cpu_clk_unhalted.thread Segmentation fault (core dumped) [root@t35lp67 perf]# I debugged this core dump and gdb shows this call chain: (gdb) where #0 0x000003ffabc3192a in __strnlen_c_1 () from /lib64/libc.so.6 #1 0x000003ffabc293de in strcasestr () from /lib64/libc.so.6 #2 0x0000000001102ba2 in match_metric(list=0x1e6ea20 "inst_retired.any", n=<optimized out>) at util/metricgroup.c:368 #3 find_metric (map=<optimized out>, map=<optimized out>, metric=0x1e6ea20 "inst_retired.any") at util/metricgroup.c:765 #4 __resolve_metric (ids=0x0, map=<optimized out>, metric_list=0x0, metric_no_group=<optimized out>, m=<optimized out>) at util/metricgroup.c:844 #5 resolve_metric (ids=0x0, map=0x0, metric_list=0x0, metric_no_group=<optimized out>) at util/metricgroup.c:881 #6 metricgroup__add_metric (metric=<optimized out>, metric_no_group=metric_no_group@entry=false, events=<optimized out>, events@entry=0x3ffd84fb878, metric_list=0x0, metric_list@entry=0x3ffd84fb868, map=0x0) at util/metricgroup.c:943 #7 0x00000000011034ae in metricgroup__add_metric_list (map=0x13f9828 <map>, metric_list=0x3ffd84fb868, events=0x3ffd84fb878, metric_no_group=<optimized out>, list=<optimized out>) at util/metricgroup.c:988 #8 parse_groups (perf_evlist=perf_evlist@entry=0x1e70260, str=str@entry=0x12f34b2 "IPC", metric_no_group=<optimized out>, metric_no_merge=<optimized out>, fake_pmu=fake_pmu@entry=0x1462f18 <perf_pmu.fake>, metric_events=0x3ffd84fba58, map=0x1) at util/metricgroup.c:1040 #9 0x0000000001103eb2 in metricgroup__parse_groups_test( evlist=evlist@entry=0x1e70260, map=map@entry=0x13f9828 <map>, str=str@entry=0x12f34b2 "IPC", metric_no_group=metric_no_group@entry=false, metric_no_merge=metric_no_merge@entry=false, metric_events=0x3ffd84fba58) at util/metricgroup.c:1082 #10 0x00000000010c84d8 in __compute_metric (ratio2=0x0, name2=0x0, ratio1=<synthetic pointer>, name1=0x12f34b2 "IPC", vals=0x3ffd84fbad8, name=0x12f34b2 "IPC") at tests/parse-metric.c:159 #11 compute_metric (ratio=<synthetic pointer>, vals=0x3ffd84fbad8, name=0x12f34b2 "IPC") at tests/parse-metric.c:189 #12 test_ipc () at tests/parse-metric.c:208 ..... ..... omitted many more lines This test case was added with commit 218ca91df477 ("perf tests: Add parse metric test for frontend metric"). When I compile with make DEBUG=y it works fine and I do not get a core dump. It turned out that the above listed function call chain worked on a struct pmu_event array which requires a trailing element with zeroes which was missing. The marco map_for_each_event() loops over that array tests for members metric_expr/metric_name/metric_group being non-NULL. Adding this element fixes the issue. Output after: [root@t35lp46 perf]# ./perf test 67 67: Parse and process metrics : Ok [root@t35lp46 perf]# Committer notes: As Ian remarks, this is not s390 specific: <quote Ian> This also shows up with address sanitizer on all architectures (perhaps change the patch title) and perhaps add a "Fixes: <commit>" tag. ================================================================= ==4718==ERROR: AddressSanitizer: global-buffer-overflow on address 0x55c93b4d59e8 at pc 0x55c93a1541e2 bp 0x7ffd24327c60 sp 0x7ffd24327c58 READ of size 8 at 0x55c93b4d59e8 thread T0 #0 0x55c93a1541e1 in find_metric tools/perf/util/metricgroup.c:764:2 #1 0x55c93a153e6c in __resolve_metric tools/perf/util/metricgroup.c:844:9 #2 0x55c93a152f18 in resolve_metric tools/perf/util/metricgroup.c:881:9 #3 0x55c93a1528db in metricgroup__add_metric tools/perf/util/metricgroup.c:943:9 #4 0x55c93a151996 in metricgroup__add_metric_list tools/perf/util/metricgroup.c:988:9 #5 0x55c93a1511b9 in parse_groups tools/perf/util/metricgroup.c:1040:8 #6 0x55c93a1513e1 in metricgroup__parse_groups_test tools/perf/util/metricgroup.c:1082:9 #7 0x55c93a0108ae in __compute_metric tools/perf/tests/parse-metric.c:159:8 #8 0x55c93a010744 in compute_metric tools/perf/tests/parse-metric.c:189:9 #9 0x55c93a00f5ee in test_ipc tools/perf/tests/parse-metric.c:208:2 #10 0x55c93a00f1e8 in test__parse_metric tools/perf/tests/parse-metric.c:345:2 #11 0x55c939fd7202 in run_test tools/perf/tests/builtin-test.c:410:9 #12 0x55c939fd6736 in test_and_print tools/perf/tests/builtin-test.c:440:9 #13 0x55c939fd58c3 in __cmd_test tools/perf/tests/builtin-test.c:661:4 #14 0x55c939fd4e02 in cmd_test tools/perf/tests/builtin-test.c:807:9 #15 0x55c939e4763d in run_builtin tools/perf/perf.c:313:11 #16 0x55c939e46475 in handle_internal_command tools/perf/perf.c:365:8 #17 0x55c939e4737e in run_argv tools/perf/perf.c:409:2 #18 0x55c939e45f7e in main tools/perf/perf.c:539:3 0x55c93b4d59e8 is located 0 bytes to the right of global variable 'pme_test' defined in 'tools/perf/tests/parse-metric.c:17:25' (0x55c93b4d54a0) of size 1352 SUMMARY: AddressSanitizer: global-buffer-overflow tools/perf/util/metricgroup.c:764:2 in find_metric Shadow bytes around the buggy address: 0x0ab9a7692ae0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0ab9a7692af0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0ab9a7692b00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0ab9a7692b10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0ab9a7692b20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 =>0x0ab9a7692b30: 00 00 00 00 00 00 00 00 00 00 00 00 00[f9]f9 f9 0x0ab9a7692b40: f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 0x0ab9a7692b50: f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 0x0ab9a7692b60: f9 f9 f9 f9 f9 f9 f9 f9 00 00 00 00 00 00 00 00 0x0ab9a7692b70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0ab9a7692b80: f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 f9 Shadow byte legend (one shadow byte represents 8 application bytes): Addressable: 00 Partially addressable: 01 02 03 04 05 06 07 Heap left redzone: fa Freed heap region: fd Stack left redzone: f1 Stack mid redzone: f2 Stack right redzone: f3 Stack after return: f5 Stack use after scope: f8 Global redzone: f9 Global init order: f6 Poisoned by user: f7 Container overflow: fc Array cookie: ac Intra object redzone: bb ASan internal: fe Left alloca redzone: ca Right alloca redzone: cb Shadow gap: cc </quote> I'm also adding the missing "Fixes" tag and setting just .name to NULL, as doing it that way is more compact (the compiler will zero out everything else) and the table iterators look for .name being NULL as the sentinel marking the end of the table. Fixes: 0a507af9c681ac2a ("perf tests: Add parse metric test for ipc metric") Signed-off-by: Thomas Richter <tmricht@linux.ibm.com> Reviewed-by: Sumanth Korikkar <sumanthk@linux.ibm.com> Acked-by: Ian Rogers <irogers@google.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Sven Schnelle <svens@linux.ibm.com> Cc: Vasily Gorbik <gor@linux.ibm.com> Link: http://lore.kernel.org/lkml/20200825071211.16959-1-tmricht@linux.ibm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2020-09-01perf parse-events: Set exclude_guest=1 for user-space countingJin Yao
Currently if we run 'perf record -e cycles:u', exclude_guest=0. But it doesn't make sense in most cases that we request for user-space counting but we also get the guest report. Of course, we also need to consider 'perf kvm' usage case that authorized perf users on the host may only want to count guest user space events. For example, # perf kvm --guest record -e cycles:u When we have 'exclude_guest=1' for 'perf kvm' usage, we may get nothing from guest events. To keep perf semantics consistent and clear, this patch sets exclude_guest=1 for user-space counting but except for 'perf kvm' usage. Before: perf record -e cycles:u ./div perf evlist -v cycles:u: ..., exclude_kernel: 1, exclude_hv: 1, ... After: perf record -e cycles:u ./div perf evlist -v cycles:u: ..., exclude_kernel: 1, exclude_hv: 1, exclude_guest: 1, ... Before: perf kvm --guest record -e cycles:u -vvv perf_event_attr: size 120 { sample_period, sample_freq } 4000 sample_type IP|TID|TIME|ID|CPU|PERIOD read_format ID disabled 1 inherit 1 exclude_kernel 1 exclude_hv 1 freq 1 sample_id_all 1 After: perf kvm --guest record -e cycles:u -vvv perf_event_attr: size 120 { sample_period, sample_freq } 4000 sample_type IP|TID|TIME|ID|CPU|PERIOD read_format ID disabled 1 inherit 1 exclude_kernel 1 exclude_hv 1 freq 1 sample_id_all 1 For Before/After, exclude_guest are both 0 for perf kvm usage. perf test 6 6: Parse event definition strings : Ok Signed-off-by: Jin Yao <yao.jin@linux.intel.com> Tested-by: Like Xu <like.xu@linux.intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jin Yao <yao.jin@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20200814012120.16647-1-yao.jin@linux.intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2020-09-01perf record: Correct the help info of option "--no-bpf-event"Wei Li
The help info of option "--no-bpf-event" is wrongly described as "record bpf events", correct it. Committer testing: $ perf record -h bpf Usage: perf record [<options>] [<command>] or: perf record [<options>] -- <command> [<options>] --clang-opt <clang options> options passed to clang when compiling BPF scriptlets --clang-path <clang path> clang binary to use for compiling BPF scriptlets --no-bpf-event do not record bpf events $ Fixes: 71184c6ab7e6 ("perf record: Replace option --bpf-event with --no-bpf-event") Signed-off-by: Wei Li <liwei391@huawei.com> Acked-by: Song Liu <songliubraving@fb.com> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Hanjun Guo <guohanjun@huawei.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Li Bin <huawei.libin@huawei.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Link: http://lore.kernel.org/lkml/20200819031947.12115-1-liwei391@huawei.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2020-09-01perf tools: Use %zd for size_t printf formats on 32-bitChris Wilson
A couple of trivial fixes for using %zd for size_t in the code supporting the ZSTD compression library. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexey Budankov <alexey.budankov@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20200820212501.24421-1-chris@chris-wilson.co.uk Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2020-09-01block: fix locking in bdev_del_partitionChristoph Hellwig
We need to hold the whole device bd_mutex to protect against other thread concurrently deleting out partition before we get to it, and thus causing a use after free. Fixes: cddae808aeb7 ("block: pass a hd_struct to delete_partition") Reported-by: syzbot+6448f3c229bc52b82f69@syzkaller.appspotmail.com Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-09-01block: release disk reference in hd_struct_free_workMing Lei
Commit e8c7d14ac6c3 ("block: revert back to synchronous request_queue removal") stops to release request queue from wq context because that commit supposed all blk_put_queue() is called in context which is allowed to sleep. However, this assumption isn't true because we release disk's reference in partition's percpu_ref's ->release() which doesn't allow to sleep, because the ->release() is run via call_rcu(). Fixes this issue by moving put disk reference into hd_struct_free_work() Fixes: e8c7d14ac6c3 ("block: revert back to synchronous request_queue removal") Reported-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Tested-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-09-01io_uring: fix removing the wrong file in __io_sqe_files_update()Jiufei Xue
Index here is already the position of the file in fixed_file_table, we should not use io_file_from_index() again to get it. Otherwise, the wrong file which still in use may be released unexpectedly. Cc: stable@vger.kernel.org # v5.6 Fixes: 05f3fb3c5397 ("io_uring: avoid ring quiesce for fixed file set unregister and update") Signed-off-by: Jiufei Xue <jiufei.xue@linux.alibaba.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-09-01block: ensure bdi->io_pages is always initializedJens Axboe
If a driver leaves the limit settings as the defaults, then we don't initialize bdi->io_pages. This means that file systems may need to work around bdi->io_pages == 0, which is somewhat messy. Initialize the default value just like we do for ->ra_pages. Cc: stable@vger.kernel.org Fixes: 9491ae4aade6 ("mm: don't cap request size based on read-ahead setting") Reported-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-09-01ALSA: pcm: oss: Remove superfluous WARN_ON() for mulaw sanity checkTakashi Iwai
The PCM OSS mulaw plugin has a check of the format of the counter part whether it's a linear format. The check is with snd_BUG_ON() that emits WARN_ON() when the debug config is set, and it confuses syzkaller as if it were a serious issue. Let's drop snd_BUG_ON() for avoiding that. While we're at it, correct the error code to a more suitable, EINVAL. Reported-by: syzbot+23b22dc2e0b81cbfcc95@syzkaller.appspotmail.com Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200901131802.18157-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de>
2020-09-01MIPS: perf: Fix wrong check condition of Loongson event IDsTiezhu Yang
According to the user's manual chapter 8.2.1 of Loongson 3A2000 CPU [1] and 3A3000 CPU [2], we should take some event IDs such as 274, 358, 359 and 360 as valid in the check condition, otherwise they are recognized as "not supported", fix it. [1] http://www.loongson.cn/uploadfile/cpu/3A2000/Loongson3A2000_user2.pdf [2] http://www.loongson.cn/uploadfile/cpu/3A3000/Loongson3A3000_3B3000user2.pdf Fixes: e9dfbaaeef1c ("MIPS: perf: Add hardware perf events support for new Loongson-3") Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn> Acked-by: Huang Pei <huangpei@loongson.cn> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-09-01clang-format: Update with the latest for_each macro listMiguel Ojeda
Re-run the shell fragment that generated the original list. Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
2020-09-01HID: core: Sanitize event code and type when mapping inputMarc Zyngier
When calling into hid_map_usage(), the passed event code is blindly stored as is, even if it doesn't fit in the associated bitmap. This event code can come from a variety of sources, including devices masquerading as input devices, only a bit more "programmable". Instead of taking the event code at face value, check that it actually fits the corresponding bitmap, and if it doesn't: - spit out a warning so that we know which device is acting up - NULLify the bitmap pointer so that we catch unexpected uses Code paths that can make use of untrusted inputs can now check that the mapping was indeed correct and bail out if not. Cc: stable@vger.kernel.org Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
2020-09-01HID: core: Correctly handle ReportSize being zeroMarc Zyngier
It appears that a ReportSize value of zero is legal, even if a bit non-sensical. Most of the HID code seems to handle that gracefully, except when computing the total size in bytes. When fed as input to memset, this leads to some funky outcomes. Detect the corner case and correctly compute the size. Cc: stable@vger.kernel.org Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
2020-09-01drm/i915: Add HDCP 1.4 support for MST connectorsSean Paul
Now that all the groundwork has been laid, we can turn on HDCP 1.4 over MST. Everything except for toggling the HDCP signalling and HDCP 2.2 support is the same as the DP case, so we'll re-use those callbacks Cc: Juston Li <juston.li@intel.com> Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-12-sean@poorly.run #v1 Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-13-sean@poorly.run #v2 Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-13-sean@poorly.run #v3 Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-15-sean@poorly.run #v4 Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-17-sean@poorly.run #v5 Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-17-sean@poorly.run #v6 Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-18-sean@poorly.run #v7 Changes in v2: -Toggle HDCP from encoder disable/enable -Don't disable HDCP on MST connector destroy, leave that for encoder disable, just ensure the check_work routine isn't running any longer Changes in v3: -Place the shim in the new intel_dp_hdcp.c file (Ville) Changes in v4: -Actually use the mst shim for mst connections (Juston) -Use QUERY_STREAM_ENC_STATUS MST message to verify channel is encrypted Changes in v5: -Add sleep on disable signalling to match hdmi delay Changes in v6: -Disable HDCP over MST on GEN12+ since I'm unsure how it should work and I don't have hardware to test it Changes in v7: -Remove hdcp2 shims for MST in favor of skipping hdcp2 init (Ramalingam) Changes in v8: -None Signed-off-by: Ramalingam C <ramalingam.c@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-18-sean@poorly.run
2020-09-01drm/i915: Print HDCP version info for all connectorsSean Paul
De-duplicate the HDCP version code for each connector and print it for all connectors. Cc: Juston Li <juston.li@intel.com> Cc: Ramalingam C <ramalingam.c@intel.com> Reviewed-by: Juston Li <juston.li@intel.com> Reviewed-by: Ramalingam C <ramalingam.c@intel.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200227185714.171466-1-sean@poorly.run #v4 Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-16-sean@poorly.run #v5 Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-16-sean@poorly.run #v6 Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-17-sean@poorly.run #v7 Changes in v4: - Added to the set Changes in v5: -Print "No connector support" for hdcp sink capability as well (Ram) Changes in v6: -None Changes in v7: -None Changes in v8: -None Signed-off-by: Ramalingam C <ramalingam.c@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-17-sean@poorly.run
2020-09-01drm/mst: Add support for QUERY_STREAM_ENCRYPTION_STATUS MST sideband messageSean Paul
Used to query whether an MST stream is encrypted or not. Cc: Lyude Paul <lyude@redhat.com> Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-14-sean@poorly.run #v4 Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-15-sean@poorly.run #v5 Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-15-sean@poorly.run #v6 Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-16-sean@poorly.run #v7 Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-16-sean@poorly.run #v8 Changes in v4: -Added to the set Changes in v5: -None Changes in v6: -Use FIELD_PREP to generate request buffer bitfields (Lyude) -Add mst selftest and dump/decode_sideband_req for QSES (Lyude) Changes in v7: -None Changes in v8: -Reverse the parsing on the hdcp_*x_device_present bits and leave breadcrumb in case this is incorrect (Anshuman) Changes in v8.5: -s/DRM_DEBUG_KMS/drm_dbg_kms/ (Lyude) Signed-off-by: Ramalingam C <ramalingam.c@intel.com> Acked-by: Daniel Vetter <daniel@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20200819143133.46232-1-sean@poorly.run
2020-09-01drm/i915: Add connector to hdcp_shim->check_link()Sean Paul
Currently we derive the connector from digital port in check_link(). For MST, this isn't sufficient since the digital port passed into the function can have multiple connectors downstream. This patch adds connector to the check_link() arguments so we have it when we need it. Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com> Reviewed-by: Ramalingam C <ramalingam.c@intel.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-13-sean@poorly.run #v4 Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-14-sean@poorly.run #v5 Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-14-sean@poorly.run #v6 Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-15-sean@poorly.run #v7 Changes in v4: -Added to the set Changes in v5: -None Changes in v6: -None Changes in v7: -None Changes in v8: -None Signed-off-by: Ramalingam C <ramalingam.c@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-15-sean@poorly.run
2020-09-01drm/i915: Plumb port through hdcp initSean Paul
This patch plumbs port through hdcp init instead of relying on intel_attached_encoder() to return a non-NULL encoder which won't work for MST connectors. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com> Reviewed-by: Ramalingam C <ramalingam.c@intel.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-13-sean@poorly.run #v5 Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-13-sean@poorly.run #v6 Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-14-sean@poorly.run #v7 Changes in v5: -Added to the set Changes in v6: -None Changes in v7: -None Changes in v8: -None Signed-off-by: Ramalingam C <ramalingam.c@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-14-sean@poorly.run
2020-09-01drm/i915: Factor out HDCP shim functions from dp for use by dp_mstSean Paul
These functions are all the same for dp and dp_mst, so move them into a dedicated file for both sst and mst to use. Reviewed-by: Ramalingam C <ramalingam.c@intel.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-11-sean@poorly.run #v1 Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-12-sean@poorly.run #v2 Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-12-sean@poorly.run #v3 Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-12-sean@poorly.run #v4 Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-12-sean@poorly.run #v5 Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-12-sean@poorly.run #v6 Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-13-sean@poorly.run #v7 Changes in v2: -None Changes in v3: -Created intel_dp_hdcp.c for the shared functions to live (Ville) Changes in v4: -Rebased on new drm logging change Changes in v5: -None Changes in v6: -None Changes in v7: -Rebased patch Changes in v8: -None Signed-off-by: Ramalingam C <ramalingam.c@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-13-sean@poorly.run
2020-09-01drm/i915: Use ddi_update_pipe in intel_dp_mstSean Paul
In order to act upon content_protection property changes, we'll need to implement the .update_pipe() hook. We can re-use intel_ddi_update_pipe for this Reviewed-by: Ramalingam C <ramalingam.c@intel.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-10-sean@poorly.run #v1 Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-11-sean@poorly.run #v2 Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-11-sean@poorly.run #v3 Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-11-sean@poorly.run #v4 Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-11-sean@poorly.run #v5 Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-11-sean@poorly.run #v6 Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-12-sean@poorly.run #v7 Changes in v2: -None Changes in v3: -None Changes in v4: -None Changes in v5: -None Changes in v6: -None Changes in v7: -None Changes in v8: -None Signed-off-by: Ramalingam C <ramalingam.c@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-12-sean@poorly.run
2020-09-01drm/i915: Support DP MST in enc_to_dig_port() functionSean Paul
Although DP_MST fake encoders are not subclassed from digital ports, they are associated with them. Support these encoders. Reviewed-by: Ramalingam C <ramalingam.c@intel.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-9-sean@poorly.run #v1 Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-10-sean@poorly.run #v2 Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-10-sean@poorly.run #v3 Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-10-sean@poorly.run #v4 Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-10-sean@poorly.run #v5 Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-10-sean@poorly.run #v6 Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-11-sean@poorly.run #v7 Changes in v2: -None Changes in v3: -None Changes in v4: -None Changes in v5: -None Changes in v6: -None Changes in v7: -None Changes in v8: -None Signed-off-by: Ramalingam C <ramalingam.c@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-11-sean@poorly.run
2020-09-01drm/i915: Don't fully disable HDCP on a port if multiple pipes are using itSean Paul
This patch is required for HDCP over MST. If a port is being used for multiple HDCP streams, we don't want to fully disable HDCP on a port if one of them is disabled. Instead, we just disable the HDCP signalling on that particular pipe and exit early. The last pipe to disable HDCP will also bring down HDCP on the port. In order to achieve this, we need to keep a refcount in intel_digital_port and protect it using a new hdcp_mutex. Cc: Ramalingam C <ramalingam.c@intel.com> Reviewed-by: Ramalingam C <ramalingam.c@intel.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-8-sean@poorly.run #v1 Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-9-sean@poorly.run #v2 Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-9-sean@poorly.run #v3 Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-9-sean@poorly.run #v4 Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-9-sean@poorly.run #v5 Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-9-sean@poorly.run #v6 Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-10-sean@poorly.run #v7 Changes in v2: -Move the toggle_signalling call into _intel_hdcp_disable so it's called from check_work Changes in v3: -None Changes in v4: -None Changes in v5: -Change WARN_ON to drm_WARN_ON Changes in v6: -None Changes in v7: -Split minor intel_hdcp_disable refactor into separate patch (Ramalingam) Changes in v8: -None Signed-off-by: Ramalingam C <ramalingam.c@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-10-sean@poorly.run
2020-09-01drm/i915: Clean up intel_hdcp_disableSean Paul
Add an out label and un-indent hdcp disable in preparation for hdcp_mutex. No functional changes Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com> Reviewed-by: Ramalingam C <ramalingam.c@intel.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-9-sean@poorly.run #v6 Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-9-sean@poorly.run #v7 Changes in v7: -Split into separate patch (Ramalingam) Changes in v8: -None Signed-off-by: Ramalingam C <ramalingam.c@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-9-sean@poorly.run
2020-09-01drm/i915: Protect workers against disappearing connectorsSean Paul
This patch adds some protection against connectors being destroyed before the HDCP workers are finished. For check_work, we do a synchronous cancel after the connector is unregistered which will ensure that it is finished before destruction. In the case of prop_work, we can't do a synchronous wait since it needs to take connection_mutex which could cause deadlock. Instead, we'll take a reference on the connector when scheduling prop_work and give it up once we're done. Reviewed-by: Ramalingam C <ramalingam.c@intel.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-8-sean@poorly.run #v2 Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-8-sean@poorly.run #v3 Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-8-sean@poorly.run #v4 Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-8-sean@poorly.run #v5 Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-8-sean@poorly.run #v6 Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-8-sean@poorly.run #v7 Changes in v2: -Added to the set Changes in v3: -Change the WARN_ON condition in intel_hdcp_cleanup to allow for initializing connectors as well Changes in v4: -None Changes in v5: -Change WARN_ON to drm_WARN_ON Changes in v6: -None Changes in v7: -None Changes in v8: -None Signed-off-by: Ramalingam C <ramalingam.c@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-8-sean@poorly.run
2020-09-01drm/i915: Factor out hdcp->value assignmentsSean Paul
This is a bit of housecleaning for a future patch. Instead of sprinkling hdcp->value assignments and prop_work scheduling everywhere, introduce a function to do it for us. Reviewed-by: Ramalingam C <ramalingam.c@intel.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-7-sean@poorly.run #v1 Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-7-sean@poorly.run #v2 Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-7-sean@poorly.run #v3 Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-7-sean@poorly.run #v4 Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-7-sean@poorly.run #v5 Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-7-sean@poorly.run #v6 Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-7-sean@poorly.run #v7 Changes in v2: -None Changes in v3: -None Changes in v4: -Rebased on top of drm_* logging changes Changes in v5: -Change WARN_ON to drm_WARN_ON Changes in v6: -None Changes in v7: -None Changes in v8: -None Signed-off-by: Ramalingam C <ramalingam.c@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-7-sean@poorly.run
2020-09-01drm/i915: Use the cpu_transcoder in intel_hdcp to toggle HDCP signallingSean Paul
Instead of using intel_dig_port's encoder pipe to determine which transcoder to toggle signalling on, use the cpu_transcoder field already stored in intel_hdmi. This is particularly important for MST. Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ramalingam C <ramalingam.c@intel.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-6-sean@poorly.run #v2 Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-6-sean@poorly.run #v3 Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-6-sean@poorly.run #v4 Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-6-sean@poorly.run #v5 Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-6-sean@poorly.run #v6 Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-6-sean@poorly.run #v7 Changes in v2: -Added to the set Changes in v3: -s/hdcp/hdmi/ in commit msg (Ram) Changes in v4: -Rebased on intel_de_(read|write) change Changes in v5: -Update hdcp->cpu_transcoder in intel_hdcp_enable so it works with pipe != 0 Changes in v6: -None Changes in v7: -None Changes in v8: -None Signed-off-by: Ramalingam C <ramalingam.c@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-6-sean@poorly.run
2020-09-01drm/i915: Intercept Aksv writes in the aux hooksSean Paul
Instead of hand rolling the transfer ourselves in the hdcp hook, inspect aux messages and add the aksv flag in the aux transfer hook. IIRC, this was the original implementation and folks wanted this hack to be isolated to the hdcp code, which makes sense. However in testing an LG monitor on my desk, I noticed it was passing back a DEFER reply. This wasn't handled in our hand-rolled code and HDCP auth was failing as a result. Instead of copy/pasting all of the retry logic and delays from drm dp helpers, let's just use the helpers and hide the aksv select as best as we can. Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ramalingam C <ramalingam.c@intel.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-3-sean@poorly.run #v1 Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-5-sean@poorly.run #v2 Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-5-sean@poorly.run #v3 Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-5-sean@poorly.run #v4 Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-5-sean@poorly.run #v5 Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-5-sean@poorly.run #v6 Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-5-sean@poorly.run #v7 Changes in v2: -Remove 'generate' in intel_dp_aux_generate_xfer_flags, make arg const (Ville) -Bundle Aksv if statement together (Ville) -Rename 'txbuf' to 'aksv' (Ville) Changes in v3: -None Changes in v4: -None Changes in v5: -None Changes in v6: -None Changes in v7: -None Changes in v8: -None Signed-off-by: Ramalingam C <ramalingam.c@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-5-sean@poorly.run
2020-09-01drm/i915: WARN if HDCP signalling is enabled upon disableSean Paul
HDCP signalling should not be left on, WARN if it is Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Ramalingam C <ramalingam.c@intel.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-4-sean@poorly.run #v2 Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-4-sean@poorly.run #v3 Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-4-sean@poorly.run #v4 Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-4-sean@poorly.run #v5 Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-4-sean@poorly.run #v6 Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-4-sean@poorly.run #v7 Changes in v2: -Added to the set in lieu of just clearing the bit Changes in v3: -None Changes in v4: -None Changes in v5: -Change WARN_ON to drm_WARN_ON Changes in v6: -None Changes in v7: -Rebased, variable name changed from 'ctl' to 'val' Changes in v8: -None Signed-off-by: Ramalingam C <ramalingam.c@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-4-sean@poorly.run
2020-09-01drm/i915: Clear the repeater bit on HDCP disableSean Paul
On HDCP disable, clear the repeater bit. This ensures if we connect a non-repeater sink after a repeater, the bit is in the state we expect. Fixes: ee5e5e7a5e0f ("drm/i915: Add HDCP framework + base implementation") Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ramalingam C <ramalingam.c@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Sean Paul <seanpaul@chromium.org> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: intel-gfx@lists.freedesktop.org Cc: <stable@vger.kernel.org> # v4.17+ Reviewed-by: Ramalingam C <ramalingam.c@intel.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-3-sean@poorly.run #v2 Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-3-sean@poorly.run #v3 Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-3-sean@poorly.run #v4 Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-3-sean@poorly.run #v5 Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-3-sean@poorly.run #v6 Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-3-sean@poorly.run #v7 Changes in v2: -Added to the set Changes in v3: -None I had previously agreed that clearing the rep_ctl bits on enable would also be a good idea. However when I committed that idea to code, it didn't look right. So let's rely on enables and disables being paired and everything outside of that will be considered a bug Changes in v4: -s/I915_(READ|WRITE)/intel_de_(read|write)/ Changes in v5: -None Changes in v6: -None Changes in v7: -None Changes in v8: -None Signed-off-by: Ramalingam C <ramalingam.c@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-3-sean@poorly.run
2020-09-01drm/i915: Fix sha_text population codeSean Paul
This patch fixes a few bugs: 1- We weren't taking into account sha_leftovers when adding multiple ksvs to sha_text. As such, we were or'ing the end of ksv[j - 1] with the beginning of ksv[j] 2- In the sha_leftovers == 2 and sha_leftovers == 3 case, bstatus was being placed on the wrong half of sha_text, overlapping the leftover ksv value 3- In the sha_leftovers == 2 case, we need to manually terminate the byte stream with 0x80 since the hardware doesn't have enough room to add it after writing M0 The upside is that all of the HDCP supported HDMI repeaters I could find on Amazon just strip HDCP anyways, so it turns out to be _really_ hard to hit any of these cases without an MST hub, which is not (yet) supported. Oh, and the sha_leftovers == 1 case works perfectly! Fixes: ee5e5e7a5e0f ("drm/i915: Add HDCP framework + base implementation") Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ramalingam C <ramalingam.c@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Sean Paul <seanpaul@chromium.org> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: intel-gfx@lists.freedesktop.org Cc: <stable@vger.kernel.org> # v4.17+ Reviewed-by: Ramalingam C <ramalingam.c@intel.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-2-sean@poorly.run #v1 Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-2-sean@poorly.run #v2 Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-2-sean@poorly.run #v3 Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-2-sean@poorly.run #v4 Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-2-sean@poorly.run #v5 Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-2-sean@poorly.run #v6 Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-2-sean@poorly.run #v7 Changes in v2: -None Changes in v3: -None Changes in v4: -Rebased on intel_de_write changes Changes in v5: -None Changes in v6: -None Changes in v7: -None Changes in v8: -None Signed-off-by: Ramalingam C <ramalingam.c@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-2-sean@poorly.run
2020-09-01HID: elan: Fix memleak in elan_input_configuredDinghao Liu
When input_mt_init_slots() fails, input should be freed to prevent memleak. When input_register_device() fails, we should call input_mt_destroy_slots() to free memory allocated by input_mt_init_slots(). Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2020-08-31drm/nouveau/kms: Start using drm_dp_read_dpcd_caps()Lyude Paul
Now that we've extracted i915's code for reading both the normal DPCD caps and extended DPCD caps into a shared helper, let's start using this in nouveau to enable us to start checking extended DPCD caps for free. Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Ben Skeggs <bskeggs@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-21-lyude@redhat.com
2020-08-31drm/i915/dp: Extract drm_dp_read_dpcd_caps()Lyude Paul
Since DP 1.3, it's been possible for DP receivers to specify an additional set of DPCD capabilities, which can take precedence over the capabilities reported at DP_DPCD_REV. Basically any device supporting DP is going to need to read these in an identical manner, in particular nouveau, so let's go ahead and just move this code out of i915 into a shared DRM DP helper that we can use in other drivers. v2: * Remove redundant dpcd[DP_DPCD_REV] == 0 check * Fix drm_dp_dpcd_read() ret checks Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Sean Paul <sean@poorly.run> Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-20-lyude@redhat.com
2020-08-31drm/nouveau/kms: Don't change EDID when it hasn't actually changedLyude Paul
Currently in nouveau_connector_ddc_detect() and nouveau_connector_detect_lvds(), we start the connector probing process by releasing the previous EDID and informing DRM of the change. However, since commit 5186421cbfe2 ("drm: Introduce epoch counter to drm_connector") drm_connector_update_edid_property() actually checks whether the new EDID we've specified is different from the previous one, and updates the connector's epoch accordingly if it is. But, because we always set the EDID to NULL first in nouveau_connector_ddc_detect() and nouveau_connector_detect_lvds() we end up making DRM think that the EDID changes every single time we do a connector probe - which isn't needed. So, let's fix this by not clearing the EDID at the start of the connector probing process, and instead simply changing or removing it once near the end of the probing process. This will help prevent us from sending unneeded hotplug events to userspace when nothing has actually changed. Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Ben Skeggs <bskeggs@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-19-lyude@redhat.com
2020-08-31drm/nouveau/kms/nv50-: Add support for DP_SINK_COUNTLyude Paul
This is another bit that we never implemented for nouveau: dongle detection. When a "dongle", e.g. an active display adaptor, is hooked up to the system and causes an HPD to be fired, we don't actually know whether or not there's anything plugged into the dongle without checking the sink count. As a result, plugging in a dongle without anything plugged into it currently results in a bogus EDID retrieval error in the kernel log. Additionally, most dongles won't send another long HPD signal if the user suddenly plugs something in, they'll only send a short HPD IRQ with the expectation that the source will check the sink count and reprobe the connector if it's changed - something we don't actually do. As a result, nothing will happen if the user plugs the dongle in before plugging something into the dongle. So, let's fix this by checking the sink count in both nouveau_dp_probe_dpcd() and nouveau_dp_irq(), and reprobing the connector if things change. Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Ben Skeggs <bskeggs@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-18-lyude@redhat.com
2020-08-31drm/i915/dp: Extract drm_dp_read_sink_count()Lyude Paul
And of course, we'll also need to read the sink count from other drivers as well if we're checking whether or not it's supported. So, let's extract the code for this into another helper. v2: * Fix drm_dp_dpcd_readb() ret check * Add back comment and move back sink_count assignment in intel_dp_get_dpcd() v5: * Change name from drm_dp_get_sink_count() to drm_dp_read_sink_count() * Also, add "See also:" section to kdocs Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Sean Paul <sean@poorly.run> Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-17-lyude@redhat.com
2020-08-31drm/i915/dp: Extract drm_dp_read_sink_count_cap()Lyude Paul
Since other drivers are also going to need to be aware of the sink count in order to do proper dongle detection, we might as well steal i915's DP_SINK_COUNT helpers and move them into DRM helpers so that other dirvers can use them as well. Note that this also starts using intel_dp_has_sink_count() in intel_dp_detect_dpcd(), which is a functional change. v5: * Change name from drm_dp_has_sink_count() to drm_dp_read_sink_count_cap() Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Sean Paul <sean@poorly.run> Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-16-lyude@redhat.com
2020-08-31drm/nouveau/kms/nv50-: Use downstream DP clock limits for mode validationLyude Paul
This adds support for querying the maximum clock rate of a downstream port on a DisplayPort connection. Generally, downstream ports refer to active dongles which can have their own pixel clock limits. Note as well, we also start marking the connector as disconnected if we can't read the DPCD, since we wouldn't be able to do anything without DPCD access anyway. Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Ben Skeggs <bskeggs@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-15-lyude@redhat.com
generated by cgit (git 2.34.1) at 2025-09-12 13:04:51 +0000