| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds code to handle the BSS_CHANGED_BSS_COLOR flag. It will
trigger the propagation of BSS color settings into the FW. Handling is
slightly different between AP and STA interfaces.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
If the he_operation field of the beacon sets a BSS color, we need to inform
the FW of the settings. This patch adds the WMI command handlers required
to do so.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The driver currently does not use wake_txq_queue. This leads to the
tx_queue_len being defaulted to 1000. Setting this parameter will
change the queue_len to 4096 which is more fitting for HE.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Enabling PN checking in the hardware; hardware checks
the PN of the received packets and reports the errors
to the host for further handling; default action is to
drop such packets. TSC (TKIP sequence counter)
validation is also offloaded.
Hardware validates PN/TSC only for unicast packets;
for group addressed packets, PN validation is done
in mac80211.
PN errors are reported to the driver via WBM RX release
ring and can be dumped by using the following command.
"cat /sys/kernel/debug/ath11k/soc_rx_stats | grep -i pn"
Sample Output:
PN check fail: 210
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
IPQ8074 HW has support to verify the PN of the received frames.
For all frames except for fragmented ones, HW checks the PN and
delivers them to the driver. For fragmented frames, driver is
required to do a little more; it has to reassemble the fragments
and then reinject them to the HW for verifying the PN. Currently,
to keep the logic simple, PN verifcation is disabled in HW and is
handled in mac80211 for all the frames (fragmented and unfragmented).
On the contrary, offloading PN Validation to the HW brings important
benefits. It reduces CPU cycles spent on the host CPU for verifying
the same; helps in enabling features which improve performance like
mac80211 fast RX path, enabling multiple REO rings for parallel RX
processing, 802.11 decapsulation offloading. All these features are
dependent on PN offload which in turn is dependent on handling of
the received fragments in the driver.
When TKIP security is used, additional handling is required while
processing the fragments; since MIC is computed on an MSDU in TKIP,
only the last fragment has the MIC info. In this case, driver has to
compute the MIC after reassembly and compare it against the MIC
present in the frame. For this, MICHAEL_MIC kernel crypto library
APIs are used and the dependencies are appropriately set.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Clang warns:
../drivers/net/ethernet/mellanox/mlx5/core/mr.c:63:21: warning: variable
'key' is uninitialized when used here [-Wuninitialized]
mkey_index, key, mkey->key);
^~~
../drivers/net/ethernet/mellanox/mlx5/core/mlx5_core.h:54:6: note:
expanded from macro 'mlx5_core_dbg'
##__VA_ARGS__)
^~~~~~~~~~~
../include/linux/dev_printk.h:114:39: note: expanded from macro
'dev_dbg'
dynamic_dev_dbg(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~
../include/linux/dynamic_debug.h:158:19: note: expanded from macro
'dynamic_dev_dbg'
dev, fmt, ##__VA_ARGS__)
^~~~~~~~~~~
../include/linux/dynamic_debug.h:143:56: note: expanded from macro
'_dynamic_func_call'
__dynamic_func_call(__UNIQUE_ID(ddebug), fmt, func, ##__VA_ARGS__)
^~~~~~~~~~~
../include/linux/dynamic_debug.h:125:15: note: expanded from macro
'__dynamic_func_call'
func(&id, ##__VA_ARGS__); \
^~~~~~~~~~~
../drivers/net/ethernet/mellanox/mlx5/core/mr.c:47:8: note: initialize
the variable 'key' to silence this warning
u8 key;
^
= '\0'
1 warning generated.
key's initialization was removed in commit fc6a9f86f08a ("{IB,net}/mlx5:
Assign mkey variant in mlx5_ib only") but its use was not fully removed.
Remove it now so that there is no more warning.
Fixes: fc6a9f86f08a ("{IB,net}/mlx5: Assign mkey variant in mlx5_ib only")
Link: https://github.com/ClangBuiltLinux/linux/issues/932
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Pengcheng Yang says:
====================
tcp: fix stretch ACK bugs in congestion control modules
"stretch ACKs" (caused by LRO, GRO, delayed ACKs or middleboxes)
can cause serious performance shortfalls in common congestion
control algorithms. Neal Cardwell submitted a series of patches
starting with commit e73ebb0881ea ("tcp: stretch ACK fixes prep")
to handle stretch ACKs and fixed stretch ACK bugs in Reno and
CUBIC congestion control algorithms.
This patch series continues to fix bic, scalable, veno and yeah
congestion control algorithms to handle stretch ACKs.
Changes in v2:
- Provide [PATCH 0/N] to describe the modifications of this patch series
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change Yeah to properly handle stretch ACKs in additive
increase mode by passing in the count of ACKed packets
to tcp_cong_avoid_ai().
In addition, we re-implemented the scalable path using
tcp_cong_avoid_ai() and removed the pkts_acked variable.
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change Veno to properly handle stretch ACKs in additive
increase mode by passing in the count of ACKed packets
to tcp_cong_avoid_ai().
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No code logic has been changed in this patch.
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change Scalable to properly handle stretch ACKs in additive
increase mode by passing in the count of ACKed packets to
tcp_cong_avoid_ai().
In addition, because we are now precisely accounting for
stretch ACKs, including delayed ACKs, we can now change
TCP_SCALABLE_AI_CNT to 100.
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changes BIC to properly handle stretch ACKs in additive
increase mode by passing in the count of ACKed packets
to tcp_cong_avoid_ai().
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
XDP-redirect is broken in this driver sfc. XDP_REDIRECT requires
tailroom for skb_shared_info when creating an SKB based on the
redirected xdp_frame (both in cpumap and veth).
The fix requires some initial explaining. The driver uses RX page-split
when possible. It reserves the top 64 bytes in the RX-page for storing
dma_addr (struct efx_rx_page_state). It also have the XDP recommended
headroom of XDP_PACKET_HEADROOM (256 bytes). As it doesn't reserve any
tailroom, it can still fit two standard MTU (1500) frames into one page.
The sizeof struct skb_shared_info in 320 bytes. Thus drivers like ixgbe
and i40e, reduce their XDP headroom to 192 bytes, which allows them to
fit two frames with max 1536 bytes into a 4K page (192+1536+320=2048).
The fix is to reduce this drivers headroom to 128 bytes and add the 320
bytes tailroom. This account for reserved top 64 bytes in the page, and
still fit two frame in a page for normal MTUs.
We must never go below 128 bytes of headroom for XDP, as one cacheline
is for xdp_frame area and next cacheline is reserved for metadata area.
Fixes: eb9a36be7f3e ("sfc: perform XDP processing on received packets")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even though INITRAMFS_SOURCE kconfig option isn't set in most of
defconfigs it is used (set) extensively by various build systems.
Commit f26661e12765 ("initramfs: make initramfs compression choice
non-optional") has changed default compression mode. Previously we
compress initramfs using available compression algorithm. Now
we don't use any compression at all by default.
It significantly increases the image size in case of build system
chooses embedded initramfs. Initially I faced with this issue while
using buildroot.
As of today it's not possible to set preferred compression mode
in target defconfig as this option depends on INITRAMFS_SOURCE
being set. Modification of all build systems either doesn't look
like good option.
Let's instead rewrite initramfs compression mode choices list
the way that "INITRAMFS_COMPRESSION_NONE" will be the last option
in the list. In that case it will be chosen only if all other
options (which implements any compression) are not available.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Rearrange the config files for remoteproc and IPA to fix their
interdependencies.
First, have CONFIG_QCOM_Q6V5_MSS select QCOM_Q6V5_IPA_NOTIFY so the
notification code is built regardless of whether IPA needs it.
Next, represent QCOM_IPA as being dependent on QCOM_Q6V5_MSS rather
than setting its value to match QCOM_Q6V5_COMMON (which is selected
by QCOM_Q6V5_MSS).
Drop all dependencies from QCOM_Q6V5_IPA_NOTIFY. The notification
code will be built whenever QCOM_Q6V5_MSS is set, and it has no other
dependencies.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The fix referenced below causes a crash when an ERSPAN tunnel is created
without passing IFLA_INFO_DATA. Fix by validating passed-in data in the
same way as ipgre does.
Fixes: e1f8f78ffe98 ("net: ip_gre: Separate ERSPAN newlink / changelink callbacks")
Reported-by: syzbot+1b4ebf4dae4e510dd219@syzkaller.appspotmail.com
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This path fixes the suspicious RCU usage warning reported by
kernel test robot.
net/kcm/kcmproc.c:#RCU-list_traversed_in_non-reader_section
There is no need to use list_for_each_entry_rcu() in
kcm_stats_seq_show() as the list is always traversed under
knet->mutex held.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to preserve backwards compatability with kmod tools, we have to
move the namespace field in Module.symvers last, as the depmod -e -E
option looks at the first three fields in Module.symvers to check symbol
versions (and it's expected they stay in the original order of crc,
symbol, module).
In addition, update an ancient comment above read_dump() in modpost that
suggested that the export type field in Module.symvers was optional. I
suspect that there were historical reasons behind that comment that are
no longer accurate. We have been unconditionally printing the export
type since 2.6.18 (commit bd5cbcedf44), which is over a decade ago now.
Fix up read_dump() to treat each field as non-optional. I suspect the
original read_dump() code treated the export field as optional in order
to support pre <= 2.6.18 Module.symvers (which did not have the export
type field). Note that although symbol namespaces are optional, the
field will not be omitted from Module.symvers if a symbol does not have
a namespace. In this case, the field will simply be empty and the next
delimiter or end of line will follow.
Cc: stable@vger.kernel.org
Fixes: cb9b55d21fe0 ("modpost: add support for symbol namespaces")
Tested-by: Matthias Maennich <maennich@google.com>
Reviewed-by: Matthias Maennich <maennich@google.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Pull ARM fixes from Russell King:
- allow use of ARMv8 arch timer in 32-bit VDSO
- rename missed .fixup section
- fix kbuild issue with stack protector GCC plugin
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8961/2: Fix Kbuild issue caused by per-task stack protector GCC plugin
ARM: 8958/1: rename missed uaccess .fixup section
ARM: 8957/1: VDSO: Match ARMv8 timer in cntvct_functional()
|
|
For the case where the last mvneta_poll did not process all
RX packets, we need to xor the pp->cause_rx_tx or port->cause_rx_tx
before claculating the rx_queue.
Fixes: 2dcf75e2793c ("net: mvneta: Associate RX queues with each CPU")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
printk in macro vxge_debug_ll uses __VA_ARGS__ without "##" prefix,
it causes a build error when there is no variable
arguments(e.g. only fmt is specified.).
Signed-off-by: Zheng Wei <wei.zheng@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove set but not used variables 'sw_comp_cons' and 'hw_comp_cons'
to fix gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/qlogic/qede/qede_ethtool.c: In function qede_selftest_receive_traffic:
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:1569:20:
warning: variable sw_comp_cons set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/qlogic/qede/qede_ethtool.c: In function qede_selftest_receive_traffic:
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:1569:6:
warning: variable hw_comp_cons set but not used [-Wunused-but-set-variable]
After removing 'hw_comp_cons',the memory barrier 'rmb()' and its comments become useless,
so remove them as well.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Zengkai <zhengzengkai@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Madalin Bucur says:
====================
QorIQ DPAA ARM RDBs need internal delay on RGMII
v2: used phy_interface_mode_is_rgmii() to identify RGMII
The QorIQ DPAA 1 based RDB boards require internal delay on
both Tx and Rx to be set. The patch set ensures all RGMII
modes are treated correctly by the FMan driver and sets the
phy-connection-type to "rgmii-id" to restore functionality.
Previously Rx internal delay was set by board pull-ups and
was left untouched by the PHY driver. Since commit
1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY
driver has control over the RGMII RX delay and it is
disabling it for other modes than RGMII_RXID and RGMII_ID.
Please note that u-boot in particular performs a fix-up of
the PHY connection type and will overwrite the values from
the Linux device tree. Another patch set was sent for u-boot
and one needs to apply that [1] to the boot loader, to ensure
this fix is complete, unless a different bootloader is used.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The correct setting for the RGMII ports on LS1046ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit 1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1046ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii".
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: 3fa395d2c48a ("arm64: dts: add LS1046A DPAA FMan nodes")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The correct setting for the RGMII ports on LS1043ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit 1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1043ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii_txid".
This issue was not apparent at the time as the PHY driver took the
same action for RGMII_TXID and RGMII_ID back then but it became
visible (RX no longer working) after the above patch.
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: bf02f2ffe59c ("arm64: dts: add LS1043A DPAA FMan support")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Treat all internal delay variants the same as RGMII.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A lenovo pixart mouse (17ef:608d) is afflicted common the the malfunction
where it disconnects and reconnects every minute--each time incrementing
the device number. This patch adds the device id of the device and
specifies that it needs the HID_QUIRK_ALWAYS_POLL quirk in order to
work properly.
Signed-off-by: Tony Fischetti <tony.fischetti@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Currently enabling clkctrl clock on am4 can fail for RTC as the clock
parent is wrong for RTC.
Fixes: 76a1049b84dd ("clk: ti: am43xx: add new clkctrl data for am43xx")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lkml.kernel.org/r/20200221171030.39326-1-tony@atomide.com
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
MP8867 is an I2C-controlled adjustable voltage regulator made by
Monolithic Power Systems. The difference between MP8867 and MP8869
are:
1.If V_BOOT, the vref of MP8869 is fixed at 600mv while vref of MP8867
is determined by the I2C control.
2.For MP8867, when setting voltage, if the steps is within 5, we need
to manually set the GO_BIT to 0.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200316223100.37805b22@xhacker
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
MP8867 is an I2C-controlled adjustable voltage regulator made by
Monolithic Power Systems. The difference between MP8867 and MP8869
are:
1.If V_BOOT, the vref of MP8869 is fixed at 600mv while vref of
MP8867 is determined by the I2C control.
2.For MP8867, when setting voltage, if the step is within 5, we
need to manually set the GO BIT to 0.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200316223127.4b1ecc92@xhacker
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The MP8869 from Monolithic Power Systems is a single output DC/DC
converter. The voltage can be controlled via I2C.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200316223020.1a6d92ae@xhacker
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The MP8869 from Monolithic Power Systems is a single output dc/dc
converter with voltage control over i2c.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200316222945.74ad34dd@xhacker
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-fixes
Pull a few more i.MX clk fixes for 5.6:
- A couple of fixes on i.MX8MP clock driver to correct HDMI_AXI and
ENET_QOS_ROOT parent clock
* tag 'imx-clk-fixes-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
clk: imx8mp: Correct the enet_qos parent clock
clk: imx8mp: Correct IMX8MP_CLK_HDMI_AXI clock parent
|
|
On a very heavily loaded D05 with GICv4, I managed to trigger the
following lockdep splat:
[ 6022.598864] ======================================================
[ 6022.605031] WARNING: possible circular locking dependency detected
[ 6022.611200] 5.6.0-rc4-00026-geee7c7b0f498 #680 Tainted: G E
[ 6022.618061] ------------------------------------------------------
[ 6022.624227] qemu-system-aar/7569 is trying to acquire lock:
[ 6022.629789] ffff042f97606808 (&p->pi_lock){-.-.}, at: try_to_wake_up+0x54/0x7a0
[ 6022.637102]
[ 6022.637102] but task is already holding lock:
[ 6022.642921] ffff002fae424cf0 (&irq_desc_lock_class){-.-.}, at: __irq_get_desc_lock+0x5c/0x98
[ 6022.651350]
[ 6022.651350] which lock already depends on the new lock.
[ 6022.651350]
[ 6022.659512]
[ 6022.659512] the existing dependency chain (in reverse order) is:
[ 6022.666980]
[ 6022.666980] -> #2 (&irq_desc_lock_class){-.-.}:
[ 6022.672983] _raw_spin_lock_irqsave+0x50/0x78
[ 6022.677848] __irq_get_desc_lock+0x5c/0x98
[ 6022.682453] irq_set_vcpu_affinity+0x40/0xc0
[ 6022.687236] its_make_vpe_non_resident+0x6c/0xb8
[ 6022.692364] vgic_v4_put+0x54/0x70
[ 6022.696273] vgic_v3_put+0x20/0xd8
[ 6022.700183] kvm_vgic_put+0x30/0x48
[ 6022.704182] kvm_arch_vcpu_put+0x34/0x50
[ 6022.708614] kvm_sched_out+0x34/0x50
[ 6022.712700] __schedule+0x4bc/0x7f8
[ 6022.716697] schedule+0x50/0xd8
[ 6022.720347] kvm_arch_vcpu_ioctl_run+0x5f0/0x978
[ 6022.725473] kvm_vcpu_ioctl+0x3d4/0x8f8
[ 6022.729820] ksys_ioctl+0x90/0xd0
[ 6022.733642] __arm64_sys_ioctl+0x24/0x30
[ 6022.738074] el0_svc_common.constprop.3+0xa8/0x1e8
[ 6022.743373] do_el0_svc+0x28/0x88
[ 6022.747198] el0_svc+0x14/0x40
[ 6022.750761] el0_sync_handler+0x124/0x2b8
[ 6022.755278] el0_sync+0x140/0x180
[ 6022.759100]
[ 6022.759100] -> #1 (&rq->lock){-.-.}:
[ 6022.764143] _raw_spin_lock+0x38/0x50
[ 6022.768314] task_fork_fair+0x40/0x128
[ 6022.772572] sched_fork+0xe0/0x210
[ 6022.776484] copy_process+0x8c4/0x18d8
[ 6022.780742] _do_fork+0x88/0x6d8
[ 6022.784478] kernel_thread+0x64/0x88
[ 6022.788563] rest_init+0x30/0x270
[ 6022.792390] arch_call_rest_init+0x14/0x1c
[ 6022.796995] start_kernel+0x498/0x4c4
[ 6022.801164]
[ 6022.801164] -> #0 (&p->pi_lock){-.-.}:
[ 6022.806382] __lock_acquire+0xdd8/0x15c8
[ 6022.810813] lock_acquire+0xd0/0x218
[ 6022.814896] _raw_spin_lock_irqsave+0x50/0x78
[ 6022.819761] try_to_wake_up+0x54/0x7a0
[ 6022.824018] wake_up_process+0x1c/0x28
[ 6022.828276] wakeup_softirqd+0x38/0x40
[ 6022.832533] __tasklet_schedule_common+0xc4/0xf0
[ 6022.837658] __tasklet_schedule+0x24/0x30
[ 6022.842176] check_irq_resend+0xc8/0x158
[ 6022.846609] irq_startup+0x74/0x128
[ 6022.850606] __enable_irq+0x6c/0x78
[ 6022.854602] enable_irq+0x54/0xa0
[ 6022.858431] its_make_vpe_non_resident+0xa4/0xb8
[ 6022.863557] vgic_v4_put+0x54/0x70
[ 6022.867469] kvm_arch_vcpu_blocking+0x28/0x38
[ 6022.872336] kvm_vcpu_block+0x48/0x490
[ 6022.876594] kvm_handle_wfx+0x18c/0x310
[ 6022.880938] handle_exit+0x138/0x198
[ 6022.885022] kvm_arch_vcpu_ioctl_run+0x4d4/0x978
[ 6022.890148] kvm_vcpu_ioctl+0x3d4/0x8f8
[ 6022.894494] ksys_ioctl+0x90/0xd0
[ 6022.898317] __arm64_sys_ioctl+0x24/0x30
[ 6022.902748] el0_svc_common.constprop.3+0xa8/0x1e8
[ 6022.908046] do_el0_svc+0x28/0x88
[ 6022.911871] el0_svc+0x14/0x40
[ 6022.915434] el0_sync_handler+0x124/0x2b8
[ 6022.919951] el0_sync+0x140/0x180
[ 6022.923773]
[ 6022.923773] other info that might help us debug this:
[ 6022.923773]
[ 6022.931762] Chain exists of:
[ 6022.931762] &p->pi_lock --> &rq->lock --> &irq_desc_lock_class
[ 6022.931762]
[ 6022.942101] Possible unsafe locking scenario:
[ 6022.942101]
[ 6022.948007] CPU0 CPU1
[ 6022.952523] ---- ----
[ 6022.957039] lock(&irq_desc_lock_class);
[ 6022.961036] lock(&rq->lock);
[ 6022.966595] lock(&irq_desc_lock_class);
[ 6022.973109] lock(&p->pi_lock);
[ 6022.976324]
[ 6022.976324] *** DEADLOCK ***
This is happening because we have a pending doorbell that requires
retrigger. As SW retriggering is done in a tasklet, we trigger the
circular dependency above.
The easy cop-out is to provide a retrigger callback that doesn't
require acquiring any extra lock.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200310184921.23552-5-maz@kernel.org
|
|
The irq_retrigger callback is supposed to return 0 when retrigger
has failed, and a non-zero value otherwise. Tell the core code
that the driver has succedded in using the HW to retrigger the
interrupt (if ever).
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200310184921.23552-4-maz@kernel.org
|
|
The irq_retrigger callback is supposed to return 0 when retrigger
has failed, and a non-zero value otherwise. Tell the core code
that the driver has succedded in using the HW to retrigger the
interrupt.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200310184921.23552-3-maz@kernel.org
|
|
The irq_retrigger callback is supposed to return 0 when retrigger
has failed, and a non-zero value otherwise. Tell the core code
that the driver has succedded in using the HW to retrigger the
interrupt.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200310184921.23552-2-maz@kernel.org
|
|
The GICv3 ITS driver assumes that once it has latched on a page size for
a given BASER register, it can use the same page size as the maximum
page size for all subsequent BASER registers.
Although it worked so far, nothing in the architecture guarantees this,
and Nianyao Tang hit this problem on some undisclosed implementation.
Let's bite the bullet and probe the the supported page size on all BASER
registers before starting to populate the tables. This simplifies the
setup a bit, at the expense of a few additional MMIO accesses.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reported-by: Nianyao Tang <tangnianyao@huawei.com>
Tested-by: Nianyao Tang <tangnianyao@huawei.com>
Link: https://lore.kernel.org/r/1584089195-63897-1-git-send-email-zhangshaokun@hisilicon.com
|
|
Per the spec, the BCM2835's IRQs are all disabled when coming out of
power-on reset. Its IRQ driver assumes that's still the case when the
kernel boots and does not perform any initialization of the registers.
However the Raspberry Pi Foundation's bootloader leaves the USB
interrupt enabled when handing over control to the kernel.
Quiesce IRQs and the FIQ if they were left enabled and log a message to
let users know that they should update the bootloader once a fixed
version is released.
If the USB interrupt is not quiesced and the USB driver later on claims
the FIQ (as it does on the Raspberry Pi Foundation's downstream kernel),
interrupt latency for all other peripherals increases and occasional
lockups occur. That's because both the FIQ and the normal USB interrupt
fire simultaneously:
On a multicore Raspberry Pi, if normal interrupts are routed to CPU 0
and the FIQ to CPU 1 (hardcoded in the Foundation's kernel), then a USB
interrupt causes CPU 0 to spin in bcm2836_chained_handle_irq() until the
FIQ on CPU 1 has cleared it. Other peripherals' interrupts are starved
as long. I've seen CPU 0 blocked for up to 2.9 msec. eMMC throughput
on a Compute Module 3 irregularly dips to 23.0 MB/s without this commit
but remains relatively constant at 23.5 MB/s with this commit.
The lockups occur when CPU 0 receives a USB interrupt while holding a
lock which CPU 1 is trying to acquire while the FIQ is temporarily
disabled on CPU 1. At best users get RCU CPU stall warnings, but most
of the time the system just freezes.
Fixes: 89214f009c1d ("ARM: bcm2835: add interrupt controller driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/f97868ba4e9b86ddad71f44ec9d8b3b7d8daa1ea.1582618537.git.lukas@wunner.de
|
|
Current, PLIC driver can support only 1 PLIC on the board. However,
there can be multiple PLICs present on a two socket systems in RISC-V.
Modify the driver so that each PLIC handler can have a information
about individual PLIC registers and an irqdomain associated with it.
Tested on two socket RISC-V system based on VCU118 FPGA connected via
OmniXtend protocol.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20200302231146.15530-3-atish.patra@wdc.com
|
|
Currently, PLIC threshold is only initialized once in the beginning.
However, threshold can be set to disabled if a CPU is marked offline with
CPU hotplug feature. This will not allow to change the irq affinity to a
CPU that just came online.
Add PLIC specific CPU hotplug callbacks and enable the threshold when a CPU
comes online. Take this opportunity to move the external interrupt enable
code from trap init to PLIC driver as well. On cpu offline path, the driver
performs the exact opposite operations i.e. disable the interrupt and
the threshold.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20200302231146.15530-2-atish.patra@wdc.com
|
|
Zephyr secondary cache is 256KB, 128B lines. 32B sectors. A secondary cache
line can contain two instruction cache lines (64B), or four data cache
lines (32B). Hardware prefetch Cache detects stream access, and prefetches
ahead of processor access. Add support to invalidate BMIPS5000 cpu zephyr
secondary cache module (ZSCM) on DMA from device so that data returned is
coherent during DMA read operations.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Recently all usages of setup_irq() was replaced by request_irq().
request_irq() does a few sanity checks that were not done in
setup_irq(), if they fail irq registration will fail. One of the check
is to ensure that non-NULL dev_id is passed in the case of shared irq.
This caused malta on qemu to hang.
Fix it by passing handler as dev_id to all request_irq()'s that are
shared. For sni, instead of passing non-NULL dev_id, remove shared irq
flags.
Fixes: ac8fd122e070 ("MIPS: Replace setup_irq() by request_irq()")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Suggested-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
This is done in order to remove the confusion that arises at some places
in the code where local variables or arguments shadow the global variable.
It is already visible that some places are a bit awkward and iterate over
the global variable, for the sole reason that they used to rely on it being
named "fdc" in order to get the correct address when using FD_DOR. These
ones are easy to spot by searching for "for (current_fdc...".
Some more cleanup is definitely possible. For example
"fdc_state[current_fdc].somefield" is used all over the code and would
probably be better with "fdc_state->somefield" with fdc_state being set
when current_fdc is assigned. This would require to pass the pointer to
the current state instead of the current_fdc to the I/O functions.
Link: https://lore.kernel.org/r/20200301195555.11154-7-w@1wt.eu
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
FDC registers FD_STATUS, FD_DATA, FD_DOR, FD_DIR and FD_DCR used to be
defined relative to FD_IOPORT, which is the FDC's base address, itself
a macro depending on the "fdc" local or global variable.
This patch changes this so that the register macros above now only
reference the address offset, and that the FDC's address is explicitly
passed in each call to fd_inb() and fd_outb(), thus removing the macro.
With this change there is no more implicit usage of the local/global
"fdc" variable.
One place in the ARM code used to check if the port was equal to FD_DOR,
this was changed to testing the register by applying a mask to the port,
as was already done in the sparc code.
There are still occurrences of fd_inb() and fd_outb() in the PARISC
code and these ones remain unaffected since they already used to work
with a base address and a register offset.
The sparc, m68k and parisc code could now be slightly cleaned up to
benefit from the macro definitions above instead of the equivalent
hard-coded values.
Link: https://lore.kernel.org/r/20200301195555.11154-6-w@1wt.eu
Cc: Ian Molton <spyro@f2s.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
These two functions replace fd_inb() and fd_outb() in that they take
the FDC in argument. This will ease the separation of the base address
and the port everywhere the code is used.
Link: https://lore.kernel.org/r/20200301195555.11154-5-w@1wt.eu
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The fd_outb() macro on ARM relies on a special fd_setdor() macro when
the register is FD_DOR and both will need to be changed to accept a
separate base address. Let's just remerge them to simplify the change
and make this code more easily reviewable.
Link: https://lore.kernel.org/r/20200301195555.11154-4-w@1wt.eu
Cc: Ian Molton <spyro@f2s.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The ARM code was written with the apparent hope to one day support
a second FDC except that the code was incomplete and only touches
the first one, which is also reflected by N_FDC==1. However this
made its fd_outb() macro artificially depend on the global or local
"fdc" variable.
Let's get rid of this and make it explicit it doesn't rely on this
variable anymore.
Link: https://lore.kernel.org/r/20200301195555.11154-3-w@1wt.eu
Cc: Ian Molton <spyro@f2s.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
On ARM, function fd_scandrives pre-dates Git era, is #ifed 0 out, not
used, and cannot even compile since it references an fdc variable that's
not declared anywhere (supposed to be the global one that we're turning
to current_fdc apparently).
There was also an ifdefde out include of mach/floppy.h that does not
exist anymore either. Let's get rid of them since they complicate the
fixing of the driver.
Link: https://lore.kernel.org/r/20200301195555.11154-2-w@1wt.eu
Cc: Ian Molton <spyro@f2s.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Several macros were used to access reply_buffer[] at discrete positions
without making it obvious they were relying on this. These ones have
been replaced by their offset in the reply buffer to make these accesses
more obvious.
Link: https://lore.kernel.org/r/20200224212352.8640-11-w@1wt.eu
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
