| Age | Commit message (Collapse) | Author |
|---|
|
xgbe_get_link_ksettings() does not propagate correct speed and duplex
information to ethtool during cable unplug. Due to which ethtool reports
incorrect values for speed and duplex.
Address this by propagating correct information.
Fixes: 7c12aa08779c ("amd-xgbe: Move the PHY support into amd-xgbe")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The existing implementation uses software logic to accumulate tx
completions until the specified time (1ms) is met and then poll them.
However, there exists a tiny gap which leads to a race between
resetting and checking the tx_activate flag. Due to this the tx
completions are not reported to upper layer and tx queue timeout
kicks-in restarting the device.
To address this, introduce a tx cleanup mechanism as part of the
periodic maintenance process.
Fixes: c5aa9e3b8156 ("amd-xgbe: Initial AMD 10GbE platform driver")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Force the mode change for SFI in Fixed PHY configurations. Fixed PHY
configurations needs PLL to be enabled while doing mode set. When the
SFP module isn't connected during boot, driver assumes AN is ON and
attempts auto-negotiation. However, if the connected SFP comes up in
Fixed PHY configuration the link will not come up as PLL isn't enabled
while the initial mode set command is issued. So, force the mode change
for SFI in Fixed PHY configuration to fix link issues.
Fixes: e57f7a3feaef ("amd-xgbe: Prepare for working with more than one type of phy")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Fix a possible misalignment between page_pool stats and tx xdp_stats
reported in veth_get_ethtool_stats routine.
The issue can be reproduced configuring the veth pair with the
following tx/rx queues:
$ip link add v0 numtxqueues 2 numrxqueues 4 type veth peer name v1 \
numtxqueues 1 numrxqueues 1
and loading a simple XDP program on v0 that just returns XDP_PASS.
In this case on v0 the page_pool stats overwrites tx xdp_stats for queue 1.
Fix the issue incrementing pp_idx of dev->real_num_tx_queues * VETH_TQ_STATS_LEN
since we always report xdp_stats for all tx queues in ethtool.
Fixes: 4fc418053ec7 ("net: veth: add page_pool stats")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/c5b5d0485016836448453f12846c7c4ab75b094a.1700593593.git.lorenzo@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
queue than its PF
It is possible to add a ntuple rule which would like to direct packet to
a VF whose number of queues are greater/less than its PF's queue numbers.
For example a PF can have 2 Rx queues but a VF created on that PF can have
8 Rx queues. As of today, ntuple rule will reject rule because it is
checking the requested queue number against PF's number of Rx queues.
As a part of this fix if the action of a ntuple rule is to move a packet
to a VF's queue then the check is removed. Also, a debug information is
printed to aware user that it is user's responsibility to cross check if
the requested queue number on that VF is a valid one.
Fixes: f0a1913f8a6f ("octeontx2-pf: Add support for ethtool ntuple filters")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20231121165624.3664182-1-sumang@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Interface 4 is used by for QMI interface in stock firmware of MF28D, the
router which uses MF290 modem. Rebind it to qmi_wwan after freeing it up
from option driver.
The proper configuration is:
Interface mapping is:
0: QCDM, 1: (unknown), 2: AT (PCUI), 2: AT (Modem), 4: QMI
T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=19d2 ProdID=0189 Rev= 0.00
S: Manufacturer=ZTE, Incorporated
S: Product=ZTE LTE Technologies MSM
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=86(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://lore.kernel.org/r/20231117231918.100278-3-lech.perczak@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When CONFIG_NVME_KEYRING is enabled as a loadable module, but the TCP
host code is built-in, it fails to link:
arm-linux-gnueabi-ld: drivers/nvme/host/tcp.o: in function `nvme_tcp_setup_ctrl':
tcp.c:(.text+0x1940): undefined reference to `nvme_tls_psk_default'
The problem is that the compile-time conditionals are inconsistent here,
using a mix of #ifdef CONFIG_NVME_TCP_TLS, IS_ENABLED(CONFIG_NVME_TCP_TLS)
and IS_ENABLED(CONFIG_NVME_KEYRING) checks, with CONFIG_NVME_KEYRING
controlling whether the implementation is actually built.
Change it to use IS_ENABLED(CONFIG_NVME_KEYRING) checks consistently,
which should help readability and make it less error-prone. Combining
it with the check for the ctrl->opts->tls flag lets the compiler drop
all the TLS code in configurations without this feature, which also
helps runtime behavior in addition to avoiding the link failure.
To make it possible for the compiler to build the dead code, both
the tls_handshake_timeout variable and the TLS specific members
of nvme_tcp_queue need to be moved out of the #ifdef block as well,
but at least the former of these gets optimized out again.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20231122224719.4042108-4-arnd@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When the NVME target code is built-in but its TCP frontend is a loadable
module, enabling keyring support causes a link failure:
x86_64-linux-ld: vmlinux.o: in function `nvmet_ports_make':
configfs.c:(.text+0x100a211): undefined reference to `nvme_keyring_id'
The problem is that CONFIG_NVME_TARGET_TCP_TLS is a 'bool' symbol that
depends on the tristate CONFIG_NVME_TARGET_TCP, so any 'select' from
it inherits the state of the tristate symbol rather than the intended
CONFIG_NVME_TARGET one that contains the actual call.
The same thing is true for CONFIG_KEYS, which itself is required for
NVME_KEYRING.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20231122224719.4042108-3-arnd@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In configurations without CONFIG_NVME_TARGET_TCP_TLS, the keyring
code might not be available, or using it will result in a runtime
failure:
x86_64-linux-ld: vmlinux.o: in function `nvmet_ports_make':
configfs.c:(.text+0x100a211): undefined reference to `nvme_keyring_id'
Add a check to ensure we only check the keyring if there is a chance
of it being used, which avoids both the runtime and link-time
problems.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20231122224719.4042108-2-arnd@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai Chen:
"Fix several build errors, a potential kernel panic, a cpu hotplug
issue and update links in documentations"
* tag 'loongarch-fixes-6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
Docs/zh_CN/LoongArch: Update links in LoongArch introduction.rst
Docs/LoongArch: Update links in LoongArch introduction.rst
LoongArch: Implement constant timer shutdown interface
LoongArch: Mark {dmw,tlb}_virt_to_page() exports as non-GPL
LoongArch: Silence the boot warning about 'nokaslr'
LoongArch: Add __percpu annotation for __percpu_read()/__percpu_write()
LoongArch: Record pc instead of offset in la_abs relocation
LoongArch: Explicitly set -fdirect-access-external-data for vmlinux
LoongArch: Add dependency between vmlinuz.efi and vmlinux.efi
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fixes from Wei Liu:
- One fix for the KVP daemon (Ani Sinha)
- Fix for the detection of E820_TYPE_PRAM in a Gen2 VM (Saurabh Sengar)
- Micro-optimization for hv_nmi_unknown() (Uros Bizjak)
* tag 'hyperv-fixes-signed-20231121' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
x86/hyperv: Use atomic_try_cmpxchg() to micro-optimize hv_nmi_unknown()
x86/hyperv: Fix the detection of E820_TYPE_PRAM in a Gen2 VM
hv/hv_kvp_daemon: Some small fixes for handling NM keyfiles
|
|
We really don't want to do atomic_read() or anything like that, since we
already have the value, not the lock. The whole point of this is that
we've loaded the lock from memory, and we want to check whether the
value we loaded was a locked one or not.
The main use of this is the lockref code, which loads both the lock and
the reference count in one atomic operation, and then works on that
combined value. With the atomic_read(), the compiler would pointlessly
spill the value to the stack, in order to then be able to read it back
"atomically".
This is the qspinlock version of commit c6f4a9002252 ("asm-generic:
ticket-lock: Optimize arch_spin_value_unlocked()") which fixed this same
bug for ticket locks.
Cc: Guo Ren <guoren@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Waiman Long <longman@redhat.com>
Link: https://lore.kernel.org/all/CAHk-=whNRv0v6kQiV5QO6DJhjH4KEL36vWQ6Re8Csrnh4zbRkQ@mail.gmail.com/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull NVMe fixes from Keith:
"nvme fixes for Linux 6.7
- TCP TLS fixes (Hannes)
- Authentifaction fixes (Mark, Hannes)
- Properly terminate target names (Christoph)"
* tag 'nvme-6.7-2023-11-22' of git://git.infradead.org/nvme:
nvme: move nvme_stop_keep_alive() back to original position
nvmet-tcp: always initialize tls_handshake_tmo_work
nvmet: nul-terminate the NQNs passed in the connect command
nvme: blank out authentication fabrics options if not configured
nvme: catch errors from nvme_configure_metadata()
nvme-tcp: only evaluate 'tls' option if TLS is selected
nvme-auth: set explanation code for failure2 msgs
nvme-auth: unlock mutex in one place only
|
|
Stopping keep-alive not only stops the keep-alive workqueue,
but also needs to be synchronized with I/O termination as we
must not send a keep-alive command after all I/O had been
terminated.
So to avoid any regressions move the call to stop_keep_alive()
back to its original position and ensure that keep-alive is
correctly stopped failing to setup the admin queue.
Fixes: 4733b65d82bd ("nvme: start keep-alive after admin queue setup")
Suggested-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
This reverts commit efa5f1311c4998e9e6317c52bc5ee93b3a0f36df.
I couldn't reproduce the reported issue. What I did, based on a pcap
packet log provided by the reporter:
- Used same chip version (RTL8168h)
- Set MAC address to the one used on the reporters system
- Replayed the EAPOL unicast packet that, according to the reporter,
was filtered out by the mc filter.
The packet was properly received.
Therefore the root cause of the reported issue seems to be somewhere
else. Disabling mc filtering completely for the most common chip
version is a quite big hammer. Therefore revert the change and wait
for further analysis results from the reporter.
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We found a data corruption issue during testing of SMC-R on Redis
applications.
The benchmark has a low probability of reporting a strange error as
shown below.
"Error: Protocol error, got "\xe2" as reply type byte"
Finally, we found that the retrieved error data was as follows:
0xE2 0xD4 0xC3 0xD9 0x04 0x00 0x2C 0x20 0xA6 0x56 0x00 0x16 0x3E 0x0C
0xCB 0x04 0x02 0x01 0x00 0x00 0x20 0x00 0x00 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xE2
It is quite obvious that this is a SMC DECLINE message, which means that
the applications received SMC protocol message.
We found that this was caused by the following situations:
client server
¦ clc proposal
------------->
¦ clc accept
<-------------
¦ clc confirm
------------->
wait llc confirm
send llc confirm
¦failed llc confirm
¦ x------
(after 2s)timeout
wait llc confirm rsp
wait decline
(after 1s) timeout
(after 2s) timeout
¦ decline
-------------->
¦ decline
<--------------
As a result, a decline message was sent in the implementation, and this
message was read from TCP by the already-fallback connection.
This patch double the client timeout as 2x of the server value,
With this simple change, the Decline messages should never cross or
collide (during Confirm link timeout).
This issue requires an immediate solution, since the protocol updates
involve a more long-term solution.
Fixes: 0fb0b02bd6fd ("net/smc: adapt SMC client code to use the LLC flow")
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot reported an memory leak that happens when an skb is add to
send_buff after virtual nci closed.
This patch adds a variable to track if the ndev is running before
handling new skb in send function.
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Reported-by: syzbot+6eb09d75211863f15e3e@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/lkml/00000000000075472b06007df4fb@google.com
Reviewed-by: Bongsu Jeon
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Honor MagicBook 13 2023 has a touchpad which do not switch to the multitouch
mode until the input mode feature is written by the host. The touchpad do
report the input mode at touchpad(3), while itself working under mouse mode. As
a workaround, it is possible to call MT_QUIRE_FORCE_GET_FEATURE to force set
feature in mt_set_input_mode for such device.
The touchpad reports as BLTP7853, which cannot retrive any useful manufacture
information on the internel by this string at present. As the serial number of
the laptop is GLO-G52, while DMI info reports the laptop serial number as
GLO-GXXX, this workaround should applied to all models which has the GLO-GXXX.
Signed-off-by: Aoba K <nexp_0x17@outlook.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Some devices managed by this driver automatically set brightness to 0
before entering a suspended state and reset it back to a default
brightness level after the resume:
this has the effect of having the kernel report wrong brightness
status after a sleep, and on some devices (like the Asus RC71L) that
brightness is the intensity of LEDs directly facing the user.
Fix the above issue by setting back brightness to the level it had
before entering a sleep state.
Signed-off-by: Denis Benato <benato.denis96@gmail.com>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
In the function asus_kbd_set_report the parameter buf is read-only
as it gets copied in a memory portion suitable for USB transfer,
but the parameter is not marked as const: add the missing const and mark
const immutable buffers passed to that function.
Signed-off-by: Denis Benato <benato.denis96@gmail.com>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Use atomic_try_cmpxchg() instead of atomic_cmpxchg(*ptr, old, new) == old
in hv_nmi_unknown(). On x86 the CMPXCHG instruction returns success in
the ZF flag, so this change saves a compare after CMPXCHG. The generated
asm code improves from:
3e: 65 8b 15 00 00 00 00 mov %gs:0x0(%rip),%edx
45: b8 ff ff ff ff mov $0xffffffff,%eax
4a: f0 0f b1 15 00 00 00 lock cmpxchg %edx,0x0(%rip)
51: 00
52: 83 f8 ff cmp $0xffffffff,%eax
55: 0f 95 c0 setne %al
to:
3e: 65 8b 15 00 00 00 00 mov %gs:0x0(%rip),%edx
45: b8 ff ff ff ff mov $0xffffffff,%eax
4a: f0 0f b1 15 00 00 00 lock cmpxchg %edx,0x0(%rip)
51: 00
52: 0f 95 c0 setne %al
No functional change intended.
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20231114170038.381634-1-ubizjak@gmail.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20231114170038.381634-1-ubizjak@gmail.com>
|
|
We should clean the skb resource if genlmsg_put_reply failed.
Fixes: 9d71b54b65b1 ("dpll: netlink: Add DPLL framework base functions")
Signed-off-by: Hao Ge <gehao@kylinos.cn>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://lore.kernel.org/r/20231121013709.73323-1-gehao@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2023-11-21
We've added 19 non-merge commits during the last 4 day(s) which contain
a total of 18 files changed, 1043 insertions(+), 416 deletions(-).
The main changes are:
1) Fix BPF verifier to validate callbacks as if they are called an unknown
number of times in order to fix not detecting some unsafe programs,
from Eduard Zingerman.
2) Fix bpf_redirect_peer() handling which missed proper stats accounting
for veth and netkit and also generally fix missing stats for the latter,
from Peilin Ye, Daniel Borkmann et al.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: check if max number of bpf_loop iterations is tracked
bpf: keep track of max number of bpf_loop callback iterations
selftests/bpf: test widening for iterating callbacks
bpf: widening for callback iterators
selftests/bpf: tests for iterating callbacks
bpf: verify callbacks as if they are called unknown number of times
bpf: extract setup_func_entry() utility function
bpf: extract __check_reg_arg() utility function
selftests/bpf: fix bpf_loop_bench for new callback verification scheme
selftests/bpf: track string payload offset as scalar in strobemeta
selftests/bpf: track tcp payload offset as scalar in xdp_synproxy
selftests/bpf: Add netkit to tc_redirect selftest
selftests/bpf: De-veth-ize the tc_redirect test case
bpf, netkit: Add indirect call wrapper for fetching peer dev
bpf: Fix dev's rx stats for bpf_redirect_peer traffic
veth: Use tstats per-CPU traffic counters
netkit: Add tstats per-CPU traffic counters
net: Move {l,t,d}stats allocation to core and convert veth & vrf
net, vrf: Move dstats structure to core
====================
Link: https://lore.kernel.org/r/20231121193113.11796-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There has been more than a few threads which went idle before
the merge window and now people came back to them and started
asking about next steps.
We currently tell people to be patient and not to repost too
often. Our "not too often", however, is still a few orders of
magnitude faster than other subsystems. Or so I feel after
hearing people talk about review rates at LPC.
Clarify in the doc that if the discussion went idle for a week
on netdev, 95% of the time there's no point waiting longer.
Link: https://lore.kernel.org/r/20231120200109.620392-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Using generic ASIX Electronics Corp. AX88179 Gigabit Ethernet device,
the following test cycle has been implemented:
- power on
- check logs
- shutdown
- after detecting the system shutdown, disconnect power
- after approximately 60 seconds of sleep, power is restored
Running some cycles, sometimes error logs like this appear:
kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to write reg index 0x0001: -19
kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to read reg index 0x0001: -19
...
These failed operation are happening during ax88179_reset execution, so
the initialization could not be correct.
In order to avoid this, we need to increase the delay after reset and
clock initial operations. By using these larger values, many cycles
have been run and no failed operations appear.
It would be better to check some status register to verify when the
operation has finished, but I do not have found any available information
(neither in the public datasheets nor in the manufacturer's driver). The
only available information for the necessary delays is the maufacturer's
driver (original values) but the proposed values are not enough for the
tested devices.
Fixes: e2ca90c276e1f ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Reported-by: Herb Wei <weihao.bj@ieisystem.com>
Tested-by: Herb Wei <weihao.bj@ieisystem.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://lore.kernel.org/r/20231120120642.54334-1-jtornosm@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This probably isn't the ideal fix, but we ended up using chids
sparsely, and lots of things rely on indexing into the full range,
so just allocate the full range up front.
The GSP code fixes 8 channels into a userd page, but we end up using
a single userd page per channel so end up sparsely using the range.
Fixes a few crashes seen with multiple channels.
Link: https://gitlab.freedesktop.org/drm/nouveau/-/issues/277
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231121201109.2988516-1-airlied@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform drivers fixes from Ilpo Järvinen:
"Just a few fixes (one with two non-fix deps) plus tidying up
MAINTAINERS"
* tag 'platform-drivers-x86-v6.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: intel_telemetry: Fix kernel doc descriptions
MAINTAINERS: Drop Mark Gross as maintainer for x86 platform drivers
platform/x86/amd/pmc: adjust getting DRAM size behavior
platform/x86: hp-bioscfg: Remove unused obj in hp_add_other_attributes()
platform/x86: hp-bioscfg: Fix error handling in hp_add_other_attributes()
platform/x86: hp-bioscfg: move mutex_lock() down in hp_add_other_attributes()
platform/x86: hp-bioscfg: Simplify return check in hp_add_other_attributes()
platform/x86: ideapad-laptop: Set max_brightness before using it
MAINTAINERS: Remove stale entry for SBL platform driver
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull erofs fixes from Gao Xiang:
- Tidy up erofs_read_inode() for simplicity
- Fix broken fscache mode due to NULL dereference of dif->bdev_handle
- Add the EROFS webpage to MAINTAINERS, documentation, and Kconfig
* tag 'erofs-for-6.7-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
MAINTAINERS: erofs: add EROFS webpage
erofs: fix NULL dereference of dif->bdev_handle in fscache mode
erofs: simplify erofs_read_inode()
|
|
The refresh reported by modetest is 60.46Hz, and the actual measurement
is 60.01Hz, which is outside the expected tolerance. Adjust hporch and
pixel clock to fix it. After repair, modetest and actual measurement were
all 60.01Hz.
Modetest refresh = Pixel CLK/ htotal* vtotal, but measurement frame rate
is HS->LP cycle time(Vblanking). Measured frame rate is not only affecte
by Htotal/Vtotal/pixel clock, also affected by Lane-num/PixelBit/LineTime
/DSI CLK. Assume that the DSI controller could not make the mode that we
requested(presumably it's PLL couldn't generate the exact pixel clock?).
If you use a different DSI controller, you may need to readjust these
parameters. Now this panel looks like it's only used by me on the MTK
platform, so let's change this set of parameters.
Fixes: 1bc2ef065f13 ("drm/panel: Support for Starry-himax83102-j02 TDDI MIPI-DSI panel")
Signed-off-by: Cong Yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231120020109.3216343-1-yangcong5@huaqin.corp-partner.google.com
|
|
If a socket is processing ioctl 'NBD_SET_SOCK', config->socks might be
krealloc in nbd_add_socket(), and a garbage request is received now, a UAF
may occurs.
T1
nbd_ioctl
__nbd_ioctl
nbd_add_socket
blk_mq_freeze_queue
T2
recv_work
nbd_read_reply
sock_xmit
krealloc config->socks
def config->socks
Pass nbd_sock to nbd_read_reply(). And introduce a new function
sock_xmit_recv(), which differs from sock_xmit only in the way it get
socket.
==================================================================
BUG: KASAN: use-after-free in sock_xmit+0x525/0x550
Read of size 8 at addr ffff8880188ec428 by task kworker/u12:1/18779
Workqueue: knbd4-recv recv_work
Call Trace:
__dump_stack
dump_stack+0xbe/0xfd
print_address_description.constprop.0+0x19/0x170
__kasan_report.cold+0x6c/0x84
kasan_report+0x3a/0x50
sock_xmit+0x525/0x550
nbd_read_reply+0xfe/0x2c0
recv_work+0x1c2/0x750
process_one_work+0x6b6/0xf10
worker_thread+0xdd/0xd80
kthread+0x30a/0x410
ret_from_fork+0x22/0x30
Allocated by task 18784:
kasan_save_stack+0x1b/0x40
kasan_set_track
set_alloc_info
__kasan_kmalloc
__kasan_kmalloc.constprop.0+0xf0/0x130
slab_post_alloc_hook
slab_alloc_node
slab_alloc
__kmalloc_track_caller+0x157/0x550
__do_krealloc
krealloc+0x37/0xb0
nbd_add_socket
+0x2d3/0x880
__nbd_ioctl
nbd_ioctl+0x584/0x8e0
__blkdev_driver_ioctl
blkdev_ioctl+0x2a0/0x6e0
block_ioctl+0xee/0x130
vfs_ioctl
__do_sys_ioctl
__se_sys_ioctl+0x138/0x190
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x61/0xc6
Freed by task 18784:
kasan_save_stack+0x1b/0x40
kasan_set_track+0x1c/0x30
kasan_set_free_info+0x20/0x40
__kasan_slab_free.part.0+0x13f/0x1b0
slab_free_hook
slab_free_freelist_hook
slab_free
kfree+0xcb/0x6c0
krealloc+0x56/0xb0
nbd_add_socket+0x2d3/0x880
__nbd_ioctl
nbd_ioctl+0x584/0x8e0
__blkdev_driver_ioctl
blkdev_ioctl+0x2a0/0x6e0
block_ioctl+0xee/0x130
vfs_ioctl
__do_sys_ioctl
__se_sys_ioctl+0x138/0x190
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x61/0xc6
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230911023308.3467802-1-linan666@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
indirect_call_wrapper.h is not, strictly speaking, networking specific.
However, it's git history indicates that in practice changes go through
netdev and thus the netdev maintainers have effectively been taking
responsibility for it.
Formalise this by adding it to the NETWORKING [GENERAL] section in the
MAINTAINERS file.
It is not clear how many other files under include/linux fall into this
category and it would be interesting, as a follow-up, to audit that and
propose further updates to the MAINTAINERS file as appropriate.
Link: https://lore.kernel.org/netdev/20231116010310.4664dd38@kernel.org/
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20231120-indirect_call_wrapper-maintainer-v1-1-0a6bb1f7363e@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This reverts commit 9d1bd9346241cd6963b58da7ffb7ed303285f684.
Multiple people reported misbehaving devices and reverting this commit fixes
the problem for them. As soon as the original commit author starts reacting
again, we can try to figure out why he hasn't seen the issues (mismatching
report descriptors?), but for the time being, fix for 6.7 by reverting.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218172
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218094
Cc: <stable@vger.kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Haiyang Zhang says:
====================
hv_netvsc: fix race of netvsc, VF register, and slave bit
There are some races between netvsc probe, set notifier, VF register,
and slave bit setting.
This patch set fixes them.
====================
Link: https://lore.kernel.org/r/1700411023-14317-1-git-send-email-haiyangz@microsoft.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When a VF is being exposed form the kernel, it should be marked as "slave"
before exposing to the user-mode. The VF is not usable without netvsc
running as master. The user-mode should never see a VF without the "slave"
flag.
This commit moves the code of setting the slave flag to the time before
VF is exposed to user-mode.
Cc: stable@vger.kernel.org
Fixes: 0c195567a8f6 ("netvsc: transparent VF management")
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If VF NIC is registered earlier, NETDEV_REGISTER event is replayed,
but NETDEV_POST_INIT is not.
Move register_netdevice_notifier() earlier, so the call back
function is set before probing.
Cc: stable@vger.kernel.org
Fixes: e04e7a7bbd4b ("hv_netvsc: Fix a deadlock by getting rtnl lock earlier in netvsc_probe()")
Reported-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The rtnl lock also needs to be held before rndis_filter_device_add()
which advertises nvsp_2_vsc_capability / sriov bit, and triggers
VF NIC offering and registering. If VF NIC finished register_netdev()
earlier it may cause name based config failure.
To fix this issue, move the call to rtnl_lock() before
rndis_filter_device_add(), so VF will be registered later than netvsc
/ synthetic NIC, and gets a name numbered (ethX) after netvsc.
Cc: stable@vger.kernel.org
Fixes: e04e7a7bbd4b ("hv_netvsc: Fix a deadlock by getting rtnl lock earlier in netvsc_probe()")
Reported-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
net/ipv4/route.c:783:46: warning: incorrect type in argument 2 (different base types)
net/ipv4/route.c:783:46: expected unsigned int [usertype] key
net/ipv4/route.c:783:46: got restricted __be32 [usertype] new_gw
Fixes: 969447f226b4 ("ipv4: use new_gw for redirect neigh lookup")
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Link: https://lore.kernel.org/r/20231119141759.420477-1-chentao@kylinos.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
These devices disconnect if suspended without remote wakeup. They can operate
with the standard driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Many user-space compositors fail with mode setting if a CRTC has
more than one connected connector. This is the case with the BMC
on Aspeed systems. Work around this problem by setting the BMC's
connector status to disconnected when the physical connector has
a display attached. This way compositors will only see one connected
connector at a time; either the physical one or the BMC.
Suggested-by: Jocelyn Falempe <jfalempe@redhat.com>
Fixes: e329cb53b45d ("drm/ast: Add BMC virtual connector")
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: <stable@vger.kernel.org> # v6.6+
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231116130217.22931-1-tzimmermann@suse.de
|
|
The Glorious Model I mouse has a buggy HID report descriptor for its
keyboard endpoint (used for programmable buttons). For report ID 2, there
is a mismatch between Logical Minimum and Usage Minimum in the array that
reports keycodes.
The offending portion of the descriptor: (from hid-decode)
0x95, 0x05, // Report Count (5) 30
0x75, 0x08, // Report Size (8) 32
0x15, 0x00, // Logical Minimum (0) 34
0x25, 0x65, // Logical Maximum (101) 36
0x05, 0x07, // Usage Page (Keyboard) 38
0x19, 0x01, // Usage Minimum (1) 40
0x29, 0x65, // Usage Maximum (101) 42
0x81, 0x00, // Input (Data,Arr,Abs) 44
This bug shifts all programmed keycodes up by 1. Importantly, this causes
"empty" array indexes of 0x00 to be interpreted as 0x01, ErrorRollOver.
The presence of ErrorRollOver causes the system to ignore all keypresses
from the endpoint and breaks the ability to use the programmable buttons.
Setting byte 41 to 0x00 fixes this, and causes keycodes to be interpreted
correctly.
Also, USB_VENDOR_ID_GLORIOUS is changed to USB_VENDOR_ID_SINOWEALTH,
and a new ID for Laview Technology is added. Glorious seems to be
white-labeling controller boards or mice from these vendors. There isn't a
single canonical vendor ID for Glorious products.
Signed-off-by: Brett Raye <braye@fastmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
hid_debug_events_release releases resources bound to the HID device instance.
hid_device_release releases the underlying HID device instance potentially
before hid_debug_events_release has completed releasing debug resources bound
to the same HID device instance.
Reference count to prevent the HID device instance from being torn down
preemptively when HID debugging support is used. When count reaches zero,
release core resources of HID device instance using hiddev_free.
The crash:
[ 120.728477][ T4396] kernel BUG at lib/list_debug.c:53!
[ 120.728505][ T4396] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[ 120.739806][ T4396] Modules linked in: bcmdhd dhd_static_buf 8822cu pcie_mhi r8168
[ 120.747386][ T4396] CPU: 1 PID: 4396 Comm: hidt_bridge Not tainted 5.10.110 #257
[ 120.754771][ T4396] Hardware name: Rockchip RK3588 EVB4 LP4 V10 Board (DT)
[ 120.761643][ T4396] pstate: 60400089 (nZCv daIf +PAN -UAO -TCO BTYPE=--)
[ 120.768338][ T4396] pc : __list_del_entry_valid+0x98/0xac
[ 120.773730][ T4396] lr : __list_del_entry_valid+0x98/0xac
[ 120.779120][ T4396] sp : ffffffc01e62bb60
[ 120.783126][ T4396] x29: ffffffc01e62bb60 x28: ffffff818ce3a200
[ 120.789126][ T4396] x27: 0000000000000009 x26: 0000000000980000
[ 120.795126][ T4396] x25: ffffffc012431000 x24: ffffff802c6d4e00
[ 120.801125][ T4396] x23: ffffff8005c66f00 x22: ffffffc01183b5b8
[ 120.807125][ T4396] x21: ffffff819df2f100 x20: 0000000000000000
[ 120.813124][ T4396] x19: ffffff802c3f0700 x18: ffffffc01d2cd058
[ 120.819124][ T4396] x17: 0000000000000000 x16: 0000000000000000
[ 120.825124][ T4396] x15: 0000000000000004 x14: 0000000000003fff
[ 120.831123][ T4396] x13: ffffffc012085588 x12: 0000000000000003
[ 120.837123][ T4396] x11: 00000000ffffbfff x10: 0000000000000003
[ 120.843123][ T4396] x9 : 455103d46b329300 x8 : 455103d46b329300
[ 120.849124][ T4396] x7 : 74707572726f6320 x6 : ffffffc0124b8cb5
[ 120.855124][ T4396] x5 : ffffffffffffffff x4 : 0000000000000000
[ 120.861123][ T4396] x3 : ffffffc011cf4f90 x2 : ffffff81fee7b948
[ 120.867122][ T4396] x1 : ffffffc011cf4f90 x0 : 0000000000000054
[ 120.873122][ T4396] Call trace:
[ 120.876259][ T4396] __list_del_entry_valid+0x98/0xac
[ 120.881304][ T4396] hid_debug_events_release+0x48/0x12c
[ 120.886617][ T4396] full_proxy_release+0x50/0xbc
[ 120.891323][ T4396] __fput+0xdc/0x238
[ 120.895075][ T4396] ____fput+0x14/0x24
[ 120.898911][ T4396] task_work_run+0x90/0x148
[ 120.903268][ T4396] do_exit+0x1bc/0x8a4
[ 120.907193][ T4396] do_group_exit+0x8c/0xa4
[ 120.911458][ T4396] get_signal+0x468/0x744
[ 120.915643][ T4396] do_signal+0x84/0x280
[ 120.919650][ T4396] do_notify_resume+0xd0/0x218
[ 120.924262][ T4396] work_pending+0xc/0x3f0
[ Rahul Rameshbabu <sergeantsagara@protonmail.com>: rework changelog ]
Fixes: cd667ce24796 ("HID: use debugfs for events/reports dumping")
Signed-off-by: Charles Yi <be286@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Jamesdonkey A3R keyboard is identified as "Jamesdonkey A3R" in wired
mode, "A3R-U" in wireless mode and "A3R" in bluetooth mode. Adding them
to non-apple keyboards fixes function key.
Signed-off-by: Yihong Cao <caoyihong4@outlook.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
During the probe we add an I2C adapter and as soon as we add that adapter
it may be used for a transfer (e.g via the code in i2cdetect()).
Those transfers are not able to complete and time out. This is because the
HID raw_event callback (mcp2221_raw_event) will not be invoked until the
HID device's 'driver_input_lock' is marked up at the completion of the
probe in hid_device_probe(). This starves the driver of the responses it
is waiting for.
In order to allow the I2C transfers to complete while we are still in the
probe, start the IO once we have completed init of the HID device.
This issue seems to have been seen before and a patch was submitted but
it seems it was never accepted. See:
https://lore.kernel.org/all/20221103222714.21566-3-Enrik.Berkhan@inka.de/
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The process of adding an I2C adapter can invoke I2C accesses on that new
adapter (see i2c_detect()).
Ensure we have set the adapter's driver data to avoid null pointer
dereferences in the xfer functions during the adapter add.
This has been noted in the past and the same fix proposed but not
completed. See:
https://lore.kernel.org/lkml/ef597e73-ed71-168e-52af-0d19b03734ac@vigem.de/
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
There is no need to call MMIO reset using VPU_37XX_BUTTRESS_VPU_IP_RESET
register. IP will be reset by FLR or by entering d0i3. Also IP reset
during power_up is not needed as the VPU is already in reset.
Removing MMIO reset improves stability as it a partial device reset
that is not safe in some corner cases.
This change also brings back ivpu_boot_pwr_domain_disable() that
helps to properly power down VPU when it is hung by a buggy workload.
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Fixes: 828d63042aec ("accel/ivpu: Don't enter d0i3 during FLR")
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231115111004.1304092-1-jacek.lawrynowicz@linux.intel.com
|
|
LKP found issues with a kernel doc in the driver:
core.c:116: warning: Function parameter or member 'ioss_evtconfig' not described in 'telemetry_update_events'
core.c:188: warning: Function parameter or member 'ioss_evtconfig' not described in 'telemetry_get_eventconfig'
It looks like it were copy'n'paste typos when these descriptions
had been introduced. Fix the typos.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310070743.WALmRGSY-lkp@intel.com/
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231120150756.1661425-1-andriy.shevchenko@linux.intel.com
Reviewed-by: Rajneesh Bhardwaj <irenic.rajneesh@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Mark has not really been active as maintainer for x86 platform drivers
lately, drop Mark from the MAINTAINERS entries for drivers/platform/x86,
drivers/platform/mellanox and drivers/platform/surface.
Cc: Mark Gross <markgross@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20231120154548.611041-1-hdegoede@redhat.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
LoongArch-Vol1 has been updated to v1.10, the links in the documentation
are out of date, let's update it.
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
LoongArch-Vol1 has been updated to v1.10, the links in the documentation
are out of date, let's update it.
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
When a cpu is hot-unplugged, it is put in idle state and the function
arch_cpu_idle_dead() is called. The timer interrupt for this processor
should be disabled, otherwise there will be pending timer interrupt for
the unplugged cpu, so that vcpu is prevented from giving up scheduling
when system is running in vm mode.
This patch implements the timer shutdown interface so that the constant
timer will be properly disabled when a CPU is hot-unplugged.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
