| Age | Commit message (Collapse) | Author |
|---|
|
Although we do not yet enable multiple PFs per port, it is possible
that a board will be reconfigured to enable them while the driver has
not yet been updated to fully support this.
The most obvious problem is that multiple functions may try to set
conflicting link settings. But we will also run into trouble if the
firmware doesn't consider us fully trusted. So, abort probing unless
both the LinkCtrl and Trusted flags are set for this function.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
The merge b35c8097 seems to have lost commit eabc4ac5d,
put the code back.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Otherwise, if queues are full during a scan, tx scheduling does not
resume after switching back to the home channel.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
|
|
Sparse points out three places where variables are shadowed,
rename two of the variables and remove the duplicate third.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The (inner) MTU of a ipip6 (IPv4-in-IPv6) tunnel cannot be set below 1280, which is the minimum MTU in IPv6.
However, there should be no IPv6 on the tunnel interface at all, so the IPv6 rules should not apply.
More info at https://bugzilla.kernel.org/show_bug.cgi?id=15530
This patch allows to check the minimum MTU for ipv6 tunnel according to these rules:
-In case the tunnel is configured with ipip6 mode the minimum MTU is 68.
-In case the tunnel is configured with ip6ip6 or any mode the minimum MTU is 1280.
Signed-off-by: Oussama Ghorbel <ou.ghorbel@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- fix for hidraw reference counting regression, by Manoj Chourasia
- fix for minor number allocation for uhid, by David Herrmann
- other small unsorted fixes / device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wiimote: fix FF deadlock
HID: add Holtek USB ID 04d9:a081 SHARKOON DarkGlider
HID: hidraw: close underlying device at removal of last reader
HID: roccat: Fix "cannot create duplicate filename" problems
HID: uhid: allocate static minor
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
Pull Tile bugfixes from Chris Metcalf:
"This fixes some serious issues with PREEMPT support, and a couple of
smaller corner-case issues fixed in the last couple of weeks"
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch: tile: re-use kbasename() helper
tile: use a more conservative __my_cpu_offset in CONFIG_PREEMPT
tile: ensure interrupts disabled for preempt_schedule_irq()
tile: change lock initalization in hardwall
tile: include: asm: use 'long long' instead of 'u64' for atomic64_t and its related functions
|
|
virtio wants to pass in cpumask_of(cpu), make parameter
const to avoid build warnings.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The input core has an internal spinlock that is acquired during event
injection via input_event() and friends but also held during FF callbacks.
That means, there is no way to share a lock between event-injection and FF
handling. Unfortunately, this is what is required for wiimote state
tracking and what we do with state.lock and input->lock.
This deadlock can be triggered when using continuous data reporting and FF
on a wiimote device at the same time. I takes me at least 30m of
stress-testing to trigger it but users reported considerably shorter
times (http://bpaste.net/show/132504/) when using some gaming-console
emulators.
The real problem is that we have two copies of internal state, one in the
wiimote objects and the other in the input device. As the input-lock is
not supposed to be accessed from outside of input-core, we have no other
chance than offloading FF handling into a worker. This actually works
pretty nice and also allows to implictly merge fast rumble changes into a
single request.
Due to the 3-layered workers (rumble+queue+l2cap) this might reduce FF
responsiveness. Initial tests were fine so lets fix the race first and if
it turns out to be too slow we can always handle FF out-of-band and skip
the queue-worker.
Cc: <stable@vger.kernel.org> # 3.11+
Reported-by: Thomas Schneider
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
authentication methods
This allows users to use LANMAN authentication on servers which support
unencapsulated authentication.
The patch fixes a regression where users using plaintext authentication
were no longer able to do so because of changed bought in by patch
3f618223dc0bdcbc8d510350e78ee2195ff93768
https://bugzilla.redhat.com/show_bug.cgi?id=1011621
Reported-by: Panos Kavalagios <Panagiotis.Kavalagios@eurodyn.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
When connecting to SMB2/3 shares, maximum file size is set to non-LFS maximum in superblock. This is due to cap_large_files bit being different for SMB1 and SMB2/3 (where it is just an internal flag that is not negotiated and the SMB1 one corresponds to multichannel capability, so maybe LFS works correctly if server sends 0x08 flag) while capabilities are checked always for the SMB1 bit in cifs_read_super().
The patch fixes this by checking for the correct bit according to the protocol version.
CC: Stable <stable@kernel.org>
Signed-off-by: Jan Klos <honza.klos@gmail.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
When initializing an AMP controller, read its current flow control
mode so that the correct value is used.
The AMP controller defaults to block based flow control and this
extra command is just to double check.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
When initializing an AMP controller, read its current known location
data so that it can be analyzed later on.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Commit 1400eb6 (MIPS: r4k,octeon,r2300: stack protector: change canary
per task) was merged in v3.11 and introduced assembly in the MIPS resume
functions to update the value of the current canary in
__stack_chk_guard. However it used PTR_L resulting in a load of the
canary value, instead of PTR_LA to construct its address. The value is
intended to be random but is then treated as an address in the
subsequent LONG_S (store).
This was observed to cause a fault and panic:
CPU 0 Unable to handle kernel paging request at virtual address 139fea20, epc == 8000cc0c, ra == 8034f2a4
Oops[#1]:
...
$24 : 139fea20 1e1f7cb6
...
Call Trace:
[<8000cc0c>] resume+0xac/0x118
[<8034f2a4>] __schedule+0x5f8/0x78c
[<8034f4e0>] schedule_preempt_disabled+0x20/0x2c
[<80348eec>] rest_init+0x74/0x84
[<804dc990>] start_kernel+0x43c/0x454
Code: 3c18804b 8f184030 8cb901f8 <af190000> 00c0e021 8cb002f0 8cb102f4 8cb202f8 8cb302fc
This can also be forced by modifying
arch/mips/include/asm/stackprotector.h so that the default
__stack_chk_guard value is more likely to be a bad (or unaligned)
pointer.
Fix it to use PTR_LA instead, to load the address of the canary value,
which the LONG_S can then use to write into it.
Reported-by: bobjones (via #mipslinux on IRC)
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/6026/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The commands for reading supported features and commands are both
supported by AMP controllers. Issue them during controller init
phase so their values are known.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The value provided by num_sends_allowed is now
derived from CE source ringbuffer state.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
It is completely pointless to keep this function
around. It doesn't do anything different than
ce_send except it introduces more overhead.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Tidy up ath10k_tx().
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Tidy up ath10k_tx().
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
It was observed few times, the artificial max_scan limit we
are using mainly to detect FW hangs, can be not enough for
instance while being associated and during heavy traffic.
What we do if the FW won't return with scan results within
the max_time time is a scan abort.
This is especially visible with 10.X fw which in combination
with dual band HW (scanning 32 channels) can end up with
hw_scan close to 10 seconds.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Since the WMI API has been added and we can detect from the
FW IEs what firmware variant we deal with, turn on support
for 10.x firmware branch in ath10k_wmi_attach().
kvalo: improve the commit log
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
se_io_cb can be declared static. This fixes the following sparse
warning:
net/nfc/netlink.c:1287:6: warning: symbol 'se_io_cb' was not declared.
Should it be static?
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This implements the target NFC digital operations tg_configure_hw(),
tg_listen(), tg_listen_mdaa(), and tg_send_cmd().
The target mode supports NFC-A technology at 106kbits/s and NFC-F
technologies at 212 and 424kbits/s.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Cc: Stephen Tiedemann <stephen.tiedemann@gmail.com>
Tested-by: Cho, Yu-Chen <acho@suse.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch implements the initiator NFC operations in_configure_hw()
and in_send_cmd(). It also implements the switch_rf() operation.
The initiator mode supports NFC-A technology at 106kbits/s and NFC-F
technologies at 212 and 424kbits/s.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Cc: Stephen Tiedemann <stephen.tiedemann@gmail.com>
Tested-by: Cho, Yu-Chen <acho@suse.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch implements the command handling mechanism. The digital stack
serializes all commands sent to the driver. This means that the digital
stack waits for the reply of the current command before sending a new
one. So there is no command queue managed at driver level.
All Port-100 commands are asynchronous. If the command has been sent
successfully to the device, it replies with an ACK frame. Then the
command response is received (or actually no-response in case of
timeout or error) and a command complete work on the system workqueue
is responsible for sending the response (or the error) back to the
digital stack.
The digital stack requires some commands to be synchronous, mainly
hardware configuration ones. These commands use the asynchronous
command path but are made synchronous by using a completion object.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Cc: Stephen Tiedemann <stephen.tiedemann@gmail.com>
Tested-by: Cho, Yu-Chen <acho@suse.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This adds support for the Sony NFC USB dongle RC-S380, based on the
Port-100 chip. This dongle is an analog frontend and does not implement
the digital layer. This driver uses the nfc_digital module which is an
implementation of the NFC Digital Protocol stack.
This patch is a skeleton. It only registers the dongle against the NFC
digital protocol stack. All NFC digital operation functions are stubbed
out.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Cc: Stephen Tiedemann <stephen.tiedemann@gmail.com>
Tested-by: Cho, Yu-Chen <acho@suse.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
'irq' was not released when clk_prepare_enable failed.
Fix it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The two paths were not connected in the DAPM route causing the associated
routes to be non working and the following warnings printed in the logs:
tlv320aic3x-codec 0-001b: ASoC: mux Right Line1L Mux has no paths
tlv320aic3x-codec 0-001b: ASoC: mux Left Line1R Mux has no paths
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
On imx31 with mc13783 codec the FIQ is not necessary and not enabled
as DMA transfer is available.
Change the probe() function to fail only if both FIQ and DMA are not
available.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
On this machine, DAC on node 0x03 seems to give mono output.
Also, it needs additional patches for headset mic support.
It supports CTIA style headsets only.
Alsa-info available at the bug link below.
Cc: stable@kernel.org (v3.10+)
BugLink: https://bugs.launchpad.net/bugs/1236228
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"A couple of bux fixes, notable are the regression with ptrace vs
restarting system calls and the patch for kdump to be able to copy
from virtual memory"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: fix system call restart after inferior call
s390: Allow vmalloc target buffers for copy_from_oldmem()
s390/sclp: properly detect line mode console
s390/kprobes: add exrl to list of prohibited opcodes
s390/3270: fix return value check in tty3270_resize_work()
|
|
Within the AMP discover response, list powered down AMP controllers
as powered down. No point in trying to make them look any different.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The management interface only operates on BR/EDR controllers. The check
for the power down notification is a bit intermixed with the check if
controller auto power off is active. Since there are more than just
BR/EDR controllers supported, make this check explicit since the auto
power off check also applies to AMP controllers and it has to happen
in this exact order. Otherwise the bit will not be cleared.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Even AMP controllers should be powered off after the setup phase. It
is not a good idea to keep AMP controllers powered on all the time
if they are not in use.
Power on of the AMP controller can either be done manually via
command line commands or directly via A2MP. Especially since there
is an indication in A2MP for powered down controllers that can
be activated.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The return value of mgmt_discovering() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The return value of mgmt_remote_name() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The return value of mgmt_device_found() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The return value of mgmt_device_disconnected() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The return value of mgmt_device_connected() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The return value of mgmt_connect_failed() function is not used
so change it to just return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The return value of mgmt_disconnect_failed() function is not used
so change it to just return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The return value of mgmt_set_powered_failed() function is never used
and so make the function just return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The return value from mgmt_index_added() and mgmt_index_removed()
functions is never used. So do not pretend that returning an error
would actually be handled and just make both functions return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
