| Age | Commit message (Collapse) | Author |
|---|
|
On MT7530, the media-independent interfaces of port 5 and 6 are controlled
by the MT7530_P5_DIS and MT7530_P6_DIS bits of the hardware trap. Deal with
these bits only when the relevant port is being enabled or disabled. This
ensures that these ports will be disabled when they are not in use.
Do not set MT7530_CHG_TRAP on mt7530_setup_port5() as that's already being
done on mt7530_setup().
Instead of globally setting MT7530_P5_MAC_SEL, clear it, then set it only
on the appropriate case.
If PHY muxing is detected, clear MT7530_P5_DIS before calling
mt7530_setup_port5().
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MT7530_HWTRAP and MT7530_MHWTRAP registers are on MT7530 and MT7531.
It's called hardware trap on MT7530, software trap on MT7531. That's
because some bits of the trap on MT7530 cannot be modified by software
whilst all bits of the trap on MT7531 can. Rename the definitions for them
to MT753X_TRAP and MT753X_MTRAP. Add MT7530 and MT7531 prefixes to the
definitions specific to the switch model.
Remove the extra parentheses from MT7530_XTAL_40MHZ and MT7530_XTAL_20MHZ.
Rename MHWTRAP_PHY0_SEL, MHWTRAP_MANUAL, and MHWTRAP_PHY_ACCESS to be on
par with the "MT7621 Giga Switch Programming Guide v0.3" document.
Make an enumaration for the XTAL frequency. Set the data type of the xtal
variable on mt7531_pll_setup() to it.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MT7530_MFC register is on MT7530, MT7531, and the switch on the MT7988
SoC. Rename it to MT753X_MFC. Bit 7 to 0 differs between MT7530 and
MT7531/MT7988. Add MT7530 prefix to these definitions, and define the
IGMP/MLD Query Frame Flooding Ports mask for MT7531.
Rename the cases of MIRROR_MASK to MIRROR_PORT_MASK.
Move mt753x_mirror_port_get() and mt753x_port_mirror_set() to mt7530.h as
macros.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mt753x_bpdu_port_fw enum is globally used for manipulating the process
of deciding the forwardable ports, specifically concerning the CPU port(s).
Therefore, rename it and the values in it to mt753x_to_cpu_fw.
Change FOLLOW_MFC to SYSTEM_DEFAULT to be on par with the switch documents.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The p5_intf_sel pointer is used to store the information of whether PHY
muxing is used or not. PHY muxing is a feature specific to port 5 of the
MT7530 switch. Do not use it for other switch models.
Rename the pointer to p5_mode to store the mode the port is being used in.
Rename the p5_interface_select enum to mt7530_p5_mode, the string
representation to mt7530_p5_mode_str, and the enum elements.
If PHY muxing is not detected, the default mode, GMAC5, will be used.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MT7530_PMCR_P() registers are on MT7530, MT7531, and the switch on the
MT7988 SoC. Rename the definition for them to MT753X_PMCR_P(). Bit 15 is
for MT7530 only. Add MT7530 prefix to the definition for bit 15.
Use GENMASK and FIELD_PREP for PMCR_IFG_XMIT().
Rename PMCR_TX_EN and PMCR_RX_EN to PMCR_MAC_TX_EN and PMCR_MAC_TX_EN to
follow the naming on the "MT7621 Giga Switch Programming Guide v0.3",
"MT7531 Reference Manual for Development Board v1.0", and "MT7988A Wi-Fi 7
Generation Router Platform: Datasheet (Open Version) v0.1" documents.
These documents show that PMCR_RX_FC_EN is at bit 5. Correct this along
with renaming it to PMCR_FORCE_RX_FC_EN, and the same for PMCR_TX_FC_EN.
Remove PMCR_SPEED_MASK which doesn't have a use.
Rename the force mode definitions for MT7531 to FORCE_MODE. Add MASK at the
end for the mask that includes all force mode definitions.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MT7531_FORCE_EEE1G and MT7531_FORCE_EEE100 bits let the
PMCR_FORCE_EEE1G and PMCR_FORCE_EEE100 bits determine the 1G/100 EEE
abilities of the MAC. If MT7531_FORCE_EEE1G and MT7531_FORCE_EEE100 are
unset, the abilities are left to be determined by PHY auto polling.
The commit 40b5d2f15c09 ("net: dsa: mt7530: Add support for EEE features")
made it so that the PMCR_FORCE_EEE1G and PMCR_FORCE_EEE100 bits are set on
mt753x_phylink_mac_link_up(). But it did not set the MT7531_FORCE_EEE1G and
MT7531_FORCE_EEE100 bits. Because of this, the EEE abilities will be
determined by PHY auto polling, regardless of the result of phy_init_eee().
Define these bits and add them to the MT7531_FORCE_MODE mask which is set
in mt7531_setup_common(). With this, there won't be any EEE abilities set
when phy_init_eee() returns a negative value.
Thanks to Russell for explaining when phy_init_eee() could return a
negative value below.
Looking at phy_init_eee(), it could return a negative value when:
1. phydev->drv is NULL
2. if genphy_c45_eee_is_active() returns negative
3. if genphy_c45_eee_is_active() returns zero, it returns -EPROTONOSUPPORT
4. if phy_set_bits_mmd() fails (e.g. communication error with the PHY)
If we then look at genphy_c45_eee_is_active(), then:
genphy_c45_read_eee_adv() and genphy_c45_read_eee_lpa() propagate their
non-zero return values, otherwise this function returns zero or positive
integer.
If we then look at genphy_c45_read_eee_adv(), then a failure of
phy_read_mmd() would cause a negative value to be returned.
Looking at genphy_c45_read_eee_lpa(), the same is true.
So, it can be summarised as:
- phydev->drv is NULL
- there is a communication error accessing the PHY
- EEE is not active
otherwise, it returns zero on success.
If one wishes to determine whether an error occurred vs EEE not being
supported through negotiation for the negotiated speed, if it returns
-EPROTONOSUPPORT in the latter case. Other error codes mean either the
driver has been unloaded or communication error.
In conclusion, determining the EEE abilities by PHY auto polling shouldn't
result in having any EEE abilities enabled, when one of the last two
situations in the summary happens. And it seems that if phydev->drv is
NULL, there would be bigger problems with the device than a broken link. So
this is not a bugfix.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only blink if the link is up on a LED which is programmed to also
indicate link-status.
Otherwise, if both LEDs are in use to indicate different speeds, the
resulting blinking being inverted on LEDs which aren't switched on at
a specific speed is quite counter-intuitive.
Also make sure that state left behind by reset or the bootloader is
recognized correctly including the half-duplex and full-duplex bits as
well as the (unsupported by Linux netdev trigger semantics) link-down
bit.
Fixes: c66937b0f8db ("net: phy: mediatek-ge-soc: support PHY LEDs")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since call_rcu, which is called in the hlist_for_each_entry_rcu traversal
of gtp_dellink, is not part of the RCU read critical section, it
is possible that the RCU grace period will pass during the traversal and
the key will be free.
To prevent this, it should be changed to hlist_for_each_entry_safe.
Fixes: 94dc550a5062 ("gtp: fix an use-after-free in ipv4_pdp_find()")
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use struct_group_attr() in __packed structs, instead of struct_group().
Below you can see the pahole output before/after changes:
pahole -C smb2_file_network_open_info fs/smb/client/smb2ops.o
struct smb2_file_network_open_info {
union {
struct {
__le64 CreationTime; /* 0 8 */
__le64 LastAccessTime; /* 8 8 */
__le64 LastWriteTime; /* 16 8 */
__le64 ChangeTime; /* 24 8 */
__le64 AllocationSize; /* 32 8 */
__le64 EndOfFile; /* 40 8 */
__le32 Attributes; /* 48 4 */
}; /* 0 56 */
struct {
__le64 CreationTime; /* 0 8 */
__le64 LastAccessTime; /* 8 8 */
__le64 LastWriteTime; /* 16 8 */
__le64 ChangeTime; /* 24 8 */
__le64 AllocationSize; /* 32 8 */
__le64 EndOfFile; /* 40 8 */
__le32 Attributes; /* 48 4 */
} network_open_info; /* 0 56 */
}; /* 0 56 */
__le32 Reserved; /* 56 4 */
/* size: 60, cachelines: 1, members: 2 */
/* last cacheline: 60 bytes */
} __attribute__((__packed__));
pahole -C smb2_file_network_open_info fs/smb/client/smb2ops.o
struct smb2_file_network_open_info {
union {
struct {
__le64 CreationTime; /* 0 8 */
__le64 LastAccessTime; /* 8 8 */
__le64 LastWriteTime; /* 16 8 */
__le64 ChangeTime; /* 24 8 */
__le64 AllocationSize; /* 32 8 */
__le64 EndOfFile; /* 40 8 */
__le32 Attributes; /* 48 4 */
} __attribute__((__packed__)); /* 0 52 */
struct {
__le64 CreationTime; /* 0 8 */
__le64 LastAccessTime; /* 8 8 */
__le64 LastWriteTime; /* 16 8 */
__le64 ChangeTime; /* 24 8 */
__le64 AllocationSize; /* 32 8 */
__le64 EndOfFile; /* 40 8 */
__le32 Attributes; /* 48 4 */
} __attribute__((__packed__)) network_open_info; /* 0 52 */
}; /* 0 52 */
__le32 Reserved; /* 52 4 */
/* size: 56, cachelines: 1, members: 2 */
/* last cacheline: 56 bytes */
};
pahole -C smb_com_open_rsp fs/smb/client/cifssmb.o
struct smb_com_open_rsp {
...
union {
struct {
__le64 CreationTime; /* 48 8 */
__le64 LastAccessTime; /* 56 8 */
/* --- cacheline 1 boundary (64 bytes) --- */
__le64 LastWriteTime; /* 64 8 */
__le64 ChangeTime; /* 72 8 */
__le32 FileAttributes; /* 80 4 */
}; /* 48 40 */
struct {
__le64 CreationTime; /* 48 8 */
__le64 LastAccessTime; /* 56 8 */
/* --- cacheline 1 boundary (64 bytes) --- */
__le64 LastWriteTime; /* 64 8 */
__le64 ChangeTime; /* 72 8 */
__le32 FileAttributes; /* 80 4 */
} common_attributes; /* 48 40 */
}; /* 48 40 */
...
/* size: 111, cachelines: 2, members: 14 */
/* last cacheline: 47 bytes */
} __attribute__((__packed__));
pahole -C smb_com_open_rsp fs/smb/client/cifssmb.o
struct smb_com_open_rsp {
...
union {
struct {
__le64 CreationTime; /* 48 8 */
__le64 LastAccessTime; /* 56 8 */
/* --- cacheline 1 boundary (64 bytes) --- */
__le64 LastWriteTime; /* 64 8 */
__le64 ChangeTime; /* 72 8 */
__le32 FileAttributes; /* 80 4 */
} __attribute__((__packed__)); /* 48 36 */
struct {
__le64 CreationTime; /* 48 8 */
__le64 LastAccessTime; /* 56 8 */
/* --- cacheline 1 boundary (64 bytes) --- */
__le64 LastWriteTime; /* 64 8 */
__le64 ChangeTime; /* 72 8 */
__le32 FileAttributes; /* 80 4 */
} __attribute__((__packed__)) common_attributes; /* 48 36 */
}; /* 48 36 */
...
/* size: 107, cachelines: 2, members: 14 */
/* last cacheline: 43 bytes */
} __attribute__((__packed__));
pahole -C FILE_ALL_INFO fs/smb/client/cifssmb.o
typedef struct {
union {
struct {
__le64 CreationTime; /* 0 8 */
__le64 LastAccessTime; /* 8 8 */
__le64 LastWriteTime; /* 16 8 */
__le64 ChangeTime; /* 24 8 */
__le32 Attributes; /* 32 4 */
}; /* 0 40 */
struct {
__le64 CreationTime; /* 0 8 */
__le64 LastAccessTime; /* 8 8 */
__le64 LastWriteTime; /* 16 8 */
__le64 ChangeTime; /* 24 8 */
__le32 Attributes; /* 32 4 */
} common_attributes; /* 0 40 */
}; /* 0 40 */
...
/* size: 113, cachelines: 2, members: 17 */
/* last cacheline: 49 bytes */
} __attribute__((__packed__)) FILE_ALL_INFO;
pahole -C FILE_ALL_INFO fs/smb/client/cifssmb.o
typedef struct {
union {
struct {
__le64 CreationTime; /* 0 8 */
__le64 LastAccessTime; /* 8 8 */
__le64 LastWriteTime; /* 16 8 */
__le64 ChangeTime; /* 24 8 */
__le32 Attributes; /* 32 4 */
} __attribute__((__packed__)); /* 0 36 */
struct {
__le64 CreationTime; /* 0 8 */
__le64 LastAccessTime; /* 8 8 */
__le64 LastWriteTime; /* 16 8 */
__le64 ChangeTime; /* 24 8 */
__le32 Attributes; /* 32 4 */
} __attribute__((__packed__)) common_attributes; /* 0 36 */
}; /* 0 36 */
...
/* size: 109, cachelines: 2, members: 17 */
/* last cacheline: 45 bytes */
} __attribute__((__packed__)) FILE_ALL_INFO;
Fixes: 0015eb6e1238 ("smb: client, common: fix fortify warnings")
Cc: stable@vger.kernel.org
Reviewed-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
In order to fix perf's callchain parse error for LoongArch, we implement
perf_arch_fetch_caller_regs() which fills several necessary registers
used for callchain unwinding, including sp, fp, and era. This is similar
to the following commits.
commit b3eac0265bf6:
("arm: perf: Fix callchain parse error with kernel tracepoint events")
commit 5b09a094f2fb:
("arm64: perf: Fix callchain parse error with kernel tracepoint events")
commit 9a7e8ec0d4cc:
("riscv: perf: Fix callchain parse error with kernel tracepoint events")
Test with commands:
perf record -e sched:sched_switch -g --call-graph dwarf
perf report
Without this patch:
Children Self Command Shared Object Symbol
........ ........ ............. ................. ....................
43.41% 43.41% swapper [unknown] [k] 0000000000000000
10.94% 10.94% loong-container [unknown] [k] 0000000000000000
|
|--5.98%--0x12006ba38
|
|--2.56%--0x12006bb84
|
--2.40%--0x12006b6b8
With this patch, callchain can be parsed correctly:
Children Self Command Shared Object Symbol
........ ........ ............. ................. ....................
47.57% 47.57% swapper [kernel.vmlinux] [k] __schedule
|
---__schedule
26.76% 26.76% loong-container [kernel.vmlinux] [k] __schedule
|
|--13.78%--0x12006ba38
| |
| |--9.19%--__schedule
| |
| --4.59%--handle_syscall
| do_syscall
| sys_futex
| do_futex
| futex_wait
| futex_wait_queue_me
| hrtimer_start_range_ns
| __schedule
|
|--8.38%--0x12006bb84
| handle_syscall
| do_syscall
| sys_epoll_pwait
| do_epoll_wait
| schedule_hrtimeout_range_clock
| hrtimer_start_range_ns
| __schedule
|
--4.59%--0x12006b6b8
handle_syscall
do_syscall
sys_nanosleep
hrtimer_nanosleep
do_nanosleep
hrtimer_start_range_ns
__schedule
Cc: stable@vger.kernel.org
Fixes: b37042b2bb7cd751f0 ("LoongArch: Add perf events support")
Reported-by: Youling Tang <tangyouling@kylinos.cn>
Suggested-by: Youling Tang <tangyouling@kylinos.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
As with most architectures, allow handling of read faults in VMAs that
have VM_WRITE but without VM_READ (WRITE implies READ).
Otherwise, reading before writing a write-only memory will error while
reading after writing everything is fine.
BTW, move the VM_EXEC judgement before VM_READ/VM_WRITE to make logic a
little clearer.
Cc: stable@vger.kernel.org
Fixes: 09cfefb7fa70c3af01 ("LoongArch: Add memory management")
Signed-off-by: Jiantao Shan <shanjiantao@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
With LLVM=1 and W=1 we get:
./include/asm-generic/tlb.h:629:10: error: parameter 'ptep' set
but not used [-Werror,-Wunused-but-set-parameter]
We fixed a similar issue via Arnd in the introducing commit, missed the
LoongArch variant. Turns out, there is no need for LoongArch to have a
custom variant, so let's just drop it and rely on the asm-generic one.
Fixes: 4d5bf0b6183f ("mm/mmu_gather: add tlb_remove_tlb_entries()")
Closes: https://lkml.kernel.org/r/CANiq72mQh3O9S4umbvrKBgMMorty48UMwS01U22FR0mRyd3cyQ@mail.gmail.com
Reported-by: Miguel Ojeda <ojeda@kernel.org>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Tested-by: Miguel Ojeda <ojeda@kernel.org>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
In commit 85fcde402db191b5 ("kexec: split crashkernel reservation code
out from crash_core.c"), crashkernel reservation code is split out from
crash_core.c, and add CRASH_RESERVE to control it. And also rename each
ARCH's <asm/crash_core.h> to <asm/crash_reserve.h> accordingly.
But the relevant part in LoongArch is missed. Do it now.
Fixes: 85fcde402db1 ("kexec: split crashkernel reservation code out from crash_core.c")
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
The default nna (node_nr_active) is used when the pool isn't tied to a
specific NUMA node. This can happen in the following cases:
1. On NUMA, if per-node pwq init failure and the fallback pwq is used.
2. On NUMA, if a pool is configured to span multiple nodes.
3. On single node setups.
5797b1c18919 ("workqueue: Implement system-wide nr_active enforcement for
unbound workqueues") set the default nna->max to min_active because only #1
was being considered. For #2 and #3, using min_active means that the max
concurrency in normal operation is pushed down to min_active which is
currently 8, which can obviously lead to performance issues.
exact value nna->max is set to doesn't really matter. #2 can only happen if
the workqueue is intentionally configured to ignore NUMA boundaries and
there's no good way to distribute max_active in this case. #3 is the default
behavior on single node machines.
Let's set it the default nna->max to max_active. This fixes the artificially
lowered concurrency problem on single node machines and shouldn't hurt
anything for other cases.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Fixes: 5797b1c18919 ("workqueue: Implement system-wide nr_active enforcement for unbound workqueues")
Link: https://lore.kernel.org/dm-devel/20240410084531.2134621-1-shinichiro.kawasaki@wdc.com/
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Delete fence fallback timer to fix the ramdom
use-after-free issue.
v2: move to amdgpu_mes.c
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Acked-by: Lijo Lazar <lijo.lazar@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This avoids a potential conflict with firmwares with the newer
HDP flush mechanism.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Here are the corrections needed for the queue ring buffer size
calculation for the following cases:
- Remove the KIQ VM flush ring usage.
- Add the invalidate TLBs packet for gfx10 and gfx11 queue.
- There's no VM flush and PFP sync, so remove the gfx9 real
ring and compute ring buffer usage.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Do VRAM accounting when doing migrations to vram to make sure
there is enough available VRAM and migrating to VRAM doesn't evict
other possible non-unified memory BOs. If migrating to VRAM fails,
driver can fall back to using system memory seamlessly.
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
During mode-2 reset, pci config space registers are affected at device
side. However, certain platforms have switches which assign virtual BAR
addresses and returns the same even after device is reset. This
affects pci_restore_state() as it doesn't issue another config write, if
the value read is same as the saved value.
Add a workaround to write saved config space values from driver side.
Presently, these switches are in platforms with SMU v13.0.6 SOCs, hence
restrict the workaround only to those.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
umsch test needs full GPU functionality(e.g., VM update, TLB flush,
possibly buffer moving under memory pressure) which may be not ready
under these states. Just skip it to avoid potential issues.
Signed-off-by: Lang Yu <Lang.Yu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Veerabadhran Gopalakrishnan <Veerabadhran.Gopalakrishnan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Handle the case that the restore worker was already scheduled by another
eviction while the restore was in progress.
Fixes: 9a1c1339abf9 ("drm/amdkfd: Run restore_workers on freezable WQs")
Signed-off-by: Felix Kuehling <felix.kuehling@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Tested-by: Yunxiang Li <Yunxiang.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Make SVM BOs more likely to get evicted than other BOs. These BOs
opportunistically use available VRAM, but can fall back relatively
seamlessly to system memory. It also avoids SVM migrations evicting
other, more important BOs as they will evict other SVM allocations
first.
Signed-off-by: Felix Kuehling <felix.kuehling@amd.com>
Acked-by: Mukul Joshi <mukul.joshi@amd.com>
Tested-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The vpe dpm settings should be done before firmware is loaded.
Otherwise, the frequency cannot be successfully raised.
Signed-off-by: Peyton Lee <peytolee@amd.com>
Reviewed-by: Lang Yu <lang.yu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
HDP Flush request bit can be kept unique per AID, and doesn't need to be
unique SOC-wide. Assign only bits 10-13 for SDMA v4.4.2.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
gpu_od should be removed if it's an empty directory
Signed-off-by: Ma Jun <Jun.Ma2@amd.com>
Reported-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Suggested-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
When page table BOs were evicted but not validated before
updating page tables, VM is still in evicting state,
amdgpu_vm_update_range returns -EBUSY and
restore_process_worker runs into a dead loop.
v2: Split the BO validation and page table update into two
separate loops in amdgpu_amdkfd_restore_process_bos. (Felix)
1.Validate BOs
2.Validate VM (and DMABuf attachments)
3.Update page tables for the BOs validated above
Fixes: 50661eb1a2c8 ("drm/amdgpu: Auto-validate DMABuf imports in compute VMs")
Signed-off-by: Lang Yu <Lang.Yu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Free the sync object if the memory allocation fails for any
reason.
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Handle case that dma_fence_get_rcu_safe returns NULL.
If restore work is already scheduled, only update its timer. The same
work item cannot be queued twice, so undo the extra queue eviction.
Fixes: 9a1c1339abf9 ("drm/amdkfd: Run restore_workers on freezable WQs")
Signed-off-by: Felix Kuehling <felix.kuehling@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Tested-by: Gang BA <Gang.Ba@amd.com>
Reviewed-by: Gang BA <Gang.Ba@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Otherwise we can end up with a frame on unsuspend where color management
is not applied when userspace has not committed themselves.
Fixes re-applying color management on Steam Deck/Gamescope on S3 resume.
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Benjamin Tissoires says:
====================
Introduce bpf_wq
This is a followup of sleepable bpf_timer[0].
When discussing sleepable bpf_timer, it was thought that we should give
a try to bpf_wq, as the 2 APIs are similar but distinct enough to
justify a new one.
So here it is.
I tried to keep as much as possible common code in kernel/bpf/helpers.c
but I couldn't get away with code duplication in kernel/bpf/verifier.c.
This series introduces a basic bpf_wq support:
- creation is supported
- assignment is supported
- running a simple bpf_wq is also supported.
We will probably need to extend the API further with:
- a full delayed_work API (can be piggy backed on top with a correct
flag)
- bpf_wq_cancel() <- apparently not, this is shooting ourself in the
foot
- bpf_wq_cancel_sync() (for sleepable programs)
- documentation
---
For reference, the use cases I have in mind:
---
Basically, I need to be able to defer a HID-BPF program for the
following reasons (from the aforementioned patch):
1. defer an event:
Sometimes we receive an out of proximity event, but the device can not
be trusted enough, and we need to ensure that we won't receive another
one in the following n milliseconds. So we need to wait those n
milliseconds, and eventually re-inject that event in the stack.
2. inject new events in reaction to one given event:
We might want to transform one given event into several. This is the
case for macro keys where a single key press is supposed to send
a sequence of key presses. But this could also be used to patch a
faulty behavior, if a device forgets to send a release event.
3. communicate with the device in reaction to one event:
We might want to communicate back to the device after a given event.
For example a device might send us an event saying that it came back
from sleeping state and needs to be re-initialized.
Currently we can achieve that by keeping a userspace program around,
raise a bpf event, and let that userspace program inject the events and
commands.
However, we are just keeping that program alive as a daemon for just
scheduling commands. There is no logic in it, so it doesn't really justify
an actual userspace wakeup. So a kernel workqueue seems simpler to handle.
bpf_timers are currently running in a soft IRQ context, this patch
series implements a sleppable context for them.
Cheers,
Benjamin
[0] https://lore.kernel.org/all/20240408-hid-bpf-sleepable-v6-0-0499ddd91b94@kernel.org/
Changes in v2:
- took previous review into account
- mainly dropped BPF_F_WQ_SLEEPABLE
- Link to v1: https://lore.kernel.org/r/20240416-bpf_wq-v1-0-c9e66092f842@kernel.org
====================
Link: https://lore.kernel.org/r/20240420-bpf_wq-v2-0-6c986a5a741f@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Allows to test if allocation/free works
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20240420-bpf_wq-v2-16-6c986a5a741f@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
again, copy/paste from bpf_timer_start().
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20240420-bpf_wq-v2-15-6c986a5a741f@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
We assign the callback and set everything up.
The actual tests of these callbacks will be done when bpf_wq_start() is
available.
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20240420-bpf_wq-v2-14-6c986a5a741f@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
To support sleepable async callbacks, we need to tell push_async_cb()
whether the cb is sleepable or not.
The verifier now detects that we are in bpf_wq_set_callback_impl and
can allow a sleepable callback to happen.
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20240420-bpf_wq-v2-13-6c986a5a741f@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Allows to test if allocation/free works
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20240420-bpf_wq-v2-12-6c986a5a741f@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
We need to teach the verifier about the second argument which is declared
as void * but which is of type KF_ARG_PTR_TO_MAP. We could have dropped
this extra case if we declared the second argument as struct bpf_map *,
but that means users will have to do extra casting to have their program
compile.
We also need to duplicate the timer code for the checking if the map
argument is matching the provided workqueue.
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20240420-bpf_wq-v2-11-6c986a5a741f@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
We simply try in all supported map types if we can store/load a bpf_wq.
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20240420-bpf_wq-v2-10-6c986a5a741f@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Since call_rcu, which is called in the hlist_for_each_entry_rcu traversal
of tcp_ao_connect_init, is not part of the RCU read critical section, it
is possible that the RCU grace period will pass during the traversal and
the key will be free.
To prevent this, it should be changed to hlist_for_each_entry_safe.
Fixes: 7c2ffaf21bd6 ("net/tcp: Calculate TCP-AO traffic keys")
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Dmitry Safonov <0x7f454c46@gmail.com>
Link: https://lore.kernel.org/r/ZiYu9NJ/ClR8uSkH@v4bel-B760M-AORUS-ELITE-AX
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If we no longer hold RTNL, we must use netdev_master_upper_dev_get_rcu()
instead of netdev_master_upper_dev_get().
Fixes: ba0f78069423 ("neighbour: no longer hold RTNL in neigh_dump_info()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240421185753.1808077-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some usb drivers try to set small skb->truesize and break
core networking stacks.
In this patch, I removed one of the skb->truesize overide.
I also replaced one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c61172342 ("net: cdc_ncm: reduce skb truesize
in rx path")
Fixes: f8ebb3ac881b ("net: usb: ax88179_178a: Fix packet receiving")
Reported-by: shironeko <shironeko@tesaguri.club>
Closes: https://lore.kernel.org/netdev/c110f41a0d2776b525930f213ca9715c@tesaguri.club/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jose Alonso <joalonsof@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240421193828.1966195-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot was able to trigger a NULL deref in fib_validate_source()
in an old tree [1].
It appears the bug exists in latest trees.
All calls to __in_dev_get_rcu() must be checked for a NULL result.
[1]
general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 2 PID: 3257 Comm: syz-executor.3 Not tainted 5.10.0-syzkaller #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
RIP: 0010:fib_validate_source+0xbf/0x15a0 net/ipv4/fib_frontend.c:425
Code: 18 f2 f2 f2 f2 42 c7 44 20 23 f3 f3 f3 f3 48 89 44 24 78 42 c6 44 20 27 f3 e8 5d 88 48 fc 4c 89 e8 48 c1 e8 03 48 89 44 24 18 <42> 80 3c 20 00 74 08 4c 89 ef e8 d2 15 98 fc 48 89 5c 24 10 41 bf
RSP: 0018:ffffc900015fee40 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff88800f7a4000 RCX: ffff88800f4f90c0
RDX: 0000000000000000 RSI: 0000000004001eac RDI: ffff8880160c64c0
RBP: ffffc900015ff060 R08: 0000000000000000 R09: ffff88800f7a4000
R10: 0000000000000002 R11: ffff88800f4f90c0 R12: dffffc0000000000
R13: 0000000000000000 R14: 0000000000000000 R15: ffff88800f7a4000
FS: 00007f938acfe6c0(0000) GS:ffff888058c00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f938acddd58 CR3: 000000001248e000 CR4: 0000000000352ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
ip_route_use_hint+0x410/0x9b0 net/ipv4/route.c:2231
ip_rcv_finish_core+0x2c4/0x1a30 net/ipv4/ip_input.c:327
ip_list_rcv_finish net/ipv4/ip_input.c:612 [inline]
ip_sublist_rcv+0x3ed/0xe50 net/ipv4/ip_input.c:638
ip_list_rcv+0x422/0x470 net/ipv4/ip_input.c:673
__netif_receive_skb_list_ptype net/core/dev.c:5572 [inline]
__netif_receive_skb_list_core+0x6b1/0x890 net/core/dev.c:5620
__netif_receive_skb_list net/core/dev.c:5672 [inline]
netif_receive_skb_list_internal+0x9f9/0xdc0 net/core/dev.c:5764
netif_receive_skb_list+0x55/0x3e0 net/core/dev.c:5816
xdp_recv_frames net/bpf/test_run.c:257 [inline]
xdp_test_run_batch net/bpf/test_run.c:335 [inline]
bpf_test_run_xdp_live+0x1818/0x1d00 net/bpf/test_run.c:363
bpf_prog_test_run_xdp+0x81f/0x1170 net/bpf/test_run.c:1376
bpf_prog_test_run+0x349/0x3c0 kernel/bpf/syscall.c:3736
__sys_bpf+0x45c/0x710 kernel/bpf/syscall.c:5115
__do_sys_bpf kernel/bpf/syscall.c:5201 [inline]
__se_sys_bpf kernel/bpf/syscall.c:5199 [inline]
__x64_sys_bpf+0x7c/0x90 kernel/bpf/syscall.c:5199
Fixes: 02b24941619f ("ipv4: use dst hint for ipv4 list receive")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240421184326.1704930-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Jonathan Heathcote reported a regression caused by blamed commit
on aarch64 architecture.
x86 happens to have irq-safe __this_cpu_add_return()
and __this_cpu_sub(), but this is not generic.
I think my confusion came from "struct sock" argument,
because these helpers are called with a locked socket.
But the memory accounting is per-proto (and per-cpu after
the blamed commit). We might cleanup these helpers later
to directly accept a "struct proto *proto" argument.
Switch to this_cpu_add_return() and this_cpu_xchg()
operations, and get rid of preempt_disable()/preempt_enable() pairs.
Fast path becomes a bit faster as a result :)
Many thanks to Jonathan Heathcote for his awesome report and
investigations.
Fixes: 3cd3399dd7a8 ("net: implement per-cpu reserves for memory_allocated")
Reported-by: Jonathan Heathcote <jonathan.heathcote@bbc.co.uk>
Closes: https://lore.kernel.org/netdev/VI1PR01MB42407D7947B2EA448F1E04EFD10D2@VI1PR01MB4240.eurprd01.prod.exchangelabs.com/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Shakeel Butt <shakeel.butt@linux.dev>
Link: https://lore.kernel.org/r/20240421175248.1692552-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently bpf_wq_cancel_and_free() is just a placeholder as there is
no memory allocation for bpf_wq just yet.
Again, duplication of the bpf_timer approach
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20240420-bpf_wq-v2-9-6c986a5a741f@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Introduce support for KF_ARG_PTR_TO_WORKQUEUE. The kfuncs will use bpf_wq
as argument and that will be recognized as workqueue argument by verifier.
bpf_wq_kern casting can happen inside kfunc, but using bpf_wq in
argument makes life easier for users who work with non-kern type in BPF
progs.
Duplicate process_timer_func into process_wq_func.
meta argument is only needed to ensure bpf_wq_init's workqueue and map
arguments are coming from the same map (map_uid logic is necessary for
correct inner-map handling), so also amend check_kfunc_args() to
match what helpers functions check is doing.
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20240420-bpf_wq-v2-8-6c986a5a741f@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
When a kfunc is declared with a KF_ARG_PTR_TO_MAP, we should have
reg->map_ptr set to a non NULL value, otherwise, that means that the
underlying type is not a map.
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20240420-bpf_wq-v2-7-6c986a5a741f@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
cp include/uapi/linux/bpf.h tools/include/uapi/linux/bpf.h
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20240420-bpf_wq-v2-6-6c986a5a741f@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Mostly a copy/paste from the bpf_timer API, without the initialization
and free, as they will be done in a separate patch.
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20240420-bpf_wq-v2-5-6c986a5a741f@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Same reason than most bpf_timer* functions, we need almost the same for
workqueues.
So extract the generic part out of it so bpf_wq_cancel_and_free can reuse
it.
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20240420-bpf_wq-v2-4-6c986a5a741f@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
In the same way we have a generic __bpf_async_init(), we also need
to share code between timer and workqueue for the set_callback call.
We just add an unused flags parameter, as it will be used for workqueues.
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20240420-bpf_wq-v2-3-6c986a5a741f@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
