| Age | Commit message (Collapse) | Author |
|---|
|
While the individual CHARLCD_BL_xxx options have help texts, the
menu itself does not. Fix this.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Mans Rullgard <mans@mansr.com>
[Added a bit more text to address Linus' suggestion]
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
|
|
panel_attach
In panel_attach, if misc_register fails, we need to delete scan_timer,
which was setup in keypad_init->init_scan_timer.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
|
|
Most of the bridge device's vlan init bugs come from the fact that its
default pvid is created at the wrong time, way too early in ndo_init()
before the device is even assigned an ifindex. It introduces a bug when the
bridge's dev_addr is added as fdb during the initial default pvid creation
the notification has ifindex/NDA_MASTER both equal to 0 (see example below)
which really makes no sense for user-space[0] and is wrong.
Usually user-space software would ignore such entries, but they are
actually valid and will eventually have all necessary attributes.
It makes much more sense to send a notification *after* the device has
registered and has a proper ifindex allocated rather than before when
there's a chance that the registration might still fail or to receive
it with ifindex/NDA_MASTER == 0. Note that we can remove the fdb flush
from br_vlan_flush() since that case can no longer happen. At
NETDEV_REGISTER br->default_pvid is always == 1 as it's initialized by
br_vlan_init() before that and at NETDEV_UNREGISTER it can be anything
depending why it was called (if called due to NETDEV_REGISTER error
it'll still be == 1, otherwise it could be any value changed during the
device life time).
For the demonstration below a small change to iproute2 for printing all fdb
notifications is added, because it contained a workaround not to show
entries with ifindex == 0.
Command executed while monitoring: $ ip l add br0 type bridge
Before (both ifindex and master == 0):
$ bridge monitor fdb
36:7e:8a:b3:56:ba dev * vlan 1 master * permanent
After (proper br0 ifindex):
$ bridge monitor fdb
e6:2a:ae:7a:b7:48 dev br0 vlan 1 master br0 permanent
v4: move only the default pvid init/deinit to NETDEV_REGISTER/UNREGISTER
v3: send the correct v2 patch with all changes (stub should return 0)
v2: on error in br_vlan_init set br->vlgrp to NULL and return 0 in
the br_vlan_bridge_event stub when bridge vlans are disabled
[0] https://bugzilla.kernel.org/show_bug.cgi?id=204389
Reported-by: michael-dev <michael-dev@fami-braun.de>
Fixes: 5be5a2df40f0 ("bridge: Add filtering support for default_pvid")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Orion5.x systems are still using machine files and not device-tree.
Commit 96cb4342382290c9 ("net: mvmdio: allow up to three clocks to be
specified for orion-mdio") has replaced devm_clk_get() with of_clk_get(),
leading to a oops at boot and not working network, as reported in
https://lists.debian.org/debian-arm/2019/07/msg00088.html and possibly in
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=908712.
Link: https://lists.debian.org/debian-arm/2019/07/msg00088.html
Fixes: 96cb4342382290c9 ("net: mvmdio: allow up to three clocks to be specified for orion-mdio")
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FASTOPEN is not possible with SMC. sendmsg() with msg_flag MSG_FASTOPEN
triggers a fallback to TCP if the socket is in state SMC_INIT.
But if a nonblocking connect is already started, fallback to TCP
is no longer possible, even though the socket may still be in state
SMC_INIT.
And if a nonblocking connect is already started, a listen() call
does not make sense.
Reported-by: syzbot+bd8cc73d665590a1fcad@syzkaller.appspotmail.com
Fixes: 50717a37db032 ("net/smc: nonblocking connect rework")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The setsockopts options TCP_NODELAY and TCP_CORK may schedule the
tx worker. Make sure the socket is not yet moved into SMC_CLOSED
state (for instance by a shutdown SHUT_RDWR call).
Reported-by: syzbot+92209502e7aab127c75f@syzkaller.appspotmail.com
Reported-by: syzbot+b972214bb803a343f4fe@syzkaller.appspotmail.com
Fixes: 01d2f7e2cdd31 ("net/smc: sockopts TCP_NODELAY and TCP_CORK")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
desc_cnt and data_cnt should always be equal. In the case of a dropped
packet desc_cnt was still getting updated (correctly), data_cnt
was not. To eliminate this bug and prevent it from recurring this
patch combines them into one ring level cnt.
Signed-off-by: Catherine Sullivan <csully@google.com>
Reviewed-by: Sagi Shahar <sagis@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The nexthop path in rt6_update_exception_stamp_rt needs to call
rcu_read_unlock if it fails to find a fib6_nh match rather than
just returning.
Fixes: e659ba31d806 ("ipv6: Handle all fib6_nh in a nexthop in exception handling")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure that shutdown never works, and at the same time document how
I tested to came to the conclusion that currently reuse is not possible.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Looks like we were slightly overzealous with the shutdown()
cleanup. Even though the sock->sk_state can reach CLOSED again,
socket->state will not got back to SS_UNCONNECTED once
connections is ESTABLISHED. Meaning we will see EISCONN if
we try to reconnect, and EINVAL if we try to listen.
Only listen sockets can be shutdown() and reused, but since
ESTABLISHED sockets can never be re-connected() or used for
listen() we don't need to try to clean up the ULP state early.
Fixes: 32857cf57f92 ("net/tls: fix transition through disconnect with close")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
msi.c is not a module on its own right and should not have the
MODULE_[LICENSE|VERSION|AUTHOR|DESCRIPTION] definitions.
This caused a regression noticed by lkp with the following back
trace:
WARNING: CPU: 0 PID: 1 at kernel/params.c:861 param_sysfs_init+0xb1/0x20a
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.2.0-rc1-00018-g26b3a37b928457 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
RIP: 0010:param_sysfs_init+0xb1/0x20a
Code: 24 38 e8 ec 17 2e fd 49 8b 7c 24 38 e8 76 fe ff ff 48 85 c0 48 89 c5 74 25 31 d2 4c 89 e6 48 89 c7 e8 6d 6f 3c fd 85 c0 74 02 <0f> 0b 48 89 ef 31 f6 e8 5d 70 a7 fe 48 89 ef e8 95 52 a7 fe 48 83
RSP: 0000:ffff88806b0ffe30 EFLAGS: 00010282
RAX: 00000000ffffffef RBX: ffffffff83774220 RCX: ffff88806a85e880
RDX: 00000000ffffffef RSI: ffff88806b000400 RDI: ffff88806a8608c0
RBP: ffff88806b392000 R08: ffffed100d61ff59 R09: ffffed100d61ff59
R10: 0000000000000001 R11: ffffed100d61ff58 R12: ffffffff83974bc0
R13: 0000000000000004 R14: 0000000000000028 R15: 00000000000003b9
FS: 0000000000000000(0000) GS:ffff88806b800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 000000000380e000 CR4: 00000000000406b0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
? file_caps_disable+0x10/0x10
? locate_module_kobject+0xf2/0xf2
do_one_initcall+0x47/0x1f0
kernel_init_freeable+0x1b1/0x243
? rest_init+0xd0/0xd0
kernel_init+0xa/0x130
? calculate_sigpending+0x63/0x80
? rest_init+0xd0/0xd0
ret_from_fork+0x1f/0x30
---[ end trace 78201497ae74cc91 ]---
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 26b3a37b9284 ("NTB: Introduce MSI library")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A bunch of small, device specific things here plus a DT bindings fix
for the new validatable YAML binding format.
The most notable thing is the fix for GPIO chip selects which fixes a
corner case in updates of that code to modern APIs, unfortunately due
to a historical mess the code around GPIO support is obscure, fragile
and an ABI which makes and attempt to improve the situation painful"
* tag 'spi-fix-v5.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: pxa2xx: Add support for Intel Tiger Lake
spi: bcm2835: Fix 3-wire mode if DMA is enabled
spi: pxa2xx: Balance runtime PM enable/disable on error
spi: gpio: Add SPI_MASTER_GPIO_SS flag
spi: spi-fsl-qspi: change i.MX7D RX FIFO size
spi: dt-bindings: spi-controller: remove unnecessary 'maxItems: 1' from reg
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A few small driver specific fixes here plus one core fix for a
refcounting problem with DT which will have little practical impact
unless overlays are used"
* tag 'regulator-fix-v5.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: of: Add of_node_put() before return in function
regulator: lp87565: Fix probe failure for "ti,lp87565"
regulator: axp20x: fix DCDC5 and DCDC6 for AXP803
regulator: axp20x: fix DCDCA and DCDCD for AXP806
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
"A fix to the Kselftest framework to save and restore errno and a fix
to livepatch to push and pop dynamic debug config"
* tag 'linux-kselftest-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/livepatch: push and pop dynamic debug config
kselftest: save-and-restore errno to allow for %m formatting
|
|
If getdents64 is killed or hits on segfault, it'll leave cgroups
directories in sysfs pinned leaking memory because the kernfs node
won't be freed on rmdir and the parent neither.
Repro:
# for i in `seq 1000`; do mkdir $i; done
# rmdir *
# for i in `seq 1000`; do mkdir $i; done
# rmdir *
# for i in `seq 1000`; do while :; do ls $i/ >/dev/null; done & done
# while :; do killall ls; done
kernfs_node_cache in /proc/slabinfo keeps going up as expected.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org # goes way back to original sysfs days
Link: https://lore.kernel.org/r/20190805173404.GF136335@devbig004.ftw2.facebook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Jesper Dangaard Brouer says:
====================
net: fix regressions for generic-XDP
Thanks to Brandon Cazander, who wrote a very detailed bug report that
even used perf probe's on xdp-newbies mailing list, we discovered that
generic-XDP contains some regressions when using bpf_xdp_adjust_head().
First issue were that my selftests script, that use bpf_xdp_adjust_head(),
by mistake didn't use generic-XDP any-longer. That selftest should have
caught the real regression introduced in commit 458bf2f224f0 ("net: core:
support XDP generic on stacked devices.").
To verify this patchset fix the regressions, you can invoked manually via:
cd tools/testing/selftests/bpf/
sudo ./test_xdp_vlan_mode_generic.sh
sudo ./test_xdp_vlan_mode_native.sh
====================
Link: https://www.spinics.net/lists/xdp-newbies/msg01231.html
Fixes: 458bf2f224f0 ("net: core: support XDP generic on stacked devices.")
Reported by: Brandon Cazander <brandon.cazander@multapplied.net>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When generic-XDP was moved to a later processing step by commit
458bf2f224f0 ("net: core: support XDP generic on stacked devices.")
a regression was introduced when using bpf_xdp_adjust_head.
The issue is that after this commit the skb->network_header is now
changed prior to calling generic XDP and not after. Thus, if the header
is changed by XDP (via bpf_xdp_adjust_head), then skb->network_header
also need to be updated again. Fix by calling skb_reset_network_header().
Fixes: 458bf2f224f0 ("net: core: support XDP generic on stacked devices.")
Reported-by: Brandon Cazander <brandon.cazander@multapplied.net>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Given the increasing number of BPF selftests, it makes sense to
reduce the time to execute these tests. The ping parameters are
adjusted to reduce the time from measures 9 sec to approx 2.8 sec.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In-order to test both native-XDP (xdpdrv) and generic-XDP (xdpgeneric)
create two wrapper test scripts, that start the test_xdp_vlan.sh script
with these modes.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change BPF selftest test_xdp_vlan.sh to (default) use generic XDP.
This selftest was created together with a fix for generic XDP, in commit
297249569932 ("net: fix generic XDP to handle if eth header was
mangled"). And was suppose to catch if generic XDP was broken again.
The tests are using veth and assumed that veth driver didn't support
native driver XDP, thus it used the (ip link set) 'xdp' attach that fell
back to generic-XDP. But veth gained native-XDP support in 948d4f214fde
("veth: Add driver XDP"), which caused this test script to use
native-XDP.
Fixes: 948d4f214fde ("veth: Add driver XDP")
Fixes: 97396ff0bc2d ("selftests/bpf: add XDP selftests for modifying and popping VLAN headers")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 069d11465a80 ("net/mlx5e: RX, Enhance legacy Receive Queue
memory scheme") introduced an undefined behaviour below due to
"frag->last_in_page" is only initialized in mlx5e_init_frags_partition()
when,
if (next_frag.offset + frag_info[f].frag_stride > PAGE_SIZE)
or after bailed out the loop,
for (i = 0; i < mlx5_wq_cyc_get_size(&rq->wqe.wq); i++)
As the result, there could be some "frag" have uninitialized
value of "last_in_page".
Later, get_frag() obtains those "frag" and check "frag->last_in_page" in
mlx5e_put_rx_frag() and triggers the error during boot. Fix it by always
initializing "frag->last_in_page" to "false" in
mlx5e_init_frags_partition().
UBSAN: Undefined behaviour in
drivers/net/ethernet/mellanox/mlx5/core/en_rx.c:325:12
load of value 170 is not a valid value for type 'bool' (aka '_Bool')
Call trace:
dump_backtrace+0x0/0x264
show_stack+0x20/0x2c
dump_stack+0xb0/0x104
__ubsan_handle_load_invalid_value+0x104/0x128
mlx5e_handle_rx_cqe+0x8e8/0x12cc [mlx5_core]
mlx5e_poll_rx_cq+0xca8/0x1a94 [mlx5_core]
mlx5e_napi_poll+0x17c/0xa30 [mlx5_core]
net_rx_action+0x248/0x940
__do_softirq+0x350/0x7b8
irq_exit+0x200/0x26c
__handle_domain_irq+0xc8/0x128
gic_handle_irq+0x138/0x228
el1_irq+0xb8/0x140
arch_cpu_idle+0x1a4/0x348
do_idle+0x114/0x1b0
cpu_startup_entry+0x24/0x28
rest_init+0x1ac/0x1dc
arch_call_rest_init+0x10/0x18
start_kernel+0x4d4/0x57c
Fixes: 069d11465a80 ("net/mlx5e: RX, Enhance legacy Receive Queue memory scheme")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently init call of all actions (except ipt) init their 'parm'
structure as a direct pointer to nla data in skb. This leads to race
condition when some of the filter actions were initialized successfully
(and were assigned with idr action index that was written directly
into nla data), but then were deleted and retried (due to following
action module missing or classifier-initiated retry), in which case
action init code tries to insert action to idr with index that was
assigned on previous iteration. During retry the index can be reused
by another action that was inserted concurrently, which causes
unintended action sharing between filters.
To fix described race condition, save action idr index to temporary
stack-allocated variable instead on nla data.
Fixes: 0190c1d452a9 ("net: sched: atomically check-allocate action")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have to drop the adjust_link callback in order to finally migrate to
phylink.
Otherwise we get the following warning during startup:
"mv88e6xxx 2188000.ethernet-1:10: Using legacy PHYLIB callbacks. Please
migrate to PHYLINK!"
The warning is generated in the function dsa_port_link_register_of in
dsa/port.c:
int dsa_port_link_register_of(struct dsa_port *dp)
{
struct dsa_switch *ds = dp->ds;
if (!ds->ops->adjust_link)
return dsa_port_phylink_register(dp);
dev_warn(ds->dev,
"Using legacy PHYLIB callbacks. Please migrate to PHYLINK!\n");
[...]
}
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix two reset-gpio sanity checks which were never converted to use
gpio_is_valid(), and make sure to use -EINVAL to indicate a missing
reset line also for the UART-driver module parameter and for the USB
driver.
This specifically prevents the UART and USB drivers from incidentally
trying to request and use gpio 0, and also avoids triggering a WARN() in
gpio_to_desc() during probe when no valid reset line has been specified.
Fixes: e33a3f84f88f ("NFC: nfcmrvl: allow gpio 0 for reset signalling")
Reported-by: syzbot+cf35b76f35e068a1107f@syzkaller.appspotmail.com
Tested-by: syzbot+cf35b76f35e068a1107f@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The max9611 driver reads the die temperature at probe time to validate
the communication channel. Use the actual read value to perform the test
instead of the read function return value, which was mistakenly used so
far.
The temperature reading test was only successful because the 0 return
value is in the range of supported temperatures.
Fixes: 69780a3bbc0b ("iio: adc: Add Maxim max9611 ADC driver")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The fract1 word was not being properly programmed on the device leading
to wrong output frequencies.
Fixes: 7f699bd14913 (iio: frequency: adf4371: Add support for ADF4371 PLL)
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Stefan Popa <stefan.popa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Since every chip has a different whoami, we are not supporting all
existing variant of all chips. Add an explicit supported chips
list in Kconfig description.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This driver adds the initial support for the ON Semiconductor
NOA1305 Ambient Light Sensor.
Originally written by Sergei Miroshnichenko. Found here:
https://github.com/EmcraftSystems/linux-upstream/commit/196d6cf897e632d2cb82d45484bd7a1bfdd5b6d9
Signed-off-by: Sergei M <fizik1@yandex.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This patch corrects the SPDX License Identifier style
in header file related to STM32 Driver for I2C hardware
bus support.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Document the ON Semiconductor NOA1305 ambient light sensor devicetree
bindings.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Not even sure why it was there since the beginning. Just use IRQ
number in the sensor_data struct.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
in_accel_x_scale, in_accel_y_scale and in_accel_z_scale are always
the same. The scale is still defined to be in "info_mask_separate".
Userspace (iio-sensor-proxy and others) is not used to that and only
looks for "in_accel_scale" for the scaling factor to apply.
Change IIO_CHAN_INFO_SCALE from being separate in all channel to be
shared by type.
This removes in_accel_x_scale, in_accel_y_scale and in_accel_z_scale and
makes available in_accel_scale.
This is an ABI change, but hopefully in the 'no one will notice'
category. The cleanup in interface is worth the small risk that
there is a custom script out there somewhere that this will break.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use regulator_bulk_() APIs to shrink driver size.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Tested-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use devm_iio_device_register, which removes the tsl2772_remove
function.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Tested-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use devm_add_action_or_reset to call tsl2772_chip_off
when the device is removed.
This also fixes the issue that the chip is turned off
before the device is unregistered.
Not marked for stable as fairly hard to hit the bug and
this is in the middle of a set making other cleanups
to the driver. Hence will probably need explicit backporting.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Fixes: c06c4d793584 ("staging: iio: tsl2x7x/tsl2772: move out of staging")
Reviewed-by: Brian Masney <masneyb@onstation.org>
Tested-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Upon an error within proc_do_submiturb(), dec_usb_memory_use_count()
gets called once by the error handling tail and again by free_async().
Remove the first call.
Signed-off-by: Gavin Li <git@thegavinli.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190804235044.22327-1-gavinli@thegavinli.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
syzbot reported the following crash [0]:
BUG: KASAN: use-after-free in usb_free_coherent+0x79/0x80
drivers/usb/core/usb.c:928
Read of size 8 at addr ffff8881b18599c8 by task syz-executor.4/16007
CPU: 0 PID: 16007 Comm: syz-executor.4 Not tainted 5.3.0-rc2+ #23
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xca/0x13e lib/dump_stack.c:113
print_address_description+0x6a/0x32c mm/kasan/report.c:351
__kasan_report.cold+0x1a/0x33 mm/kasan/report.c:482
kasan_report+0xe/0x12 mm/kasan/common.c:612
usb_free_coherent+0x79/0x80 drivers/usb/core/usb.c:928
yurex_delete+0x138/0x330 drivers/usb/misc/yurex.c:100
kref_put include/linux/kref.h:65 [inline]
yurex_release+0x66/0x90 drivers/usb/misc/yurex.c:392
__fput+0x2d7/0x840 fs/file_table.c:280
task_work_run+0x13f/0x1c0 kernel/task_work.c:113
tracehook_notify_resume include/linux/tracehook.h:188 [inline]
exit_to_usermode_loop+0x1d2/0x200 arch/x86/entry/common.c:163
prepare_exit_to_usermode arch/x86/entry/common.c:194 [inline]
syscall_return_slowpath arch/x86/entry/common.c:274 [inline]
do_syscall_64+0x45f/0x580 arch/x86/entry/common.c:299
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x413511
Code: 75 14 b8 03 00 00 00 0f 05 48 3d 01 f0 ff ff 0f 83 04 1b 00 00 c3 48
83 ec 08 e8 0a fc ff ff 48 89 04 24 b8 03 00 00 00 0f 05 <48> 8b 3c 24 48
89 c2 e8 53 fc ff ff 48 89 d0 48 83 c4 08 48 3d 01
RSP: 002b:00007ffc424ea2e0 EFLAGS: 00000293 ORIG_RAX: 0000000000000003
RAX: 0000000000000000 RBX: 0000000000000007 RCX: 0000000000413511
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000006
RBP: 0000000000000001 R08: 0000000029a2fc22 R09: 0000000029a2fc26
R10: 00007ffc424ea3c0 R11: 0000000000000293 R12: 000000000075c9a0
R13: 000000000075c9a0 R14: 0000000000761938 R15: ffffffffffffffff
Allocated by task 2776:
save_stack+0x1b/0x80 mm/kasan/common.c:69
set_track mm/kasan/common.c:77 [inline]
__kasan_kmalloc mm/kasan/common.c:487 [inline]
__kasan_kmalloc.constprop.0+0xbf/0xd0 mm/kasan/common.c:460
kmalloc include/linux/slab.h:552 [inline]
kzalloc include/linux/slab.h:748 [inline]
usb_alloc_dev+0x51/0xf95 drivers/usb/core/usb.c:583
hub_port_connect drivers/usb/core/hub.c:5004 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5213 [inline]
port_event drivers/usb/core/hub.c:5359 [inline]
hub_event+0x15c0/0x3640 drivers/usb/core/hub.c:5441
process_one_work+0x92b/0x1530 kernel/workqueue.c:2269
worker_thread+0x96/0xe20 kernel/workqueue.c:2415
kthread+0x318/0x420 kernel/kthread.c:255
ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352
Freed by task 16007:
save_stack+0x1b/0x80 mm/kasan/common.c:69
set_track mm/kasan/common.c:77 [inline]
__kasan_slab_free+0x130/0x180 mm/kasan/common.c:449
slab_free_hook mm/slub.c:1423 [inline]
slab_free_freelist_hook mm/slub.c:1470 [inline]
slab_free mm/slub.c:3012 [inline]
kfree+0xe4/0x2f0 mm/slub.c:3953
device_release+0x71/0x200 drivers/base/core.c:1064
kobject_cleanup lib/kobject.c:693 [inline]
kobject_release lib/kobject.c:722 [inline]
kref_put include/linux/kref.h:65 [inline]
kobject_put+0x171/0x280 lib/kobject.c:739
put_device+0x1b/0x30 drivers/base/core.c:2213
usb_put_dev+0x1f/0x30 drivers/usb/core/usb.c:725
yurex_delete+0x40/0x330 drivers/usb/misc/yurex.c:95
kref_put include/linux/kref.h:65 [inline]
yurex_release+0x66/0x90 drivers/usb/misc/yurex.c:392
__fput+0x2d7/0x840 fs/file_table.c:280
task_work_run+0x13f/0x1c0 kernel/task_work.c:113
tracehook_notify_resume include/linux/tracehook.h:188 [inline]
exit_to_usermode_loop+0x1d2/0x200 arch/x86/entry/common.c:163
prepare_exit_to_usermode arch/x86/entry/common.c:194 [inline]
syscall_return_slowpath arch/x86/entry/common.c:274 [inline]
do_syscall_64+0x45f/0x580 arch/x86/entry/common.c:299
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at ffff8881b1859980
which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 72 bytes inside of
2048-byte region [ffff8881b1859980, ffff8881b185a180)
The buggy address belongs to the page:
page:ffffea0006c61600 refcount:1 mapcount:0 mapping:ffff8881da00c000
index:0x0 compound_mapcount: 0
flags: 0x200000000010200(slab|head)
raw: 0200000000010200 0000000000000000 0000000100000001 ffff8881da00c000
raw: 0000000000000000 00000000000f000f 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8881b1859880: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8881b1859900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
> ffff8881b1859980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8881b1859a00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8881b1859a80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
A quick look at the yurex_delete() shows that we drop the reference
to the usb_device before releasing any buffers associated with the
device. Delay the reference drop until we have finished the cleanup.
[0] https://lore.kernel.org/lkml/0000000000003f86d8058f0bd671@google.com/
Fixes: 6bc235a2e24a5e ("USB: add driver for Meywa-Denki & Kayac YUREX")
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: andreyknvl@google.com
Cc: gregkh@linuxfoundation.org
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: syzkaller-bugs@googlegroups.com
Cc: dtor@chromium.org
Reported-by: syzbot+d1fedb1c1fdb07fca507@syzkaller.appspotmail.com
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190805111528.6758-1-suzuki.poulose@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use devm_add_action_or_reset to remove the call to
tsl2772_disable_regulators_action to simplify the error path.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Tested-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
As kmemdup API does kmalloc + memcpy . We can make use of it instead of
calling kmalloc and memcpy independetly.
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Link: https://lore.kernel.org/r/20190804024832.GA14352@hari-Inspiron-1545
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add spaces around '-', '+', '&','|' and '?' to improve readability
and follow kernel coding style in rtw_ap.c
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Link: https://lore.kernel.org/r/20190803192551.GA24041@saurav
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove Unnecessary parentheses around padapter->mlmepriv,
pmlmeext->mlmext_info and pmlmeinfo->network in rtw_ap.c
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Link: https://lore.kernel.org/r/20190803184750.GA23507@saurav
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Correct spelling mistake in rtw_ap.c
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Link: https://lore.kernel.org/r/20190803183051.GA23151@saurav
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
rtw_efuse.c
Add spaces around '-', '+', '>>','<<' and '*' to improve readability
and follow kernel coding style.
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Link: https://lore.kernel.org/r/20190803131839.GA14077@saurav
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: linux-iio@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use device-managed APIs to simplify the code.
The remove functions are redundant now and can
be deleted.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This patch is trying to cleanup for good the buffers operation functions.
There is no need of using preenable, all can be done into
postenable. Let's also use logical sequence of operations as
already done in accel driver.
Finally also rename the goto label using operation to perform and not
where it fails.
Not stable material as not fixing a 'bug' but rather bringing the
driver in line with general 'patterns' to allow a subsystem wide
cleanup.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This patch is trying to cleanup for good the buffers operation functions.
Let's rename the goto label using operation to perform and not
where it fails.
Not stable material as not fixing a 'bug' but rather bringing the
driver in line with general 'patterns' to allow a subsystem wide
cleanup.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This patch is trying to cleanup for good the buffers operation functions.
There is no need of using preenable, all can be done into
postenable. Let's also use logical sequence of operations as
already done in accel driver.
Finally also rename the goto label using operation to perform and not
where it fails.
Not stable material as not fixing a 'bug' but rather bringing the
driver in line with general 'patterns' to allow a subsystem wide
cleanup.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This patch is trying to cleanup for good the buffers operation functions.
There is no need of using preenable, all can be done into
postenable.
Let's also rename the goto label using operation to perform and not
where it fails.
Note, not stable material. This is cleaning up the logic flow rather
than fixing a bug.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Since commit commit 328e56647944 ("KVM: arm/arm64: vgic: Defer
touching GICH_VMCR to vcpu_load/put"), we leave ICH_VMCR_EL2 (or
its GICv2 equivalent) loaded as long as we can, only syncing it
back when we're scheduled out.
There is a small snag with that though: kvm_vgic_vcpu_pending_irq(),
which is indirectly called from kvm_vcpu_check_block(), needs to
evaluate the guest's view of ICC_PMR_EL1. At the point were we
call kvm_vcpu_check_block(), the vcpu is still loaded, and whatever
changes to PMR is not visible in memory until we do a vcpu_put().
Things go really south if the guest does the following:
mov x0, #0 // or any small value masking interrupts
msr ICC_PMR_EL1, x0
[vcpu preempted, then rescheduled, VMCR sampled]
mov x0, #ff // allow all interrupts
msr ICC_PMR_EL1, x0
wfi // traps to EL2, so samping of VMCR
[interrupt arrives just after WFI]
Here, the hypervisor's view of PMR is zero, while the guest has enabled
its interrupts. kvm_vgic_vcpu_pending_irq() will then say that no
interrupts are pending (despite an interrupt being received) and we'll
block for no reason. If the guest doesn't have a periodic interrupt
firing once it has blocked, it will stay there forever.
To avoid this unfortuante situation, let's resync VMCR from
kvm_arch_vcpu_blocking(), ensuring that a following kvm_vcpu_check_block()
will observe the latest value of PMR.
This has been found by booting an arm64 Linux guest with the pseudo NMI
feature, and thus using interrupt priorities to mask interrupts instead
of the usual PSTATE masking.
Cc: stable@vger.kernel.org # 4.12
Fixes: 328e56647944 ("KVM: arm/arm64: vgic: Defer touching GICH_VMCR to vcpu_load/put")
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
