| Age | Commit message (Collapse) | Author |
|---|
|
Fix the below crash on Book3E 64. pgtable_page_dtor expects struct
page *arg.
Also call the destructor on non book3s platforms correctly. This frees
up the split PTL locks correctly if we had allocated them before.
Call Trace:
.kmem_cache_free+0x9c/0x44c (unreliable)
.ptlock_free+0x1c/0x30
.tlb_remove_table+0xdc/0x224
.free_pgd_range+0x298/0x500
.shift_arg_pages+0x10c/0x1e0
.setup_arg_pages+0x200/0x25c
.load_elf_binary+0x450/0x16c8
.search_binary_handler.part.11+0x9c/0x248
.do_execveat_common.isra.13+0x868/0xc18
.run_init_process+0x34/0x4c
.try_to_run_init_process+0x1c/0x68
.kernel_init+0xdc/0x130
.ret_from_kernel_thread+0x58/0x7c
Fixes: 702346768 ("powerpc/mm/nohash: Remove pte fragment dependency from nohash")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
In commit eae5f709a4d7 ("powerpc: Add __printf verification to
prom_printf") __printf attribute was added to prom_printf(), which
means GCC started warning about type/format mismatches. As part of
that commit we changed some "%lx" formats to "%llx" where the type is
actually unsigned long long.
Unfortunately prom_printf() doesn't know how to print "%llx", it just
prints a literal "lx", eg:
reserved memory map:
lx - lx
lx - lx
prom_printf() also doesn't know how to print "%u" (only "%lu"), it
just prints a literal "u", eg:
Max number of cores passed to firmware: u (NR_CPUS = 2048)
Instead of:
Max number of cores passed to firmware: 2048 (NR_CPUS = 2048)
This commit adds support for the missing formatters.
Fixes: eae5f709a4d7 ("powerpc: Add __printf verification to prom_printf")
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
APC virtual machines arent used on POWER-9 chips and are already
disabled in on-chip CAPP. They also need to be disabled on the PSL via
'PSL Data Send Control Register' by setting bit(47). This forces the
PSL to send commands to CAPP with queue.id == 0.
Fixes: 5632874311db ("cxl: Add support for POWER9 DD2")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Currently we see a kernel-oops reported on Power-9 while attaching a
context to an AFU, with radix-mode and sysfs attr 'prefault_mode' set
to anything other than 'none'. The backtrace of the oops is of this
form:
Unable to handle kernel paging request for data at address 0x00000080
Faulting instruction address: 0xc00800000bcf3b20
cpu 0x1: Vector: 300 (Data Access) at [c00000037f003800]
pc: c00800000bcf3b20: cxl_load_segment+0x178/0x290 [cxl]
lr: c00800000bcf39f0: cxl_load_segment+0x48/0x290 [cxl]
sp: c00000037f003a80
msr: 9000000000009033
dar: 80
dsisr: 40000000
current = 0xc00000037f280000
paca = 0xc0000003ffffe600 softe: 3 irq_happened: 0x01
pid = 3529, comm = afp_no_int
<snip>
cxl_prefault+0xfc/0x248 [cxl]
process_element_entry_psl9+0xd8/0x1a0 [cxl]
cxl_attach_dedicated_process_psl9+0x44/0x130 [cxl]
native_attach_process+0xc0/0x130 [cxl]
afu_ioctl+0x3f4/0x5e0 [cxl]
do_vfs_ioctl+0xdc/0x890
ksys_ioctl+0x68/0xf0
sys_ioctl+0x40/0xa0
system_call+0x58/0x6c
The issue is caused as on Power-8 the AFU attr 'prefault_mode' was
used to improve initial storage fault performance by prefaulting
process segments. However on Power-9 with radix mode we don't have
Storage-Segments that we can prefault. Also prefaulting process Pages
will be too costly and fine-grained.
Hence, since the prefaulting mechanism doesn't makes sense of
radix-mode, this patch updates prefault_mode_store() to not allow any
other value apart from CXL_PREFAULT_NONE when radix mode is enabled.
Fixes: f24be42aab37 ("cxl: Add psl9 specific code")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
sound/pci/hda/local.h seems to be an earlier version of
sound/hda/local.h; it was added at the same time but doesn't seem to
have ever been used (within the git history). Most of its macros
depend on a hdac_read_parm() function which is not defined anywhere.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
As the mvpp2 driver is growing, move this driver to a dedicated
directory and split it into several files.
Since this driver has a lot of register defines and structure
definitions, it can benefit from having all of this into a dedicated
header file, named mvpp2.h.
A good chunk of the mvpp2 code is dedicated to Header Parser handling, so
we introduce mvpp2_prs.h where all Header Parser definitions are located,
and mvpp2_prs.c containing the related code.
In the same way, mvpp2_cls.h and mvpp2_cls.c are created to contain
Classifier and RSS related code.
The former 'mvpp2.c' file is renamed 'mvpp2_main.c' so that we can keep
the driver binary named 'mvpp2'.
This commit is only about spliting the driver into multiple files and
doesn't introduce any new function, feature or fix besides removing
'static' keywords when needed.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All callers of zap_vma_ptes() are not interested in the return value of
that function, so let's simplify its interface and drop the return
value.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
There is no need to check return value of zap_vma_ptes()
because there is nothing to do with this knowledge.
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The failure reported by zap_vma_ptes() means that wrong VMA pages
were supplied, however it is impossible for this type of address.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
There is no need to check return value of zap_vma_ptes()
because there is nothing to do with this knowledge.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Let's perform checks in-place instead of BUG_ONs.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
There is no need to check existence of mad_queue, because we already did
pointer dereference before call to dequeue_mad().
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
There is no need to bring down the whole machine, just because unknown
event was received. It is better to ignore it silently.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
In case CM work list is empty, the work pointer will be NULL,
so instead of kernel crash it is better to abort processing
of works.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
cxgb3 driver properly handles errors returned by IDR, so there is no
need to have special case (kernel crash) just because IDR is full.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
There is no need to crash the machine if unknown work request was
received in SQP MAD.
Cc: <stable@vger.kernel.org> # 3.6
Fixes: 37bfc7c1e83f ("IB/mlx4: SR-IOV multiplex and demultiplex MADs")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Any steering QP is supposed be above steering_qp_base,
see function mlx4_ib_steer_qp_alloc() for it, however in case
of misalignment between SW and FW, this qp_base can be wrong.
Use WARN() to catch such situation without killing the machine.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This patch adds support for the BCM5389 switch connected through MDIO.
Signed-off-by: Damien Thébault <damien.thebault@vitec.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tc_ctl_tfilter handles three netlink message types: RTM_NEWTFILTER,
RTM_DELTFILTER, RTM_GETTFILTER. However, implementation of this function
involves a lot of branching on specific message type because most of the
code is message-specific. This significantly complicates adding new
functionality and doesn't provide much benefit of code reuse.
Split tc_ctl_tfilter to three standalone functions that handle filter new,
delete and get requests.
The only truly protocol independent part of tc_ctl_tfilter is code that
looks up queue, class, and block. Refactor this code to standalone
tcf_block_find function that is used by all three new handlers.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pblk allocates line bitmaps within the line lock unnecessarily. In order
to take pressure out of the fast patch, allocate line bitmaps outside
of this lock and refactor accordingly.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Unless we kick the writer directly when setting a new flush point, the
user risks having to wait for up to one second (the default timeout for
the write thread to be kicked) for the IO to complete.
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When switching between different lun configurations, there is no
guarantee that all lines that contain closed/open chunks have some
valid data to recover.
Check that the smeta chunk has been written to instead. Also
skip bad lines (that does not have enough good chunks).
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In the read path, pblk gets a reference to the incoming bio and puts it
after ending the bio. Though this behavior is correct, it is unnecessary
since pblk is the one putting the bio, therefore, it cannot disappear
underneath it.
Removing this reference, allows to clean up rqd->bio and avoids pointer
bouncing for the different read paths. Now, the incoming bio always
resides in the read context and pblk's internal bios (if any) reside in
rqd->bio.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In some cases, users can want set write buffer size manually, e.g. to
adjust it to specific workload. This patch provides the possibility
to set write buffer size via module parameter feature.
Signed-off-by: Marcin Dziegielewski <marcin.dziegielewski@intel.com>
Signed-off-by: Igor Konopko <igor.j.konopko@intel.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When error occurs during bio_add_page on partial read path, pblk
tries to free pages twice.
Signed-off-by: Igor Konopko <igor.j.konopko@intel.com>
Signed-off-by: Marcin Dziegielewski <marcin.dziegielewski@intel.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Currently in case of error caused by bio_pc_add_page in
pblk_bio_add_pages two issues occur when calling from
pblk_rb_read_to_bio(). First one is in pblk_bio_free_pages, since we
are trying to free pages not allocated from our mempool. Second one
is the warn from dma_pool_free, that we are trying to free NULL
pointer dma.
This commit fix both issues.
Signed-off-by: Igor Konopko <igor.j.konopko@intel.com>
Signed-off-by: Marcin Dziegielewski <marcin.dziegielewski@intel.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Smeta write errors were previously ignored. Skip these
lines instead and throw them back on the free
list, so the chunks will go through a reset cycle
before we attempt to use the line again.
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Write failures should not happen under normal circumstances,
so in order to bring the chunk back into a known state as soon
as possible, evacuate all the valid data out of the line and let the
fw judge if the block can be written to in the next reset cycle.
Do this by introducing a new gc list for lines with failed writes,
and ensure that the rate limiter allocates a small portion of
the write bandwidth to get the job done.
The lba list is saved in memory for use during gc as we
cannot gurantee that the emeta data is readable if a write
error occurred.
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The write error recovery path is incomplete, so rework
the write error recovery handling to do resubmits directly
from the write buffer.
When a write error occurs, the remaining sectors in the chunk are
mapped out and invalidated and the request inserted in a resubmit list.
The writer thread checks if there are any requests to resubmit,
scans and invalidates any lbas that have been overwritten by later
writes and resubmits the failed entries.
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Stateful CPU architecture extensions may require the signal frame
to grow to a size that exceeds the arch's MINSIGSTKSZ #define.
However, changing this #define is an ABI break.
To allow userspace the option of determining the signal frame size
in a more forwards-compatible way, this patch adds a new auxv entry
tagged with AT_MINSIGSTKSZ, which provides the maximum signal frame
size that the process can observe during its lifetime.
If AT_MINSIGSTKSZ is absent from the aux vector, the caller can
assume that the MINSIGSTKSZ #define is sufficient. This allows for
a consistent interface with older kernels that do not provide
AT_MINSIGSTKSZ.
The idea is that libc could expose this via sysconf() or some
similar mechanism.
There is deliberately no AT_SIGSTKSZ. The kernel knows nothing
about userspace's own stack overheads and should not pretend to
know.
For arm64:
The primary motivation for this interface is the Scalable Vector
Extension, which can require at least 4KB or so of extra space
in the signal frame for the largest hardware implementations.
To determine the correct value, a "Christmas tree" mode (via the
add_all argument) is added to setup_sigframe_layout(), to simulate
addition of all possible records to the signal frame at maximum
possible size.
If this procedure goes wrong somehow, resulting in a stupidly large
frame layout and hence failure of sigframe_alloc() to allocate a
record to the frame, then this is indicative of a kernel bug. In
this case, we WARN() and no attempt is made to populate
AT_MINSIGSTKSZ for userspace.
For arm64 SVE:
The SVE context block in the signal frame needs to be considered
too when computing the maximum possible signal frame size.
Because the size of this block depends on the vector length, this
patch computes the size based not on the thread's current vector
length but instead on the maximum possible vector length: this
determines the maximum size of SVE context block that can be
observed in any signal frame for the lifetime of the process.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Now that the kernel SVE support is reasonably mature, it is
excessive to default sve_max_vl to the invalid value -1 and then
sprinkle WARN_ON()s around the place to make sure it has been
initialised before use. The cpufeatures code already runs pretty
early, and will ensure sve_max_vl gets initialised.
This patch initialises sve_max_vl to something sane that will be
supported by every SVE implementation, and removes most of the
sanity checks.
The checks in find_supported_vector_length() are retained for now.
If anything goes horribly wrong, we are likely to trip a check here
sooner or later.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Lenovo Zhaoyang E42-80 is another Lenovo model without a hw rfkill switch,
resulting in wifi always reported as hard blocked.
Add the model to the list of models without rfkill switch.
Signed-off-by: dylanchu <chdy.uuid@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Add touchscreen info for the Onda V891w 8.9" windows tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
This commit adds the necessary device-properties to make the touchscreen
on Point of View mobii TAB-P800W (v2.0) tablets work.
Note that we already have an entry for the Point of View mobii
TAB-P800W (v2.1), that version uses a different digitizer and different
firmware, so the v2.0 version needs its own entry.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Add touchscreen info for the Jumper EZpad 6 Pro.
Cc: zy <574249312@qq.com>
Reported-and-tested-by: zy <574249312@qq.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
This reverts commit 13b40935cf64f59b93cf1c716a2033488e5a228c.
This was a workaround for a bug in the HDA driver that prevented
the HDA audio chip from going into runtime pm which prevented
the GPU from going into runtime pm.
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=106597
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The comparison with the number of elements in array df_v3_7_channel_number
is off-by-one and can produce an array out-of-bounds read if
fb_channel_number is equal to the number of elements of the array. Fix
this by changing the comparison to >= instead of >.
Detected by CoverityScan, CID#1469489 ("Out-of-bounds read")
Fixes: 13b581502d51 ("drm/amdgpu/df: implement df v3_6 callback functions (v2)")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
In rtnl_newlink(), NULL check is performed on m_ops however member of
ops is accessed. Fixed by accessing member of m_ops instead of ops.
[ 345.432629] BUG: KASAN: null-ptr-deref in rtnl_newlink+0x400/0x1110
[ 345.432629] Read of size 4 at addr 0000000000000088 by task ip/986
[ 345.432629]
[ 345.432629] CPU: 1 PID: 986 Comm: ip Not tainted 4.17.0-rc6+ #9
[ 345.432629] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
[ 345.432629] Call Trace:
[ 345.432629] dump_stack+0xc6/0x150
[ 345.432629] ? dump_stack_print_info.cold.0+0x1b/0x1b
[ 345.432629] ? kasan_report+0xb4/0x410
[ 345.432629] kasan_report.cold.4+0x8f/0x91
[ 345.432629] ? rtnl_newlink+0x400/0x1110
[ 345.432629] rtnl_newlink+0x400/0x1110
[...]
Fixes: ccf8dbcd062a ("rtnetlink: Remove VLA usage")
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
(resend for properly queueing in patchwork)
kcm_clone() creates kernel socket, which does not take net counter.
Thus, the net may die before the socket is completely destructed,
i.e. kcm_exit_net() is executed before kcm_done().
Reported-by: syzbot+5f1a04e374a635efc426@syzkaller.appspotmail.com
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since header_preamble_size is 0 for SMB2+ we can remove it in those
code paths that are only invoked from SMB2.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
struct smb2_hdr is now just a wrapper for smb2_sync_hdr.
We can thus get rid of smb2_hdr completely and access the sync header directly.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
expiry, status STATUS_NETWORK_SESSION_EXPIRED, however the server can also respond with STATUS_USER_SESSION_DELETED in cases where the session has been idle for some time and the server reaps the session to recover resources.
Handle this additional status in the same way as SESSION_EXPIRED.
Signed-off-by: Mark Syms <mark.syms@citrix.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
|
|
Remove dead function for manual sync. I/O
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If the namespace is unregistered before the LightNVM target is removed
(e.g., on hot unplug) it is too late for the target to store any metadata
on the device - any attempt to write to the device will fail. In this
case, pass on a "gracefull teardown" flag to the target to let it know
when this happens.
In the case of pblk, we pad the open line (close all open chunks) to
improve data retention. In the event of an ungraceful shutdown, avoid
this part and just clean up.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Do the check for the chunk state after making sure that the chunk type
is supported.
Fixes: 32ef9412c114 ("lightnvm: pblk: implement get log report chunk")
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Remove unnecessary argument on pblk_line_free()
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Call nvm_submit_io directly and remove an unnecessary indirection on the
read path.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Return a meaningful error when the sanity vector I/O check fails.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When cleaning up buffer entries as we wrap up, their state should be
"completed". If any of the entries is in "submitted" state, it means
that something bad has happened. Trigger a warning immediately instead of
waiting for the state flag to eventually be updated, thus hiding the
issue.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In the event of a mismatch between the read LBA and the metadata pointer
reported by the device, improve the error message to be able to detect
the offending physical address (PPA) mapped to the corrupted LBA.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
