| Age | Commit message (Collapse) | Author |
|---|
|
Add a 'continuous' option for usb charging which enables
the "linear" charging mode of the twl4030.
Linear charging does a good job with not-so-reliable power sources.
Auto mode does not work well as it switches off when voltage drops
momentarily. Care must be taken not to over-charge.
It was used with a bike hub dynamo since a year or so. In that case
there are automatically charging stops when the cyclist needs a break.
Original-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
'off' or 'auto' to
/sys/class/power/twl4030_usb/mode
will now enable or disable charging from USB port. Normally this is
enabled on 'plug' and disabled on 'unplug'.
Unplug will still disable charging. 'plug' will only enable it if
'auto' if selected.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
'max_current' sysfs attributes are created which allow the
max to be set.
Whenever a current source changes, the default is restored.
This will be followed by a uevent, so user-space can decide to
update again.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
The twl4030 charger has two current sources, 'USB' and 'AC'
(presumably "Accessory Charger" because it isn't Alternating Current).
If 'AC' is providing current, we should set the current limit
differently to when it isn't (and so USB is used).
So split 'cur' into 'usb_cur' and 'ac_cur' and use accordingly.
Now we must review the current setting on any interrupt or USB
event which might indicate that the charger-source has changed.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
The twl4030 allows control of the incoming current.
Part of this control is a 'CGAIN' setting which doubles
the range for half the precision. This control affects
several different current setting, so all need to be updated
at once when CGAIN is changed.
With this patch, all of these current setting are managed
by the driver, but most are left at their default settings.
The current drawn is set to 500mA if the allow_usb module parameter is
set, and to 100mA otherwise.
More fine control will appear in later patches.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
We will need this calculation in other places, so
create functions to map between register value and uA value.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
The usb phy driver already determines when VBUS is available,
so repeating the test in the charger driver is pointless duplication.
On probe, process the last event from the phy, and from then on,
do whatever the phy tells us without double-checking.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Now that twl4030_bci_probe can safely return -EPROBE_DEFER,
do so when devm_usb_get_phy_by_node returns that error.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Drivers using module_platform_driver_probe cannot return
EPROBE_DEFER from the probe function, which makes them rather useless
these days...
Convert to module_platform_driver() so EPROBE_DEFER can be used.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
The twl4030 usb phy needs to be active while we are using
the USB VBUS as a current source for charging.
In particular, the usb3v1 regulator must be enabled and the
PHY_PWR_PHYPWD bit must be set to keep the phy powered.
commit ab37813f4093a5f59cb8e083cde277289dc72ed3
twl4030_charger: Allow charger to control the regulator that feeds it
gave the charger control over the regulator, but didn't resolve
the PHY_PWR_PHYPWD issue.
Now that both of these are controlled by runtime_pm in
phy-twl4030-usb, we can simply take a runtime_pm reference to the USB
phy whenever the charger wants to use it as a current source.
So this patch reverts the above commit, and adds the necessary
runtime_pm calls.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
'pci/virtualization' into next
* pci/irq:
PCI/MSI: Free legacy IRQ when enabling MSI/MSI-X
PCI: Add helpers to manage pci_dev->irq and pci_dev->irq_managed
PCI, x86: Implement pcibios_alloc_irq() and pcibios_free_irq()
PCI: Add pcibios_alloc_irq() and pcibios_free_irq()
* pci/misc:
PCI: Remove unused "pci_probe" flags
PCI: Add VPD function 0 quirk for Intel Ethernet devices
PCI: Add dev_flags bit to access VPD through function 0
PCI / ACPI: Fix pci_acpi_optimize_delay() comment
PCI: Remove a broken link in quirks.c
PCI: Remove useless redundant code
PCI: Simplify pci_find_(ext_)capability() return value checks
PCI: Move PCI_FIND_CAP_TTL to pci.h and use it in quirks
PCI: Add pcie_downstream_port() (true for Root and Switch Downstream Ports)
PCI: Fix pcie_port_device_resume() comment
PCI: Shift PCI_CLASS_NOT_DEFINED consistently with other classes
PCI: Revert aeb30016fec3 ("PCI: add Intel USB specific reset method")
PCI: Fix TI816X class code quirk
PCI: Fix generic NCR 53c810 class code quirk
PCI: Use PCI_CLASS_SERIAL_USB instead of bare number
PCI: Add quirk for Intersil/Techwell TW686[4589] AV capture cards
PCI: Remove Intel Cherrytrail D3 delays
* pci/resource:
PCI: Call pci_read_bridge_bases() from core instead of arch code
* pci/virtualization:
PCI: Restore ACS configuration as part of pci_restore_state()
|
|
into next
* pci/host-designware:
PCI: designware: Don't complain missing *config* reg space if va_cfg0 is set
* pci/host-xgene:
PCI: xgene: Add support for a 64-bit prefetchable memory window
arm64: dts: Add APM X-Gene PCIe 64-bit prefetchable window
PCI: xgene: Drop owner assignment from platform_driver
* pci/host-xilinx:
PCI: xilinx: Check for MSI interrupt flag before handling as INTx
|
|
Without this initialization, gateways which actually announce up/down
bandwidth of 0/0 could be added. If these nodes get purged via
_batadv_purge_orig() later, the gw_node structure does not get removed
since batadv_gw_node_delete() updates the gw_node with up/down
bandwidth of 0/0, and the updating function then discards the change
and does not free gw_node.
This results in leaking the gw_node structures, which references other
structures: gw_node -> orig_node -> orig_node_ifinfo -> hardif. When
removing the interface later, the open reference on the hardif may cause
hangs with the infamous "unregister_netdevice: waiting for mesh1 to
become free. Usage count = 1" message.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
The tt_local_entry deletion performed in batadv_tt_local_remove() was neither
protecting against simultaneous deletes nor checking whether the element was
still part of the list before calling hlist_del_rcu().
Replacing the hlist_del_rcu() call with batadv_hash_remove() provides adequate
protection via hash spinlocks as well as an is-element-still-in-hash check to
avoid 'blind' hash removal.
Fixes: 068ee6e204e1 ("batman-adv: roaming handling mechanism redesign")
Reported-by: alfonsname@web.de
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
batadv_softif_vlan_get() may return NULL which has to be verified
by the caller.
Fixes: 35df3b298fc8 ("batman-adv: fix TT VLAN inconsistency on VLAN re-add")
Reported-by: Ryan Thompson <ryan@eero.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
When a node running DAT receives an ARP request from the LAN for the
first time, it is likely that this node will request the ARP entry
through the distributed ARP table (DAT) in the mesh.
Once a DAT reply is received the asking node must check if the MAC
address for which the IP address has been asked is local. If it is, the
node must drop the ARP reply bceause the client should have replied on
its own locally.
Forwarding this reply means fooling any L2 bridge (e.g. Ethernet
switches) lying between the batman-adv node and the LAN. This happens
because the L2 bridge will think that the client sending the ARP reply
lies somewhere in the mesh, while this node is sitting in the same LAN.
Reported-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
If a GPIO driver uses gpiochip_add_pin_range() (which is usually the
case for GPIO/PFC combos), the GPIO hogging mechanism configured from DT
doesn't work:
requesting hog GPIO led1-high (chip sh73a0_pfc, offset 20) failed
The actual error code is -517 == -EPROBE_DEFER.
The problem is that PFC+GPIO registration is handled in multiple steps:
1. pinctrl_register(),
2. gpiochip_add(),
3. gpiochip_add_pin_range().
Configuration of the hogs is handled in gpiochip_add():
gpiochip_add
of_gpiochip_add
of_gpiochip_scan_hogs
gpiod_hog
gpiochip_request_own_desc
__gpiod_request
chip->request
pinctrl_request_gpio
pinctrl_get_device_gpio_range
However, at this point the GPIO controller hasn't been added to
pinctrldev_list yet, so the range can't be found, and the operation fails
with -EPROBE_DEFER.
To fix this, add a "gpio-ranges" property to the gpio device node, so
the ranges are added by of_gpiochip_add_pin_range(), which is called by
of_gpiochip_add() before the call to of_gpiochip_scan_hogs().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
If a GPIO driver uses gpiochip_add_pin_range() (which is usually the
case for GPIO/PFC combos), the GPIO hogging mechanism configured from DT
doesn't work:
requesting hog GPIO lcd0 (chip r8a7740_pfc, offset 176) failed
The actual error code is -517 == -EPROBE_DEFER.
The problem is that PFC+GPIO registration is handled in multiple steps:
1. pinctrl_register(),
2. gpiochip_add(),
3. gpiochip_add_pin_range().
Configuration of the hogs is handled in gpiochip_add():
gpiochip_add
of_gpiochip_add
of_gpiochip_scan_hogs
gpiod_hog
gpiochip_request_own_desc
__gpiod_request
chip->request
pinctrl_request_gpio
pinctrl_get_device_gpio_range
However, at this point the GPIO controller hasn't been added to
pinctrldev_list yet, so the range can't be found, and the operation fails
with -EPROBE_DEFER.
To fix this, add a "gpio-ranges" property to the gpio device node, so
the range is added by of_gpiochip_add_pin_range(), which is called by
of_gpiochip_add() before the call to of_gpiochip_scan_hogs().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
If a GPIO driver uses gpiochip_add_pin_range() (which is usually the
case for GPIO/PFC combos), the GPIO hogging mechanism configured from DT
doesn't work:
requesting hog GPIO led1-high (chip r8a73a4_pfc, offset 28) failed
The actual error code is -517 == -EPROBE_DEFER.
The problem is that PFC+GPIO registration is handled in multiple steps:
1. pinctrl_register(),
2. gpiochip_add(),
3. gpiochip_add_pin_range().
Configuration of the hogs is handled in gpiochip_add():
gpiochip_add
of_gpiochip_add
of_gpiochip_scan_hogs
gpiod_hog
gpiochip_request_own_desc
__gpiod_request
chip->request
pinctrl_request_gpio
pinctrl_get_device_gpio_range
However, at this point the GPIO controller hasn't been added to
pinctrldev_list yet, so the range can't be found, and the operation fails
with -EPROBE_DEFER.
To fix this, add a "gpio-ranges" property to the gpio device node, so
the ranges are added by of_gpiochip_add_pin_range(), which is called by
of_gpiochip_add() before the call to of_gpiochip_scan_hogs().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
spfi_setup may be called many times by the spi framework, but
gpio_request_one can only be called once without freeing, repeatedly
calling gpio_request_one will cause an error to be thrown, which
causes the request to spi_setup to be marked as failed.
We can have a per-spi_device flag that indicates whether or not the
gpio has been requested. If the gpio has already been requested use
gpio_direction_output to set the direction of the gpio.
Fixes: 8c2c8c03cdcb ("spi: img-spfi: Control CS lines with GPIO")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
This allows the module to be autoloaded.
Together with 07949bf9c63c ("cpufreq: dt: allow driver to boot
automatically") this is sufficient to allow a modular kernel (such
as Debian's) to enable cpufreq on a Cubietruck.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
As function ep_matches() is used to match endpoint with usb descriptor it's
highly unintuitive that it modifies endpoint and descriptor structures fields.
This patch moves code configuring ep and desc from ep_matches() to
usb_ep_autoconfig_ss(), so now function ep_matches() does nothing more than
its name suggests.
[ balbi@ti.com : fix build warning ]
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The same effect can be achieved by using capabilities flags, so now we can
get rid of handling of hardware specific limitations in generic code.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Introduce endpoint matching mechanism basing on endpoint capabilities
flags. We check if endpoint supports transfer type and direction requested
in ep descriptor. Since we have this new endpoint matching mechanism
there is no need to have old code guessing endpoint capabilities basing
on its name, so we are getting rid of it. Remove also the obsolete comment.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
