| Age | Commit message (Collapse) | Author |
|---|
|
The previous diolan adapter uses other out/in endpoints than
the current DLN-2-U2C in compatibility mode.
They changed from 0x2/0x84 to 0x3/0x83.
This patch gets the endpoints from the usb interface, instead
of hardcode them in the driver.
This was tested on a current DLN-2-U2C board.
Signed-off-by: Martin Vogt <mvogt1@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Use bus->power_keep_link_on instead. The controller shouldn't go to
D3 when the link isn't reset, so essentially avoiding the link reset
means avoiding the runtime PM.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Set the missing pcbeep default amp for ALC668.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
It's compatible with ALC269.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
I2C IP block expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.
Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
When booting Nokia N900 smartphone with v3.12 + omap2plus_defconfig
(LOCKDEP enabled) and CONFIG_DISPLAY_PANEL_SONY_ACX565AKM enabled,
the following BUG is seen during the boot:
[ 7.302154] =====================================
[ 7.307128] [ BUG: bad unlock balance detected! ]
[ 7.312103] 3.12.0-los.git-2093492-00120-g5e01dc7 #3 Not tainted
[ 7.318450] -------------------------------------
[ 7.323425] kworker/u2:1/12 is trying to release lock (&ddata->mutex) at:
[ 7.330657] [<c031b760>] acx565akm_enable+0x12c/0x18c
[ 7.335998] but there are no more locks to release!
Fix by removing double unlock and handling the locking completely inside
acx565akm_panel_power_on() when doing the power on.
Reported-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
MFD_AS3722 can only be builtin, so it needs I2C builtin as well.
With I2C=m, we get:
drivers/mfd/as3722.c:372: undefined reference to `devm_regmap_init_i2c'
drivers/built-in.o: In function `as3722_i2c_driver_init':
drivers/mfd/as3722.c:444: undefined reference to `i2c_register_driver'
drivers/built-in.o: In function `as3722_i2c_driver_exit':
drivers/mfd/as3722.c:444: undefined reference to `i2c_del_driver'
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
(edev->extcon_dev_type.groups) has been freed before device_unregister.
extcon_dev_unregister -> kfree(edev->extcon_dev_type.groups)
then device_unregister -> device_del -> device_remove_attrs
-> device_remove_groups(dev, type->groups);
panic because type->groups has been freed.
This patch is move device_unregister ahead of groups free
to avoid panic in extcon_dev_unregister.
stack
[ 22.847226] BUG: unable to handle kernel paging request at 5f39746e
[ 22.847234] IP: [<c1387fcd>] sysfs_remove_group+0x2d/0xd0
[ 22.847238] *pdpt = 0000000000000000 *pde = 0000000000000000
[ 22.847241] Oops: 0000 [#1] PREEMPT SMP
[ 22.847244] Modules linked in:
[ 22.847249] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 3.10.16-261140-g6533774 #1
[ 22.847251] task: f3078000 ti: f3072000 task.ti: f3072000
[ 22.847254] EIP: 0060:[<c1387fcd>] EFLAGS: 00010206 CPU: 0
[ 22.847257] EIP is at sysfs_remove_group+0x2d/0xd0
[ 22.847259] EAX: 00000004 EBX: 5f39746e ECX: 00000000 EDX: f2773560
[ 22.847261] ESI: f2653b80 EDI: f2773560 EBP: f3073c90 ESP: f3073c70
[ 22.847263] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[ 22.847264] CR0: 8005003b CR2: 5f39746e CR3: 020e5000 CR4: 001007f0
[ 22.847266] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[ 22.847268] DR6: ffff0ff0 DR7: 00000400
[ 22.847269] Stack:
[ 22.847276] c13848c9 c1ae3805 f3073c80 f24ddc4c 00000246 f2773e88 f1c44408 f2531340
[ 22.847283] f3073ca0 c16935ca f1c44400 f27d3340 f3073cb4 c1693858 f24ddc44 f1c44400
[ 22.847289] f1c4420c f3073cc8 c1693f76 f1c44400 00000001 00000000 f3073ce8 c1694011
[ 22.847290] Call Trace:
[ 22.847295] [<c13848c9>] ? sysfs_hash_and_remove+0x49/0xa0
[ 22.847300] [<c1ae3805>] ? sub_preempt_count+0x55/0xe0
[ 22.847306] [<c16935ca>] device_remove_groups+0x2a/0x40
[ 22.847309] [<c1693858>] device_remove_attrs+0x38/0x60
[ 22.847313] [<c1693f76>] device_del+0xd6/0x150
[ 22.847316] [<c1694011>] device_unregister+0x21/0x60
[ 22.847320] [<c13869e8>] ? sysfs_remove_link+0x18/0x30
[ 22.847323] [<c1697d04>] ? class_compat_remove_link+0x34/0x50
[ 22.847329] [<c18bf5d9>] extcon_dev_unregister+0xf9/0x130
[ 22.847333] [<c18bd21f>] pwrsrc_extcon_dev_reg_callback+0x7f/0xa0
[ 22.847337] [<c1ae36e3>] notifier_call_chain+0x43/0x60
[ 22.847343] [<c12634e1>] __blocking_notifier_call_chain+0x41/0x80
[ 22.847347] [<c126353f>] blocking_notifier_call_chain+0x1f/0x30
[ 22.847351] [<c18bef39>] extcon_dev_notify_add_device+0x19/0x20
[ 22.847354] [<c18bf074>] extcon_dev_register+0x134/0x580
[ 22.847358] [<c1ae3805>] ? sub_preempt_count+0x55/0xe0
[ 22.847363] [<c154b4da>] ? gpiod_request+0x6a/0x1d0
[ 22.847368] [<c132528a>] ? kmem_cache_alloc_trace+0xaa/0x170
[ 22.847372] [<c18c0179>] ? fsa9285_probe+0x99/0x3f0
[ 22.847375] [<c18c00e0>] ? fsa9285_irq_handler+0xf0/0xf0
[ 22.847379] [<c18c019f>] fsa9285_probe+0xbf/0x3f0
[ 22.847383] [<c18c00e0>] ? fsa9285_irq_handler+0xf0/0xf0
[ 22.847388] [<c1828d9e>] i2c_device_probe+0x7e/0xf0
[ 22.847392] [<c1386e52>] ? sysfs_create_link+0x22/0x40
[ 22.847395] [<c1696c62>] ? driver_sysfs_add+0x72/0xa0
[ 22.847399] [<c1697119>] driver_probe_device+0x79/0x360
[ 22.847403] [<c1697491>] __driver_attach+0x91/0xa0
[ 22.847407] [<c1697400>] ? driver_probe_device+0x360/0x360
[ 22.847410] [<c16955a2>] bus_for_each_dev+0x42/0x80
[ 22.847414] [<c1696bee>] driver_attach+0x1e/0x20
[ 22.847417] [<c1697400>] ? driver_probe_device+0x360/0x360
[ 22.847420] [<c169675f>] bus_add_driver+0xef/0x270
[ 22.847425] [<c1828e10>] ? i2c_device_probe+0xf0/0xf0
[ 22.847428] [<c1828e10>] ? i2c_device_probe+0xf0/0xf0
[ 22.847432] [<c1697a8a>] driver_register+0x6a/0x160
[ 22.847436] [<c1addb3d>] ? mutex_unlock+0xd/0x10
[ 22.847440] [<c1438ab2>] ? __create_file+0x122/0x2a0
[ 22.847446] [<c20557d3>] ? extcon_class_init+0x15/0x15
[ 22.847450] [<c1827cbb>] i2c_register_driver+0x2b/0xd0
[ 22.847454] [<c1438d05>] ? debugfs_create_file+0x35/0x40
[ 22.847458] [<c20557d3>] ? extcon_class_init+0x15/0x15
[ 22.847461] [<c20557e4>] fsa9285_extcon_init+0x11/0x29
[ 22.847465] [<c12001aa>] do_one_initcall+0xba/0x170
[ 22.847471] [<c2012b4a>] kernel_init_freeable+0x119/0x1b8
[ 22.847475] [<c20124d3>] ? do_early_param+0x7a/0x7a
[ 22.847480] [<c1ac4090>] kernel_init+0x10/0xd0
[ 22.847485] [<c1ae6cf7>] ret_from_kernel_thread+0x1b/0x28
[ 22.847488] [<c1ac4080>] ? rest_init+0x80/0x80
Tested-by: Liu, Chuansheng <chuansheng.liu@intel.com>
Reviewed-by: Liu, Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: xiaoming wang <xiaoming.wang@intel.com>
Signed-off-by: Zhang Dongxing <dongxing.zhang@intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
The I2C controller node needs #address-cells and #size-cells properties,
but these are currently missing. Add them. This allows child nodes to be
parsed correctly.
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
In the case of a device tree system there will be no pdata attached to
the device, causing us to deference a NULL pointer. Better to take the
pdata from the Arizona structure as this will always exist and we know
will have been populated since it is populated by the MFD device which
binds in the extcon driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
Follow-up to commit 294d31e8227c ("sony-laptop: don't change keyboard
backlight settings"): avoid messing up the state on resume. Leave it to
what was before suspending as it's anyway likely that we still don't
know what value we should write to the EC registers. This fix is also
required in 3.12
Cc: stable@vger.kernel.org
Tested-by: Karol Babioch <karol@babioch.de>
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit c284ee2cf12b55fa8496b2d098bf0938688f1c1c. Turns out
the locking was incorrect.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Chao Bi <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For exmaple, keycode: KEY_OK(0x160) is changed by "and" operation with
KEY_MAX(0x2ff) to KEY_KPENTER(96).
Signed-off-by: Andrew Liu <andrew.liu200917@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity into for-linus
|
|
git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
The imx fixes for 3.13, part 2:
- Disable S/PDIF "rxtx5" clock option to fix the clocksource breakage
introduced by S/PDIF driver
* tag 'imx-fixes-3.13-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx6qdl: disable spdif "rxtx5" clock option
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Header file <acpi/acpi.h> contains environemnt settings and architecture
specific implementation that should be included before any other ACPICA
headers in order to keep a consistent build environment for ACPICA users.
The following internal ACPICA header files should be included from
<acpi/acpi.h> and should not be included by other kernel files:
<acpi/acpiosxf.h>
<acpi/acpixf.h>
Clean up incorrect inclusions of these files from non-ACPICA source
files.
[rjw: Subject and changelog]
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Without the interrupt you'll get problems if you enable
CONFIG_RTC_DRV_MAX77686. Setup the interrupt properly in the device
tree.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: stable@vger.kernel.org
|
|
Looks like we need to configure the regulators and use the pdata
quirk to make eMMC work with device tree.
It seems that mostly vaux3 is used, and only some earlier revisions
used vmmc2. This has been tested to work on devices where the
system_rev passed by the bootloader has versions 0x0010, 0x2101
and 0x2204.
Cc: devicetree@vger.kernel.org
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Sebastian Reichel <sre@debian.org>
[tony@atomide.com: updated with pinctrl changes and comments from Sebastian]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We do not have REGULATOR_FIXED selected if no boards are selected
and we boot with device tree. This can cause various devices to
fail.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
After dropping the duplicate data in hwmod that now should come from
the .dts files, I noticed few more entries missing. Let's add these
as otherwise devices relying on these won't work.
Looks like the side tone entries are bundled into the mcbsp1 to 3,
so that may needs some special handling in the hwmod code as it's
currently trying to look up mcbsp2_sidetone and mcbsp3_sidetone
entries.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch implements the power_down_finish() method for TC2, to
enable the kernel to confirm when CPUs are safely powered down.
The information required for determining when a CPU is parked
cannot be obtained from any single place, so a few sources of
information must be combined:
* mcpm_cpu_power_down() must be pending for the CPU, so that we
don't get confused by false STANDBYWFI positives arising from
CPUidle. This is detected by waiting for the tc2_pm use count
for the target CPU to reach 0.
* Either the SPC must report that the CPU has asserted
STANDBYWFI, or the TC2 tile's reset control logic must be
holding the CPU in reset.
Just checking for STANDBYWFI is not sufficient, because this
signal is not latched when the the cluster is clamped off and
powered down: the relevant status bits just drop to zero. This
means that STANDBYWFI status cannot be used for reliable
detection of the last CPU in a cluster reaching WFI.
This patch is required in order for kexec to work with MCPM on TC2.
MCPM code was changed in commit 0de0d6467525 ('ARM: 7848/1: mcpm:
Implement cpu_kill() to synchronise on powerdown'), and since then it
will hit a WARN_ON_ONCE() due to power_down_finish not being implemented
on the TC2 platform.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Pasting the verbatim PCI_(VENDOR|DEVICE)_* macros in the __pci_fixup_*
symbol names results in insanely long names such as
__pci_fixup_resumePCI_VENDOR_ID_SERVERWORKSPCI_DEVICE_ID_SERVERWORKS_HT1000SBquirk_disable_broadcom_boot_interrupt
When Link-Time Optimization adds its numeric suffix to such symbol, it
overflows the namebuf[KSYM_NAME_LEN] array in kernel/kallsyms.c. Use the
line number instead to create (nearly) unique symbol names.
Reported-by: Joe Mario <jmario@redhat.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Andi Kleen <ak@linux.intel.com>
|
|
idlestates in sysfs are counted from 0.
This fixes a wrong error message.
Current behavior on a machine with 4 sleep states is:
cpupower idle-set -e 4
Idlestate 4 enabled on CPU 0
-----Wrong---------------------
cpupower idle-set -e 5
Idlestate enabling not supported by kernel
-----Must and now will be -----
cpupower idle-set -e 5
Idlestate 6 not available on CPU 0
-------------------------------
cpupower idle-set -e 6
Idlestate 6 not available on CPU 0
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The cpupower idle-set subcommand was introduce recently.
This patch provides the missing manpage.
If cpupower is properly installed it will show up automatically
(similar to git), when invoking:
cpupower help idle-set
or
cpupower idle-set --help
Some parts have been taken over and adjusted from
git commit 62d6ae880e3e76098
documentation submitted by Carsten Emde.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
"ret" needs to be signed for the error handling to work.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Both sides of the comparison are the same, looks like a cut-and-paste error.
Spotted by Coverity.
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
After commit bcdde7e221a8 (sysfs: make __sysfs_remove_dir() recursive)
I'm seeing traces analogous to the one below in Thunderbolt testing:
WARNING: CPU: 3 PID: 76 at /scratch/rafael/work/linux-pm/fs/sysfs/group.c:214 sysfs_remove_group+0x59/0xe0()
sysfs group ffffffff81c6c500 not found for kobject '0000:08'
Modules linked in: ...
CPU: 3 PID: 76 Comm: kworker/u16:7 Not tainted 3.13.0-rc1+ #76
Hardware name: Acer Aspire S5-391/Venus , BIOS V1.02 05/29/2012
Workqueue: kacpi_hotplug acpi_hotplug_work_fn
0000000000000009 ffff8801644b9ac8 ffffffff816b23bf 0000000000000007
ffff8801644b9b18 ffff8801644b9b08 ffffffff81046607 ffff88016925b800
0000000000000000 ffffffff81c6c500 ffff88016924f928 ffff88016924f800
Call Trace:
[<ffffffff816b23bf>] dump_stack+0x4e/0x71
[<ffffffff81046607>] warn_slowpath_common+0x87/0xb0
[<ffffffff810466d1>] warn_slowpath_fmt+0x41/0x50
[<ffffffff811e42ef>] ? sysfs_get_dirent_ns+0x6f/0x80
[<ffffffff811e5389>] sysfs_remove_group+0x59/0xe0
[<ffffffff8149f00b>] dpm_sysfs_remove+0x3b/0x50
[<ffffffff81495818>] device_del+0x58/0x1c0
[<ffffffff814959c8>] device_unregister+0x48/0x60
[<ffffffff813254fe>] pci_remove_bus+0x6e/0x80
[<ffffffff81325548>] pci_remove_bus_device+0x38/0x110
[<ffffffff8132555d>] pci_remove_bus_device+0x4d/0x110
[<ffffffff81325639>] pci_stop_and_remove_bus_device+0x19/0x20
[<ffffffff813418d0>] disable_slot+0x20/0xe0
[<ffffffff81341a38>] acpiphp_check_bridge+0xa8/0xd0
[<ffffffff813427ad>] hotplug_event+0x17d/0x220
[<ffffffff81342880>] hotplug_event_work+0x30/0x70
[<ffffffff8136d665>] acpi_hotplug_work_fn+0x18/0x24
[<ffffffff81061331>] process_one_work+0x261/0x450
[<ffffffff81061a7e>] worker_thread+0x21e/0x370
[<ffffffff81061860>] ? rescuer_thread+0x300/0x300
[<ffffffff81068342>] kthread+0xd2/0xe0
[<ffffffff81068270>] ? flush_kthread_worker+0x70/0x70
[<ffffffff816c19bc>] ret_from_fork+0x7c/0xb0
[<ffffffff81068270>] ? flush_kthread_worker+0x70/0x70
(Mika Westerberg sees them too in his tests).
Some investigation documented in kernel bug #65281 led me to the
conclusion that the source of the problem is the device_del() in
pci_stop_dev() as it now causes the sysfs directory of the device to be
removed recursively along with all of its subdirectories. That includes
the sysfs directory of the device's subordinate bus (dev->subordinate) and
its "power" group.
Consequently, when pci_remove_bus() is called for dev->subordinate in
pci_remove_bus_device(), it calls device_unregister(&bus->dev), but at this
point the sysfs directory of bus->dev doesn't exist any more and its
"power" group doesn't exist either. Thus, when dpm_sysfs_remove() called
from device_del() tries to remove that group, it triggers the above
warning.
That indicates a logical mistake in the design of
pci_stop_and_remove_bus_device(), which causes bus device objects to be
left behind their parents (bridge device objects) and can be fixed by
moving the device_del() from pci_stop_dev() into pci_destroy_dev(), so
pci_remove_bus() can be called for the device's subordinate bus before the
device itself is unregistered from the hierarchy. Still, the driver, if
any, should be detached from the device in pci_stop_dev(), so use
device_release_driver() directly from there.
References: https://bugzilla.kernel.org/show_bug.cgi?id=65281#c6
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
This reverts commit c2fda509667b0fda4372a237f5a59ea4570b1627.
c2fda509667b removed lockdep annotation from work_on_cpu() to work around
the PCI path that calls work_on_cpu() from within a work_on_cpu() work item
(PF driver .probe() method -> pci_enable_sriov() -> add VFs -> VF driver
.probe method).
961da7fb6b22 ("PCI: Avoid unnecessary CPU switch when calling driver
.probe() method) avoids that recursive work_on_cpu() use in a different
way, so this revert restores the work_on_cpu() lockdep annotation.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
|
|
In order to support increased build test coverage for drivers, implement
dummies for the powergate implementation. This will allow the drivers to
be built without requiring support for Tegra to be selected.
This patch solves the following build errors, which can be triggered in
v3.13-rc1 by selecting DRM_TEGRA without ARCH_TEGRA:
drivers/built-in.o: In function `gr3d_remove':
drivers/gpu/drm/tegra/gr3d.c:321: undefined reference to `tegra_powergate_power_off'
drivers/gpu/drm/tegra/gr3d.c:325: undefined reference to `tegra_powergate_power_off'
drivers/built-in.o: In function `gr3d_probe':
drivers/gpu/drm/tegra/gr3d.c:266: undefined reference to `tegra_powergate_sequence_power_up'
drivers/gpu/drm/tegra/gr3d.c:273: undefined reference to `tegra_powergate_sequence_power_up'
Signed-off-by: Thierry Reding <treding@nvidia.com>
[swarren, updated commit description]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Few more fixes for issues found booting older omaps using device tree.
Also few randconfig build fixes and removal of some dead code for omap4
as it no longer has legacy platform data based booting support.
* tag 'omap-for-v3.13/more-fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
|
|
Some omap3 code is throwing a warning:
arch/arm/mach-omap2/pm34xx.c: In function 'omap3_save_secure_ram_context':
arch/arm/mach-omap2/pm34xx.c:123:32: warning: cast to pointer from
integer of different size [-Wint-to-pointer-cast]
In reality this code will never actually execute with LPAE=y, since
Cortex-A8 doesn't support it. So downcasting the __pa() is safe in
this case.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
If we are already on a CPU local to the device, call the driver .probe()
method directly without using work_on_cpu().
This is a workaround for a lockdep warning in the following scenario:
pci_call_probe
work_on_cpu(cpu, local_pci_probe, ...)
driver .probe
pci_enable_sriov
...
pci_bus_add_device
...
pci_call_probe
work_on_cpu(cpu, local_pci_probe, ...)
It would be better to fix PCI so we don't call VF driver .probe() methods
from inside a PF driver .probe() method, but that's a bigger project.
[bhelgaas: open bugzilla, rework comments & changelog]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=65071
Link: http://lkml.kernel.org/r/CAE9FiQXYQEAZ=0sG6+2OdffBqfLS9MpoN1xviRR9aDbxPxcKxQ@mail.gmail.com
Link: http://lkml.kernel.org/r/20130624195942.40795.27292.stgit@ahduyck-cp1.jf.intel.com
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
|
|
* acpi-hotplug:
ACPI / hotplug: Fix conflicted PCI bridge notify handlers
* acpi-sysfs:
ACPI / sysfs: Fix incorrect ACPI tables walk in acpi_tables_sysfs_init()
ACPI / sysfs: Set file size for each exposed ACPI table
* acpi-sleep:
ACPI / sleep: clean up compiler warning about uninitialized field
|
|
When the system enters suspend, it disables all interrupts in
suspend_device_irqs(), including the interrupts marked EARLY_RESUME.
On the resume side things are different. The EARLY_RESUME interrupts
are reenabled in sys_core_ops->resume and the non EARLY_RESUME
interrupts are reenabled in the normal system resume path.
When suspend_noirq() failed or suspend is aborted for any other
reason, we might omit the resume side call to sys_core_ops->resume()
and therefor the interrupts marked EARLY_RESUME are not reenabled and
stay disabled forever.
To solve this, enable all irqs unconditionally in irq_resume()
regardless whether interrupts marked EARLY_RESUMEhave been already
enabled or not.
This might try to reenable already enabled interrupts in the non
failure case, but the only affected platform is XEN and it has been
confirmed that it does not cause any side effects.
[ tglx: Massaged changelog. ]
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by-and-tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Cc: <ian.campbell@citrix.com>
Cc: <rjw@rjwysocki.net>
Cc: <len.brown@intel.com>
Cc: <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1385388587-16442-1-git-send-email-ldewangan@nvidia.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
usb phy was power'ed on but was never power'ed off in the error path.
Fix it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
usb_phy_set_suspend(phy, 0) is called before usb_phy_init. Fix it.
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
If the next seqno returned by the firmware is 0, we return an error
(-16) in the iwl_mvm_get_last_nonqos_seq() function. This is because
we return an integer and don't use any casting when calculating the
last seqno from the one we received. Fix this by using a cast to u16
when doing the calculation, so we return 0xfff0, as we should.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
In an open BSS, after suspend/resume, we don't set the last seqno
because the iwl_mvm_setup_connection_keep() returns too early. This
happens because the check to see if we have any keys was returning
immediately, without setting seqno and seqno_valid. Fix this.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
If we call ieee80211_hw_restart, it means that the
firmware is in bad condition and will be reset soon.
Since the firmware will be reset, there is no good
reason to keep sending host commands.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
A new firmware is coming out soon with new APIs.
To make sure that this new firmware won't be loaded on old
driver that don't support it, it's API version has been
updated to 8. In order to be able to load it, bump the API
version to 8.
API version 7 is still supported and will be for another
year or so.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Time event notification can have a failure status even if
the time event was scheduled:
* in START notification, this can happen if the time event
was scheduled later than the requested apply time.
* in STOP notification, this can happen if the time event
is truncated.
Even if both happened, the offchannel packets sent during
the remain on channel are very likely to have been sent.
Hence, don't WARN when this happens, but rather print a
discrete line in the kernel log.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch is very similar to a previous fix: 22cba0c0852f
When we disassociate, mac80211 removes the station and
then, it sets the bss it unsets the assoc bool in bss_info.
Since the firwmware wants it the opposite (first set the
MAC context as unassoc, and only then, remove the STA of
the API), we have a small period of time in which the STA
in firmware doesn't have a valid ieee80211_sta pointer.
During that time, iwl_mvm_vif->ap_sta_id, is still set
to the STA in firmware that represent the AP.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
This feature isn't supported by the firmware (yet).
Note that settingt he values to BT_CFG_CMD is harmless if
the validity bit is clear - so keep the configuration
values in BT_CFG_CMD, but clear the validity bit until thes
feature is enabled in the firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Add new HW IDs and configurations for 7265 series.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
We changed the timeout for the interrupt coealescing for
calibration, but that wasn't effective since we changed
that value back before loading the firmware. Since
calibrations are notification from firmware and not Rx
packets, this doesn't change anyway - the firmware will
fire an interrupt straight away regardless of the interrupt
coalescing value.
Also, a HW issue has been discovered in 7000 devices series.
The work around is to disable the new interrupt coalescing
timeout feature - do this by setting bit 31 in
CSR_INT_COALESCING.
This has been fixed in 7265 which means that we can't rely
on the device family and must have a hint in the iwl_cfg
structure.
Cc: stable@vger.kernel.org [3.10+]
Fixes: 99cd47142399 ("iwlwifi: add 7000 series device configuration")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The station ID must be valid, if it's out of range then
the array access may crash. Validate the station ID to
the array length, and also validate the drain value even
if that doesn't matter all that much.
Cc: stable@vger.kernel.org
Fixes: 8ca151b568b6 ("iwlwifi: add the MVM driver")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
zsmalloc encodes a handle using the pfn and an object
index. On hardware platforms with physical memory starting
at 0x0 the pfn can be 0. This causes the encoded handle to be
0 and is incorrectly interpreted as an allocation failure.
This issue affects all current and future SoCs with physical
memory starting at 0x0. All MSM8974 SoCs which includes
Google Nexus 5 devices are affected.
To prevent this false error we ensure that the encoded handle
will not be 0 when allocation succeeds.
Signed-off-by: Olav Haugan <ohaugan@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It was introduced due to a patch hunk when porting
commit 20802057 (staging/lustre/ptlrpc: race in pinger).
Cc: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Peng Tao <bergwolf@gmail.com>
Cc: stable <stable@vger.kernel.org> # 3.12
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Two code lines were accidentally deleted. Restore them.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
