| Age | Commit message (Collapse) | Author |
|---|
|
Serge Semin says:
====================
net: phy: realtek: Fix RGMII TX/RX-delays initial config of rtl8211(e|f)
It has been discovered that RX/TX delays of rtl8211e ethernet PHY
can be configured via a MDIO register hidden in the extension pages
layout. Particularly the extension page 0xa4 provides a register 0x1c,
which bits 1 and 2 control the described delays. They are used to
implement the "rgmii-{id,rxid,txid}" phy-mode support in patch 1.
The second patch makes sure the rtl8211f TX-delay is configured only
if RGMII interface mode is specified including the rgmii-rxid one.
In other cases (most importantly for NA mode) the delays are supposed
to be preconfigured by some other software or hardware and should be
left as is without any modification. The similar thing is also done
for rtl8211e in the patch 1 of this series.
Changelog v3
- Add this cover-letter.
- Add Andrew' Reviewed-by tag to patch 1.
- Accept RGMII_RXID interface mode for rtl8211f and clear the TX_DELAY
bit in this case.
- Initialize ret variable with 0 to prevent the "may be used uninitialized"
warning in patch 1.
Changelog v4
- Rebase onto net-next
====================
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's prone to problems if delay is cleared out for other than RGMII
modes. So lets set/clear the TX-delay in the config register only
if actually RGMII-like interface mode is requested. This only
concerns rtl8211f chips.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two chip pins named TXDLY and RXDLY which actually adds the 2ns
delays to TXC and RXC for TXD/RXD latching. Alas this is the only
documented info regarding the RGMII timing control configurations the PHY
provides. It turns out the same settings can be setup via MDIO registers
hidden in the extension pages layout. Particularly the extension page 0xa4
provides a register 0x1c, which bits 1 and 2 control the described delays.
They are used to implement the "rgmii-{id,rxid,txid}" phy-mode.
The hidden RGMII configs register utilization was found in the rtl8211e
U-boot driver:
https://elixir.bootlin.com/u-boot/v2019.01/source/drivers/net/phy/realtek.c#L99
There is also a freebsd-folks discussion regarding this register:
https://reviews.freebsd.org/D13591
It confirms that the register bits field must control the so called
configuration pins described in the table 12-13 of the official PHY
datasheet:
8:6 = PHY Address
5:4 = Auto-Negotiation
3 = Interface Mode Select
2 = RX Delay
1 = TX Delay
0 = SELRGV
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This provides a new input driver for supporting the power button on
Basin Cove PMIC, found on Intel Merrifield-based devices.
The driver follows the design used in intel_chtdc_ti_pwrbtn.c module.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Some of latest ASUS laptops support new fn-lock mode switching.
This commit detect whether if the fn-lock option is enabled in
BIOS setting, and toggle the fn-lock mode via a new WMI DEVID
0x00100023 when the corresponding notify code captured.
The ASUS fn-lock mode switch is activated by pressing Fn+Esc.
When on, keys F1 to F12 behave as applicable, with meanings
defined by the application being used at the time. When off,
F1 to F12 directly triggers hardware features, well known audio
volume up/down, brightness up/down...etc, which were triggered
by holding down Fn key and F-keys.
Because there's no way to retrieve the fn-lock mode via existing
WMI methods per ASUS spec, driver need to initialize and keep the
fn-lock mode by itself.
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Reviewed-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
When the ideapad-laptop driver was first written it was written for laptops
which had a hardware rfkill switch. So when the first ideapad laptops
showed up without a hw rfkill switch and it turned out that in this case
the ideapad firmware interface would always report the wifi being hardware-
blocked, a DMI id list of models which lack a hw rfkill switch was started
(by yours truly). Things were done this way to avoid regressing existing
models with a hw rfkill switch. In hindsight this was a mistake.
Lenovo releases a lot of ideapad models every year and even the latest
models still use the "VPC2004" ACPI interface the ideapad-laptop driver
binds to. Having a hw rfkill switch is quite rare on modern hardware, so
all these new models need to be added to the no_hw_rfkill_list, leading
to a never ending game of whack a mole.
Worse the failure mode when not present on the list, is very bad. In this
case the ideapad-laptop driver will report the wifi as being hw-blocked,
at which points NetworkManager does not even try to use it and the user
ends up with non working wifi.
This leads to various Linux fora on the internet being filled with
wifi not working on ideapad laptops stories, which does not make Linux
look good.
The failure mode when we flip the default to assuming that a hw rfkill
switch is not present OTOH is quite benign. When we properly report the
wifi as being hw-blocked on ideapads which do have the hw-switch; and it
is in the wifi-off position, then at least when using NetworkManager +
GNOME3 the user will get a "wifi disabled in hardware" message when trying
to connect to the wifi from the UI. If OTOH we assume there is no hardware
rfkill switch, then the user will get an empty list for the list of
available networks. Although the empty list vs the "wifi disabled in
hardware" message is a regression, it is a very minor regression and it
can easily be fixed on a model by model basis by filling the new
hw_rfkill_list this commit introduces.
Therefor this commit removes the ever growing no_hw_rfkill_list, flipping
the default to assuming there is no hw rfkill switch and adding a new
hw_rfkill_list. Thereby fixing the wifi not working on all the current
ideapad and yoga models which are not on the list yet and also fixing it
for all future ideapad and yoga models using the "VPC2004" ACPI interface.
Note once this patch has been accepted upstream. I plan to write a blog
post asking for users of ideapads and yoga's with a hw rfkill switch to
step forward, so that we can populate the new hw_rfkill_list with the few
older yoga and ideapad models which actually have a hw rfkill switch.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1703338
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Add touchscreen platform data for the 'jumper ezpad 6 pro b' touchscreen.
Signed-off-by: Benjamin Renz <appswert@gmail.com>
[hdegoede@redhat.com: Cleanup commit msg, fix some checkpatch warnings]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Make error returns more consistent... no behaviour change intended.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/platform/x86/thinkpad_acpi.c: In function ‘thermal_get_sensor’:
drivers/platform/x86/thinkpad_acpi.c:6316:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (idx >= 8 && idx <= 15) {
^
drivers/platform/x86/thinkpad_acpi.c:6322:2: note: here
case TPACPI_THERMAL_TPEC_8:
^~~~
drivers/platform/x86/thinkpad_acpi.c: In function ‘hotkey_notify’:
drivers/platform/x86/thinkpad_acpi.c:4208:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (tp_features.hotkey_wlsw &&
^
drivers/platform/x86/thinkpad_acpi.c:4216:3: note: here
default:
^~~~~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comments are modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
It seems that the default case should return AE_CTRL_TERMINATE, instead
of falling through to case ACPI_RESOURCE_TYPE_END_TAG and returning AE_OK;
otherwise the line of code at the end of the function is unreachable and
makes no sense:
return AE_CTRL_TERMINATE;
This fix is based on the following thread of discussion:
https://lore.kernel.org/patchwork/patch/959782/
Fixes: 33a04454527e ("sony-laptop: Add SNY6001 device handling (sonypi reimplementation)")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
The "out_data" variable is uninitialized at the point. Originally, this
used to print "status" instead and that seems like the correct thing to
print.
Fixes: bc2ef884320b ("alienware-wmi: For WMAX HDMI method, introduce a way to query HDMI cable status")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Dan Carpenter says:
The patch 640f763f98c2: "net: dsa: sja1105: Add support for Spanning
Tree Protocol" from May 5, 2019, leads to the following static
checker warning:
drivers/net/dsa/sja1105/sja1105_main.c:1073 sja1105_stp_state_get()
warn: signedness bug returning '(-22)'
The caller doesn't check for negative errors anyway.
Fixes: 640f763f98c2: ("net: dsa: sja1105: Add support for Spanning Tree Protocol")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2
Pull GFS2 updates from Andreas Gruenbacher:
"We've got the following patches ready for this merge window:
- "gfs2: Fix loop in gfs2_rbm_find (v2)"
A rework of a fix we ended up reverting in 5.0 because of an
iozone performance regression.
- "gfs2: read journal in large chunks"
"gfs2: fix race between gfs2_freeze_func and unmount"
An improved version of a commit we also ended up reverting in 5.0
because of a regression in xfstest generic/311. It turns out that
the journal changes were mostly innocent and that unfreeze didn't
wait for the freeze to complete, which caused the filesystem to be
unmounted before it was actually idle.
- "gfs2: Fix occasional glock use-after-free"
"gfs2: Fix iomap write page reclaim deadlock"
"gfs2: Fix lru_count going negative"
Fixes for various problems reported and partially fixed by Citrix
engineers. Thank you very much.
- "gfs2: clean_journal improperly set sd_log_flush_head"
Another fix from Bob.
- .. and a few other minor cleanups"
* tag 'gfs2-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: read journal in large chunks
gfs2: Fix iomap write page reclaim deadlock
gfs2: fix race between gfs2_freeze_func and unmount
gfs2: Rename gfs2_trans_{add_unrevoke => remove_revoke}
gfs2: Rename sd_log_le_{revoke,ordered}
gfs2: Remove unnecessary extern declarations
gfs2: Remove misleading comments in gfs2_evict_inode
gfs2: Replace gl_revokes with a GLF flag
gfs2: Fix occasional glock use-after-free
gfs2: clean_journal improperly set sd_log_flush_head
gfs2: Fix lru_count going negative
gfs2: Fix loop in gfs2_rbm_find (v2)
|
|
Use __maybe_unused for power management related functions
instead of #if CONFIG_PM_SLEEP to simply the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
This variable is no longer used and the compiler rightly complains that
it should be removed.
../drivers/rtc/rtc-imxdi.c: In function ‘dryice_rtc_set_alarm’:
../drivers/rtc/rtc-imxdi.c:633:16: warning: unused variable ‘now’ [-Wunused-variable]
unsigned long now;
^~~
Rework to remove the unused variable.
Fixes: 629d488a3eb6 ("rtc: imxdi: remove unnecessary check")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
There are no users of set_mms and set_mmss64 as they have all been
converted to set_time and are handling the tm to time conversion on their
own.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Use SPDX-License-Identifier instead of a verbose license text.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Use .set_time instead of the deprecated .set_mmss.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Call the 64bit versions of rtc_tm time conversion now that the range is
enforced by the core.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
While PCAP_RTC_DAY_MASK is set to 0x3ffff, it is very unlikely to be
correct as this ends in june 1992, before the product even existed. It is
more likely to be a 14-bit day counter. The next product in the family (the
mc13xxx) has a 15-bit day counter.
The same issue is seen with PCAP_RTC_TOD_MASK which only has 65535 seconds
and falls short of the necessary 86400 seconds.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Use SPDX-License-Identifier instead of a verbose license text.
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Use .set_time instead of the deprecated .set_mmss.
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
While the range of REFERENCE + TIME is actually 33 bits, the counter
itself (TIME) is a 32-bits seconds counter.
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The IRQ is requested before the struct rtc is allocated and registered, but
this struct is used in the IRQ handler. This may lead to a NULL pointer
dereference.
Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc
struct before requesting the IRQ.
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The while-loop exit condition check is not correct; the
loop should continue if the returns from the function calls are
negative or the CRC status returns are invalid. Currently it
is ignoring the returns from the function calls. Fix this by
removing the status return checks and only break from the loop
at the very end when we know that all the success condtions have
been met.
Kudos to Dan Carpenter for describing the correct fix and
Vladimir Oltean for noting the change to the check on the number
of retries.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 8aa9ebccae87 ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull cifs fixes from Steve French:
"CIFS/SMB3 changes:
- three fixes for stable
- add fiemap support
- improve zero-range support
- various RDMA (smb direct fixes)
I have an additional set of fixes (for improved handling of sparse
files, mode bits, POSIX extensions) that are still being tested that
are not included in this pull request but I expect to send in the next
week"
* tag '5.2-smb3' of git://git.samba.org/sfrench/cifs-2.6: (29 commits)
cifs: update module internal version number
SMB3: Clean up query symlink when reparse point
cifs: fix strcat buffer overflow and reduce raciness in smb21_set_oplock_level()
Negotiate and save preferred compression algorithms
cifs: rename and clarify CIFS_ASYNC_OP and CIFS_NO_RESP
cifs: fix credits leak for SMB1 oplock breaks
smb3: Add protocol structs for change notify support
cifs: fix smb3_zero_range for Azure
cifs: zero-range does not require the file is sparse
Add new flag on SMB3.1.1 read
cifs: add fiemap support
SMB3: Add defines for new negotiate contexts
cifs: fix bi-directional fsctl passthrough calls
cifs: smbd: take an array of reqeusts when sending upper layer data
SMB3: Add handling for different FSCTL access flags
cifs: Add support for FSCTL passthrough that write data to the server
cifs: remove superfluous inode_lock in cifs_{strict_}fsync
cifs: Call MID callback before destroying transport
cifs: smbd: Retry on memory registration failure
cifs: smbd: Indicate to retry on transport sending failure
...
|
|
Depending on platform firmware, a zap shader may not be required to take
the GPU out of secure mode on boot, in which case we can just write
RBBM_SECVID_TRUST_CNTL directly. Which we *mostly* handled, but missed
clearing 'ret' resulting that hw_init() returned an error on these
devices.
Fixes: abccb9fe3267 ("drm/msm/a6xx: Add zap shader load")
Acked-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190508130726.27557-1-robdclark@gmail.com
|
|
Pull documentation updates from Jonathan Corbet:
"A reasonably busy cycle for docs, including:
- Lots of work on the Chinese and Italian translations
- Some license-rules clarifications from Christoph
- Various build-script fixes
- A new document on memory models
- RST conversion of the live-patching docs
- The usual collection of typo fixes and corrections"
* tag 'docs-5.2' of git://git.lwn.net/linux: (140 commits)
docs/livepatch: Unify style of livepatch documentation in the ReST format
docs: livepatch: convert docs to ReST and rename to *.rst
scripts/documentation-file-ref-check: detect broken :doc:`foo`
scripts/documentation-file-ref-check: don't parse Next/ dir
LICENSES: Rename other to deprecated
LICENSES: Clearly mark dual license only licenses
docs: Don't reference the ZLib license in license-rules.rst
docs/vm: Minor editorial changes in the THP and hugetlbfs
docs/vm: add documentation of memory models
doc:it_IT: translation alignment
doc: fix typo in PGP guide
dontdiff: update with Kconfig build artifacts
docs/zh_CN: fix typos in 1.Intro.rst file
docs/zh_CN: redirect CoC docs to Chinese version
doc: mm: migration doesn't use FOLL_SPLIT anymore
docs: doc-guide: remove the extension from .rst files
doc: kselftest: Fix KBUILD_OUTPUT usage instructions
docs: trace: fix some Sphinx warnings
docs: speculation.txt: mark example blocks as such
docs: ntb.txt: add blank lines to clean up some Sphinx warnings
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- allow users to invoke 'make' out of the source tree
- refactor scripts/mkmakefile
- deprecate KBUILD_SRC, which was used to track the source tree
location for O= build.
- fix recordmcount.pl in case objdump output is localized
- turn unresolved symbols in external modules to errors from warnings
by default; pass KBUILD_MODPOST_WARN=1 to get them back to warnings
- generate modules.builtin.modinfo to collect .modinfo data from
built-in modules
- misc Makefile cleanups
* tag 'kbuild-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (21 commits)
.gitignore: add more all*.config patterns
moduleparam: Save information about built-in modules in separate file
Remove MODULE_ALIAS() calls that take undefined macro
.gitignore: add leading and trailing slashes to generated directories
scripts/tags.sh: fix direct execution of scripts/tags.sh
scripts: override locale from environment when running recordmcount.pl
samples: kobject: allow CONFIG_SAMPLE_KOBJECT to become y
samples: seccomp: turn CONFIG_SAMPLE_SECCOMP into a bool option
kbuild: move Documentation to vmlinux-alldirs
kbuild: move samples/ to KBUILD_VMLINUX_OBJS
modpost: make KBUILD_MODPOST_WARN also configurable for external modules
kbuild: check arch/$(SRCARCH)/include/generated before out-of-tree build
kbuild: remove unneeded dependency for include/config/kernel.release
memory: squash drivers/memory/Makefile.asm-offsets
kbuild: use $(srctree) instead of KBUILD_SRC to check out-of-tree build
kbuild: mkmakefile: generate a simple wrapper of top Makefile
kbuild: mkmakefile: do not check the generated Makefile marker
kbuild: allow Kbuild to start from any directory
kbuild: pass $(MAKECMDGOALS) to sub-make as is
kbuild: fix warning "overriding recipe for target 'Makefile'"
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wtarreau/nolibc
Pull RISC-V nolibc header update from Willy Tarreau:
"This single commit adds support for the RISCV architecture to the
nolibc header file. Currently the file is only used by rcutorture but
Pranith Kumar who contributed it would like to have this work merged.
I only did some trivial tests to verify that it does not break x86,
which I consider sufficient since all the code is cleanly enclosed
inside a single #if/endif block"
* tag 'nolibc-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wtarreau/nolibc:
tool headers nolibc: add RISCV support
|
|
Pull arch/csky updates from Guo Ren:
- Fixup vdsp&fpu issues in kernel
- Add dynamic function tracer
- Use in_syscall & forget_syscall instead of r11_sig
- Reconstruct signal processing
- Support dynamic start physical address
- Fixup wrong update_mmu_cache implementation
- Support vmlinux bootup with MMU off
- Use va_pa_offset instead of phys_offset
- Fixup syscall_trace return processing flow
- Add perf callchain support
- Add perf_arch_fetch_caller_regs support
- Add page fault perf event support
- Add support for perf registers sampling
* tag 'csky-for-linus-5.2-rc1' of git://github.com/c-sky/csky-linux:
csky/syscall_trace: Fixup return processing flow
csky: Fixup compile warning
csky: Add support for perf registers sampling
csky: add page fault perf event support
csky: Use va_pa_offset instead of phys_offset
csky: Support vmlinux bootup with MMU off
csky: Add perf_arch_fetch_caller_regs support
csky: Fixup wrong update_mmu_cache implementation
csky: Support dynamic start physical address
csky: Reconstruct signal processing
csky: Use in_syscall & forget_syscall instead of r11_sig
csky: Add non-uapi asm/ptrace.h namespace
csky: mm/fault.c: Remove duplicate header
csky: remove redundant generic-y
csky: Update syscall_trace_enter/exit implementation
csky: Add perf callchain support
csky/ftrace: Add dynamic function tracer (include graph tracer)
csky: Fixup vdsp&fpu issues in kernel
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- remove the deprecated Zoran driver from staging
- new I2C driver: ST MIPID02 CSI-2 camera bridge
- new platform driver: Amlogic Meson AO CEC G12A Controller
- add support for USB audio via the media controller
- au0828 driver is now supported via the media controller on both on
media and on usbaudio
- new kernel test for the media device allocator
- add support for stateless decoder at vicodec driver
- lots of other driver improvements fixes and cleanups
* tag 'media/v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (218 commits)
media: dt-bindings: aspeed-video: Add missing memory-region property
media: platform: Aspeed: Make reserved memory optional
media: platform: Aspeed: Remove use of reset line
media: stm32-dcmi: return appropriate error codes during probe
media: vsp1: Add support for missing 16-bit RGB555 formats
media: vsp1: Add support for missing 16-bit RGB444 formats
media: vsp1: Add support for missing 32-bit RGB formats
media: v4l: Add definitions for missing 16-bit RGB555 formats
media: v4l: Add definitions for missing 16-bit RGB4444 formats
media: v4l: Add definitions for missing 32-bit RGB formats
media: zoran: remove deprecated driver
media: MAINTAINERS: Update AO CEC with ao-cec-g12a driver
media: platform: meson: Add Amlogic Meson G12A AO CEC Controller driver
media: dt-bindings: media: meson-ao-cec: Add G12A AO-CEC-B Compatible
media: cros-ec-cec: decrement HDMI device refcount
media: seco-cec: decrement HDMI device refcount
media: tegra_cec: use new cec_notifier_parse_hdmi_phandle helper
media: stih_cec: use new cec_notifier_parse_hdmi_phandle helper
media: s5p_cec: use new cec_notifier_parse_hdmi_phandle helper
media: meson: ao-cec: use new cec_notifier_parse_hdmi_phandle helper
...
|
|
Pull IPMI updates from Corey Minyard:
"Some minor cleanups for the IPMI driver"
* tag 'for-linus-5.2' of git://github.com/cminyard/linux-ipmi:
ipmi: Remove warning if no slave address is present
ipmi:ssif: Only unregister the platform driver if it was registered
ipmi:ssif: compare block number correctly for multi-part return messages
ipmi: Add the i2c-addr property for SSIF interfaces
char/ipmi: fix spelling mistake "receieved_messages" -> "received_messages"
ipmi: avoid atomic_inc in exit function
ipmi: Remove file from ipmi_file_private
ipmi_si: remove an unused variable in try_smi_init()
ipmi: Make ipmi_interfaces_srcu variable static
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"It is pretty calm and chill in pin control for the moment. Just
incremental development.
There is an odd patch to the Super-H architecture, it's coming from
the maintainers so should be fine.
Summary:
New drivers:
- Bitmain BM1880 pin controller
- Mediatek MT8516
- Cirrus Logich Lochnagar PMIC pins
Updates:
- Incremental development on Renesas SH-PFC
- Incremental development on Intel pin controller and some particular
updates for Cedarfork.
- Pin configuration support in Allwinner SunXi drivers
- Suspend/resume support in the NXP/Freescale i.MX8MQ driver
- Support for more packaging of the ST Micro STM32"
* tag 'pinctrl-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: mcp23s08: Do not complain about unsupported params
pinctrl: Rework Kconfig dependency for BM1880 pinctrl driver
MAINTAINERS: Add entry for BM1880 pinctrl
pinctrl: Add pinctrl support for BM1880 SoC
dt-bindings: pinctrl: Add BM1880 pinctrl binding
pinctrl: stm32: check irq controller availability at probe
pinctrl: mediatek: Add MT8516 Pinctrl driver
pinctrl: zte: fix leaked of_node references
pinctrl: intel: Increase readability of intel_gpio_update_pad_mode()
pinctrl: intel: Retain HOSTSW_OWN for requested gpio pin
pinctrl: pistachio: fix leaked of_node references
pinctrl: sunxi: Support I/O bias voltage setting on H6
pinctrl: sunxi: Prepare for alternative bias voltage setting methods
pinctrl: st: fix leaked of_node references
pinctrl: samsung: fix leaked of_node references
pinctrl: stm32: align stm32mp157 pin names
pinctrl: stm32: add package information for stm32mp157c
pinctrl: stm32: introduce package support
dt-bindings: pinctrl: stm32: add new entry for package information
pinctrl: imx8mq: Add suspend/resume ops
...
|
|
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, qedf, smartpqi,
hpsa, lpfc, ufs, mpt3sas, ibmvfc and hisi_sas. Plus number of minor
changes, spelling fixes and other trivia"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (298 commits)
scsi: qla2xxx: Avoid that lockdep complains about unsafe locking in tcm_qla2xxx_close_session()
scsi: qla2xxx: Avoid that qlt_send_resp_ctio() corrupts memory
scsi: qla2xxx: Fix hardirq-unsafe locking
scsi: qla2xxx: Complain loudly about reference count underflow
scsi: qla2xxx: Use __le64 instead of uint32_t[2] for sending DMA addresses to firmware
scsi: qla2xxx: Introduce the dsd32 and dsd64 data structures
scsi: qla2xxx: Check the size of firmware data structures at compile time
scsi: qla2xxx: Pass little-endian values to the firmware
scsi: qla2xxx: Fix race conditions in the code for aborting SCSI commands
scsi: qla2xxx: Use an on-stack completion in qla24xx_control_vp()
scsi: qla2xxx: Make qla24xx_async_abort_cmd() static
scsi: qla2xxx: Remove unnecessary locking from the target code
scsi: qla2xxx: Remove qla_tgt_cmd.released
scsi: qla2xxx: Complain if a command is released that is owned by the firmware
scsi: qla2xxx: target: Fix offline port handling and host reset handling
scsi: qla2xxx: Fix abort handling in tcm_qla2xxx_write_pending()
scsi: qla2xxx: Fix error handling in qlt_alloc_qfull_cmd()
scsi: qla2xxx: Simplify qlt_send_term_imm_notif()
scsi: qla2xxx: Fix use-after-free issues in qla2xxx_qpair_sp_free_dma()
scsi: qla2xxx: Fix a qla24xx_enable_msix() error path
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the "big" set of tty/serial driver patches for 5.2-rc1.
It's really pretty small, not much happening in this portion of the
kernel at the moment. When the "highlight" is the movement of the
documentation from .txt to .rst files, it's a good merge window.
There's a number of small fixes and updates over the various serial
drivers, and a new "tty null" driver for those embedded systems that
like to make things even smaller and not break things.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (45 commits)
tty: serial: add driver for the SiFive UART
dt-bindings: serial: add documentation for the SiFive UART driver
serial: uartps: Add support for cts-override
dt-bindings: xilinx-uartps: Add support for cts-override
serial: milbeaut_usio: Fix error handling in probe and remove
tty: rocket: deprecate the rp_ioctl
tty: rocket: Remove RCPK_GET_STRUCT ioctl
tty: update obsolete termios comment
tty: serial_core: fix error code returned by uart_register_driver()
serial: 8250-mtk: modify baudrate setting
serial: 8250-mtk: add follow control
docs: serial: convert docs to ReST and rename to *.rst
serial: 8250_exar: Adjust IOT2000 matching
TTY: serial_core, add ->install
serial: Fix using plain integer instead of Null pointer
tty:serial_core: Spelling mistake
tty: Add NULL TTY driver
tty: vt: keyboard: Allow Unicode compose base char
Revert "tty: fix NULL pointer issue when tty_port ops is not set"
serial: Add Milbeaut serial control
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver patches for 5.2-rc1
There is the usual set of:
- USB gadget updates
- PHY driver updates and additions
- USB serial driver updates and fixes
- typec updates and new chips supported
- mtu3 driver updates
- xhci driver updates
- other tiny driver updates
Nothing really interesting, just constant forward progress.
All of these have been in linux-next for a while with no reported
issues. The usb-gadget and usb-serial trees were merged a bit "late",
but both of them had been in linux-next before they got merged here
last Friday"
* tag 'usb-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (206 commits)
USB: serial: f81232: implement break control
USB: serial: f81232: add high baud rate support
USB: serial: f81232: clear overrun flag
USB: serial: f81232: fix interrupt worker not stop
usb: dwc3: Rename DWC3_DCTL_LPM_ERRATA
usb: dwc3: Fix default lpm_nyet_threshold value
usb: dwc3: debug: Print GET_STATUS(device) tracepoint
usb: dwc3: Do core validation early on probe
usb: dwc3: gadget: Set lpm_capable
usb: gadget: atmel: tie wake lock to running clock
usb: gadget: atmel: support USB suspend
usb: gadget: atmel_usba_udc: simplify setting of interrupt-enabled mask
dwc2: gadget: Fix completed transfer size calculation in DDMA
usb: dwc2: Set lpm mode parameters depend on HW configuration
usb: dwc2: Fix channel disable flow
usb: dwc2: Set actual frame number for completed ISOC transfer
usb: gadget: do not use __constant_cpu_to_le16
usb: dwc2: gadget: Increase descriptors count for ISOC's
usb: introduce usb_ep_type_string() function
usb: dwc3: move synchronize_irq() out of the spinlock protected block
...
|
|
drivers/net/dsa/sja1105/sja1105_spi.c:486:21: warning: symbol 'sja1105et_regs' was not declared. Should it be static?
drivers/net/dsa/sja1105/sja1105_spi.c:511:21: warning: symbol 'sja1105pqrs_regs' was not declared. Should it be static?
Fixes: 8aa9ebccae87 ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai26@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
calling connect(AF_UNSPEC) on an already connected TCP socket is an
established way to disconnect() such socket. After commit 68741a8adab9
("selinux: Fix ltp test connect-syscall failure") it no longer works
and, in the above scenario connect() fails with EAFNOSUPPORT.
Fix the above falling back to the generic/old code when the address family
is not AF_INET{4,6}, but leave the SCTP code path untouched, as it has
specific constraints.
Fixes: 68741a8adab9 ("selinux: Fix ltp test connect-syscall failure")
Reported-by: Tom Deseyn <tdeseyn@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The pointer l2_hdr is being assigned to itself, this is redundant
and can be removed.
Addresses-Coverity: ("Evaluation order violation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are several spelling mistakes in dev_err messages. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 4806e975729f99c7 ("netfilter: replace NF_NAT_NEEDED with
IS_ENABLED(CONFIG_NF_NAT)") removed CONFIG_NF_NAT_NEEDED, but a new user
popped up afterwards.
Fixes: fec9c271b8f1bde1 ("openvswitch: load and reference the NAT helper.")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Florian Westphal <fw@strlen.de>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
inet_iif should be used for the raw socket lookup. inet_iif considers
rt_iif which handles the case of local traffic.
As it stands, ping to a local address with the '-I <dev>' option fails
ever since ping was changed to use SO_BINDTODEVICE instead of
cmsg + IP_PKTINFO.
IPv6 works fine.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
not supplied
With commit 153380ec4b9 ("fib_rules: Added NLM_F_EXCL support to
fib_nl_newrule") we now able to check if a rule already exists. But this
only works with iproute2. For other tools like libnl, NetworkManager,
it still could add duplicate rules with only NLM_F_CREATE flag, like
[localhost ~ ]# ip rule
0: from all lookup local
32766: from all lookup main
32767: from all lookup default
100000: from 192.168.7.5 lookup 5
100000: from 192.168.7.5 lookup 5
As it doesn't make sense to create two duplicate rules, let's just return
0 if the rule exists.
Fixes: 153380ec4b9 ("fib_rules: Added NLM_F_EXCL support to fib_nl_newrule")
Reported-by: Thomas Haller <thaller@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The logic for freeing an imported buffer with a virtual address is
broken. It will free the buffer instead of unmapping the dma buf.
Fix by reversing the if ladder and first check if the buffer is imported.
Fixes: b9068cde51ee ("drm/cma-helper: Add DRM_GEM_CMA_VMAP_DRIVER_OPS")
Cc: stable@vger.kernel.org
Reported-by: "Li, Tingqian" <tingqian.li@intel.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190426124753.53722-1-noralf@tronnes.org
|
|
This adds support for the RISCV architecture (32 and 64 bit) to the
nolibc header file.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
[willy: minimal rewording of the commit message]
Signed-off-by: Willy Tarreau <w@1wt.eu>
|
|
The line6 toneport driver has code for some delayed initialization,
and this hits the kernel Oops because mutex and other sleepable
functions are used in the timer callback. Fix the abuse by a delayed
work instead so that everything works gracefully.
Reported-by: syzbot+a07d0142e74fdd595cfb@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The build of aica sound driver has been broken since the timer API
conversion and some code rewrite. This patch fixes the breakage by
using the common substream field, as well as a bit cleaning up wrt the
timer handling in the code.
Fixes: d522bb6a105f ("ALSA: sh: aica: Convert timers to use timer_setup()")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Remove hp_pin = 0 return. Add the default pin 0x21 as headphone.
Supported low power consumption, it must do depop procedure when
headset jack was plugged or unplugged.
So, alc256_init() and alc256_shutup() must run delay when headset jack
was plugged or unplugged.
If depop procedure not run with delay, it will have a chance to let
power consumption raise high.
[ NOTE: this is a quite quite similar change for ALC295 by commit
d3ba58bb8959 ("ALSA: hda/realtek - Support low power consumption for
ALC295"), but applied to ALC256 codec instead -- tiwai ]
Fixes: 8983eb602af5 ("ALSA: hda/realtek - Move to ACT_INIT state")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.2
A bunch of driver specific fixes that came in since the initial pull
request for v5.2, mainly warning fixes for the newly added Sound Open
Firmware code which people appeared to only start looking at after I'd
sent the pull request.
|
