summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2024-02-23kasan: revert eviction of stack traces in generic modeMarco Elver
This partially reverts commits cc478e0b6bdf, 63b85ac56a64, 08d7c94d9635, a414d4286f34, and 773688a6cb24 to make use of variable-sized stack depot records, since eviction of stack entries from stack depot forces fixed- sized stack records. Care was taken to retain the code cleanups by the above commits. Eviction was added to generic KASAN as a response to alleviating the additional memory usage from fixed-sized stack records, but this still uses more memory than previously. With the re-introduction of variable-sized records for stack depot, we can just switch back to non-evictable stack records again, and return back to the previous performance and memory usage baseline. Before (observed after a KASAN kernel boot): pools: 597 refcounted_allocations: 17547 refcounted_frees: 6477 refcounted_in_use: 11070 freelist_size: 3497 persistent_count: 12163 persistent_bytes: 1717008 After: pools: 319 refcounted_allocations: 0 refcounted_frees: 0 refcounted_in_use: 0 freelist_size: 0 persistent_count: 29397 persistent_bytes: 5183536 As can be seen from the counters, with a generic KASAN config, refcounted allocations and evictions are no longer used. Due to using variable-sized records, I observe a reduction of 278 stack depot pools (saving 4448 KiB) with my test setup. Link: https://lkml.kernel.org/r/20240129100708.39460-2-elver@google.com Fixes: cc478e0b6bdf ("kasan: avoid resetting aux_lock") Fixes: 63b85ac56a64 ("kasan: stop leaking stack trace handles") Fixes: 08d7c94d9635 ("kasan: memset free track in qlink_free") Fixes: a414d4286f34 ("kasan: handle concurrent kasan_record_aux_stack calls") Fixes: 773688a6cb24 ("kasan: use stack_depot_put for Generic mode") Signed-off-by: Marco Elver <elver@google.com> Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com> Tested-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-02-23stackdepot: use variable size records for non-evictable entriesMarco Elver
With the introduction of stack depot evictions, each stack record is now fixed size, so that future reuse after an eviction can safely store differently sized stack traces. In all cases that do not make use of evictions, this wastes lots of space. Fix it by re-introducing variable size stack records (up to the max allowed size) for entries that will never be evicted. We know if an entry will never be evicted if the flag STACK_DEPOT_FLAG_GET is not provided, since a later stack_depot_put() attempt is undefined behavior. With my current kernel config that enables KASAN and also SLUB owner tracking, I observe (after a kernel boot) a whopping reduction of 296 stack depot pools, which translates into 4736 KiB saved. The savings here are from SLUB owner tracking only, because KASAN generic mode still uses refcounting. Before: pools: 893 allocations: 29841 frees: 6524 in_use: 23317 freelist_size: 3454 After: pools: 597 refcounted_allocations: 17547 refcounted_frees: 6477 refcounted_in_use: 11070 freelist_size: 3497 persistent_count: 12163 persistent_bytes: 1717008 [elver@google.com: fix -Wstringop-overflow warning] Link: https://lore.kernel.org/all/20240201135747.18eca98e@canb.auug.org.au/ Link: https://lkml.kernel.org/r/20240201090434.1762340-1-elver@google.com Link: https://lore.kernel.org/all/CABXGCsOzpRPZGg23QqJAzKnqkZPKzvieeg=W7sgjgi3q0pBo0g@mail.gmail.com/ Link: https://lkml.kernel.org/r/20240129100708.39460-1-elver@google.com Link: https://lore.kernel.org/all/CABXGCsOzpRPZGg23QqJAzKnqkZPKzvieeg=W7sgjgi3q0pBo0g@mail.gmail.com/ Fixes: 108be8def46e ("lib/stackdepot: allow users to evict stack traces") Signed-off-by: Marco Elver <elver@google.com> Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com> Tested-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-02-24crypto: arm64/neonbs - fix out-of-bounds access on short inputArd Biesheuvel
The bit-sliced implementation of AES-CTR operates on blocks of 128 bytes, and will fall back to the plain NEON version for tail blocks or inputs that are shorter than 128 bytes to begin with. It will call straight into the plain NEON asm helper, which performs all memory accesses in granules of 16 bytes (the size of a NEON register). For this reason, the associated plain NEON glue code will copy inputs shorter than 16 bytes into a temporary buffer, given that this is a rare occurrence and it is not worth the effort to work around this in the asm code. The fallback from the bit-sliced NEON version fails to take this into account, potentially resulting in out-of-bounds accesses. So clone the same workaround, and use a temp buffer for short in/outputs. Fixes: fc074e130051 ("crypto: arm64/aes-neonbs-ctr - fallback to plain NEON for final chunk") Cc: <stable@vger.kernel.org> Reported-by: syzbot+f1ceaa1a09ab891e1934@syzkaller.appspotmail.com Reviewed-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2024-02-24crypto: lskcipher - Copy IV in lskcipher glue code alwaysHerbert Xu
The lskcipher glue code for skcipher needs to copy the IV every time rather than only on the first and last request. Otherwise those algorithms that use IV to perform chaining may break, e.g., CBC. This is because crypto_skcipher_import/export do not include the IV as part of the saved state. Reported-by: syzbot+b90b904ef6bdfdafec1d@syzkaller.appspotmail.com Fixes: 662ea18d089b ("crypto: skcipher - Make use of internal state") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2024-02-23ps3/gelic: minor Kernel Doc correctionsSimon Horman
* Update the Kernel Doc for gelic_descr_set_tx_cmdstat() and gelic_net_setup_netdev() so that documented name and the actual name of the function match. * Move define of GELIC_ALIGN() so that it is no longer between gelic_alloc_card_net() and it's Kernel Doc. * Document netdev parameter of gelic_alloc_card_net() in a way consistent to the documentation of other netdev parameters in this file. Addresses the following warnings flagged by ./scripts/kernel-doc -none: .../ps3_gelic_net.c:711: warning: expecting prototype for gelic_net_set_txdescr_cmdstat(). Prototype was for gelic_descr_set_tx_cmdstat() instead .../ps3_gelic_net.c:1474: warning: expecting prototype for gelic_ether_setup_netdev(). Prototype was for gelic_net_setup_netdev() instead .../ps3_gelic_net.c:1528: warning: expecting prototype for gelic_alloc_card_net(). Prototype was for GELIC_ALIGN() instead .../ps3_gelic_net.c:1531: warning: Function parameter or struct member 'netdev' not described in 'gelic_alloc_card_net' Signed-off-by: Simon Horman <horms@kernel.org> Acked-by: Geoff Levand <geoff@infradead.org> Link: https://lore.kernel.org/r/20240221-ps3-gelic-kdoc-v1-1-7629216d1340@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-02-23net: mpls: error out if inner headers are not setFlorian Westphal
mpls_gso_segment() assumes skb_inner_network_header() returns a valid result: mpls_hlen = skb_inner_network_header(skb) - skb_network_header(skb); if (unlikely(!mpls_hlen || mpls_hlen % MPLS_HLEN)) goto out; if (unlikely(!pskb_may_pull(skb, mpls_hlen))) With syzbot reproducer, skb_inner_network_header() yields 0, skb_network_header() returns 108, so this will "pskb_may_pull(skb, -108)))" which triggers a newly added DEBUG_NET_WARN_ON_ONCE() check: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 5068 at include/linux/skbuff.h:2723 pskb_may_pull_reason include/linux/skbuff.h:2723 [inline] WARNING: CPU: 0 PID: 5068 at include/linux/skbuff.h:2723 pskb_may_pull include/linux/skbuff.h:2739 [inline] WARNING: CPU: 0 PID: 5068 at include/linux/skbuff.h:2723 mpls_gso_segment+0x773/0xaa0 net/mpls/mpls_gso.c:34 [..] skb_mac_gso_segment+0x383/0x740 net/core/gso.c:53 nsh_gso_segment+0x40a/0xad0 net/nsh/nsh.c:108 skb_mac_gso_segment+0x383/0x740 net/core/gso.c:53 __skb_gso_segment+0x324/0x4c0 net/core/gso.c:124 skb_gso_segment include/net/gso.h:83 [inline] [..] sch_direct_xmit+0x11a/0x5f0 net/sched/sch_generic.c:327 [..] packet_sendmsg+0x46a9/0x6130 net/packet/af_packet.c:3113 [..] First iteration of this patch made mpls_hlen signed and changed test to error out to "mpls_hlen <= 0 || ..". Eric Dumazet said: > I was thinking about adding a debug check in skb_inner_network_header() > if inner_network_header is zero (that would mean it is not 'set' yet), > but this would trigger even after your patch. So add new skb_inner_network_header_was_set() helper and use that. The syzbot reproducer injects data via packet socket. The skb that gets allocated and passed down the stack has ->protocol set to NSH (0x894f) and gso_type set to SKB_GSO_UDP | SKB_GSO_DODGY. This gets passed to skb_mac_gso_segment(), which sees NSH as ptype to find a callback for. nsh_gso_segment() retrieves next type: proto = tun_p_to_eth_p(nsh_hdr(skb)->np); ... which is MPLS (TUN_P_MPLS_UC). It updates skb->protocol and then calls mpls_gso_segment(). Inner offsets are all 0, so mpls_gso_segment() ends up with a negative header size. In case more callers rely on silent handling of such large may_pull values we could also 'legalize' this behaviour, either replacing the debug check with (len > INT_MAX) test or removing it and instead adding a comment before existing if (unlikely(len > skb->len)) return SKB_DROP_REASON_PKT_TOO_SMALL; test in pskb_may_pull_reason(), saying that this check also implicitly takes care of callers that miscompute header sizes. Cc: Simon Horman <horms@kernel.org> Fixes: 219eee9c0d16 ("net: skbuff: add overflow debug check to pull/push helpers") Reported-by: syzbot+99d15fcdb0132a1e1a82@syzkaller.appspotmail.com Closes: https://lore.kernel.org/netdev/00000000000043b1310611e388aa@google.com/raw Signed-off-by: Florian Westphal <fw@strlen.de> Link: https://lore.kernel.org/r/20240222140321.14080-1-fw@strlen.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-02-23net: ethtool: avoid rebuilds on UTS_RELEASE changeJann Horn
Currently, when you switch between branches or something like that and rebuild, net/ethtool/ioctl.c has to be built again because it depends on UTS_RELEASE. By instead referencing a string variable stored in another object file, this can be avoided. Signed-off-by: Jann Horn <jannh@google.com> Reviewed-by: John Garry <john.g.garry@oracle.com> Link: https://lore.kernel.org/r/20240220194244.2056384-1-jannh@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-02-23tun: Fix xdp_rxq_info's queue_index when detachingYunjian Wang
When a queue(tfile) is detached, we only update tfile's queue_index, but do not update xdp_rxq_info's queue_index. This patch fixes it. Fixes: 8bf5c4ee1889 ("tun: setup xdp_rxq_info") Signed-off-by: Yunjian Wang <wangyunjian@huawei.com> Link: https://lore.kernel.org/r/1708398727-46308-1-git-send-email-wangyunjian@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-02-23i2c: imx: when being a target, mark the last read as processedCorey Minyard
When being a target, NAK from the controller means that all bytes have been transferred. So, the last byte needs also to be marked as 'processed'. Otherwise index registers of backends may not increase. Fixes: f7414cd6923f ("i2c: imx: support slave mode for imx I2C driver") Signed-off-by: Corey Minyard <minyard@acm.org> Tested-by: Andrew Manley <andrew.manley@sealingtech.com> Reviewed-by: Andrew Manley <andrew.manley@sealingtech.com> Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de> [wsa: fixed comment and commit message to properly describe the case] Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
2024-02-23apparmor: fix lsm_get_self_attr()Mickaël Salaün
In apparmor_getselfattr() when an invalid AppArmor attribute is requested, or a value hasn't been explicitly set for the requested attribute, the label passed to aa_put_label() is not properly initialized which can cause problems when the pointer value is non-NULL and AppArmor attempts to drop a reference on the bogus label object. Cc: Casey Schaufler <casey@schaufler-ca.com> Cc: John Johansen <john.johansen@canonical.com> Fixes: 223981db9baf ("AppArmor: Add selfattr hooks") Signed-off-by: Mickaël Salaün <mic@digikod.net> Reviewed-by: Paul Moore <paul@paul-moore.com> [PM: description changes as discussed with MS] Signed-off-by: Paul Moore <paul@paul-moore.com>
2024-02-23selinux: fix lsm_get_self_attr()Mickaël Salaün
selinux_getselfattr() doesn't properly initialize the string pointer it passes to selinux_lsm_getattr() which can cause a problem when an attribute hasn't been explicitly set; selinux_lsm_getattr() returns 0/success, but does not set or initialize the string label/attribute. Failure to properly initialize the string causes problems later in selinux_getselfattr() when the function attempts to kfree() the string. Cc: Casey Schaufler <casey@schaufler-ca.com> Fixes: 762c934317e6 ("SELinux: Add selfattr hooks") Suggested-by: Paul Moore <paul@paul-moore.com> [PM: description changes as discussed in the thread] Signed-off-by: Mickaël Salaün <mic@digikod.net> Signed-off-by: Paul Moore <paul@paul-moore.com>
2024-02-23arm64: dts: allwinner: h616: Add Orange Pi Zero 2W to MakefileJernej Skrabec
Orange Pi Zero 2W dts file is not included in Makefile. Fix this. Fixes: c505ee1eae18 ("arm64: dts: allwinner: h616: add Orange Pi Zero 2W support") Reviewed-by: Andre Przywara <andre.przywara@arm.com> Link: https://lore.kernel.org/r/20240222211326.114955-1-jernej.skrabec@gmail.com Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
2024-02-23Merge tag 'parisc-for-6.8-rc6' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux Pull parisc architecture fixes from Helge Deller: "Fixes CPU hotplug, the parisc stack unwinder and two possible build errors in kprobes and ftrace area: - Fix CPU hotplug - Fix unaligned accesses and faults in stack unwinder - Fix potential build errors by always including asm-generic/kprobes.h - Fix build bug by add missing CONFIG_DYNAMIC_FTRACE check" * tag 'parisc-for-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux: parisc: Fix stack unwinder parisc/kprobes: always include asm-generic/kprobes.h parisc/ftrace: add missing CONFIG_DYNAMIC_FTRACE check Revert "parisc: Only list existing CPUs in cpu_possible_mask"
2024-02-23Merge tag 'arm-fixes-6.8-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull arm and RISC-V SoC fixes from Arnd Bergmann: "The Rockchip and IMX8 platforms get a number of fixes for dts files in order to address some misconfigurations, including a regression for USB-C support on some boards. The other dts fixes are part of a series by Rob Herring to clean up another class of dtc compiler warnings across all platforms, with a few others helping out as well. With this, we can enable the warning for the coming merge window without introducing regressions. Conor Dooley has collected fixes for RISC-V platforms, both for the dts files and for platofrm specific drivers. The ep93xx platform gets a regression for for its gpio descriptors" * tag 'arm-fixes-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (28 commits) ARM: dts: renesas: rcar-gen2: Add missing #interrupt-cells to DA9063 nodes cache: ax45mp_cache: Align end size to cache boundary in ax45mp_dma_cache_wback() arm64: dts: qcom: Fix interrupt-map cell sizes arm: dts: Fix dtc interrupt_map warnings arm64: dts: Fix dtc interrupt_provider warnings arm: dts: Fix dtc interrupt_provider warnings arm64: dts: freescale: Disable interrupt_map check ARM: ep93xx: Add terminator to gpiod_lookup_table riscv: dts: sifive: add missing #interrupt-cells to pmic arm64: dts: rockchip: Correct Indiedroid Nova GPIO Names arm64: dts: rockchip: Drop interrupts property from rk3328 pwm-rockchip node arm64: dts: rockchip: set num-cs property for spi on px30 arm64: dts: rockchip: minor rk3588 whitespace cleanup riscv: dts: starfive: replace underscores in node names bus: imx-weim: fix valid range check Revert "arm64: dts: imx8mn-var-som-symphony: Describe the USB-C connector" Revert "arm64: dts: imx8mp-dhcom-pdk3: Describe the USB-C connector" arm64: dts: tqma8mpql: fix audio codec iov-supply arm64: dts: rockchip: drop unneeded status from rk3588-jaguar gpio-leds ARM: dts: rockchip: Drop interrupts property from pwm-rockchip nodes ...
2024-02-23Merge tag 'arm64-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux Pull arm64 fixes from Will Deacon: "A simple fix to a definition in the CXL PMU driver, a couple of patches to restore SME control registers on the resume path (since Arm's fast model now clears them) and a revert for our jump label asm constraints after Geert noticed they broke the build with GCC 5.5. There was then the ensuing discussion about raising the minimum GCC (and corresponding binutils) versions at [1], but for now we'll keep things working as they were until that goes ahead. - Revert fix to jump label asm constraints, as it regresses the build with some GCC 5.5 toolchains. - Restore SME control registers when resuming from suspend - Fix incorrect filter definition in CXL PMU driver" * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: arm64/sme: Restore SMCR_EL1.EZT0 on exit from suspend arm64/sme: Restore SME registers on exit from suspend Revert "arm64: jump_label: use constraints "Si" instead of "i"" perf: CXL: fix CPMU filter value mask length
2024-02-23Merge tag 's390-6.8-3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux Pull s390 fixes from Heiko Carstens: - Fix invalid -EBUSY on ccw_device_start() which can lead to failing device initialization - Add missing multiplication by 8 in __iowrite64_copy() to get the correct byte length before calling zpci_memcpy_toio() - Various config updates * tag 's390-6.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: s390/cio: fix invalid -EBUSY on ccw_device_start s390: use the correct count for __iowrite64_copy() s390/configs: update default configurations s390/configs: enable INIT_STACK_ALL_ZERO in all configurations s390/configs: provide compat topic configuration target
2024-02-23Merge tag 'mm-hotfixes-stable-2024-02-22-15-02' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm Pull misc fixes from Andrew Morton: "A batch of MM (and one non-MM) hotfixes. Ten are cc:stable and the remainder address post-6.7 issues or aren't considered appropriate for backporting" * tag 'mm-hotfixes-stable-2024-02-22-15-02' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: kasan: guard release_free_meta() shadow access with kasan_arch_is_ready() mm/damon/lru_sort: fix quota status loss due to online tunings mm/damon/reclaim: fix quota stauts loss due to online tunings MAINTAINERS: mailmap: update Shakeel's email address mm/damon/sysfs-schemes: handle schemes sysfs dir removal before commit_schemes_quota_goals mm: memcontrol: clarify swapaccount=0 deprecation warning mm/memblock: add MEMBLOCK_RSRV_NOINIT into flagname[] array mm/zswap: invalidate duplicate entry when !zswap_enabled lib/Kconfig.debug: TEST_IOV_ITER depends on MMU mm/swap: fix race when skipping swapcache mm/swap_state: update zswap LRU's protection range with the folio locked selftests/mm: uffd-unit-test check if huge page size is 0 mm/damon/core: check apply interval in damon_do_apply_schemes() mm: zswap: fix missing folio cleanup in writeback race path
2024-02-23Merge tag 'for-6.8/dm-fixes-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm Pull device mapper fixes from Mike Snitzer: - Stable fixes for 3 DM targets (integrity, verity and crypt) to address systemic failure that can occur if user provided pages map to the same block. - Fix DM crypt to not allow modifying data that being encrypted for authenticated encryption. - Fix DM crypt and verity targets to align their respective bvec_iter struct members to avoid the need for byte level access (due to __packed attribute) that is costly on some arches (like RISC). * tag 'for-6.8/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: dm-crypt, dm-integrity, dm-verity: bump target version dm-verity, dm-crypt: align "struct bvec_iter" correctly dm-crypt: recheck the integrity tag after a failure dm-crypt: don't modify the data when using authenticated encryption dm-verity: recheck the hash after a failure dm-integrity: recheck the integrity tag after a failure
2024-02-23Merge tag 'drm-fixes-2024-02-23' of git://anongit.freedesktop.org/drm/drmLinus Torvalds
Pull drm fixes from Dave Airlie: "This is the weekly drm fixes. Non-drivers there is a fbdev/sparc fix, syncobj, ttm and buddy fixes. On the driver side, ivpu, meson, i915 have a small fix each. Then amdgpu and xe have a bunch. Nouveau has some minor uapi additions to give userspace some useful info along with a Kconfig change to allow the new GSP firmware paths to be used by default on the GPUs it supports. Seems about the usual amount for this time of release cycle. fbdev: - fix sparc undefined reference syncobj: - fix sync obj fence waiting - handle NULL fence in syncobj eventfd code ttm: - fix invalid free buddy: - fix list handling - fix 32-bit build meson: - don't remove bridges from other drivers nouveau: - fix build warnings - add two minor info parameters - add a Kconfig to allow GSP by default on some GPUs ivpu: - allow fw to do initial tile config i915: - fix TV mode amdgpu: - Suspend/resume fixes - Backlight error fix - DCN 3.5 fixes - Misc fixes xe: - Remove support for persistent exec_queues - Drop a reduntant sysfs newline printout - A three-patch fix for a VM_BIND rebind optimization path - Fix a modpost warning on an xe KUNIT module" * tag 'drm-fixes-2024-02-23' of git://anongit.freedesktop.org/drm/drm: (27 commits) nouveau: add an ioctl to report vram usage nouveau: add an ioctl to return vram bar size. nouveau/gsp: add kconfig option to enable GSP paths by default drm/amdgpu: Fix the runtime resume failure issue drm/amd/display: fix null-pointer dereference on edid reading drm/amd/display: Fix memory leak in dm_sw_fini() drm/amd/display: fix input states translation error for dcn35 & dcn351 drm/amd/display: Fix potential null pointer dereference in dc_dmub_srv drm/amd/display: Only allow dig mapping to pwrseq in new asic drm/amd/display: adjust few initialization order in dm drm/syncobj: handle NULL fence in syncobj_eventfd_entry_func drm/syncobj: call drm_syncobj_fence_add_wait when WAIT_AVAILABLE flag is set drm/ttm: Fix an invalid freeing on already freed page in error path sparc: Fix undefined reference to fb_is_primary_device drm/xe: Fix modpost warning on xe_mocs kunit module drm/xe/xe_gt_idle: Drop redundant newline in name drm/xe: Return 2MB page size for compact 64k PTEs drm/xe: Add XE_VMA_PTE_64K VMA flag drm/xe: Fix xe_vma_set_pte_size drm/xe/uapi: Remove support for persistent exec_queues ...
2024-02-23Merge tag 'ata-6.8-rc6' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux Pull ata fixes from Niklas Cassel: - Do not try to set a sleeping device to standby. Sleep is a deeper sleep state than standby, and needs a reset to wake up the drive. A system resume will reset the port. Sending a command other than reset to a sleeping device is not wise, as the command will timeout (Damien Le Moal) - Do not try to put a device to standby twice during system shutdown. ata_dev_power_set_standby() is currently called twice during shutdown, once after the scsi device is removed, and another when ata_pci_shutdown_one() executes. Modify ata_dev_power_set_standby() to do nothing if the device is already in standby (Damien Le Moal) - Add a quirk for ASM1064 to fixup the number of implemented ports. We probe all ports that the hardware reports to be implemented. Probing ports that are not implemented causes significantly increased boot time (Andrey Jr. Melnikov) - Fix error handling for the ahci_ceva driver. Ensure that the ahci_ceva driver does a proper cleanup of its resources in the error path (Radhey Shyam Pandey) * tag 'ata-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux: ata: libata-core: Do not call ata_dev_power_set_standby() twice ata: ahci_ceva: fix error handling for Xilinx GT PHY support ahci: asm1064: correct count of reported ports ata: libata-core: Do not try to set sleeping devices to standby
2024-02-23Merge tag 'gpio-fixes-for-v6.8-rc6' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux Pull gpio fix from Bartosz Golaszewski: - fix a use-case where no pins are mapped to GPIOs in gpiochip_generic_config() * tag 'gpio-fixes-for-v6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: gpiolib: Handle no pin_ranges in gpiochip_generic_config()
2024-02-23RISC-V: Ignore V from the riscv,isa DT property on older T-Head CPUsConor Dooley
Before attempting to support the pre-ratification version of vector found on older T-Head CPUs, disallow "v" in riscv,isa on these platforms. The deprecated property has no clear way to communicate the specific version of vector that is supported and much of the vendor provided software puts "v" in the isa string. riscv,isa-extensions should be used instead. This should not be too much of a burden for these systems, as the vendor shipped devicetrees and firmware do not work with a mainline kernel and will require updating. We can limit this restriction to only ignore v in riscv,isa on CPUs that report T-Head's vendor ID and a zero marchid. Newer T-Head CPUs that support the ratified version of vector should report non-zero marchid, according to Guo Ren [1]. Link: https://lore.kernel.org/linux-riscv/CAJF2gTRy5eK73=d6s7CVy9m9pB8p4rAoMHM3cZFwzg=AuF7TDA@mail.gmail.com/ [1] Fixes: dc6667a4e7e3 ("riscv: Extending cpufeature.c to detect V-extension") Co-developed-by: Conor Dooley <conor.dooley@microchip.com> Signed-off-by: Conor Dooley <conor.dooley@microchip.com> Acked-by: Guo Ren <guoren@kernel.org> Link: https://lore.kernel.org/r/20240223-tidings-shabby-607f086cb4d7@spud Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2024-02-23Merge tag 'hwmon-for-v6.8-rc6' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging Pull hwmon fix from Guenter Roeck: "Fix a global-out-of-bounds bug in nct6775 driver" * tag 'hwmon-for-v6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: hwmon: (nct6775) Fix access to temperature configuration registers
2024-02-23dt-bindings: net: wireless: qcom: Update maintainersJeff Johnson
Add Jeff Johnson as a maintainer of the qcom,ath1*k.yaml files. Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240217-ath1xk-maintainer-v1-1-9f7ff5fb6bf4@quicinc.com
2024-02-23wifi: ath11k: thermal: don't try to register multiple timesKalle Valo
Every time the firmware boots we call ath11k_core_qmi_firmware_ready() which ends up calling ath11k_thermal_register(). So we try to register thermal devices multiple times. And when we power off the firmware during suspend/hibernation (implemented in the next patch) we get a warning in resume: hwmon hwmon4: PM: parent phy0 should not be sleeping Workaround this similarly like ath11k_mac_register() does by testing ATH11K_FLAG_REGISTERED. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30 Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Link: https://msgid.link/20240221024725.10057-6-quic_bqiang@quicinc.com
2024-02-23wifi: ath11k: fix warning on DMA ring capabilities eventBaochen Qiang
We are seeing below warning in both reset and suspend/resume scenarios: [69663.691847] ath11k_pci 0000:02:00.0: Already processed, so ignoring dma ring caps This is because ab->num_db_cap is not cleared in ath11k_wmi_free_dbring_caps(), so clear it to avoid such warnings. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30 Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Link: https://msgid.link/20240221024725.10057-5-quic_bqiang@quicinc.com
2024-02-23wifi: ath11k: do not dump SRNG statistics during resumeBaochen Qiang
Both the firmware reset feature and the power management suspend/resume feature share common power-down and power-up functionality. One aspect of the power-up functionality is the handling of the ATH11K_QMI_EVENT_FW_INIT_DONE event. When this event is received, a call is made to ath11k_hal_dump_srng_stats(), with the purpose to collect information that may be useful in debugging the cause of a firmware reset. Unfortunately, since this functionality is shared between both the firmware reset path and the power management resume path, the kernel log is flooded with messages during resume. Since these messages are not useful during resume, and in fact can be confusing and can increase the time it takes to resume, update the logic to only call ath11k_hal_dump_srng_stats() during firmware reset. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30 Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Link: https://msgid.link/20240221024725.10057-4-quic_bqiang@quicinc.com
2024-02-23wifi: ath11k: remove MHI LOOPBACK channelsBaochen Qiang
There is no driver to match these two channels, so remove them. This fixes warnings from MHI subsystem during suspend: mhi mhi0_LOOPBACK: 1: Failed to reset channel, still resetting mhi mhi0_LOOPBACK: 0: Failed to reset channel, still resetting Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30 Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Link: https://msgid.link/20240221024725.10057-3-quic_bqiang@quicinc.com
2024-02-23wifi: ath11k: rearrange IRQ enable/disable in reset pathBaochen Qiang
For non WoW suspend/resume, ath11k host powers down whole hardware when suspend and powers up it when resume, the code path it goes through is very like the ath11k reset logic. In order to reuse that logic, rearrange IRQ handling in the reset path. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30 Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Link: https://msgid.link/20240221024725.10057-2-quic_bqiang@quicinc.com
2024-02-23iommu/sva: Restore SVA handle sharingJason Gunthorpe
Prior to commit 092edaddb660 ("iommu: Support mm PASID 1:n with sva domains") the code allowed a SVA handle to be bound multiple times to the same (mm, device) pair. This was alluded to in the kdoc comment, but we had understood this to be more a remark about allowing multiple devices, not a literal same-driver re-opening the same SVA. It turns out uacce and idxd were both relying on the core code to handle reference counting for same-device same-mm scenarios. As this looks hard to resolve in the drivers bring it back to the core code. The new design has changed the meaning of the domain->users refcount to refer to the number of devices that are sharing that domain for the same mm. This is part of the design to lift the SVA domain de-duplication out of the drivers. Return the old behavior by explicitly de-duplicating the struct iommu_sva handle. The same (mm, device) will return the same handle pointer and the core code will handle tracking this. The last unbind of the handle will destroy it. Fixes: 092edaddb660 ("iommu: Support mm PASID 1:n with sva domains") Reported-by: Zhangfei Gao <zhangfei.gao@linaro.org> Closes: https://lore.kernel.org/all/20240221110658.529-1-zhangfei.gao@linaro.org/ Tested-by: Zhangfei Gao <zhangfei.gao@linaro.org> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com> Link: https://lore.kernel.org/r/0-v1-9455fc497a6f+3b4-iommu_sva_sharing_jgg@nvidia.com Signed-off-by: Joerg Roedel <jroedel@suse.de>
2024-02-23Merge tag 'arm-smmu-fixes' of ↵Joerg Roedel
git://git.kernel.org/pub/scm/linux/kernel/git/will/linux into iommu/fixes Arm SMMU fixes for 6.8 - Fix CD allocation from atomic context when using SVA with SMMUv3 - Revert the conversion of SMMUv2 to domain_alloc_paging(), as it breaks the boot for Qualcomm MSM8996 devices
2024-02-23soc: qcom: pmic_glink: Fix boot when QRTR=mRob Clark
We need to bail out before adding/removing devices if we are going to -EPROBE_DEFER. Otherwise boot can get stuck in a probe deferral loop due to a long-standing issue in driver core (see commit fbc35b45f9f6 ("Add documentation on meaning of -EPROBE_DEFER")). Deregistering the altmode child device can potentially also trigger bugs in the DRM bridge implementation, which does not expect bridges to go away. [DB: slightly fixed commit message by adding the word 'commit'] Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Link: https://lore.kernel.org/r/20231213210644.8702-1-robdclark@gmail.com [ johan: rebase on 6.8-rc4, amend commit message and mention DRM ] Fixes: 58ef4ece1e41 ("soc: qcom: pmic_glink: Introduce base PMIC GLINK driver") Cc: <stable@vger.kernel.org> # 6.3 Cc: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Bjorn Andersson <andersson@kernel.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240217150228.5788-5-johan+linaro@kernel.org
2024-02-23soc: qcom: pmic_glink_altmode: fix drm bridge use-after-freeJohan Hovold
A recent DRM series purporting to simplify support for "transparent bridges" and handling of probe deferrals ironically exposed a use-after-free issue on pmic_glink_altmode probe deferral. This has manifested itself as the display subsystem occasionally failing to initialise and NULL-pointer dereferences during boot of machines like the Lenovo ThinkPad X13s. Specifically, the dp-hpd bridge is currently registered before all resources have been acquired which means that it can also be deregistered on probe deferrals. In the meantime there is a race window where the new aux bridge driver (or PHY driver previously) may have looked up the dp-hpd bridge and stored a (non-reference-counted) pointer to the bridge which is about to be deallocated. When the display controller is later initialised, this triggers a use-after-free when attaching the bridges: dp -> aux -> dp-hpd (freed) which may, for example, result in the freed bridge failing to attach: [drm:drm_bridge_attach [drm]] *ERROR* failed to attach bridge /soc@0/phy@88eb000 to encoder TMDS-31: -16 or a NULL-pointer dereference: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 ... Call trace: drm_bridge_attach+0x70/0x1a8 [drm] drm_aux_bridge_attach+0x24/0x38 [aux_bridge] drm_bridge_attach+0x80/0x1a8 [drm] dp_bridge_init+0xa8/0x15c [msm] msm_dp_modeset_init+0x28/0xc4 [msm] The DRM bridge implementation is clearly fragile and implicitly built on the assumption that bridges may never go away. In this case, the fix is to move the bridge registration in the pmic_glink_altmode driver to after all resources have been looked up. Incidentally, with the new dp-hpd bridge implementation, which registers child devices, this is also a requirement due to a long-standing issue in driver core that can otherwise lead to a probe deferral loop (see commit fbc35b45f9f6 ("Add documentation on meaning of -EPROBE_DEFER")). [DB: slightly fixed commit message by adding the word 'commit'] Fixes: 080b4e24852b ("soc: qcom: pmic_glink: Introduce altmode support") Fixes: 2bcca96abfbf ("soc: qcom: pmic-glink: switch to DRM_AUX_HPD_BRIDGE") Cc: <stable@vger.kernel.org> # 6.3 Cc: Bjorn Andersson <andersson@kernel.org> Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Bjorn Andersson <andersson@kernel.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240217150228.5788-4-johan+linaro@kernel.org
2024-02-23drm/bridge: aux-hpd: separate allocation and registrationJohan Hovold
Combining allocation and registration is an anti-pattern that should be avoided. Add two new functions for allocating and registering an dp-hpd bridge with a proper 'devm' prefix so that it is clear that these are device managed interfaces. devm_drm_dp_hpd_bridge_alloc() devm_drm_dp_hpd_bridge_add() The new interface will be used to fix a use-after-free bug in the Qualcomm PMIC GLINK driver and may prevent similar issues from being introduced elsewhere. The existing drm_dp_hpd_bridge_register() is reimplemented using the above and left in place for now. Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Bjorn Andersson <andersson@kernel.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240217150228.5788-3-johan+linaro@kernel.org
2024-02-23ASoC: soc-card: Fix missing locking in snd_soc_card_get_kcontrol()Richard Fitzgerald
snd_soc_card_get_kcontrol() must be holding a read lock on card->controls_rwsem while walking the controls list. Compare with snd_ctl_find_numid(). The existing function is renamed snd_soc_card_get_kcontrol_locked() so that it can be called from contexts that are already holding card->controls_rwsem (for example, control get/put functions). There are few direct or indirect callers of snd_soc_card_get_kcontrol(), and most are safe. Three require changes, which have been included in this patch: codecs/cs35l45.c: cs35l45_activate_ctl() is called from a control put() function so is changed to call snd_soc_card_get_kcontrol_locked(). codecs/cs35l56.c: cs35l56_sync_asp1_mixer_widgets_with_firmware() is called from control get()/put() functions so is changed to call snd_soc_card_get_kcontrol_locked(). fsl/fsl_xcvr.c: fsl_xcvr_activate_ctl() is called from three places, one of which already holds card->controls_rwsem: 1. fsl_xcvr_mode_put(), a control put function, which will already be holding card->controls_rwsem. 2. fsl_xcvr_startup(), a DAI startup function. 3. fsl_xcvr_shutdown(), a DAI shutdown function. To fix this, fsl_xcvr_activate_ctl() has been changed to call snd_soc_card_get_kcontrol_locked() so that it is safe to call directly from fsl_xcvr_mode_put(). The fsl_xcvr_startup() and fsl_xcvr_shutdown() functions have been changed to take a read lock on card->controls_rsem() around calls to fsl_xcvr_activate_ctl(). While this is not very elegant, it keeps the change small, to avoid this patch creating a large collateral churn in fsl/fsl_xcvr.c. Analysis of other callers of snd_soc_card_get_kcontrol() is that they do not need any changes, they are not holding card->controls_rwsem when they call snd_soc_card_get_kcontrol(). Direct callers of snd_soc_card_get_kcontrol(): fsl/fsl_spdif.c: fsl_spdif_dai_probe() - DAI probe function fsl/fsl_micfil.c: voice_detected_fn() - IRQ handler Indirect callers via soc_component_notify_control(): codecs/cs42l43: cs42l43_mic_shutter() - IRQ handler codecs/cs42l43: cs42l43_spk_shutter() - IRQ handler codecs/ak4118.c: ak4118_irq_handler() - IRQ handler codecs/wm_adsp.c: wm_adsp_write_ctl() - not currently used Indirect callers via snd_soc_limit_volume(): qcom/sc8280xp.c: sc8280xp_snd_init() - DAIlink init function ti/rx51.c: rx51_aic34_init() - DAI init function I don't have hardware to test the fsl/*, qcom/sc828xp.c, ti/rx51.c and ak4118.c changes. Backport note: The fsl/, qcom/, cs35l45, cs35l56 and cs42l43 callers were added since the Fixes commit so won't all be present on older kernels. Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Fixes: 209c6cdfd283 ("ASoC: soc-card: move snd_soc_card_get_kcontrol() to soc-card") Link: https://lore.kernel.org/r/20240221123710.690224-1-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org>
2024-02-23ALSA: hda/realtek: tas2781: enable subwoofer volume controlGergo Koteles
The volume of subwoofer channels is always at maximum with the ALC269_FIXUP_THINKPAD_ACPI chain. Use ALC285_FIXUP_THINKPAD_HEADSET_JACK to align it to the master volume. Link: https://bugzilla.kernel.org/show_bug.cgi?id=208555#c827 Fixes: 3babae915f4c ("ALSA: hda/tas2781: Add tas2781 HDA driver") Cc: <stable@vger.kernel.org> Signed-off-by: Gergo Koteles <soyer@irl.hu> Link: https://lore.kernel.org/r/7ffae10ebba58601d25fe2ff8381a6ae3a926e62.1708687813.git.soyer@irl.hu Signed-off-by: Takashi Iwai <tiwai@suse.de>
2024-02-23Merge tag 'renesas-fixes-for-v6.8-tag1' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes Renesas fixes for v6.8 - Add missing #interrupt-cells to DA9063 nodes. * tag 'renesas-fixes-for-v6.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: ARM: dts: renesas: rcar-gen2: Add missing #interrupt-cells to DA9063 nodes Link: https://lore.kernel.org/r/cover.1708597150.git.geert+renesas@glider.be Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2024-02-23Merge tag 'riscv-dt-fixes-for-v6.8-rc6' of ↵Arnd Bergmann
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into arm/fixes RISC-V Devicetree fixes for v6.8-rc6 Two fixes for W=2 issues in devicetrees, which should constitute fixes for all reasonable-to-fix W=2 problems on RISC-V. The others are caused by standard USB and MMC property names containing underscores that are not likely to ever change. Signed-off-by: Conor Dooley <conor.dooley@microchip.com> * tag 'riscv-dt-fixes-for-v6.8-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux: riscv: dts: sifive: add missing #interrupt-cells to pmic riscv: dts: starfive: replace underscores in node names Link: https://lore.kernel.org/r/20240221-foil-glade-09dbf1aa3fe2@spud Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2024-02-23Merge tag 'riscv-soc-drivers-fixes-for-v6.8-rc6' of ↵Arnd Bergmann
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into arm/fixes RISC-V SoC driver fixes for v6.8-rc6 A fix for a kconfig symbol whose help text has been unhelpful since its introduction. Signed-off-by: Conor Dooley <conor.dooley@microchip.com> * tag 'riscv-soc-drivers-fixes-for-v6.8-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux: soc: microchip: Fix POLARFIRE_SOC_SYS_CTRL input prompt Link: https://lore.kernel.org/r/20240221-irate-outrage-cf7f96f83074@spud Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2024-02-23Merge tag 'riscv-firmware-fixes-for-v6.8-rc6' of ↵Arnd Bergmann
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into arm/fixes Microchip firmware driver fixes for v6.8-rc6 A single fix for me incorrectly using sizeof(). Signed-off-by: Conor Dooley <conor.dooley@microchip.com> * tag 'riscv-firmware-fixes-for-v6.8-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux: firmware: microchip: fix wrong sizeof argument Link: https://lore.kernel.org/r/20240221-recognize-dust-4bb575f4e67b@spud Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2024-02-23Merge tag 'riscv-cache-fixes-for-v6.8-rc6' of ↵Arnd Bergmann
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into arm/fixes RISC-V Cache driver fixes for v6.8-rc6 A single fix for an inconsistency reported during CIP review by Pavel in the newly added ax45mp cache driver. Signed-off-by: Conor Dooley <conor.dooley@microchip.com> * tag 'riscv-cache-fixes-for-v6.8-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux: cache: ax45mp_cache: Align end size to cache boundary in ax45mp_dma_cache_wback() Link: https://lore.kernel.org/r/20240221-keenness-handheld-b930aaa77708@spud Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2024-02-23ps3/gelic: Fix SKB allocationGeoff Levand
Commit 3ce4f9c3fbb3 ("net/ps3_gelic_net: Add gelic_descr structures") of 6.8-rc1 had a copy-and-paste error where the pointer that holds the allocated SKB (struct gelic_descr.skb) was set to NULL after the SKB was allocated. This resulted in a kernel panic when the SKB pointer was accessed. This fix moves the initialization of the gelic_descr to before the SKB is allocated. Reported-by: sambat goson <sombat3960@gmail.com> Fixes: 3ce4f9c3fbb3 ("net/ps3_gelic_net: Add gelic_descr structures") Signed-off-by: Geoff Levand <geoff@infradead.org> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-02-23net: dpaa: fman_memac: accept phy-interface-type = "10gbase-r" in the device ↵Vladimir Oltean
tree Since commit 5d93cfcf7360 ("net: dpaa: Convert to phylink"), we support the "10gbase-r" phy-mode through a driver-based conversion of "xgmii", but we still don't actually support it when the device tree specifies "10gbase-r" proper. This is because boards such as LS1046A-RDB do not define pcs-handle-names (for whatever reason) in the ethernet@f0000 device tree node, and the code enters through this code path: err = of_property_match_string(mac_node, "pcs-handle-names", "xfi"); // code takes neither branch and falls through if (err >= 0) { (...) } else if (err != -EINVAL && err != -ENODATA) { goto _return_fm_mac_free; } (...) /* For compatibility, if pcs-handle-names is missing, we assume this * phy is the first one in pcsphy-handle */ err = of_property_match_string(mac_node, "pcs-handle-names", "sgmii"); if (err == -EINVAL || err == -ENODATA) pcs = memac_pcs_create(mac_node, 0); // code takes this branch else if (err < 0) goto _return_fm_mac_free; else pcs = memac_pcs_create(mac_node, err); // A default PCS is created and saved in "pcs" // This determination fails and mistakenly saves the default PCS // memac->sgmii_pcs instead of memac->xfi_pcs, because at this // stage, mac_dev->phy_if == PHY_INTERFACE_MODE_10GBASER. if (err && mac_dev->phy_if == PHY_INTERFACE_MODE_XGMII) memac->xfi_pcs = pcs; else memac->sgmii_pcs = pcs; In other words, in the absence of pcs-handle-names, the default xfi_pcs assignment logic only works when in the device tree we have PHY_INTERFACE_MODE_XGMII. By reversing the order between the fallback xfi_pcs assignment and the "xgmii" overwrite with "10gbase-r", we are able to support both values in the device tree, with identical behavior. Currently, it is impossible to make the s/xgmii/10gbase-r/ device tree conversion, because it would break forward compatibility (new device tree with old kernel). The only way to modify existing device trees to phy-interface-mode = "10gbase-r" is to fix stable kernels to accept this value and handle it properly. One reason why the conversion is desirable is because with pre-phylink kernels, the Aquantia PHY driver used to warn about the improper use of PHY_INTERFACE_MODE_XGMII [1]. It is best to have a single (latest) device tree that works with all supported stable kernel versions. Note that the blamed commit does not constitute a regression per se. Older stable kernels like 6.1 still do not work with "10gbase-r", but for a different reason. That is a battle for another time. [1] https://lore.kernel.org/netdev/20240214-ls1046-dts-use-10gbase-r-v1-1-8c2d68547393@concurrent-rt.com/ Fixes: 5d93cfcf7360 ("net: dpaa: Convert to phylink") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Sean Anderson <sean.anderson@seco.com> Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-02-23drm/bridge: aux-hpd: fix OF node leaksJohan Hovold
The two device node references taken during allocation need to be dropped when the auxiliary device is freed. Fixes: 6914968a0b52 ("drm/bridge: properly refcount DT nodes in aux bridge drivers") Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Cc: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20240217150228.5788-2-johan+linaro@kernel.org Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240217150228.5788-2-johan+linaro@kernel.org
2024-02-23net: stmmac: dwmac-qcom-ethqos: Add support for 2.5G SGMIISneh Shah
Serdes phy needs to operate at 2500 mode for 2.5G speed and 1000 mode for 1G/100M/10M speed. Added changes to configure serdes phy and mac based on link speed. Changing serdes phy speed involves multiple register writes for serdes block. To avoid redundant write operations only update serdes phy when new speed is different. For 2500 speed MAC PCS autoneg needs to disabled. Added changes to disable MAC PCS autoneg if ANE parameter is not set. Signed-off-by: Sneh Shah <quic_snehshah@quicinc.com> Tested-by: Abhishek Chauhan <quic_abchauha@quicinc.com> # sa8775p-ride Reviewed-by: Abhishek Chauhan <quic_abchauha@quicinc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-02-23ALSA: pcm: clarify and fix default msbits value for all formatsJaroslav Kysela
Return used most significant bits from sample bit-width rather than the whole physical sample word size. The starting bit offset is defined in the format itself. The behaviour is not changed for 32-bit formats like S32_LE. But with this change - msbits value 24 instead 32 is returned for 24-bit formats like S24_LE etc. Also, commit 2112aa034907 ("ALSA: pcm: Introduce MSBITS subformat interface") compares sample bit-width not physical sample bit-width to reset MSBITS_MAX bit from the subformat bitmask. Probably no applications are using msbits value for other than S32_LE/U32_LE formats, because no drivers are reducing msbits value for other formats (with the msb offset) at the moment. For sanity, increase PCM protocol version, letting the user space to detect the changed behaviour. Signed-off-by: Jaroslav Kysela <perex@perex.cz> Link: https://lore.kernel.org/r/20240222173649.1447549-1-perex@perex.cz Signed-off-by: Takashi Iwai <tiwai@suse.de>
2024-02-23wifi: mac80211: only call drv_sta_rc_update for uploaded stationsFelix Fietkau
When a station has not been uploaded yet, receiving SMPS or channel width notification action frames can lead to rate_control_rate_update calling drv_sta_rc_update with uninitialized driver private data. Fix this by adding a missing check for sta->uploaded. Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://msgid.link/20240221140535.16102-1-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2024-02-23dmaengine: ptdma: use consistent DMA masksTadeusz Struk
The PTDMA driver sets DMA masks in two different places for the same device inconsistently. First call is in pt_pci_probe(), where it uses 48bit mask. The second call is in pt_dmaengine_register(), where it uses a 64bit mask. Using 64bit dma mask causes IO_PAGE_FAULT errors on DMA transfers between main memory and other devices. Without the extra call it works fine. Additionally the second call doesn't check the return value so it can silently fail. Remove the superfluous dma_set_mask() call and only use 48bit mask. Cc: stable@vger.kernel.org Fixes: b0b4a6b10577 ("dmaengine: ptdma: register PTDMA controller as a DMA resource") Reviewed-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com> Signed-off-by: Tadeusz Struk <tstruk@gigaio.com> Link: https://lore.kernel.org/r/20240222163053.13842-1-tstruk@gigaio.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2024-02-23dmaengine: fsl-qdma: add __iomem and struct in union to fix sparse warningFrank Li
Fix below sparse warnings. drivers/dma/fsl-qdma.c:645:50: sparse: warning: incorrect type in argument 2 (different address spaces) drivers/dma/fsl-qdma.c:645:50: sparse: expected void [noderef] __iomem *addr drivers/dma/fsl-qdma.c:645:50: sparse: got void drivers/dma/fsl-qdma.c:387:15: sparse: sparse: restricted __le32 degrades to integer drivers/dma/fsl-qdma.c:390:19: sparse: expected restricted __le64 [usertype] data drivers/dma/fsl-qdma.c:392:13: sparse: expected unsigned int [assigned] [usertype] cmd QDMA decriptor have below 3 kind formats. (little endian) Compound Command Descriptor Format ┌──────┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┐ │Offset│3│3│2│2│2│2│2│2│2│2│2│2│1│1│1│1│1│1│1│1│1│1│ │ │ │ │ │ │ │ │ │ │ │ │1│0│9│8│7│6│5│4│3│2│1│0│9│8│7│6│5│4│3│2│1│0│9│8│7│6│5│4│3│2│1│0│ ├──────┼─┴─┼─┴─┴─┼─┴─┴─┼─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┼─┴─┴─┴─┴─┴─┴─┴─┤ │ 0x0C │DD │ - │QUEUE│ - │ ADDR │ ├──────┼───┴─────┴─────┴───────────────────────────────┴───────────────┤ │ 0x08 │ ADDR │ ├──────┼─────┬─────────────────┬───────────────────────────────────────┤ │ 0x04 │ FMT │ OFFSET │ - │ ├──────┼─┬─┬─┴─────────────────┴───────────────────────┬───────────────┤ │ │ │S│ │ │ │ 0x00 │-│E│ - │ STATUS │ │ │ │R│ │ │ └──────┴─┴─┴───────────────────────────────────────────┴───────────────┘ Compound S/G Table Entry Format ┌──────┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┐ │Offset│3│3│2│2│2│2│2│2│2│2│2│2│1│1│1│1│1│1│1│1│1│1│ │ │ │ │ │ │ │ │ │ │ │ │1│0│9│8│7│6│5│4│3│2│1│0│9│8│7│6│5│4│3│2│1│0│9│8│7│6│5│4│3│2│1│0│ ├──────┼─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┼─┴─┴─┴─┴─┴─┴─┴─┤ │ 0x0C │ - │ ADDR │ ├──────┼───────────────────────────────────────────────┴───────────────┤ │ 0x08 │ ADDR │ ├──────┼─┬─┬───────────────────────────────────────────────────────────┤ │ 0x04 │E│F│ LENGTH │ ├──────┼─┴─┴─────────────────────────────────┬─────────────────────────┤ │ 0x00 │ - │ OFFSET │ └──────┴─────────────────────────────────────┴─────────────────────────┘ Source/Destination Descriptor Format ┌──────┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┬─┐ │Offset│3│3│2│2│2│2│2│2│2│2│2│2│1│1│1│1│1│1│1│1│1│1│ │ │ │ │ │ │ │ │ │ │ │ │1│0│9│8│7│6│5│4│3│2│1│0│9│8│7│6│5│4│3│2│1│0│9│8│7│6│5│4│3│2│1│0│ ├──────┼─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┴─┤ │ 0x0C │ CMD │ ├──────┼───────────────────────────────────────────────────────────────┤ │ 0x08 │ - │ ├──────┼───────────────┬───────────────────────┬───────────────────────┤ │ 0x04 │ - │ S[D]SS │ S[D]SD │ ├──────┼───────────────┴───────────────────────┴───────────────────────┤ │ 0x00 │ - │ └──────┴───────────────────────────────────────────────────────────────┘ Previous code use 64bit 'data' map to 0x8 and 0xC. In little endian system CMD is high part of 64bit 'data'. It is correct by left shift 32. But in big endian system, shift left 32 will write to 0x8 position. Sparse detect this problem. Add below field ot match 'Source/Destination Descriptor Format'. struct { __le32 __reserved2; __le32 cmd; } __packed; Using ddf(sdf)->cmd save to correct posistion regardless endian. Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202402081929.mggOTHaZ-lkp@intel.com/ Signed-off-by: Frank Li <Frank.Li@nxp.com> Link: https://lore.kernel.org/r/20240219155939.611237-1-Frank.Li@nxp.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2024-02-23LoongArch: KVM: Streamline kvm_check_cpucfg() and improve commentsWANG Xuerui
All the checks currently done in kvm_check_cpucfg can be realized with early returns, so just do that to avoid extra cognitive burden related to the return value handling. While at it, clean up comments of _kvm_get_cpucfg_mask() and kvm_check_cpucfg(), by removing comments that are merely restatement of the code nearby, and paraphrasing the rest so they read more natural for English speakers (that likely are not familiar with the actual Chinese- influenced grammar). No functional changes intended. Reviewed-by: Bibo Mao <maobibo@loongson.cn> Signed-off-by: WANG Xuerui <git@xen0n.name> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
generated by cgit (git 2.34.1) at 2025-09-15 23:53:13 +0000