| Age | Commit message (Collapse) | Author |
|---|
|
The allocated buffer was not freed if usb_submit_urb() failed.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds the device nodes for flexcan controller(s) present on
LS1021A-Rev2 SoC.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Sakar Arora <Sakar.Arora@freescale.com>
Reviewed-by: Zhengxiong Jin <Jason.Jin@freescale.com>
Reviewed-by: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The flexcan driver has been modified to check for big-endian dts
property for be read/write to flexcan registers/mb.
An exception to this rule is powerpc P1010RDB, which is always
big-endian, even if big-endian is not present in dts. This is
checked using p1010-flexcan compatible in dts.
Therefore, remove p1010-flexcan compatible from imx series dts,
as their flexcan core is little endian.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The flexcan driver assumed that flexcan controller is big endian for
powerpc architecture and little endian for other architectures.
But this is not universally true. flexcan controller can be little or
big endian on any architecture.
Therefore the flexcan driver has been modified to check for "big-endian"
device tree property for controllers that are big endian.
consequently add the property to freescale P1010 SOC device tree.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The FlexCAN controller can be modelled as little or big endian depending
on SOC design. This device tree property identifies the controller
endianness and the driver reads/writes controller registers based on
that.
This is optional property. i.e. if this property is not present in
device tree node then controller is assumed to be little endian. if this
property is present then controller is assumed to be big endian.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds platform specific details for NXP SOC LS1021A to the
flexcan driver code.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: Zhengxiong Jin <Jason.Jin@freescale.com>
Reviewed-by: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
controllers.
The FlexCAN driver assumed that FlexCAN controller is big endian for
powerpc architecture and little endian for other architectures.
But this may not be the case. FlexCAN controller can be little or big
endian on any architecture. For e.g. NXP LS1021A ARM based SOC has big
endian FlexCAN controller.
Therefore, the driver has been modified to add a provision for both
types of controllers using an additional device tree property. On a
"fsl,p1010-flexcan" device BE is default, on all other devices LE is.
Big Endian controllers should have "big-endian" set in the device tree.
check "Documentation/devicetree/bindings/net/can/fsl-flexcan.txt" for
usage.
This is the standard practice followed in linux. for more info check:
Documentation/devicetree/bindings/common-properties.txt
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Sakar Arora <Sakar.Arora@freescale.com>
Reviewed-by: Zhengxiong Jin <Jason.Jin@freescale.com>
Reviewed-by: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Make c_can_pci_data structures const as they are only used during
a copy operation.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add a jump target so that a bit of exception handling can be better reused
at the end of this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This changes the calculation of the timestamps to use ktime_t
instead of struct timeval as the base. This gets rid of one
of the few remaining users of the deprecated ktime_to_timeval()
and timeval_to_ktime() helpers.
The code should also get more efficient, as we have now removed
all of the divisions.
I have left the cut-off for resetting the counters as 4.200
seconds, in order to leave the behavior unchanged otherwise.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
We want to remove 'struct timeval' and related interfaces since this is
generally not safe for use beyond 2038.
For peak_usb, we can simplify the internal interface by using ktime_t
directly. This should not change any behavior, but it avoids a few
conversions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
load_bpf_file() should fail if ioctl with command
PERF_EVENT_IOC_ENABLE and PERF_EVENT_IOC_SET_BPF fails.
When they do fail, proper error messages are printed.
With this change, the below "syscall_tp" run shows that
the maximum number of bpf progs attaching to the same
perf tracepoint is indeed enforced.
$ ./syscall_tp -i 64
prog #0: map ids 4 5
...
prog #63: map ids 382 383
$ ./syscall_tp -i 65
prog #0: map ids 4 5
...
prog #64: map ids 388 389
ioctl PERF_EVENT_IOC_SET_BPF failed err Argument list too long
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
cgropu+bpf prog array has a maximum number of 64 programs.
Let us apply the same limit here.
Fixes: e87c6bc3852b ("bpf: permit multiple bpf attachments for a single perf event")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor
Pull apparmor bugfix from John Johansen:
"Fix oops in audit_signal_cb hook marked for stable"
* tag 'apparmor-pr-2017-11-30' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor:
apparmor: fix oops in audit_signal_cb hook
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix a regression related to the ACPI EC handling during system
suspend/resume on some platforms and prevent modalias from being
exposed to user space for ACPI device object with "not functional and
not present" status.
Specifics:
- Fix an ACPI EC driver regression (from the 4.9 cycle) causing the
driver's power management operations to be omitted during system
suspend/resume on platforms where the EC instance from the ECDT
table is used instead of the one from the DSDT (Lv Zheng).
- Prevent modalias from being exposed to user space for ACPI device
objects with _STA returning 0 (not present and not functional) to
prevent driver modules from being loaded automatically for hardware
that is not actually present on some platforms (Hans de Goede)"
* tag 'acpi-4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / EC: Fix regression related to PM ops support in ECDT device
ACPI / bus: Leave modalias empty for devices which are not present
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
- add missing module information to the Mediatek cpufreq driver module
(Jesse Chan)
- fix config dependencies for the Loongson cpufreq driver (James Hogan)
- fix two issues related to CPU offline in the cpupower utility
(Abhishek Goel).
* tag 'pm-4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: mediatek: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
cpufreq: Add Loongson machine dependencies
cpupower : Fix cpupower working when cpu0 is offline
cpupowerutils: bench - Fix cpu online check
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull quota & reiserfs changes from Jan Kara:
- two error checking improvements for quota
- remove bogus i_version increase for reiserfs
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
quota: Check for register_shrinker() failure.
quota: propagate error from __dquot_initialize
reiserfs: remove unneeded i_version bump
|
|
into drm-fixes
Fixes for 4.15. Highlights:
- DC fixes for S3, gamma, audio, pageflipping, etc.
- fix a regression in radeon from kfd removal
- fix a ttm regression with swiotlb disabled
- misc other fixes
* 'drm-fixes-4.15' of git://people.freedesktop.org/~agd5f/linux: (36 commits)
drm/radeon: remove init of CIK VMIDs 8-16 for amdkfd
drm/ttm: fix populate_and_map() functions once more
drm/amd/display: USB-C / thunderbolt dock specific workaround
drm/amd/display: Switch to drm_atomic_helper_wait_for_flip_done
drm/amd/display: fix gamma setting
drm/amd/display: Do not put drm_atomic_state on resume
drm/amd/display: Fix couple more inconsistent NULL checks in dc_resource
drm/amd/display: Fix potential NULL and mem leak in create_links
drm/amd/display: Fix hubp check in set_cursor_position
drm/amd/display: Fix use before NULL check in validate_timing
drm/amd/display: Bunch of smatch error and warning fixes in DC
drm/amd/display: Fix amdgpu_dm bugs found by smatch
drm/amd/display: try to find matching audio inst for enc inst first
drm/amd/display: fix seq issue: turn on clock before programming afmt.
drm/amd/display: fix memory leaks on error exit return
drm/amd/display: check plane state before validating fbc
drm/amd/display: Do DC mode-change check when adding CRTCs
drm/amd/display: Revert noisy assert messages
drm/amd/display: fix split viewport rounding error
drm/amd/display: Check aux channel before MST resume
...
|
|
drm-fixes
mali-dp interface cleanups.
* 'for-upstream/mali-dp' of git://linux-arm.org/linux-ld:
drm: mali-dp: Disable planes when their CRTC gets disabled.
drm: mali-dp: Separate static internal data into a read-only structure.
drm/arm: Replace instances of drm_dev_unref with drm_dev_put.
drm: mali-dp: switch to drm_*_get(), drm_*_put() helpers
|
|
git://people.freedesktop.org/~gabbayo/linux into drm-fixes
This is amdkfd pull request for -rc2. It contains three small fixes to the
CIK SDMA code, compilation error fix in kfd_ioctl.h and fix to accessing
a pointer after it was released.
* tag 'drm-amdkfd-fixes-2017-11-26' of git://people.freedesktop.org/~gabbayo/linux:
uapi: fix linux/kfd_ioctl.h userspace compilation errors
drm/amdkfd: fix amdkfd use-after-free GP fault
drm/amdkfd: Fix SDMA oversubsription handling
drm/amdkfd: Fix SDMA ring buffer size calculation
drm/amdgpu: Fix SDMA load/unload sequence on HWS disabled mode
|
|
3 hdlcd fixes/cleanups
* 'for-upstream/hdlcd' of git://linux-arm.org/linux-ld:
drm/arm: Replace instances of drm_dev_unref with drm_dev_put.
drm: Fix checkpatch issue: "WARNING: braces {} are not necessary for single statement blocks."
drm: hdlcd: Update PM code to save/restore console.
|
|
git://git.pengutronix.de/git/pza/linux into drm-fixes
drm/imx: fix commit_tail for new drm_atomic_helper_setup_commit
Since commit 080de2e5be2d ("drm/atomic: Check for busy planes/connectors before
setting the commit"), drm_atomic_helper_setup_commit expects that blocking
commits have completed flipping before the commit_tail returns. Add the missing
wait_for_flip_done to commit_tail to ensure this.
* tag 'imx-drm-fixes-2017-11-30' of git://git.pengutronix.de/git/pza/linux:
drm/imx: always call wait_for_flip_done in commit_tail
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Disable transparent huge pages for now until we have a W/A
- Building fix when CONFIG_BACKLIGHT_CLASS_DEVICE is not selected
- GMBUS communication robustness
- Fbdev hotplug handling fix
gvt-fixes-2017-11-28
- regression fix for sane request alloc (Fred)
- locking fix (Changbin)
- fix invalid addr mask (Xiong)
- compression regression fix (Weinan)
- fix default pipe enable for virtual display (Xiaolin)
* tag 'drm-intel-fixes-2017-11-30' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915: Disable THP until we have a GPU read BW W/A
drm/i915/gvt: Correct ADDR_4K/2M/1G_MASK definition
drm/i915/gvt: enabled pipe A default on creating vgpu
drm/i915/gvt: Move request alloc to dispatch_workload path only
drm/i915/gvt: remove skl_misc_ctl_write handler
drm/i915/gvt: Fix unsafe locking caused by spin_unlock_bh
drm/i915: fix intel_backlight_device_register declaration
drm/i915/fbdev: Serialise early hotplug events with async fbdev config
drm/i915: Prevent zero length "index" write
drm/i915: Don't try indexed reads to alternate slave addresses
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux into drm-fixes
omapdrm fixes for 4.15
* Fix platform detection issue causing OMAP3 DPI output to have missing color bits
* Fix platform detection issue causing OMAP4 HDMI audio not to work
* tag 'omapdrm-4.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
omapdrm: hdmi4_cec: signedness bug in hdmi4_cec_init()
drm: omapdrm: Fix DPI on platforms using the DSI VDDS
omapdrm: hdmi4: Correct the SoC revision matching
drm/omap: displays: panel-dpi: add backlight dependency
drm/omap: Fix error handling path in 'omap_dmm_probe()'
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for -rc2
- big pile of bridge driver (mostly tc358767), all handled by Archit
and Andrez
- rockchip dsi fix
- atomic helper regression fix for spurious -EBUSY (Maarten)
- fix deferred fbdev fallout (Maarten)
* tag 'drm-misc-fixes-2017-11-30' of git://anongit.freedesktop.org/drm/drm-misc:
drm/bridge: tc358767: fix 1-lane behavior
drm/bridge: tc358767: fix AUXDATAn registers access
drm/bridge: tc358767: fix timing calculations
drm/bridge: tc358767: fix DP0_MISC register set
drm/bridge: tc358767: filter out too high modes
drm/bridge: tc358767: do no fail on hi-res displays
drm/bridge: Fix lvds-encoder since the panel_bridge rework.
drm/bridge: synopsys/dw-hdmi: Enable cec clock
drm/bridge: adv7511/33: Fix adv7511_cec_init() failure handling
drm/fb_helper: Disable all crtc's when initial setup fails.
drm/atomic: make drm_atomic_helper_wait_for_vblanks more agressive
drm/rockchip: dw-mipi-dsi: fix possible un-balanced runtime PM enable
|
|
With a nxp,se97 chip on an atmel sama5d31 board, the I2C adapter driver
is not always capable of avoiding the 25-35 ms timeout as specified by
the SMBUS protocol. This may cause silent corruption of the last bit of
any transfer, e.g. a one is read instead of a zero if the sensor chip
times out. This also affects the eeprom half of the nxp-se97 chip, where
this silent corruption was originally noticed. Other I2C adapters probably
suffer similar issues, e.g. bit-banging comes to mind as risky...
The SMBUS register in the nxp chip is not a standard Jedec register, but
it is not special to the nxp chips either, at least the atmel chips
have the same mechanism. Therefore, do not special case this on the
manufacturer, it is opt-in via the device property anyway.
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
We used to have some cmpxchg syscalls. They're no longer there, so we
no longer need the include.
CC: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
Despite RISC-V having a direct 'fence.i' instruction available to
userspace (which we can't trap!), that's not actually viable when
running on Linux because the kernel might schedule a process on another
hart. There is no way for userspace to handle this without invoking the
kernel (as it doesn't know the thread->hart mappings), so we've defined
a RISC-V specific system call to flush the instruction cache.
This patch adds both a system call and a VDSO entry. If possible, we'd
like to avoid having the system call be considered part of the
user-facing ABI and instead restrict that to the VDSO entry -- both just
in general to avoid having additional user-visible ABI to maintain, and
because we'd prefer that users just call the VDSO entry because there
might be a better way to do this in the future (ie, one that doesn't
require entering the kernel).
Signed-off-by: Andrew Waterman <andrew@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
The RISC-V ISA allows for instruction caches that are not coherent WRT
stores, even on a single hart. As a result, we need to explicitly flush
the instruction cache whenever marking a dirty page as executable in
order to preserve the correct system behavior.
Local instruction caches aren't that scary (our implementations actually
flush the cache, but RISC-V is defined to allow higher-performance
implementations to exist), but RISC-V defines no way to perform an
instruction cache shootdown. When explicitly asked to do so we can
shoot down remote instruction caches via an IPI, but this is a bit on
the slow side.
Instead of requiring an IPI to all harts whenever marking a page as
executable, we simply flush the currently running harts. In order to
maintain correct behavior, we additionally mark every other hart as
needing a deferred instruction cache which will be taken before anything
runs on it.
Signed-off-by: Andrew Waterman <andrew@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
When configuring an IPv6 address mask, we should use SLICE_NUM_MASK as
the mask in order to make sure all bits are masked by the hardware.
Also, we want matching entries to have a CHAIN_ID value set to the same
value as the rule index we return to user-space for convenience, so fix
that too.
Fixes: ba0696c22e7c ("net: dsa: bcm_sf2: Add support for IPv6 CFP rules")
Fixes: dd8eff68343d ("net: dsa: bcm_sf2: Allow matching arbitrary IPv6 masks/lengths")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rafal Ozieblo says:
====================
Receive packets filtering for macb driver
This patch series adds support for receive packets
filtering for Cadence GEM driver. Packets can be redirect
to different hardware queues based on source IP, destination IP,
source port or destination port. To enable filtering,
support for RX queueing was added as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch allows filtering received packets to different
hardware queues (aka ntuple).
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added statistics per queue:
- qX_rx_packets
- qX_rx_bytes
- qX_rx_dropped
- qX_tx_packets
- qX_tx_bytes
- qX_tx_dropped
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To be able for packet reception on different RX queues some
configuration has to be performed. This patch checks how many
hardware queue does GEM support and initializes them.
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are several reasons for increasing the receive ring sizes:
1. The original ring size of 256 was chosen about 10 years ago when
vmxnet3 was first created. At that time, 10Gbps Ethernet was not prevalent
and servers were dominated by 1Gbps Ethernet. Now 10Gbps is common place,
and higher bandwidth links -- 25Gbps, 40Gbps, 50Gbps -- are starting
to appear. 256 Rx ring entries are simply not enough to keep up with
higher link speed when there is a burst of network frames coming from
these high speed links. Even with full MTU size frames, they are gone
in a short time. It is also more common to have a mix of frame sizes,
and more likely bi-modal distribution of frame sizes so the average frame
size is not close to full MTU. If we consider average frame size of 800B,
1024 frames that come in a burst takes ~0.65 ms to arrive at 10Gbps. With
256 entires, it takes ~0.16 ms to arrive at 10Gbps. At 25Gbps or 40Gbps,
this time is reduced accordingly.
2. On a hypervisor where there are many VMs and CPU is over committed,
i.e. the number of VCPUs is more than the number of VCPUs, each PCPU is
in effect time shared between multiple VMs/VCPUs. The time granularity at
which this multiplexing occurs is typically coarser than between processes
on a guest OS. Trying to time slice more finely is not efficient, for
example, if memory cache is barely warmed up when switching from one VM
to another occurs. This CPU overcommit adds delay to when the driver
in a VM can service incoming packets. Whether CPU is over committed
really depends on customer workloads. For certain situations, it is very
common. For example, workloads of desktop VMs and product testing setups.
Consolidation and sharing is what drives efficiency of a customer setup
for such workloads. In these situations, the raw network bandwidth may
not be very high, but the delays between when a VM is running or not
running can also be relatively long.
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Acked-by: Jin Heo <heoj@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Acked-by: Boon Ang <bang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Attach flag 1 == BPF_F_ALLOW_OVERRIDE; attach flag 2 == BPF_F_ALLOW_MULTI.
Update the calls to bpf_prog_attach() in test_cgrp2_attach2.c to use the
names over the magic numbers.
Fixes: 39323e788cb67 ("samples/bpf: add multi-prog cgroup test case")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The default rlimit RLIMIT_MEMLOCK is 64KB. In certain cases,
e.g. in a test machine mimicking our production system, this test may
fail due to unable to charge the required memory for prog load:
# ./test_verifier_log
Test log_level 0...
ERROR: Program load returned: ret:-1/errno:1, expected ret:-1/errno:22
Changing the default rlimit RLIMIT_MEMLOCK to unlimited makes
the test always pass.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Fixes:
include/asm-generic/mm_hooks.h:20:11: warning: 'struct vm_area_struct' declared inside parameter list will not be visible outside of this definition or declaration
include/asm-generic/mm_hooks.h:19:38: warning: 'struct mm_struct' declared inside parameter list will not be visible outside of this definition or declaration
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
Fixes the following on allmodconfig build:
profile.c:(.text+0x3e4): undefined reference to `setup_profiling_timer'
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
These are the ones needed by current allmodconfig, so add them instead
of everything other architectures are exporting -- the rest can be
added on demand later if needed.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
Needed by some modules (exported by other architectures).
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
include <linux/types.h> for __iomem definition. Also, add volatile to
iounmap() like other architectures have it to avoid "discarding
volatile" warnings from some drivers.
Finally, explicitly promote the base address for INB/OUTB functions to
avoid some old legacy drivers complaining about int-to-ptr promotions.
The drivers are unlikely to work but they're included in allmodconfig
so the warnings are noisy.
Fixes, among other warnings, these with allmodconfig:
../arch/riscv/include/asm/io.h:24:21: error: expected '=', ',', ';', 'asm' or '__attribute__' before '*' token
extern void __iomem *ioremap(phys_addr_t offset, unsigned long size);
sound/pci/echoaudio/echoaudio.c: In function 'snd_echo_free':
sound/pci/echoaudio/echoaudio.c:1879:10: warning: passing argument 1 of 'iounmap' discards 'volatile' qualifier from pointer target type [-Wdiscarded-qualifiers]
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
INT and SHORT are used by some drivers that pull in the include files,
so prefixing helps avoid namespace conflicts. Other constructs in the
same file already uses this.
Fixes, among others, these warnings with allmodconfig:
../sound/core/pcm_misc.c:43:0: warning: "INT" redefined
#define INT __force int
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
Fixes this from allmodconfig:
drivers/tty/serial/earlycon.c:27:10: fatal error: asm/serial.h: No such file or directory
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
Utilize the much more capable b53_get_tag_protocol() which takes care of
all Broadcom switches specifics to resolve which port can have Broadcom
tags enabled or not.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
Once the inode item writeback errors is already fixed, it's time to fix the same
problem in dquot code.
Although there were no reports of users hitting this bug in dquot code (at least
none I've seen), the bug is there and I was already planning to fix it when the
correct approach to fix the inodes part was decided.
This patch aims to fix the same problem in dquot code, regarding failed buffers
being unable to be resubmitted once they are flush locked.
Tested with the recently test-case sent to fstests list by Hou Tao.
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
Since we've used up all the bits in i_mode, the existing mode check
doesn't actually do anything useful. However, we've not used all the
bit values in the format portion of i_mode, so we /do/ need to test
that for bad values.
Fixes: 80e4e1268 ("xfs: scrub inodes")
Fixes-coverity-id: 1423992
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
|
|
The first thing that xfs_writepage_map does is clobber the offset
parameter. Since we never use the passed-in value, turn the parameter
into a local variable. This gets rid of an UBSAN warning in generic/466.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
|
