| Age | Commit message (Collapse) | Author |
|---|
|
Enable all three in the driver. Early documentation
indicated the 3rd one was used for something else, but
that is not the case.
v2: handle disable as well
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
When a key is being garbage collected, it's key->user would get put before
the ->destroy() callback is called, where the key is removed from it's
respective tracking structures.
This leaves a key hanging in a semi-invalid state which leaves a window open
for a different task to try an access key->user. An example is
find_keyring_by_name() which would dereference key->user for a key that is
in the process of being garbage collected (where key->user was freed but
->destroy() wasn't called yet - so it's still present in the linked list).
This would cause either a panic, or corrupt memory.
Fixes CVE-2014-9529.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
This patch fixes a bug where deallocate_vmid() didn't actually unmap the
VMID<-->PASID mapping (in the registers).
That can cause undefined behavior.
This bug only occurs in non-HWS mode.
Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch introduces an independent cpuidle driver for
i.MX6SX, and supports arm power off in idle, totally
3 levels of cpuidle are supported as below:
1. ARM WFI;
2. SOC in WAIT mode;
3. SOC in WAIT mode + ARM power off.
ARM power off can save at least 5mW power.
This patch also replaces imx6q_enable_rbc with imx6_enable_rbc.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Now we support DSM in OCRAM for all i.MX6 SoCs,
the resume entry point is set in asm code of
suspend-imx6.S, so no need to set the resume
entry point for SRC in pre-suspend flow.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add basic i.MX6SoloX Sabre Auto board support, currently
only debug UART and uSDHC are supported on this board.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
imx6sx-sdb has two s25fl128s quad spi flash. Add support for them.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
According to Documentation/devicetree/bindings/media/coda.txt:
- clock-names : Should be "ahb", "per"
The OCRAM clock is already provided inside the ocram node, so remove the OCRAM
clock from the VPU node.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
For those clk gates which hold share count, since its is_enabled
callback is only checking the share count rather than reading
the hardware register setting, in the late phase of kernel bootup,
the clk_disable_unused action will NOT handle the scenario of
share_count is 0 but the hardware setting is enabled, actually,
U-Boot normally enables all clk gates, then those shared clk gates
will be always enabled until they are used by some modules.
So the problem would be: when kernel boot up, the usecount cat
from clk tree is 0, but the clk gates actually is enabled in
hardware register, it will confuse user and bring unnecessary power
consumption.
This patch adds .disable_unused callback and using hardware register
check for .is_enabled callback of shared nodes to handle such scenario
in late phase of kernel boot up, then the hardware status will match the
clk tree info.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add shift capabilties for the frequency multiplier (DIV_SELECT) to
support Vybrid's USB PLL oddity. The PLL3 and PLL7 are the only
PLL control registers which have the DIV_SELECT bit shifted by
one. Be aware, there are known documentation errors in the
reference manual too.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The Vybrid SoC family (in the kernel known as vf610) is a familiy
of multiple similar SoC's. The VF5xx series comes without secondary
Cortex-M4 core, while the second number VFx1x indicates the presence
of a L2 cache controller.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The i.MX53 has a SAHARA v4 core. Add it to the dtsi.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Currently the cpufreq volt/freq table we used is
for LDO enable mode, according to latest datasheet
Rev. 3, 03/2014, the volt/freq table is as below:
LDO enabled(min value):
996MHz: VDDARM: 1.225V, VDDSOC: 1.150V;
792MHz: VDDARM: 1.150V, VDDSOC: 1.150V;
396MHz: VDDARM: 1.050V, VDDSOC: 1.150V;
LDO bypassed(min value):
996MHz: VDDARM: 1.250V, VDDSOC: 1.150V;
792MHz: VDDARM: 1.150V, VDDSOC: 1.150V;
396MHz: VDDARM: 1.050V, VDDSOC: 1.150V;
Adding 25mV to cover board IR drop, for LDO enabled
mode of 996MHz, VDDARM should be 1.250V, so this
patch updates it.
Signed-off-by: Anson Huang <b20788@freescale.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
According to latest i.MX6Q datasheet Rev. 3, 02/2014,
the latest cpufreq volt/freq table is as below:
LDO enabled/bypassed(min value):
996MHz: VDDARM: 1.225V, VDDSOC: 1.150V;
792MHz: VDDARM: 1.150V, VDDSOC: 1.150V;
396MHz: VDDARM: 0.925V, VDDSOC: 1.150V;
the 792MHz setpoint's VDDARM min voltage is updated
from 1.125V to 1.150V, adding 25mV to cover board IR
drop, 1.175V is the right voltage we should use.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add the system reset controller (SRC) module and use syscon-reboot
to register a restart handler which restarts the SoC using the
SRC SW_RST bit.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Update the VPU compatible strings to also use "cnm,coda<model>".
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
On the Colibri module, the RMII clock for the Ethernet PHY is
generated by the SoC. This patch adds that missing pin to the
pinctrl of FEC1. Because the boot loader initializes this pin,
ethernet worked even without this pin so far.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
During restructuring of the device tree files the watchdog was
changed to be disabled by default. However, since the watchdog
instance is dedicated to the Cortex-A5, enable the peripheral
by default in the base device tree vf500.dtsi.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
stac_store_hints() does utterly wrong for masking the values for
gpio_dir and gpio_data, likely due to copy&paste errors. Fortunately,
this feature is used very rarely, so the impact must be really small.
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This code only runs when action == BUS_NOTIFY_REMOVED_DEVICE,
so it can't be BUS_NOTIFY_DEL_DEVICE.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Since commit 1196c2f a domain is only destroyed in the
notifier path if it is hot-unplugged. This caused a
domain leakage in iommu_attach_device when a driver was
unbound from the device and bound to VFIO. In this case the
device is attached to a new domain and unlinked from the old
domain. At this point nothing points to the old domain
anymore and its memory is leaked.
Fix this by explicitly freeing the old domain in
iommu_attach_domain.
Fixes: 1196c2f (iommu/vt-d: Fix dmar_domain leak in iommu_attach_device)
Cc: stable@vger.kernel.org # v3.18
Tested-by: Jerry Hoemann <jerry.hoemann@hp.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Commit a720b41c41f5a7e4 ("iommu/arm-smmu: change IOMMU_EXEC to
IOMMU_NOEXEC") has inverted and replaced the IOMMU_EXEC flag with
IOMMU_NOEXEC. Update the driver accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This patch fixes this allyesconfig target build error with older
binutils.
LD arch/x86/crypto/built-in.o
ld: arch/x86/crypto/sha-mb/built-in.o: No such file: No such file or directory
Cc: stable@vger.kernel.org # 3.18+
Signed-off-by: Vinson Lee <vlee@twitter.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The "by8" counter mode optimization is broken for 128 bit keys with
input data longer than 128 bytes. It uses the wrong key material for
en- and decryption.
The key registers xkey0, xkey4, xkey8 and xkey12 need to be preserved
in case we're handling more than 128 bytes of input data -- they won't
get reloaded after the initial load. They must therefore be (a) loaded
on the first iteration and (b) be preserved for the latter ones. The
implementation for 128 bit keys does not comply with (a) nor (b).
Fix this by bringing the implementation back to its original source
and correctly load the key registers and preserve their values by
*not* re-using the registers for other purposes.
Kudos to James for reporting the issue and providing a test case
showing the discrepancies.
Reported-by: James Yonan <james@openvpn.net>
Cc: Chandramouli Narayanan <mouli@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.18
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This reverts commit ca34e3b5c808385b175650605faa29e71e91991b.
It turns out that the p54 and cw2100 drivers assume that there's
tailroom even when they don't say they really need it. However,
there's currently no way for them to explicitly say they do need
it, so for now revert this.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=90331.
Cc: stable@vger.kernel.org
Fixes: ca34e3b5c808 ("mac80211: Fix accounting of the tailroom-needed counter")
Reported-by: Christopher Chavez <chrischavez@gmx.us>
Bisected-by: Larry Finger <Larry.Finger@lwfinger.net>
Debugged-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Commit 897c329bc ("ALSA: usb: caiaq: check for cdev->n_streams > 1")
introduced a safety check to protect against bogus data provided by
devices. However, the n_streams variable is already divided by
CHANNELS_PER_STREAM, so the correct check is 'n_streams > 0'.
Fix this to un-break support for stereo devices.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Cc: stable@kernel.org [v3.18+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The CPSW IP implements pulse-signaled interrupts. Due to
that we must write a correct, pre-defined value to the
CPDMA_MACEOIVECTOR register so the controller generates
a pulse on the correct IRQ line to signal the End Of
Interrupt.
The way the driver is written today, all four IRQ lines
are requested using the same IRQ handler and, because of
that, we could fall into situations where a TX IRQ fires
but we tell the controller that we ended an RX IRQ (or
vice-versa). This situation triggers an IRQ storm on the
reserved IRQ 127 of INTC which will in turn call ack_bad_irq()
which will, then, print a ton of:
unexpected IRQ trap at vector 00
In order to fix the problem, we are moving all calls to
cpdma_ctlr_eoi() inside the IRQ handler and making sure
we *always* write the correct value to the CPDMA_MACEOIVECTOR
register. Note that the algorithm assumes that IRQ numbers and
value-to-be-written-to-EOI are proportional, meaning that a
write of value 0 would trigger an EOI pulse for the RX_THRESHOLD
Interrupt and that's the IRQ number sitting in the 0-th index
of our irqs_table array.
This, however, is safe at least for current implementations of
CPSW so we will refrain from making the check smarter (and, as
a side-effect, slower) until we actually have a platform where
IRQ lines are swapped.
This patch has been tested for several days with AM335x- and
AM437x-based platforms. AM57x was left out because there are
still pending patches to enable ethernet in mainline for that
platform. A read of the TRM confirms the statement on previous
paragraph.
Reported-by: Yegor Yefremov <yegorslists@googlemail.com>
Fixes: 510a1e7 (drivers: net: davinci_cpdma: acknowledge interrupt properly)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull UML fixes from Richard Weinberger:
"Two fixes for UML regressions. Nothing exciting"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
x86, um: actually mark system call tables readonly
um: Skip futex_atomic_cmpxchg_inatomic() test
|
|
Commit 9fc2105aeaaf ("ARM: 7830/1: delay: don't bother reporting
bogomips in /proc/cpuinfo") breaks audio in python, and probably
elsewhere, with message
FATAL: cannot locate cpu MHz in /proc/cpuinfo
I'm not the first one to hit it, see for example
https://theredblacktree.wordpress.com/2014/08/10/fatal-cannot-locate-cpu-mhz-in-proccpuinfo/
https://devtalk.nvidia.com/default/topic/765800/workaround-for-fatal-cannot-locate-cpu-mhz-in-proc-cpuinf/?offset=1
Reading original changelog, I have to say "Stop breaking working setups.
You know who you are!".
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit a074335a370e ("x86, um: Mark system call tables readonly") was
supposed to mark the sys_call_table in UML as RO by adding the const,
but it doesn't have the desired effect as it's nevertheless being placed
into the data section since __cacheline_aligned enforces sys_call_table
being placed into .data..cacheline_aligned instead. We need to use
the ____cacheline_aligned version instead to fix this issue.
Before:
$ nm -v arch/x86/um/sys_call_table_64.o | grep -1 "sys_call_table"
U sys_writev
0000000000000000 D sys_call_table
0000000000000000 D syscall_table_size
After:
$ nm -v arch/x86/um/sys_call_table_64.o | grep -1 "sys_call_table"
U sys_writev
0000000000000000 R sys_call_table
0000000000000000 D syscall_table_size
Fixes: a074335a370e ("x86, um: Mark system call tables readonly")
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
futex_atomic_cmpxchg_inatomic() does not work on UML because
it triggers a copy_from_user() in kernel context.
On UML copy_from_user() can only be used if the kernel was called
by a real user space process such that UML can use ptrace()
to fetch the value.
Reported-by: Miklos Szeredi <miklos@szeredi.hu>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Tested-by: Daniel Walter <d.walter@0x90.at>
|
|
git://people.freedesktop.org/~gabbayo/linux into linus
Highlights:
- Link order changes in drm/Makefile and drivers/Makefile to fix issue
when amdkfd, radeon and amd_iommu_v2 are compiled inside the kernel
image.
- Consider kernel configuration (using #IFDEFs) when radeon initializes
amdkfd, due to a specific configuration that makes symbol_request()
return a non-NULL value when a symbol doesn't exists. Rusty Russel
is helping me to find the root cause, but it may take a while because
of year-end so I'm sending this as a band-aid solution.
* tag 'amdkfd-fixes-2014-12-30' of git://people.freedesktop.org/~gabbayo/linux:
drm/radeon: Init amdkfd only if it was compiled
amdkfd: actually allocate longs for the pasid bitmask
drm: Put amdkfd before radeon in drm Makefile
drivers: Move iommu/ before gpu/ in Makefile
amdkfd: Remove duplicate include
amdkfd: Fixing topology bug in building sysfs nodes
amdkfd: Fix accounting of device queues
|
|
git://anongit.freedesktop.org/drm-intel into linus
I've had these since before -rc1, but they missed my last pull
request. Real bug fixes and mostly cc: stable material.
* tag 'drm-intel-next-fixes-2014-12-30' of git://anongit.freedesktop.org/drm-intel:
drm/i915: add missing rpm ref to i915_gem_pwrite_ioctl
Revert "drm/i915: Preserve VGACNTR bits from the BIOS"
drm/i915: Don't call intel_prepare_page_flip() multiple times on gen2-4
drm/i915: Kill check_power_well() calls
|
|
The currently perf diff didn't add the baseline and delta (or other
compute) fields to the sort list so output will be sorted by other
fields like alphabetical order of DSO or symbol as below example.
Fix it by adding hpp formats for the fields and provides default compare
functions.
Before:
$ perf diff
# Event 'cycles'
#
# Baseline Delta Shared Object Symbol
# ........ ....... .................. ...............................
#
[bridge] [k] ip_sabotage_in
[btrfs] [k] __etree_search.constprop.47
0.01% [btrfs] [k] btrfs_file_mmap
0.01% -0.01% [btrfs] [k] btrfs_getattr
[e1000e] [k] e1000_watchdog
0.00% [kernel.vmlinux] [k] PageHuge
0.00% [kernel.vmlinux] [k] __acct_update_integrals
0.00% [kernel.vmlinux] [k] __activate_page
[kernel.vmlinux] [k] __alloc_fd
0.02% +0.02% [kernel.vmlinux] [k] __alloc_pages_nodemask
...
After:
# Baseline Delta Shared Object Symbol
# ........ ....... .................. ................................
#
24.73% -4.62% perf [.] append_chain_children
7.96% -1.29% perf [.] dso__find_symbol
6.97% -2.07% libc-2.20.so [.] vfprintf
4.61% +0.88% libc-2.20.so [.] __fprintf_chk
4.41% +2.43% perf [.] sort__comm_cmp
4.10% -0.16% perf [.] comm__str
4.03% -0.93% perf [.] machine__findnew_thread_time
3.82% +3.09% perf [.] __hists__add_entry
2.95% -0.18% perf [.] sort__dso_cmp
...
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1419656793-32756-1-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Currently, 'perf list --raw-dump' requires extra arguments
(e.g., hw) to invoke, which breaks bash/zsh completion
(perf-completion.sh).
$ perf list --raw-dump
Error: unknown option `raw-dump'
usage: perf list [hw|sw|cache|tracepoint|pmu|event_glob]
After,
$ perf list --raw-dump
cpu-cycles instructions cache-references cache-misses ...
Signed-off-by: Taesoo Kim <tsgatesv@gmail.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Taesoo kim <taesoo@gatech.edu>
Link: http://lkml.kernel.org/r/1419997015-11071-1-git-send-email-tsgatesv@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
When allocation of all RQs fail, we do not free previously allocated buffers,
before returning error. This causes memory leak.
This patch fixes this by calling vnic_rq_clean(), which frees all the rq
buffers.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some buggy firmwares export an incorrect MAC address (00:a0:c6:00:00:00). This
makes for example checking devices for random MAC addresses tricky, and you
might end up with multiple network interfaces with the same address.
This patch tries to fix, or at least improve, the situation by setting the MAC
address of devices with this firmware bug to a random address. I tested the
patch with two devices that has this firmware bug (Huawei E398 and E392), and
network traffic worked fine after changing the address.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of three fixes: one to correct an abort path thinko
causing failures (and a panic) in USB on device misbehaviour, One to
fix an out of order issue in the fnic driver and one to match discard
expectations to qemu which otherwise cause Linux to behave badly as a
guest"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
SCSI: fix regression in scsi_send_eh_cmnd()
fnic: IOMMU Fault occurs when IO and abort IO is out of order
sd: tweak discard heuristics to work around QEMU SCSI issue
|
|
Until now, when VLAN acceleration was in use, the bytes of the VLAN header
were not included in port or flow byte counters. They were however
included when VLAN acceleration was not used. This commit corrects the
inconsistency, by always including the VLAN header in byte counters.
Previous discussion at
http://openvswitch.org/pipermail/dev/2014-December/049521.html
Reported-by: Motonori Shindo <mshindo@vmware.com>
Signed-off-by: Ben Pfaff <blp@nicira.com>
Reviewed-by: Flavio Leitner <fbl@sysclose.org>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Thomas Jarosch reported IPsec TCP stalls when a PMTU event occurs.
In fact the problem was completely unrelated to IPsec. The bug is
also reproducible if you just disable TSO/GSO.
The problem is that when the MSS goes down, existing queued packet
on the TX queue that have not been transmitted yet all look like
TSO packets and get treated as such.
This then triggers a bug where tcp_mss_split_point tells us to
generate a zero-sized packet on the TX queue. Once that happens
we're screwed because the zero-sized packet can never be removed
by ACKs.
Fixes: 1485348d242 ("tcp: Apply device TSO segment limit earlier")
Reported-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cheers,
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Nothing too exciting as a new year's start here: most of fixes are for
ASoC, a boot crash fix on OMAP for deferred probe, a few driver
specific fixes (Intel, dwc, rockchip, rt5677), in addition to typo
fixes in kerneldoc comments for PCM"
* tag 'sound-3.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: pcm: Fix kerneldoc for params_*() functions
ASoC: rockchip: i2s: fix maxburst of dma data to 4
ASoC: rockchip: i2s: fix error defination of transmit data level
ASoC: Intel: correct the fixed free block allocation
ASoC: rt5677: fixed rt5677_dsp_vad_put rt5677_dsp_vad_get panic
ASoC: Intel: Fix BYTCR machine driver MODULE_ALIAS
ASoC: Intel: Fix BYTCR firmware name
ASoC: dwc: Iterate over all channels
ASoC: dwc: Ensure FIFOs are flushed to prevent channel swap
ASoC: Intel: Add I2C dependency to two new machines
ASoC: dapm: Remove snd_soc_of_parse_audio_routing() due to deferred probe
|
|
Altera network device doesn't come up after
ifconfig eth0 down
ifconfig eth0 up
The reason behind is clearing priv->phydev during tse_shutdown().
The phydev is not restored back at tse_open().
Resubmiting as to follow Tobias Klauser suggestion.
phy_start/phy_stop are called on each ifup/ifdown and
phy_disconnect is called once during the module removal.
Signed-off-by: Kostya Belezko <bkostya@hotmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Or Gerlitz says:
====================
mlx4 driver fixes for 3.19-rc2
Please push Maor's patch to -stable >= 3.17
Jack's fixes error-flow issues introduced in 3.19-rc1, no need for -stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We shouldn't call UNMAP_FA here, this is done in mlx4_load_one.
If mlx4_query_func fails, we need to invoke CLOSE_HCA for both
native and master.
Fixes: a0eacca948d2 ('net/mlx4_core: Refactor mlx4_load_one')
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
