| Age | Commit message (Collapse) | Author |
|---|
|
Use table based setup to register the controls and DAPM widgets and routes. This
on one hand makes the code a bit shorter and cleaner and on the other hand the
board level DAPM elements get registered in the card's DAPM context rather than
in the CODEC's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Use table based setup to register the controls and DAPM widgets and routes. This
on one hand makes the code a bit shorter and cleaner and on the other hand the
board level DAPM elements get registered in the card's DAPM context rather than
in the CODEC's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Use table based setup to register the controls and DAPM widgets and routes.
This on one hand makes the code a bit shorter and cleaner and on the other
hand the board level DAPM elements get registered in the card's DAPM context
rather than in the CODEC's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
In fsl_ssi_hw_params() we update the I2S and NET bits using the i2s_mode
variable. The fsl_ssi_set_dai_fmt() function only writes the i2s-mode to
the i2s_mode variable and not the NET bit. This fixes it by adding that
bit to i2s_mode.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
fsl_ssi_set_dai_fmt() manages most of the register setup routines now.
fsl_ssi_setup() makes the same as fsl_ssi_set_dai_fmt() but it relies on
DT properties.
In most cases the settings of fsl_ssi_setup() are already overwritten by
fsl_ssi_set_dai_fmt() when it is called by the soc-core when a sound
card is added. As these settings depend on the combination of codec and
cpu DAI, this should really be done by sound cards.
This patch removes fsl_ssi_setup() and adds the missing register setups
to fsl_ssi_set_dai_fmt(). It also removes all calls to fsl_ssi_setup().
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The SAI mainly has the following clocks:
bus clock
control and configure registers and to generate synchronous
interrupts and DMA requests.
mclk1, mclk2, mclk3
to generate the bit clock when the receiver or transmitter is
configured for an internally generated bit clock.
So this patch adds these clocks and their clock controls to the driver.
[ To concern the old DTB cases, I've added a bit of extra code to make
the driver compatible with them. And by marking clock NULL if failed
to get, the clk_prepare() or clk_get_rate() would easily return 0
so no further path should be broken. -- by Nicolin ]
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The next coming i.MX6 Solo X SoC also contains SAI module while we use
imp_pcm_init() for i.MX platform.
So this patch adds one compatible route for imx6sx and updates the DT
doc accordingly.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
We only enable one side interrupt for each stream since over/underrun
on the opposite stream would be resulted from what we previously did,
enabling TERE but remaining FRDE disabled, even though the xrun on the
opposite direction will not break the current stream.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The current trigger() has two crucial problems:
1) The DMA request enabling operations (FSL_SAI_CSR_FRDE) for Tx and Rx are
now totally exclusive: It would fail to run simultaneous Tx-Rx cases.
2) The TERE disabling operation depends on an incorrect condition -- active
reference count that only gets increased in snd_pcm_open() and decreased
in snd_pcm_close(): The TERE would never get cleared.
So this patch overwrites the trigger function by following these rules:
A) We continue to support tx-async-while-rx-sync-to-tx case alone, which's
originally limited by this fsl_sai driver, but we make the code easy to
modify for the further support of the opposite case.
B) We enable both TE and RE for PLAYBACK stream or CAPTURE stream but only
enabling the DMA request bit (FSL_SAI_CSR_FRDE) of the current direction
due to the requirement of SAI -- For tx-async-while-rx-sync-to-tx case,
the receiver is enabled only when both the transmitter and receiver are
enabled.
Tested cases:
a) aplay test.wav -d5
b) arecord -r44100 -c2 -fS16_LE test.wav -d5
c) arecord -r44100 -c2 -fS16_LE -d5 | aplay
d) (aplay test2.wav &); sleep 1; arecord -r44100 -c2 -fS16_LE test.wav -d1
e) (arecord -r44100 -c2 -fS16_LE test.wav -d5 &); sleep 1; aplay test.wav -d1
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch improves fsl_sai_isr() in these ways:
1, Add comment for mask fetching code.
2, Return IRQ_NONE if the IRQ is not for the device.
3, Use regmap_write() instead of regmap_update_bits().
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch allow to select individual common sound options and
as a result allow using sound cards/codecs based on DT description.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch provide separation of the main audio options and boards.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
To make the code look uniform.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Configuration for LEFT_J format.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The FS needs to be inverted in McASP compared to other supported formats.
Use a flag to indicate if the FS needs to be inverted.
At the same time fail when non supported format is asked since the default
case was anyways configuring McASP to a not valid format.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
FS polarity can be either rising or falling edge in McASP. Instead of
accessing the registers in every switch/case set a flag and write the
registers after the switch for the invert configuration.
This change will help when adding support for more formats also.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
DSP_A is like DSP_B mode but with one bit delay after the FS.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Use intermediate variable for the data delay needed for the specific format
and write the register after the format configuration at once.
This will help to control the number of lines as support for more formats
going to be added.
Also fixes a case when we switch between two formats with different delay
requirements.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
When the AFIFO is not enabled but more than one serializers are used the DMA
need to transfer number of words equal to active serializers when a DMA
request is generated.
When configuring the burst for the DMA avoid using value '1' for the burst
since it is going to enable additional logic in the DMA drivers. Burst '1'
means that the DMA should send/receive one word per DMA requests.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
(dynamic depth)
Configure the AFIFO numevt parameter based on the requested tx/rx_numevt,
active serializers and period size in words.
In this way McASP can adopt it's (and the DMA) configuration runtime and
can pick the most optimal setup which satisfy the parameters.
This way we do not need to place any constraint on the stream itself,
allowing application greater freedom on how they want to set up ALSA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Move the dma_params->fifo_level and dma_data->maxburst configuration to the
mcasp_common_hw_param() function where we configure the AFIFO registers.
It makes the code regarding to AFIFO and DMA configuration more easy to
follow since it is now clear how the AFIFO and how the DMA is going to be
configured.
Previously this has been done in two functions using a bit different
calculation form - which ended up with the same result in both case at the
end, but it was confusing.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
We can have more linear code flow by using variables in
mcasp_common_hw_param() related to the AFIFO configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
requred -> required
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Set up the playback_dma_data/capture_dma_data for the dai at probe
time since the generic dmaengine PCM stack needs to have access to
this information early.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
To save drivers using davinci-pcm and edma-pcm the need to fiddle with
!CONFIG_SND_DAVINCI_SOC in their code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Change reg's type from unsigned short to unsigned int. So that we can use
32 bits reg value in snd_soc_update_bits.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
There is an increasing amount of code that is very similar between platforms,
CODECS and other components. Making platforms a component will allow us to
share this code. For now the patch just adds component and component_driver
fields to the platform and platform_driver structs and registers the platform as
a component. Followup patches will be used to consolidate code between the
different types of components.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
snd_soc_register_component()
snd_soc_unregister_component() takes the parent device of the component as a
parameter and then looks up the component based on this. This is a problem if
multiple components are registered for the same parent device. Currently drivers
do not do this, but some drivers register a CPU DAI component and a platform for
the same parent device. This will become a problem once platforms are also made
components. To make sure that snd_soc_unregister_component() will not
accidentally unregister the platform in such a case only consider components
that were registered with snd_soc_register_component(). This is only meant as
short term stopgap solution to be able to continue componentisation. Long term
we'll need something different.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
There are no ASoC drivers left that use them and new drivers are supposed to use
regmap for this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
soc-core.c is getting quite crowded. Move all IO related functions that are
still in soc-core.c to soc-io.c
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
SOC_SINGLE_XR_SX controls currently only work with CODECs that set the
'reg_word_size' field in their snd_soc_codec_driver struct. Going forward
support for ASoC level IO will eventually be removed and all drivers will be
converted to regmap. Preparing for the transition this patch adds support for
CODECs using regmap for IO to the SOC_SINGLE_XR_SX control. We already have the
val_bytes field in the CODEC struct which holds the number of bytes per word,
but it is only initialized when regmap is used. Also initialize it for drivers
still using legacy IO and update the SOC_SINGLE_XR_SX handlers to use it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
For platform controls snd_kcontrol_chip() currently returns a pointer to the
platform that registered the control. With the upcoming consolidation of
platform and CODEC controls this will change. Prepare for this by introducing
the snd_soc_kcontrol_platform() helper function that will hide the
implementation details of how the platform for a control can be obtained. This
will allow us to change this easily in the future.
The patch also updates all platforms to use this new helper function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
For CODEC controls snd_kcontrol_chip() currently returns a pointer to the
CODEC that registered the control. With the upcoming consolidation of
platform and CODEC controls this will change. Prepare for this by introducing
the snd_soc_kcontrol_codec() helper function that will hide the implementation
details of how the CODEC for a control can be obtained. This will allow us to
change this easily in the future.
The patch also updates all CODEC drivers to use the new helper function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Some thing Likes:
reproduce: make C=1 CF=-D__CHECK_ENDIAN__
sparse warnings: (new ones prefixed by >>)
>> sound/soc/codecs/wm8997.c:1084:15: sparse: symbol \
'wm8997_get_regmap' was not declared. Should it be static?
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add the default regmap I/O setting to snd_soc_register_codec() while
the CODEC is initialising, which will be called by CODEC driver device
probe(), and then we can make XXX_set_cache_io() go away entirely from each
CODEC ASoC probe.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
There are no OSR controls on outputs 1-4 on wm5110, however when these
were removed the ones on output 5 and 6 were also accidentally removed,
but those actually exist. This patch adds these controls back in.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Conflicts:
tools/perf/bench/numa.c
Pull perf fixes from Jiri Olsa.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Pick up the latest fixes.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
