| Age | Commit message (Collapse) | Author |
|---|
|
This patch add a LED class driver for the dual-GPIO LEDs found on the
Network Space v2 board (and parents). This include Internet Space v2,
Network Space (Max) v2 and d2 Network v2 boards.
This dual-GPIO LED is wired to a CPLD and can blink in relation with the
SATA activity. The driver expose this capability through a "sata" sysfs
attribute.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
This patch extends the kirkwood's PCIe support up to 2 controllers as in the 6282 devices.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Add private_data pointer to the pci_sys_data, this pointer can be
used for holding platform specific data for each pci controller.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
The 6282 SoC is compatible to 6280 and features faster CPU, DDR3, additional
PCIe interface, and LCD controller. More information can be found here:
http://www.marvell.com/products/processors/embedded/armada_300/armada_310.pdf
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
In case the board is configured to boot from spi flash, the mpps
will not be configured to select the NAND I/Os. This patch makes
sure to select the NAND I/O's regardless to the boot device type.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Some platforms, such as the DNS-323 rev C requires the soft reset line
to be toggled on and back off for the reset to work.
Note: The choice of 200ms delay comes from the 2.6.12 based vendor kernel.
It seems to be a -lot- though and I had my device working fine with much
smaller delays but better safe...
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
This patch adds the base support for this new HW revision to the existing
dns323-setup.c file. The SoC seems to be the same as rev B1, the GPIOs
are all wired differently though and the fan control isn't i2c based
anymore.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
This moves the various known Marvell PHY IDs to include/linux/marvell_phy.h
along with dev_flags definitions for use by the driver.
I then added a flag that changes the PHY init code to setup the LEDs
config to the values needed to operate a dns323 rev C1 NAS.
I moved the existing "resistance" flag to the .h as well, though I've
been unable to find whoever sets this to convert it to use that constant.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
This patch adds support for the OpenRD Ultimate machine (could be found
at http://www.arm.linux.org.uk/developer/machines/list.php?id=2884)
Signed-off-by: Dmytro Milinevskyy <milinevskyy@gmail.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Patch found in QNAPs vendor source package, with some cleanups
(proper defines, shortened max. timeout from 1s to 200ms).
Without this patch the PCIe SATA controller (Marvell 88sx7042/sata_mv)
in my QNAP TS-419P (Marvell 88f6281/Kirkwood) stops working after a
few minutes.
The symptomes are described in this thread:
http://marc.info/?l=linux-ide&m=124822863706181&w=2
[ Note: this is a workaround in need of a better analysis/solution -- NP ]
Acked-by: Saeed Bishara <saeed@marvell.com>
Tested-by: Bernhard R. Link <brl@pcpool00.mathematik.uni-freiburg.de>
Seconded-by: Martin Michlmayr <tbm@cyrius.com>
I'm_not_very_happy_with_it-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Add support for the HP t5325 Thin Client. This thin client is based
on a Marvell Kirkwood chip at 1.2 GHz and features 512 MB RAM, 512 MB
SATA-attached flash and an XGI Volari Z11 GPU.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
MPP44 can be used to differentiate between one-bay (TS-11x) and
two-bay (TS-21x) devices.
According to an engineer from QNAP, the setting of MPP44 depends
on the firmware rather than hardware. Presumably, this means
that you could fake the MPP44 value by changing the boot loader.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Add MPP definitions for Marvell Kirkwood 88F6282 revision.
Update some defines to reflect datasheet's MPP names.
Signed-off-by: Benjamin Zores <benjamin.zores@alcatel-lucent.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Among other changes, commit b2a731aa ("D-link DNS-323 revision A1 power
LED") changed the default behaviour of the power LED from solid to
blinking. This was done to match the original DNS-323 firmware which
blinks during the boot process and sets the LED to solid when booting
has completed. However, the downside of this behaviour is that it
requires userland code to change the LED, even for those who don't
care about the behaviour of the original firmware. Therefore, change
it to solid again and let those who care about the original behaviour
change the behaviour from userland.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
On the QNAP TS-41x, MPP45 is used to show the setting of jumper JP1.
Fix the documentation to explain what the settings really indicate.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Export GPIO 45 which is used to indicate the setting of the JP1
jumper. This is useful for userland tools, such as qcontrol, to
see whether the LCD or a serial console is connected.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Fix the following warning :
WARNING: vmlinux.o(.text+0x95a0): Section mismatch in reference from the
function qnap_tsx1x_register_flash() to the (unknown reference) .init.data:(unknown)
The function qnap_tsx1x_register_flash() references
the (unknown reference) __initdata (unknown).
This is often because qnap_tsx1x_register_flash lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
|
|
The fixed bar capability structure is searched in PCI extended
configuration space. We need to make sure there is a valid capability
ID to begin with otherwise, the search code may stuck in a infinite
loop which results in boot hang. This patch adds additional check for
cap ID 0, which is also invalid, and indicates end of chain.
End of chain is supposed to have all fields zero, but that doesn't
seem to always be the case in the field.
Suggested-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
LKML-Reference: <1279306706-27087-1-git-send-email-jacob.jun.pan@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Found one x2apic system kexec loop test failed
when CONFIG_NMI_WATCHDOG=y (old) or CONFIG_LOCKUP_DETECTOR=y (current tip)
first kernel can kexec second kernel, but second kernel can not kexec third one.
it can be duplicated on another system with BIOS preenabled x2apic.
First kernel can not kexec second kernel.
It turns out, when kernel boot with pre-enabled x2apic, it will not execute
disable_local_APIC on shutdown path.
when init_apic_mappings() is called in setup_arch, it will skip setting of
apic_phys when x2apic_mode is set. ( x2apic_mode is much early check_x2apic())
Then later, disable_local_APIC() will bail out early because !apic_phys.
So check !x2apic_mode in x2apic_mode in disable_local_APIC with !apic_phys.
another solution could be updating init_apic_mappings() to set apic_phys even
for preenabled x2apic system. Actually even for x2apic system, that lapic
address is mapped already in early stage.
BTW: is there any x2apic preenabled system with apicid of boot cpu > 255?
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4C3EB22B.3000701@kernel.org>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: stable@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
ocfs2_write_zero_page() has a loop that won't ever be skipped, but gcc
doesn't know that. Set ret=0 just to make gcc happy.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
The order of freeing the IRQ and freeing the device in firmware
in ibmveth_close can cause the adapter to become unusable after a
subsequent ibmveth_open. Only a reboot of the OS will make the
network device usable again. This is seen when cycling the adapter
up and down while there is network activity.
There is a window where an IRQ will be left unserviced (H_EOI will not
be called). The solution is to make a VIO_IRQ_DISABLE h_call, free the
device with firmware, and then call free_irq.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
|
|
If we fail to assign resources to a PCI BAR, this patch makes us try the
original address from BIOS rather than leaving it disabled.
Linux tries to make sure all PCI device BARs are inside the upstream
PCI host bridge or P2P bridge apertures, reassigning BARs if necessary.
Windows does similar reassignment.
Before this patch, if we could not move a BAR into an aperture, we left
the resource unassigned, i.e., at address zero. Windows leaves such BARs
at the original BIOS addresses, and this patch makes Linux do the same.
This is a bit ugly because we disable the resource long before we try to
reassign it, so we have to keep track of the BIOS BAR address somewhere.
For lack of a better place, I put it in the struct pci_dev.
I think it would be cleaner to attempt the assignment immediately when the
claim fails, so we could easily remember the original address. But we
currently claim motherboard resources in the middle, after attempting to
claim PCI resources and before assigning new PCI resources, and changing
that is a fairly big job.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16263
Reported-by: Andrew <nitr0@seti.kr.ua>
Tested-by: Andrew <nitr0@seti.kr.ua>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Add alignment to syscall metadata declarations
perf: Sync callchains with period based hits
perf: Resurrect flat callchains
perf: Version String fix, for fallback if not from git
perf: Version String fix, using kernel version
|
|
The rt2x00dev->intf_work workqueue is never initialized when a driver is
probed for a non-existent device (in this case rt2500usb). On such a
path we call rt2x00lib_remove_dev() to free any resources initialized
during the probe before we use INIT_WORK to initialize the workqueue.
This causes lockdep to get confused since the lock used in the workqueue
hasn't been initialized yet but is now being acquired during
cancel_work_sync() called by rt2x00lib_remove_dev().
Fix this by initializing the workqueue first before we attempt to probe
the device. This should make lockdep happy and avoid breaking any
assumptions about how the library cleans up after a probe fails.
phy0 -> rt2x00lib_probe_dev: Error - Failed to allocate device.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 2027, comm: modprobe Not tainted 2.6.35-rc5+ #60
Call Trace:
[<ffffffff8105fe59>] register_lock_class+0x152/0x31f
[<ffffffff81344a00>] ? usb_control_msg+0xd5/0x111
[<ffffffff81061bde>] __lock_acquire+0xce/0xcf4
[<ffffffff8105f6fd>] ? trace_hardirqs_off+0xd/0xf
[<ffffffff81492aef>] ? _raw_spin_unlock_irqrestore+0x33/0x41
[<ffffffff810628d5>] lock_acquire+0xd1/0xf7
[<ffffffff8104f037>] ? __cancel_work_timer+0x99/0x17e
[<ffffffff8104f06e>] __cancel_work_timer+0xd0/0x17e
[<ffffffff8104f037>] ? __cancel_work_timer+0x99/0x17e
[<ffffffff8104f136>] cancel_work_sync+0xb/0xd
[<ffffffffa0096675>] rt2x00lib_remove_dev+0x25/0xb0 [rt2x00lib]
[<ffffffffa0096bf7>] rt2x00lib_probe_dev+0x380/0x3ed [rt2x00lib]
[<ffffffff811d78a7>] ? __raw_spin_lock_init+0x31/0x52
[<ffffffffa00bbd2c>] ? T.676+0xe/0x10 [rt2x00usb]
[<ffffffffa00bbe4f>] rt2x00usb_probe+0x121/0x15e [rt2x00usb]
[<ffffffff813468bd>] usb_probe_interface+0x151/0x19e
[<ffffffff812ea08e>] driver_probe_device+0xa7/0x136
[<ffffffff812ea167>] __driver_attach+0x4a/0x66
[<ffffffff812ea11d>] ? __driver_attach+0x0/0x66
[<ffffffff812e96ca>] bus_for_each_dev+0x54/0x89
[<ffffffff812e9efd>] driver_attach+0x19/0x1b
[<ffffffff812e9b64>] bus_add_driver+0xb4/0x204
[<ffffffff812ea41b>] driver_register+0x98/0x109
[<ffffffff813465dd>] usb_register_driver+0xb2/0x173
[<ffffffffa00ca000>] ? rt2500usb_init+0x0/0x20 [rt2500usb]
[<ffffffffa00ca01e>] rt2500usb_init+0x1e/0x20 [rt2500usb]
[<ffffffff81000203>] do_one_initcall+0x6d/0x17a
[<ffffffff8106cae8>] sys_init_module+0x9c/0x1e0
[<ffffffff8100296b>] system_call_fastpath+0x16/0x1b
Signed-off-by: Stephen Boyd <bebarino@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Strip the cap and dentry releases from replayed messages. They can
cause the shared state to get out of sync because they were generated
(with the request message) earlier, and no longer reflect the current
client state.
Signed-off-by: Sage Weil <sage@newdream.net>
|
|
Replayed rename operations (after an mds failure/recovery) were broken
because the request paths were regenerated from the dentry names, which
get mangled when d_move() is called.
Instead, resend the previous request message when replaying completed
operations. Just make sure the REPLAY flag is set and the target ino is
filled in.
This fixes problems with workloads doing renames when the MDS restarts,
where the rename operation appears to succeed, but on mds restart then
fails (leading to client confusion, app breakage, etc.).
Signed-off-by: Sage Weil <sage@newdream.net>
|
|
When I ran "perf kvm ... top", I encountered the following error output.
Error: perfcounter syscall returned with -1 (Too many open files)
Fatal: No CONFIG_PERF_EVENTS=y kernel support configured?
Looking into perf, I found perf opens too many directories at
initialization time, but forgets to close them. Here is the fix.
LKML-Reference: <4C230362.5080704@cn.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Gui Jianfeng <guijianfeng@cn.fujitsu.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
GFS2: rename causes kernel Oops
GFS2: BUG in gfs2_adjust_quota
GFS2: Fix kernel NULL pointer dereference by dlm_astd
GFS2: recovery stuck on transaction lock
GFS2: O_TRUNC not working on stuffed files across cluster
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: w90p910_ts - fix call to setup_timer()
Input: synaptics - fix wrong dimensions check
Input: i8042 - mark stubs in i8042.h "static inline"
|
|
Conflicts:
arch/arm/configs/lusl7200_defconfig
|
|
Add a common early allocator function, in preparation for switching
over to LMB. When we do, this function will need to do a little more
than just allocating memory; we need it zero initialized too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The logic in this file is rather convoluted, but essentially:
1. region type 0 is SDRAM
2. referring to the code fragment
if (set_fbmem_region_type(&rg, OMAPFB_MEMTYPE_SDRAM,
sdram_start, sdram_size) < 0 ||
(rg.type != OMAPFB_MEMTYPE_SDRAM))
continue;
- if rg.type is not OMAPFB_MEMTYPE_SDRAM, set_fbmem_region_type()
returns zero immediately (since rg.type is non-zero), and so we
'continue'.
- if rg.type is OMAPFB_MEMTYPE_SDRAM, and rg.paddr is zero,
we fall through.
- if rg.type is OMAPFB_MEMTYPE_SDRAM, and the region lies within
SDRAM, we fall through.
- if rg.type is OMAPFB_MEMTYPE_SDRAM, and the region is not within
SDRAM, we 'continue'.
3. check_fbmem_region seems unnecessary.
- we know rg.type is OMAPFB_MEMTYPE_SDRAM
- we can check rg.size independently
- bootmem_reserve() can check for overlapping reservations itself
- we've already validated that the requested region lies within SDRAM.
4. avoid BUG()ing if the region entry is already set; print an error,
and mark the configuration invalid - at least we'll continue booting
so the error message has a chance of being logged/visible via serial
console.
With these changes in place, it makes the code much easier to understand
and hence easier to convert to LMB.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Move the platform specific bootmem memory reservations out of
arch/arm/mm/mmu.c into their respective platform files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Since we no longer support discontigmem, node is always zero, so
remove this argument.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Everything should now be using sparsemem rather than discontigmem, so
remove the code supporting discontigmem from ARM.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Rather than storing the minimum size of the vmalloc area, store the
maximum permitted address of the vmalloc area instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Guest can trigger packet truncation by posting
a very short buffer and disabling buffer merging.
Convert pr_err to pr_debug to avoid log from filling
up when this happens.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
No need to take address, w90p910_ts is already a pointer.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
This was detected using two mcast router tables. The
pimreg for the second interface did not have a specific
mrule, so packets received by it were handled by the
default table, which had nothing configured.
This caused the ipmr_fib_lookup to fail, causing
the memory leak.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: skcipher - avoid NULL dereference
|
|
Hists that have been filtered, because they don't have callchains
matching the parent filter, won't be printed. As such,
hist_entry__snprintf() returns 0 for them, but we don't control
this value and we always print the buffer, which might be
untouched and then only made of random stack garbage.
Not only does it paint the screen with barf, it also prints
the callchains for these hists, even though they have been filtered,
since the hist has been filtered as well.
We need to check the return value of hist_entry__snprintf() and
ignore the hist if it is 0, which means it didn't get any callchain
matching the parent filter. This fixes the barf and the undesired
callchains.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
|
|
The asics in question have the following requirements with regard to
their gart setups:
1. The GART aperture size has to be in the form of 2^X bytes, where X is from 25 to 31
2. The GART aperture MC base has to be aligned to a boundary equal to the size of the
aperture.
3. The GART page table has to be aligned to the boundary equal to the size of the table.
4. The GART page table size is: table_entry_size * (aperture_size / page_size)
5. The GART page table has to be allocated in non-paged, non-cached, contiguous system
memory.
This patch takes care 2. The rest should already be handled properly.
This fixes a regression noticed by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
OCFS2 uses t_commit trigger to compute and store checksum of the just
committed blocks. When a buffer has b_frozen_data, checksum is computed
for it instead of b_data but this can result in an old checksum being
written to the filesystem in the following scenario:
1) transaction1 is opened
2) handle1 is opened
3) journal_access(handle1, bh)
- This sets jh->b_transaction to transaction1
4) modify(bh)
5) journal_dirty(handle1, bh)
6) handle1 is closed
7) start committing transaction1, opening transaction2
8) handle2 is opened
9) journal_access(handle2, bh)
- This copies off b_frozen_data to make it safe for transaction1 to commit.
jh->b_next_transaction is set to transaction2.
10) jbd2_journal_write_metadata() checksums b_frozen_data
11) the journal correctly writes b_frozen_data to the disk journal
12) handle2 is closed
- There was no dirty call for the bh on handle2, so it is never queued for
any more journal operation
13) Checkpointing finally happens, and it just spools the bh via normal buffer
writeback. This will write b_data, which was never triggered on and thus
contains a wrong (old) checksum.
This patch fixes the problem by calling the trigger at the moment data is
frozen for journal commit - i.e., either when b_frozen_data is created by
do_get_write_access or just before we write a buffer to the log if
b_frozen_data does not exist. We also rename the trigger to t_frozen as
that better describes when it is called.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
