summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-03-30pwm: sun4i: Remove redundant needs_delayPascal Roeleven
'needs_delay' does now always evaluate to true, so remove all occurrences. Signed-off-by: Pascal Roeleven <dev@pascalroeleven.nl> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: omap-dmtimer: Implement .apply callbackLokesh Vutla
Implement .apply callback and drop the legacy callbacks(enable, disable, config, set_polarity). In .apply() check for the current hardware status before changing the PWM configuration. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: omap-dmtimer: Do not disable PWM before changing period/duty_cycleLokesh Vutla
Only the Timer control register(TCLR) cannot be updated when the timer is running. Registers like Counter register (TCRR), loader register (TLDR) and match register (TMAR) can be updated while the counter is running. Since TCLR is not updated in pwm_omap_dmtimer_config(), do not stop the timer for period/duty_cycle update. Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: omap-dmtimer: Fix PWM enabling sequenceLokesh Vutla
To configure DM timer in PWM mode the following needs to be set in OMAP_TIMER_CTRL_REG using set_pwm callback: - Set toggle mode on PORTIMERPWM output pin - Set trigger on overflow and match on PORTIMERPWM output pin. - Set auto reload This is a one time configuration and needs to be set before the start of the DM timer. But the current driver tries to set the same configuration for every period/duty cycle update, which is not needed. So move the PWM setup before enabling timer and do not update it in pwm_omap_dmtimer_config(). Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: omap-dmtimer: Update description for PWM OMAP DM timerLokesh Vutla
Update the description with a brief about how PWM is generated using OMAP DM timer and add limitations for the PWM generations. Also add a link to the reference manual. Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: omap-dmtimer: Drop unused header fileLokesh Vutla
pwm_omap_dmtimer.h is used only: - to typedef struct omap_dm_timer to pwm_omap_dmtimer - for macro PWM_OMAP_DMTIMER_TRIGGER_OVERFLOW_AND_COMPARE Rest of the file is pretty mush unsed. So reuse omap_dm_timer and OMAP_TIMER_TRIGGER_OVERFLOW_AND_COMPARE in pwm-omap-dmtimer.c and delete the header file. Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: renesas-tpu: Drop confusing registered messageGeert Uytterhoeven
During device probe, the message TPU PWM -1 registered is printed. While the "-1" looks suspicious, it is perfectly normal for a device instantiated from DT. Remove the message, as there are no non-DT users left, and other drivers don't print such messages either. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: renesas-tpu: Fix late Runtime PM enablementGeert Uytterhoeven
Runtime PM should be enabled before calling pwmchip_add(), as PWM users can appear immediately after the PWM chip has been added. Likewise, Runtime PM should always be disabled after the removal of the PWM chip, even if the latter failed. Fixes: 99b82abb0a35b073 ("pwm: Add Renesas TPU PWM driver") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: rcar: Fix late Runtime PM enablementGeert Uytterhoeven
Runtime PM should be enabled before calling pwmchip_add(), as PWM users can appear immediately after the PWM chip has been added. Likewise, Runtime PM should be disabled after the removal of the PWM chip. Fixes: ed6c1476bf7f16d5 ("pwm: Add support for R-Car PWM Timer") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30dt-bindings: pwm: renesas-tpu: Document more R-Car Gen2 supportGeert Uytterhoeven
All R-Car Gen2 SoCs have a Renesas Timer Pulse Unit. Document support for the missing variants. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: meson: Fix confusing indentationKrzysztof Kozlowski
Fix indentation of return block. Smatch warning: drivers/pwm/pwm-meson.c:139 meson_pwm_request() warn: inconsistent indenting Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Fixes: 211ed630753d ("pwm: Add support for Meson PWM Controller") Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: pca9685: Use gpio core provided macro GPIO_LINE_DIRECTION_OUTRishi Gupta
GPIO core recently added macro to uniformly specify direction of a GPIO line, so use it. Signed-off-by: Rishi Gupta <gupt21@gmail.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: pca9685: Replace CONFIG_PM with __maybe_unusedRishi Gupta
The __maybe_unused attribute is preferred over CONFIG_PM to prevent potential build time issues. This commit replaces CONFIG_PM with this attribute. Signed-off-by: Rishi Gupta <gupt21@gmail.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: tegra: Add support for Tegra194Sandipan Patra
Tegra194 has multiple PWM controllers with each having only one output. Also the maxmimum frequency is higher than earlier SoCs. Add support for Tegra194 and specify the number of PWM outputs and maximum supported frequency using device tree match data. Signed-off-by: Sandipan Patra <spatra@nvidia.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Laxman Dewangan <ldewangan@nvidia.com> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: Enable compile testing for some of driversKrzysztof Kozlowski
Some of the PWM drivers can be compile tested to increase build coverage. The Meson PWM driver requires COMMON_CLK dependency. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Florian Fainelli <f.fainelli@gmail.com> # For Broadcoam Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # For Meson Acked-by: Claudiu Beznea <claudiu.beznea@microchip.com> # For Atmel Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30x86/xen: Make the secondary CPU idle tasks reliableMiroslav Benes
The unwinder reports the secondary CPU idle tasks' stack on XEN PV as unreliable, which affects at least live patching. cpu_initialize_context() sets up the context of the CPU through VCPUOP_initialise hypercall. After it is woken up, the idle task starts in cpu_bringup_and_idle() function and its stack starts at the offset right below pt_regs. The unwinder correctly detects the end of stack there but it is confused by NULL return address in the last frame. Introduce a wrapper in assembly, which just calls cpu_bringup_and_idle(). The return address is thus pushed on the stack and the wrapper contains the annotation hint for the unwinder regarding the stack state. Signed-off-by: Miroslav Benes <mbenes@suse.cz> Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com>
2020-03-30x86/xen: Make the boot CPU idle task reliableMiroslav Benes
The unwinder reports the boot CPU idle task's stack on XEN PV as unreliable, which affects at least live patching. There are two reasons for this. First, the task does not follow the x86 convention that its stack starts at the offset right below saved pt_regs. It allows the unwinder to easily detect the end of the stack and verify it. Second, startup_xen() function does not store the return address before jumping to xen_start_kernel() which confuses the unwinder. Amend both issues by moving the starting point of initial stack in startup_xen() and storing the return address before the jump, which is exactly what call instruction does. Signed-off-by: Miroslav Benes <mbenes@suse.cz> Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com>
2020-03-30xen-pciback: fix INTERRUPT_TYPE_* definesMarek Marczykowski-Górecki
xen_pcibk_get_interrupt_type() assumes INTERRUPT_TYPE_NONE being 0 (initialize ret to 0 and return as INTERRUPT_TYPE_NONE). Fix the definition to make INTERRUPT_TYPE_NONE really 0, and also shift other values to not leave holes. But also, do not assume INTERRUPT_TYPE_NONE being 0 anymore to avoid similar confusions in the future. Fixes: 476878e4b2be ("xen-pciback: optionally allow interrupt enable flag writes") Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Reviewed-by: Roger Pau Monné <roger.pau@citrix.com> Signed-off-by: Juergen Gross <jgross@suse.com>
2020-03-30xen/xenbus: remove unused xenbus_map_ring()Juergen Gross
xenbus_map_ring() is used nowhere in the tree, remove it. xenbus_unmap_ring() is used only locally, so make it static and move it up. Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Juergen Gross <jgross@suse.com>
2020-03-30PCI: sysfs: Revert "rescan" file renamesKelsey Skunberg
We changed these sysfs filenames: .../pci_bus/<domain:bus>/rescan -> .../pci_bus/<domain:bus>/bus_rescan .../<domain:bus:dev.fn>/rescan -> .../<domain:bus:dev.fn>/dev_rescan and Ruslan reported [1] that this broke a userspace application. Revert these name changes so both files are named "rescan" again. Note that we have to use __ATTR() to assign custom C symbols, i.e., "struct device_attribute <symbol>". [1] https://lore.kernel.org/r/CAB=otbSYozS-ZfxB0nCiNnxcbqxwrHOSYxJJtDKa63KzXbXgpw@mail.gmail.com [bhelgaas: commit log, use __ATTR() both places so we don't have to rename the attributes] Fixes: 8bdfa145f582 ("PCI: sysfs: Define device attributes with DEVICE_ATTR*()") Fixes: 4e2b79436e4f ("PCI: sysfs: Change DEVICE_ATTR() to DEVICE_ATTR_WO()") Link: https://lore.kernel.org/r/20200325151708.32612-1-skunberg.kelsey@gmail.com Signed-off-by: Kelsey Skunberg <kelsey.skunberg@gmail.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: stable@vger.kernel.org # v5.4+
2020-03-30pwm: pca9685: Remove unused duty_cycle struct elementMatthias Schiffer
duty_cycle was only set, never read. Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: mxs: Remove unused include of of_address.hAnson Huang
There is nothing in use from of_address.h, remove it. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: imx27: Remove unused include of of_device.hAnson Huang
There is nothing in use from of_device.h, remove it. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: imx-tpm: Remove unused includesAnson Huang
There is nothing in use from log2.h/of_address.h, remove them. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: Implement some checks for lowlevel driversUwe Kleine-König
There are some expectations which the callbacks provided by lowlevel drivers should fulfill. Implement checks that help driver authors to get these semantics right. As these have some overhead the checks can be disabled using a Kconfig setting. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: imx27: Ensure clocks being on iff the PWM is onUwe Kleine-König
Up to now the .probe() function didn't enable clocks and relied on the core to call the .get_state() callback to have the clock running. The latter enabled the needed clocks and kept them running if the PWM wass enabled. This only works correctly if the .get_state() callback is called exactly once and this single call happens before unused clocks are disabled by the clk core. The former wasn't true for a short period while commit 01ccf903edd6 ("pwm: Let pwm_get_state() return the last implemented state") applied and not reverted yet and might become wrong in the future. The latter isn't true any more since commit cfc4c189bc70 ("pwm: Read initial hardware state at request time") which results in a running PWM being stopped at boot time if for example the consumer lives in a kernel module that is only loaded after the clk core disabled unused clocks. So ensure .probe() is left with the clocks on if the PWM is running and .get_state() disables everything it enabled. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: imx27: Don't disable clocks at device remove timeUwe Kleine-König
The .remove() callback is not supposed to modify hardware state. This is in the responsibility of the PWM consumer. After the PWM was disabled the clocks are off (apart from a bug that is fixed in the next patch), so unbinding the driver either stops the PWM (which it should not) or disables already disabled clocks yielding warnings from the clk core. So just drop the call to disable the clocks. (Which BTW was also in the wrong order because the call makes the PWM unfunctional and so should have come only after pwmchip_remove()). Fixes: 9f4c8f9607c3 ("pwm: imx: Add ipg clock operation") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: imx27: Simplify helper function to enable and disable clocksUwe Kleine-König
pwm_imx27_clk_prepare_enable() took a pointer to a struct pwm_chip just to convert it to a struct pwm_imx27_chip pointer while all callers already have the latter. Ditto for pwm_imx27_clk_disable_unprepare(). Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: imx27: Fix clock handling in pwm_imx27_apply()Uwe Kleine-König
pwm_imx27_apply() enables the clocks if the previous PWM state was disabled. Given that the clocks are supposed to be left on iff the PWM is running, the decision to disable the clocks at the end of the function must not depend on the previous state. Without this fix the enable count of the two affected clocks increases by one whenever ->apply() changes from one disabled state to another. Fixes: bd88d319abe9 ("pwm: imx27: Unconditionally write state to hardware") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: bcm2835: Dynamically allocate baseFlorian Fainelli
The newer 2711 and 7211 chips have two PWM controllers and failure to dynamically allocate the PWM base would prevent the second PWM controller instance being probed for succeeding with an -EEXIST error from alloc_pwms(). Fixes: e5a06dc5ac1f ("pwm: Add BCM2835 PWM driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30dt-bindings: pwm: Convert google,cros-ec-pwm.txt to YAML formatDafna Hirschfeld
Convert the binding file google,cros-ec-pwm.txt to YAML format. This was tested and verified on ARM64 with: make dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/pwm/google,cros-ec-pwm.yaml make dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/pwm/google,cros-ec-pwm.yaml Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30Merge branch 'timers/drivers/timer-ti-dm' of ↵Thierry Reding
https://git.linaro.org/people/dlezcano/linux into for-next
2020-03-30alpha: Fix nautilus PCI setupIvan Kokshaysky
Example (hopefully reasonable) of the new "size_windows" flag usage. Fixes accidental breakage caused by f75b99d5a77d ("PCI: Enforce bus address limits in resource allocation"). Fixes: f75b99d5a77d ("PCI: Enforce bus address limits in resource allocation") Link: https://lore.kernel.org/r/20200318005029.GA8326@mail.rc.ru Tested-by: Matt Turner <mattst88@gmail.com> Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2020-03-30PCI: Add support for root bus sizingIvan Kokshaysky
In certain cases we should be able to enumerate IO and MEM ranges of all PCI devices installed in the system, and then set respective host bridge apertures basing on calculated size and alignment. Particularly when firmware is broken and fails to assign bridge windows properly, like on Alpha UP1500 platform. Actually, almost everything is already in place, and required changes are minimal: - add "size_windows" flag to struct pci_host_bridge: when set, it instructs __pci_bus_size_bridges() to continue with the root bus; - in the __pci_bus_size_bridges() path: add checks for bus->self, as it can legitimately be null for the root bus. Link: https://lore.kernel.org/r/20200314194355.GA12510@mail.rc.ru Tested-by: Matt Turner <mattst88@gmail.com> Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2020-03-30PCI: Use ioremap(), not phys_to_virt() for platform ROMMikel Rychliski
On some EFI systems, the video BIOS is provided by the EFI firmware. The boot stub code stores the physical address of the ROM image in pdev->rom. Currently we attempt to access this pointer using phys_to_virt(), which doesn't work with CONFIG_HIGHMEM. On these systems, attempting to load the radeon module on a x86_32 kernel can result in the following: BUG: unable to handle page fault for address: 3e8ed03c #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page *pde = 00000000 Oops: 0000 [#1] PREEMPT SMP CPU: 0 PID: 317 Comm: systemd-udevd Not tainted 5.6.0-rc3-next-20200228 #2 Hardware name: Apple Computer, Inc. MacPro1,1/Mac-F4208DC8, BIOS MP11.88Z.005C.B08.0707021221 07/02/07 EIP: radeon_get_bios+0x5ed/0xe50 [radeon] Code: 00 00 84 c0 0f 85 12 fd ff ff c7 87 64 01 00 00 00 00 00 00 8b 47 08 8b 55 b0 e8 1e 83 e1 d6 85 c0 74 1a 8b 55 c0 85 d2 74 13 <80> 38 55 75 0e 80 78 01 aa 0f 84 a4 03 00 00 8d 74 26 00 68 dc 06 EAX: 3e8ed03c EBX: 00000000 ECX: 3e8ed03c EDX: 00010000 ESI: 00040000 EDI: eec04000 EBP: eef3fc60 ESP: eef3fbe0 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 EFLAGS: 00010206 CR0: 80050033 CR2: 3e8ed03c CR3: 2ec77000 CR4: 000006d0 Call Trace: r520_init+0x26/0x240 [radeon] radeon_device_init+0x533/0xa50 [radeon] radeon_driver_load_kms+0x80/0x220 [radeon] drm_dev_register+0xa7/0x180 [drm] radeon_pci_probe+0x10f/0x1a0 [radeon] pci_device_probe+0xd4/0x140 Fix the issue by updating all drivers which can access a platform provided ROM. Instead of calling the helper function pci_platform_rom() which uses phys_to_virt(), call ioremap() directly on the pdev->rom. radeon_read_platform_bios() previously directly accessed an __iomem pointer. Avoid this by calling memcpy_fromio() instead of kmemdup(). pci_platform_rom() now has no remaining callers, so remove it. Link: https://lore.kernel.org/r/20200319021623.5426-1-mikel@mikelr.com Signed-off-by: Mikel Rychliski <mikel@mikelr.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Alex Deucher <alexander.deucher@amd.com>
2020-03-30ASoC: AMD: Clear format bits before setting themAkshu Agrawal
This avoids residual bit form previous format when the format is changed. Hence, the resultant format is not an invalid one. Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com> Signed-off-by: Ravulapati Vishnu vardhan rao <Vishnuvardhanrao.Ravulapati@amd.com> Link: https://lore.kernel.org/r/20200328093921.32211-1-akshu.agrawal@amd.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-03-30ASoC: bcm: Fix pointer cast warningTakashi Iwai
The NULL check can be done gracefully without cast. It fixes a compile warning like: sound/soc/bcm/bcm63xx-pcm-whistler.c:184:6: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast] Fixes: 88eb404ccc3e ("ASoC: brcm: Add DSL/PON SoC audio driver") Signed-off-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20200330135645.9707-1-tiwai@suse.de Signed-off-by: Mark Brown <broonie@kernel.org>
2020-03-30dt-bindings: sound: cs42l51: Remove unneeded I2C unit nameFabio Estevam
The following warning is seen with 'make dt_binding_check': Documentation/devicetree/bindings/sound/cirrus,cs42l51.example.dts:18.15-34.11: Warning (unit_address_vs_reg): /example-0/i2c@0: node has a unit name, but no reg or ranges property Fix it by removing the unneeded i2c unit name. Signed-off-by: Fabio Estevam <festevam@gmail.com> Acked-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20200327155721.7596-1-festevam@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-03-30Merge tag 'kvm-s390-next-5.7-3' of ↵Paolo Bonzini
git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD KVM: s390: Fix for error codes - return the proper error to userspace when a signal interrupts the KSM unsharing operation
2020-03-30gfs2: Fix oversight in gfs2_ail1_flushBob Peterson
Ordinarily, function gfs2_ail1_start_one issues a write request for one item on the ail1 list, then returns -EBUSY. This makes the caller, gfs2_ail1_flush, loop around and start another. However, it was not clearing the -EBUSY return code each time through the loop. So on rare occasions, like when the wbc runs out of nr_to_write, it remained set to -EBUSY, which triggered an error and withdraw. This patch sets the return code to 0 each time through the restart loop so this won't happen anymore. Signed-off-by: Bob Peterson <rpeterso@redhat.com>
2020-03-30Merge branches 'acpi-ec', 'acpi-fan' and 'acpi-pci'Rafael J. Wysocki
* acpi-ec: ACPI: EC: Eliminate EC_FLAGS_QUERY_HANDSHAKE ACPI: EC: Do not clear boot_ec_is_ecdt in acpi_ec_add() ACPI: EC: Simplify acpi_ec_ecdt_start() and acpi_ec_init() ACPI: EC: Consolidate event handler installation code ACPI: EC: Use fast path in acpi_ec_add() for DSDT boot EC ACPI: EC: Simplify acpi_ec_add() ACPI: EC: Drop AE_NOT_FOUND special case from ec_install_handlers() ACPI: EC: Avoid passing redundant argument to functions ACPI: EC: Avoid printing confusing messages in acpi_ec_setup() * acpi-fan: ACPI: fan: Use scnprintf() for avoiding potential buffer overflow * acpi-pci: ACPI: PCI: Use scnprintf() for avoiding potential buffer overflow
2020-03-30Merge branches 'acpi-button', 'acpi-battery', 'acpi-osl', 'acpi-video' and ↵Rafael J. Wysocki
'acpi-misc' * acpi-button: ACPI: Add new tiny-power-button driver to directly signal init ACPI: button: move HIDs to acpi/button.h * acpi-battery: ACPI / battery: Cleanup Lenovo Ideapad Miix 320 DMI table entry ACPI / AC: Cleanup DMI quirk table * acpi-osl: ACPI: OSL: Add missing __acquires/__releases annotations * acpi-video: ACPI: video: remove redundant assignments to variable result * acpi-misc: ACPI: list_for_each_safe() -> list_for_each_entry_safe()
2020-03-30Merge branch 'acpica'Rafael J. Wysocki
* acpica: ACPICA: Update version to 20200214 ACPICA: Fix a couple of typos ACPICA: use acpi_size instead of u32 for prefix_path_length ACPICA: cast length arguement to acpi_ns_build_normalized_path() as u32 ACPICA: cast the result of the pointer difference to u32 ACPICA: Table Manager: Update comments in a function header ACPICA: Enable sleep button on ACPI legacy wake ACPICA: Fix a comment "enable" fixed events -> "disable" all fixed events. ACPICA: ASL-ASL+ converter: make root file a parameter for cv_init_file_tree ACPICA: ASL-ASL+ converter: remove function parameters from cv_init_file_tree()
2020-03-30ACPICA: Update version 20200326Bob Moore
ACPICA commit 994fe943d93fe18eaaed1b6cd725023399f8a5c6 Version 20200326. Link: https://github.com/acpica/acpica/commit/994fe943 Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Erik Kaneda <erik.kaneda@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-03-30ACPICA: Fixes for acpiExec namespace init fileBob Moore
This is the result of squashing the following ACPICA commit ID's: 6803997e5b4f3635cea6610b51ff69e29d251de3 f31cdf8bfda22fe265c1a176d0e33d311c82a7f7 This change fixes several problems with the support for the acpi_exec namespace init file (-fi option). Specifically, it fixes AE_ALREADY_EXISTS errors, as well as various seg faults. Link: https://github.com/acpica/acpica/commit/f31cdf8b Link: https://github.com/acpica/acpica/commit/6803997e Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Erik Kaneda <erik.kaneda@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-03-30ACPICA: Add NHLT table signatureCezary Rojewski
ACPICA commit 422166b656565d180bb3aac712009bdce5e70cdd NHLT (Non-HDAudio Link Table) provides configuration of audio endpoints for Intel SST (Smart Sound Technology) DSP products. Similarly to other ACPI tables, data provided by BIOS may not describe it correctly, thus overriding is required. ACPI override mechanism checks for unknown signature before proceeding. Update known signatures array to support NHLT. Link: https://github.com/acpica/acpica/commit/422166b6 Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Erik Kaneda <erik.kaneda@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-03-30ACPICA: WSMT: Fix typo, no functional changeErik Kaneda
ACPICA commit 764d18c5a83949ff3b0dbda6055cee1929b9caa2 The table signature WSMT stands for "Windows SMM Mitigations Table". It is not "Windows SMM Migrations Table". Link: https://github.com/acpica/acpica/commit/764d18c5 Reported-by: Laszlo Ersek <lersek@redhat.com> Signed-off-by: Erik Kaneda <erik.kaneda@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-03-30ACPICA: utilities: fix sprintf()John Levon
This contains changes for the following ACPICA commit ID's: 8f99a6ccd3b8e5c3d3d68c53fdbb054c2477eeb4 d30647af53abd334cbcf6362387464ea647bac9e d3c5fb4cf5b2880d789c987eb847fc3de3774abc On 32-bit, the provided sprintf() is non-functional: with a size of ACPI_UINT32_MAX, String + Size will wrap, meaning End < Start, and acpi_ut_bound_string_output() will never output anything as a result. The symptom we saw of this was acpixtract failing to output anything. Link: https://github.com/acpica/acpica/commit/8f99a6cc Link: https://github.com/acpica/acpica/commit/d30647af Link: https://github.com/acpica/acpica/commit/d3c5fb4c Signed-off-by: MSathieu <18145111+MSathieu@users.noreply.github.com> Signed-off-by: John Levon <john.levon@joyent.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Erik Kaneda <erik.kaneda@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-03-30ACPICA: acpiexec: remove redeclaration of acpi_gbl_db_opt_no_region_supportErik Kaneda
ACPICA commit 825c53661cacc7e3dab4844588201846143bd1b7 This variable was re-defined in a file specific to acpiexec. Remove the redundant declaration and move the initialize to the debugger. Patch based on suggestions by David Seifert and Benjamin Berg. Link: https://github.com/acpica/acpica/commit/825c5366 Reported-by: David Seifert <soap@gentoo.org> Reported-by: Benjamin Berg <bberg@redhat.com> Signed-off-by: Erik Kaneda <erik.kaneda@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-03-30ACPICA: Change PlatformCommChannel ASL keyword to PCCErik Kaneda
ACPICA commit 811e69a59cb4189ebf8b882eba74c881f598a239 The former was proposed during specification discussions but it was dropped. This keyword was introduced to the ACPICA code base by mistake so this commit changes the keyword representing Platform Communication Channel to be PCC. Link: https://github.com/acpica/acpica/commit/811e69a5 Signed-off-by: Erik Kaneda <erik.kaneda@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
generated by cgit (git 2.34.1) at 2025-09-17 00:24:37 +0000